SEARCH · Engineering Papers

Results for “THIN PLATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Improved Design For Birefringent Filter

Highly selective laser tuning achieved without thin plates of questionable optical quality. Improved birefringent filter developed for use with broad-band-emission laser. Provides improved narrow-band operation and wavelength selectivity. New filter design improves traditional design by providing method of increasing wavelength separation between highly transmitted peaks. Such broad-band lasers becoming popular in scientific laboratories and useful in military applications and separation of isotopes.

Bair, Clayton H.↗

NASA NTRS1992

Enhancing Control Of Helicopter Yaw At Low Speed

Spoilers on tail boom significantly improve yaw control in both right and left sidewinds. Spoilers are two thin plates extending outward, perpendicular to curvature of boom, distance of about 6 percent of total depth of tail boom. Along-the-boom dimensions of spoilers are as long as possible without interfering with such existing critical parts as tail rotor. Further enhancement, spoilers made retractable and automatically deployable as required. Concept applicable to all single-rotor helicopters. Applied as simple economical addition to existing helicopters or incorporated into new helicopter designs.

Kelley, Henry L.↗

NASA NTRS1991

Jetting and the origin of tektites

The scientific consensus is that tektites were produced by impacts on the Earth, but the exact mechanism by impacts might form tektites is still unclear. The most widely cited mechanism is jetting, which results from the extremely high pressures generated at the intersection of two bodies whose surfaces converge obliquely at high speed. Theory of jetting for thin plates is extended to the case of the impact of the sphere onto a half-space. The calculations are done for the impact of a silicate sphere onto a silicate target for impact speeds of 15, 20, and 25 km/sec, spanning the range of reasonable impact speeds for asteroids. The angle of impact is varied from 0 to 75 deg. The mass jetted, the jet velocity, projectile fraction in the jet, azimuthal distribution of the jet, and the phase of the jetted material are calculated as functions of time. The total mass jetted and the overall mass-averages of jet velocity, etc. are also calculated.

Vickery, A. M.↗

NASA NTRS1991

Birefringent filter design

A birefringent filter is provided for tuning the wavelength of a broad band emission laser. The filter comprises thin plates of a birefringent material having thicknesses which are non-unity, integral multiples of the difference between the thicknesses of the two thinnest plates. The resulting wavelength selectivity is substantially equivalent to the wavelength selectivity of a conventional filter which has a thinnest plate having a thickness equal to this thickness difference. The present invention obtains an acceptable tuning of the wavelength while avoiding a decrease in optical quality associated with conventional filters wherein the respective plate thicknesses are integral multiples of the thinnest plate.

Bair, Clayton H.↗

NASA NTRS1991

An adjustable RF tuning element for microwave, millimeter wave, and submillimeter wave integrated circuits

Planar RF circuits are used in a wide range of applications from 1 GHz to 300 GHz, including radar, communications, commercial RF test instruments, and remote sensing radiometers. These circuits, however, provide only fixed tuning elements. This lack of adjustability puts severe demands on circuit design procedures and materials parameters. We have developed a novel tuning element which can be incorporated into the design of a planar circuit in order to allow active, post-fabrication tuning by varying the electrical length of a coplanar strip transmission line. It consists of a series of thin plates which can slide in unison along the transmission line, and the size and spacing of the plates are designed to provide a large reflection of RF power over a useful frequency bandwidth. Tests of this structure at 1 GHz to 3 Ghz showed that it produced a reflection coefficient greater than 0.90 over a 20 percent bandwidth. A 2 GHz circuit incorporating this tuning element was also tested to demonstrate practical tuning ranges. This structure can be fabricated for frequencies as high as 1000 GHz using existing micromachining techniques. Many commercial applications can benefit from this micromechanical RF tuning element, as it will aid in extending microwave integrated circuit technology into the high millimeter wave and submillimeter wave bands by easing constraints on circuit technology.

Lubecke, Victor M.↗

NASA NTRS1991

Thermographic detection of cracks in thin sheets

A thermographic inspection technique for crack detection based on a 2D filter convolved with the thermal temperature images is presented. The filter is designed to approximate operating on the temperature images with a Laplacian operator. This operation yields an image which approximates changes in the heat flux in a thin plate. This filtering method results in an enhanced contrast due to the presence of cracks. Measurements have been performed on samples with fabricated electrical discharge machining (EDM) notches (both through-the-thickness and surface notches) and closed fatigue cracks around rivets. It is shown that the technique is effective for the detection of various crack lengths down to the resolution limits of the imager used.

Cramer, K. E.↗

NASA NTRS1992

Linear and non-linear failure analysis of composite laminates with transverse shear

A finite element computational procedure has been developed to find linear and nonlinear (von Karman) first-ply failure loads of composite laminates subjected to in-plane and transverse loads. The FEM is based on first-order shear deformation theory and several phenomenological failure criteria. It is found that the failure loads predicted by various failure criteria differ from one another by a maximum of 35 percent in the case of linear loads and 50 percent in the case of nonlinear loads; the failure locations differ from each other in a random way. It is demonstrated that the difference between the linear and nonlinear failure loads is large in the case of transversely loaded simply supported laminates and thin plates. The difference is found to be quite small in the case of in-plane (tensile) loading and thick laminates.

Reddy, Y. S. N.↗

NASA NTRS1992

Control of resonant frequencies in adaptive structures by prestressing

The natural vibration frequencies of a structure can be affected by inducing stress in the structure. The success of this kind of control of the resonant frequencies of a truss structure depends on the geometry of the structure. It is shown that in adaptive truss structures the method is effective for vibrations in less stiff directions, such as the normal direction of the plane containing all of the bars of a node, suggesting its applicability for cable, membrane, and thin plate and shell structures.

Baycan, Can M.↗

NASA NTRS1993

Finite element calculations of transonic flutter in cascades

Aeroelastic stability and response of turbomachinery cascades operating in the transonic regime are explored using a new computational approach. The two-dimensional unsteady Euler equations are used to model the transonic cascade flows, and the cascade blades are modeled as thin plates. To minimize the discretization incompatibility, both the fluid and the solid domains are discretized using finite element procedures. The fluid and the structural models are coupled at the element level by introducing a channel theory, which is analogous to a strip theory in the classical sense. The system of space-discretized equations is marched forward in time using an explicit four-stage Runge-Kutta scheme. Results of free vibration analyses of typical blades are presented and compared to published finite element and Rayleigh-Ritz results. Aeroelastic stability and response characteristics of several transonic cascades are investigated using the new quasi-3D model. These results demonstrate the present 3D finite element blade model is capable of capturing aeroelastic instabilities involving higher modes, including (plate-type) camber bending modes.

Hsiao, Chingteng↗

NASA NTRS1991

Jet ejecta mass upon oblique impact

Theoretical models in the jetting regime for symmetric and asymmetric impact of thin plates predict the mass and velocity of jetted material upon oblique impact. However, experimental constraints on the amount of material which form jets upon oblique impact are not known. A series of preliminary experiments were conducted in which tungsten (W) flyer plates at speeds of 1.5 to 2.0 km/s were obliquely impacted into carbon targets at 30 deg in the regime of jetting, yielding radiation temperatures in the about 3200 K range. Both framing-camera and flash X-ray imaging were conducted. Broad cm-sized craters induced by jet ejecta on 2024 Al witness plates were used to infer jet mass. We infer, from measured witness plate crater volumes, that jet masses in the range of 0.01 to 0.06 g are produced by a 32 mm diameter, 6 mm thick W impactor. This is about one to two orders of magnitude less than those calculated from present theoretical models. In contrast, in refractory material experiments, the mass of gabbro ejecta trapped in styrofoam is 0.52 g, which is similar to that calculated.

Yang, W.↗

NASA NTRS1921

Effect of the Reversal of Air Flow upon the Discharge Coefficient of Durley Orifices

Experiments were conducted to obtain information on the relationship between the coefficients for flow in two directions through thin plate orifices at low velocities. The results indicate that the ratio of the orifice discharge coefficient from standard orifice C(sub s)(sup 1) to the discharge coefficient from the reverse flow C(sub s) is always less than unity with increasing ratio of box area to orifice area. Even for areas as low as twenty, the ratios of the coefficients are not much less than unity. It is probable, however, that when the ratio of box area is less than twenty, the ratio of discharge coefficients would be greatly reduced. Specific results are given for the case of an apparatus for the laboratory testing of superchargers.

Ware, Marsden↗

NASA NTRS1930

Strength in Shear of the Thin Curved Sheets of Alclad

This note is on an investigation made to obtain information on the strength of thin curved sheets of Alclad in shear. Designers may utilize this material as a strength member as well as for a covering for the wings and fuselages. A reduction may then be made in the size of the internal strength members. These experiments were undertaken with the object of securing the maximum value from the metal in this respect. The point at which buckling occurs is of primary importance. The buckling shear of a curved thin plate was determined mathematically and also experimentally. The following formula was obtained mathematically: s=K E t/r in which s is the unit shear, K is a constant, E is the modulus of elasticity, t is the thickness of the material, and r is the radius of curvature. The value of K as determined by the experiments was found to be .075. This formula applies only when s is within the elastic limit of the material. The breaking point of the material was obtained in most of the tests as a matter of information and the results are included in this report. The effect of the supporting ribs was determined by varying the number used.

Smith, George Michael↗

NASA NTRS1925

The Effects of Shielding the Tips of Airfoils

Tests have recently been made at Langley Memorial Aeronautical Laboratory to ascertain whether the aerodynamic characteristics of an airfoil might be substantially improved by imposing certain limitations upon the air flow about its tips. All of the modified forms were slightly inferior to the plain airfoil at small lift coefficients: however, by mounting thin plates, in planes perpendicular to the span, at the wing tips, the characteristics were improved throughout the range above three-tenths of the maximum lift coefficient. With this form of limitation the detrimental effect was slight; at the higher lift coefficients there resulted a considerable reduction of induced drag and consequently, of power required for sustentation. The slope of the curve of lift versus angle of attack was increased.

Reid, Elliott G↗

NASA NTRS1953

Deflection and Stress Analysis of Thin Solid Wings of Arbitrary Plan Form with Particular Reference to Delta Wings

The structural analysis of arbitrary solid cantilever wings by small-deflection thin-plate theory is reduced to the solution of linear ordinary differential equations by the assumption that the chordwise deflections at any spanwise station may be expressed in the form of a power series in which the coefficients are functions of the spanwise coordinate. If the series is limited to the first two and three terms (that is, if linear and parabolic chordwise deflections, respectively, are assumed), the differential equations for the coefficients are solved exactly for uniformly loaded solid delta wings of constant thickness ratio. For cases for which exact solutions to the differential equations cannot be obtained, a numerical procedure is derived. Experimental deflection and stress data for constant-thickness delta-plate specimens of 45 degree and 60 degree sweep are presented and are found to compare favorably with the present theory.

Stein, Manuel↗

NASA NTRS1936

Methods and formulas for calculating the strength of plate and shell constructions as used in airplane design

This report is a compilation of previously published articles on formulas and methods of calculation for the determination of the strength and stability of plate and shell construction as employed in airplane design. In particular, it treats the problem of isotropic, orthotopic, and stiffened rectangular plates, thin curved panels, and circular cylinders under various loading conditions. The purpose of appending the pertinent literature references following the subjects discussed was to facilitate a comprehensive study of the treated problems.

Heck, O S↗

NASA NTRS1994

Counting particles emitted by stratospheric aircraft and measuring size of particles emitted by stratospheric aircraft

The ER-2 condensation nuclei counter (CNC) has been modified to reduce the diffusive losses of particles within the instrument. These changes have been successful in improving the counting efficiency of small particles at low pressures. Two techniques for measuring the size distributions of particles with diameters less than 0.17 micrometers have been evaluated. Both of these methods, the differential mobility analyzer (DMA) and the diffusion battery, have fundamental problems that limit their usefulness for stratospheric applications. We cannot recommend either for this application. Newly developed, alternative methods for measuring small particles include inertial separation with a low-loss critical orifice and thin-plate impactor device. This technique is now used to collect particles in the multisample aerosol collector housed in the ER-2 CNC-2, and shows some promise for particle size measurements when coupled with a CNC as a counting device. The modified focused-cavity aerosol spectrometer (FCAS) can determine the size distribution of particles with ambient diameters as small as about 0.07 micrometers. Data from this instrument indicates the presence of a nuclei mode when CNC-2 indicates high concentrations of particles, but cannot resolve important parameters of the distribution.

Wilson, James Charles↗

NASA NTRS1994

Fatigue crack growth in 2024-T3 aluminum under tensile and transverse shear stresses

The influence of transverse shear stresses on the fatigue crack growth rate in thin 2024-T3 aluminum alloy sheets is investigated experimentally. The tests are performed on double-edge cracked sheets in cyclic tensile and torsional loading. This loading generates crack tip stress intensity factors in the same ratio as the values computed for a crack lying along a lap joint in a pressurized aircraft fuselage. The relevant fracture mechanics of cracks in thin plates along with the details of the geometrically nonlinear finite element analyses used for the test specimen calibration are developed and discussed. Preliminary fatigue crack growth data correlated using the fully coupled stress intensity factor calibration are presented and compared with fatigue crack growth data from pure delta K(sub I)fatigue tests.

Viz, Mark J.↗

NASA NTRS1995

Sensitivity analysis of the non-linear dynamic viscoplastic response of 2-d structures with respect to material parameters

A computational procedure is presented for evaluating the sensitivity coefficients of the viscoplastic response of structures subjected to dynamic loading. A state of plane stress is assumed to exist in the structure, a velocity strain-Cauchy stress formulation is used, and the geometric non-linearities arising from large strains are incorporated. The Jaumann rate is used as a frame indifferent stress rate. The material model is chosen to be isothermal viscoplasticity, and an associated flow rule is used with a von Mises effective stress. The equations of motion emanating from a finite element semi-discretization are integrated using an explicit central difference scheme with an implicit stress update. The sensitivity coefficients are evaluated using a direct differentiation approach. Since the domain of integration is the current configuration, the sensitivity coefficients of the spatial derivatives of the shape functions must be included. Numerical results are presented for a thin plate with a central cutout subjected to an in-plane compressive loading. The sensitivity coefficients are generated by evaluating the derivatives of the response quantities with respect to Young's modulus, and two of the material parameters characterizing the viscoplastic response. Time histories of the response and sensitivity coefficients, and spatial distributions at selected times are presented.

Kulkarni, Makarand↗