Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

A Monte Carlo model for 3D grain evolution during welding

Welding is one of the most wide-spread processes used in metal joining. However, there are currently no open-source software implementations for the simulation of microstructural evolution during a weld pass. Here we describe a Potts Monte Carlo based model implemented in the SPPARKS kinetic Monte Carlo computational framework. The model simulates melting, solidification and solid-state microstructural evolution of material in the fusion and heat-affected zones of a weld. The model does not simulate thermal behavior, but rather utilizes user input parameters to specify weld pool and heat-affect zone properties. Weld pool shapes are specified by Bezier curves, which allow for the specification of a wide range of pool shapes. Pool shapes can range from narrow and deep to wide and shallow representing different fluid flow conditions within the pool. Surrounding temperature gradients are calculated with the aide of a closest point projection algorithm. Furthermore, the model also allows simulation of pulsed power welding through time-dependent variation of the weld pool size. Example simulation results and comparisons with laboratory weld observations demonstrate microstructural variation with weld speed, pool shape, and pulsed-power.

36 MATERIALS SCIENCE↗

Porosity in Millimeter-Scale Welds of Stainless Steel: Three-Dimensional Characterization

A variety of edge joints utilizing a continuous wave Nd:YAG laser have been produced and examined in a 304-L stainless steel to advance fundamental understanding of the linkage between processing and resultant microstructure in high-rate solidification events. Acquisition of three-dimensional reconstructions via micro-computed tomography combined with traditional metallography has allowed for qualitative and quantitative characterization of weld joints in a material system of wide use and broad applicability. The presence, variability and distribution of porosity, has been examined for average values, spatial distributions and morphology and then related back to fundamental processing parameters such as weld speed, weld power and laser focal length.

36 MATERIALS SCIENCE↗

Solidification, growth mechanisms, and associated properties of Al-Si and magnesium lightweight casting alloys

Continually rising energy prices have inspired increased interest in weight reduction in the automotive and aerospace industries, opening the door for the widespread use and development of lightweight structural materials. Chief among these materials are cast Al-Si and magnesium-based alloys. Utilization of Al-Si alloys depends on obtaining a modified fibrous microstructure in lieu of the intrinsic flake structure, a process which is incompletely understood. The local solidification conditions, mechanisms, and tensile properties associated with the flake to fiber growth mode transition in Al-Si eutectic alloys are investigated here using bridgman type gradient-zone directional solidification. Resulting microstructures are examined through quantitative image analysis of two-dimensional sections and observation of deep-etched sections showing three-dimensional microstructural features. The transition was found to occur in two stages: an initial stage dominated by in-plane plate breakup and rod formation within the plane of the plate, and a second stage where the onset of out-of-plane silicon rod growth leads to the formation of an irregular fibrous structure. Several microstructural parameters were investigated in an attempt to quantify this transition, and it was found that the particle aspect ratio is effective in objectively identifying the onset and completion velocity of the flake to fiber transition. The appearance of intricate out-of-plane silicon instability formations was investigated by adapting a perturbed-interface stability analysis to the Al-Si system. Measurements of silicon equilibrium shape particles provided an estimate of the anisotropy of the solid Si/liquid Al-Si system and incorporation of this silicon anisotropy into the model was found to improve prediction of the instability length scale. Magnesium alloys share many of the benefits of Al-Si alloys, with the added benefit of a 1/3 lower density and increased machinability. Magnesium castings often contain additions of heavier elements, such as zinc, zirconium, and rare earth elements, which significantly improve high temperature performance. However, additions of these elements can lead to macrosegregational effects in castings, which are detectable by radiographic scans. The effect of these flow-line indications on alloy mechanical properties is not well quantified. An examination of these flow-line indications and their effects on mechanical properties in three magnesium-based casting alloys was performed here in order to determine the best practice for dealing with affected castings. Preliminary results suggest the flow-lines do not measurably impact bulk material properties. Three additional methods of characterizing three-dimensional material structures are also presented: a minimum spanning tree analysis is utilized to quantify local structure in Cu-Zr liquid phase simulations obtained from molecular dynamics; the radial distribution function is applied to directionally solidified Al-Si structures in an attempt to extract local spacing data; and the critical diameter measurement is also defined and applied to irregular eutectic Al-Si structures.

36 MATERIALS SCIENCE↗

EBSD characterization of the eutectic microstructure in hypoeutectic Fe-C and Fe-C-Si alloys

Highlights: • EBSD investigation of eutectic cementite and austenite in as-solidified low-alloy cast iron • Crystallographically independent growth of rapidly solidified cementite/austenite eutectic • Epitaxial growth of eutectic austenite from primary dendrites • Eutectic cementite and eutectoid ferrite frequently obey Bagaryatsky or Pitsch-Petch orientation relationship. - Abstract: Hypoeutectic Fe-C and Fe-C-Si model alloys were produced at different solidification conditions. Copper mold casting yields low cooling rates promoting the formation of a eutectic microstructure, which is characterized by two morphologies: elongated cementite plates and a rod structure growing perpendicular to the plates, i.e. austenite rods in a cementite matrix. Electron beam surface remelting generates a mainly plate-like eutectic due to rapid solidification. The microstructures were characterized by light-optical microscopy and electron backscatter diffraction (EBSD). The latter allows for a spatially resolved investigation of the growth crystallography of the eutectic phases. Thereby, a possible existence of crystallographic orientations relationships between cementite and austenite within the plate-like eutectic was assessed experimentally. The eutectic phases were found to grow largely crystallographically independently. Moreover, ferrite and eutectic cementite within the decomposed eutectic microstructure frequently comply with the Bagaryatsky or the Pitsch-Petch orientation relationship. Complementary X-ray diffraction (XRD) analysis reveals a pronounced cementite {002} texture in the microstructure produced by mold casting. Characteristic changes in the lattice parameters indicate that as-cast cementite is non-stoichiometric.

36 MATERIALS SCIENCE↗

Study of the Printability, Microstructures, and Mechanical Performances of Laser Powder Bed Fusion Built Haynes 230

The nickel-based superalloy, Haynes 230 (H230), is widely used in high-temperature applications, e.g., heat exchangers, because of its excellent high-temperature mechanical properties and corrosion resistance. As of today, H230 is not yet in common use for 3D printing, i.e., metal additive manufacturing (AM), primarily because of its hot cracking tendency under fast solidification. The ability to additively fabricate components in H230 attracts many applications that require the additional advantages leveraged by adopting AM, e.g., higher design complexity and faster prototyping. In this study, we fabricated nearly fully dense H230 in a laser powder bed fusion (L-PBF) process through parameter optimization. The efforts revealed the optimal process space which could guide future fabrication of H230 in various metal powder bed fusion processes. The metallurgical analysis identified the cracking problem, which was resolved by increasing the pre-heat temperature from 80 °C to 200 °C. A finite element simulation suggested that the pre-heat temperature has limited impacts on the maximum stress experienced by each location during solidification. Additionally, the crack morphology and the microstructural features imply that solidification and liquation cracking are the more probable mechanisms. Both the room temperature tensile test and the creep tests under two conditions, (a) 760 °C and 100 MPa and (b) 816 °C and 121 MPa, confirmed that the AM H230 has properties comparable to its wrought counterpart. The fractography showed that the heat treatment (anneal at 1200 °C for 2 h, followed by water quench) balances the strength and the ductility, while the printing defects did not appreciably accelerate part failure.

14 SOLAR ENERGY↗

Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V

Selective laser melting (SLM) process is characterized by large temperature gradients resulting in high levels of residual stress within the additively manufactured metallic structure. SLM-processed Ti6Al4V yields a martensitic microstructure due to the rapid solidification and results in a ductility generally lower than a hot working equivalent. Post-process heat treatments can be applied to SLM components to remove in-built residual stress and improve ductility. Residual stress buildup and the mechanical properties of SLM parts can be controlled by varying the SLM process parameters. This investigation studies the effect of layer thickness on residual stress and mechanical properties of SLM Ti6Al4V parts. This is the first-of-its kind study on the effect of varying power and exposure in conjunction with keeping the energy density constant on residual stress and mechanical properties of SLM Ti6Al4V components. It was found that decreasing power and increasing exposure for the same energy density lowered the residual stress and improved the % elongation of SLM Ti6Al4V parts. Increasing layer thickness resulted in lowering the residual stress at the detriment of mechanical properties. The study is based on detailed experimental analysis along with finite element simulation of the process using ABAQUS to understand the underlying physics of the process.

36 MATERIALS SCIENCE↗

Rapid Solidification of Sn-Cu-Al Alloys for High-Reliability, Lead-Free Solder: Part I. Microstructural Characterization of Rapidly Solidified Solders

Particles of Cu x Al y in Sn-Cu-Al solders have previously been shown to nucleate the Cu 6 Sn 5 phase during solidification. In this study, the number and size of Cu 6 Sn 5 nucleation sites were controlled through the particle size refinement of Cu x Al y via rapid solidification processing and controlled cooling in a differential scanning calorimeter. Cooling rates spanning eight orders of magnitude were used to refine the average Cu x Al y and Cu 6 Sn 5 particle sizes down to submicron ranges. The average particle sizes, particle size distributions, and morphologies in the microstructures were analyzed as a function of alloy composition and cooling rate. Deep etching of the samples revealed the three-dimensional microstructures and illuminated the epitaxial and morphological relationships between the Cu x Al y and Cu 6 Sn 5 phases. Transitions in the Cu 6 Sn 5 particle morphologies from faceted rods to nonfaceted, equiaxed particles were observed as a function of both cooling rate and composition. Initial solidification cooling rates within the range of 10 3 to 10 4 °C/s were found to be optimal for realizing particle size refinement and maintaining the Cu x Al y /Cu 6 Sn 5 nucleant relationship. In addition, little evidence of the formation or decomposition of the ternary-β phase in the solidified alloys was noted. As a result, solidification pathways omitting the formation of the ternary-β phase agreed well with observed room temperature microstructures.

36 MATERIALS SCIENCE↗

Reactive gas atomization processing for Fe-based ODS alloys

Gas atomization reaction synthesis was employed as a simplified method for processing oxide dispersion forming precursor Fe-based powders (e.g., Fe–Cr–Y–Hf). During this process a reactive atomization gas (i.e., Ar–O2) was used to oxidize the powder surfaces during primary break-up and rapid solidification of the molten alloy. This resulted in envelopment of the powders by an ultra-thin (t < 50 nm) metastable Cr-enriched oxide shell that was used as a vehicle to transport oxygen into the consolidated microstructure. Subsequent elevated temperature heat treatment promoted thermodynamically driven oxygen exchange reactions between trapped films of Cr-enriched oxide and internal (Y, Hf)-enriched intermetallic precipitates, resulting in highly stable nano-metric mixed oxide dispersoids (i.e., Y–Hf–O) that were identified with X-ray diffraction. Transmission electron microscopy and atom probe tomography results also revealed that the size and distribution of the dispersoids were found to depend strongly on the original rapidly solidified microstructure. To exploit this, several oxide dispersion strengthened microstructures were engineered from different powder particle size ranges, illustrating microstructural control as a function of particle solidification rate. Additionally, preliminary thermal–mechanical processing was used to develop a fine scale dislocation substructure for ultimate strengthening of the alloy.

36 MATERIALS SCIENCE↗

Three-dimensional dendritic needle network model for alloy solidification

Here, we present a three-dimensional (3D) formulation of the multiscale Dendritic Needle Network (DNN) model for dendritic microstructure growth. This approach is aimed at simulating quantitatively the solidification dynamics of complex hierarchical networks in spatially extended dendritic arrays, hence bridging the scale gap between phase-field simulations at the scale of a few dendrites and coarse-grained simulations on the larger scale of entire polycrystalline structures. In the DNN model, the dendritic network is represented by a network of branches that interact through the solutal diffusion field. The tip velocity V(t) and tip radius ρ(t) of each needle is determined by combining a standard solvability condition that fixes the product ρ 2 V and a solute flux conservation condition that fixes the product ρV 2 in 2D and ρV in 3D as a function of a solutal flux intensity factor ℱ(t). The latter measures the intensity of the solute flux in the dendrite tip region and can be calculated by contour (2D) or surface (3D) integration around the tip of each needle. We first present an extended formulation of the 2D DNN model where needles have a finite thickness and parabolic tips. This formulation remains valid for a larger range of tip Péclet number than the original thin needle formulation and is readily extended to 3D needles with paraboloidal tips. The 3D DNN model based on this thick-needle formulation is developed for both isothermal and directional solidification. Model predictions are validated by comparisons with known analytical solutions that describe the early transient and steady-state growth regimes. We exploit the power of the DNN model to characterize the competitive growth of well-developed secondary branches in 3D on the scale of the diffusion length. The results show that the length of active secondary branches increases as a power law of distance behind the tip with an exponent in good quantitative agreement with experimental measurements. Finally, we apply the model to simulate the three-dimensional directional solidification of an Al-7wt% Si alloy, which we directly compare to observed microstructures from microgravity experiments onboard the International Space Station. The predictions of selected microstructural features, such as dendrite arm spacings, show a good agreement with experiments. The computationally-efficient DNN model opens new avenues for investigating the dynamics of large dendritic arrays at length and time scales relevant to solidification experiments and processes.

36 MATERIALS SCIENCE↗

Simulated Microstructures for Laser Powder Bed Fusion Additive Manufacturing Using Myna, AdditiveFOAM, and ExaCA

This dataset provides sample datasets containing voxelized, three-dimensional representations of simulated grain structures and crystallographic orientations that can result from laser powder bed fusion additive manufacturing. The six microstructure files each contain approximately 1 cubic millimeter of material (1 mm x 1 mm cross-section over 26 simulated layers of deposition). Some of the microstructures have columnar grains that extend across nearly the entire simulation domain, while others have more equiaxed or truncated columnar grains. The process conditions to generate these microstructures were from the Peregrine v2023-10 dataset (10.13139/ORNLNCCS/2008021). The codes used are publicly available and released under open-source licenses. Myna (https://github.com/ORNL-MDF/Myna) was used for configuration of the cases from the Peregrine v2023-10 HDF5 dataset and to run the simulation workflow. AdditiveFOAM (https://github.com/ORNL/AdditiveFOAM) was used to simulate the melt pool and generate solidification conditions. And ExaCA (https://github.com/LLNL/ExaCA ) was used to simulate the three-dimensional microstructures.

36 MATERIALS SCIENCE↗

Effect of Cooling Rate on Nano-Eutectic Formation in Laser Surface Remelted and Rare Earth Modified Hypereutectic Al-20Si Alloys

Laser Surface Remelting (LSR) was applied to arc-melted Al-20Si-0.2Sr, Al-20Si-0.2Ce, and Al-20Si hypereutectic alloys to refine microstructures. Experiments revealed that microstructures in the melt pool varied from fully eutectic to a mixture of Al dendrites and inter-dendritic eutectic. We calculated cooling rates using the Eagar-Tsai model and correlated cooling rates with characteristic microstructures, revealing that a cooling rate on the order of 104 K/s could lead to maximized fully eutectic microstructure morphology. Due to rapid solidification, the Si composition in the LSR eutectic was measured at 18.2 wt.%, higher than the equilibrium eutectic composition of 12.6 wt.%Si. Compared to Al-20Si, Ce addition had no significant effect on the volume fraction of the fully eutectic structure but refined Si fibers to approximately 30 nm in diameter. Sr addition did not further refine the diameter of eutectic Si fibers compared to Al-20Si but increased the volume fraction of the fully eutectic microstructure morphology. The refinement ratio (φ) of the Si fiber diameter from the bottom of the melt pool to the surface for the three alloys was similar, at around 28%. The established correlation between the cooling rate and the size and morphology of the microstructure within the melt pool will enable tailoring of the microstructure in laser-processed as well as deposited alloys for high strength and plasticity.

36 MATERIALS SCIENCE↗

Fatigue and Fracture Behavior of Additively Manufactured Austenitic Stainless Steel

Additive manufacturing (AM) includes a diverse suite of innovative manufacturing processes for producing near-net shape components, typically from powder or wire feedstock. Reported mechanical properties of AM materials vary significantly depending on the details of the manufacturing process and the characteristics of the processing defects (namely, lack of fusion defects). However, an excellent combination of strength, ductility and fracture resistance can be achieved in AM type 304L and 316L austenitic stainless steels by minimizing processing defects. It is also important to recognize that localized solidification processing during AIVI produces microstructures more analogous to weld microstructures than wrought microstructures. Consequently, the mechanical behavior of AM austenitic stainless steels in harsh environments can diverge from the performance of wrought materials. This report gives an overview of the fracture and fatigue response of type 304L materials from both directed energy deposition (DED) and powder bed fusion (PBF) techniques. In particular, the mechanical performance of these materials is considered for high-pressure hydrogen applications by evaluating fatigue and fracture resistance after thermally precharging of test specimens in high-pressure gaseous hydrogen. The mechanical behaviors are considered with respect to previous reports on hydrogen-assisted fracture of austenitic stainless steel welds and the unique characteristics of the AM microstructures. Fatigue crack growth can be relatively insensitive to processing defects, displaying similar behavior as wrought materials. Fracture resistance of dense AM austenitic stainless steel, on the other hand, is more consistent with weld metal than with compositionally-similar wrought materials. Hydrogen effects in the AM materials are generally more severe than in wrought materials, but comparable to measurements on welded austenitic stainless steels in hydrogen environments. While hydrogenassisted fracture manifests differently in welded and AM austenitic stainless steel, the fracture process appears to have a common origin in the compositional microsegregation intrinsic to solidification processes.

additive manufacturing, austenitic stainless steel↗

Interfacial characterization of SLM parts in multi-material processing: Metallurgical diffusion between 316L stainless steel and C18400 copper alloy

Multi-material processing in selective laser melting using a novel approach, by the separation of two different materials within a single dispensing coating system was investigated. 316L stainless steel and UNS C18400 Cu alloy multi-material samples were produced using selective laser melting and their interfacial characteristics were analyzed using focused ion beam, scanning electron microscopy, energy dispersive spectroscopy and electron back scattered diffraction techniques. A substantial amount of Fe and Cu element diffusion was observed at the bond interface suggesting good metallurgical bonding. Quantitative evidence of good bonding at the interface was also obtained from the tensile tests where the fracture was initiated at the copper region. Nevertheless, the tensile strength of steel/Cu SLM parts was evaluated to be 310 ± 18 MPa and the variation in microhardness values was found to be gradual along the bonding interface from the steel region (256 ± 7 HV{sub 0.1}) to the copper region (72 ± 3 HV{sub 0.1}). - Highlights: • Multi-material processing was successfully implemented and demonstrated in SLM. • Bi-metallic laminates of steel/Cu were successfully produced with the SLM process. • A substantial amount of Fe and Cu diffusion was observed at the bond interface. • Good metallurgical bonding was obtained at the interface of the steel/Cu laminates. • Highly refined microstructure was obtained due to rapid solidification in SLM.

36 MATERIALS SCIENCE↗

Multiscale and Machine Learning Modeling for Process-informed Microstructure Prediction in Additively Manufactured Materials using MALAMUTE

The Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy aims to develop and qualify additively manufactured materials for nuclear applications. One key challenge to this is the microstructural variability observed in the additively manufactured products and their impact on the properties and performance of the material in extreme environments. AMMT is using a combination of high-throughput experimental and modeling techniques to accelerate qualification. Conventionally, in-situ and ex-situ characterizations and testing are performed to correlate different aspects of the additive manufacturing process to the final product and its performance. However, adopting a trial-and-error approach to experimentally evaluate the vast range of process parameters required to capture microstructural variability is cost-prohibitive. Modeling and simulation provide a comparatively inexpensive way to understand and correlate the microstructural evolution to the processing conditions. The modeling and simulation work-packages within the AMMT program aims to use physics-based and machine learning models to develop a digital twin for additive manufacturing that can correlate the process conditions to the final product and establish a process-structure-property-performance (PSPP) correlation. The melting and subsequent solidification that occurs during the additive process is a complex phenomenon that requires multiscale multiphysics analysis. This work package focuses on understanding the role of process variabilities on the unique microstructural characteristics of additively manufactured materials. Microstructural features at the subgrain level, such as compositional micro-heterogeneity and dislocation cells, are of particular interest here since they can influence the creep properties and radiation performance. Idaho National Laboratory’s Multiphysics Object-Oriented Simulation Environment (MOOSE), specifically the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) software, provides an ideal platform for developing the multiphysics multiscale model to explore the intricacies of the microstructural evolution during the AM processes within a single framework. Furthermore, given that such full-fidelity simulations can be computationally intensive, reduced order models are necessary to explore the PSPP space for additively manufactured materials in an efficient, reliable, and cost-effective way. This work focuses on capturing the microstructural variabilities at the subgrain level that are often missing in the part-scale models. In fiscal year 2025, we significantly advanced upon our work in the last fiscal year, in terms of the predictive capabilities of the physics-based and ML models, by adding the capabilities to capture subgrain-level micro-segregation during solidification using phase-field model and to predict the time-dependent dynamics of the AM process through the MOGPAR model. The alloy solidification model in MOOSE incorporates the thermodynamic properties and free energy relevant to 316 stainless steel. The model demonstrates the Cr and Ni segregation that occurs during solidification, including that the rate of solidification. The microstructural evolution model is connected to the process conditions via the surrogate model developed in this work. This enables predictions of the final microstructure in conjunctions with the manufacturing process. This work supports AMMT's rapid qualification goals by laying the foundation for an efficient and cost-effective model establishing the PSPP correlation for AM. The generated microstructures and predicted micro-segregation can be used by other work packages under AMMT to evaluate the properties and environmental response of the material at the mesoscale. Thus, this work helps to identify the key microstructural features at the subgrain level that are significant in property and performance predictions of additively manufactured components. This work will also provide inputs to the large-scale process variability models to reevaluate and validate assumptions and simplifications made in the part-scale models. Furthermore, through active learning this work can help identify the data need from both modeling and experimental sides for development of a robust digital twin for additive manufacturing and accelerate the AMMT's qualification efforts.

36 - MATERIALS SCIENCE↗

Rapid Solidification Effects in Additively Manufactured Si and SiGe Compositions

SiGe alloys have a proven track record as robust high-temperature thermoelectric materials, powering NASA missions like SNAP-10A, LES-9, and Voyager 1 and 2. Enhancing thermoelectric efficiency hinges on minimizing thermal conductivity while preserving electrical conductivity. Rapid solidification via LPBF can generate microstructural features such as subgrain cellular boundaries and twinning, which may help reduce thermal conductivity while preserving semiconducting behavior. Here, this study investigates the potential of laser powder bed fusion (LPBF) additive manufacturing to fabricate nanostructured Si and SiGe thermoelectric materials. High cooling rates (10 5 to 10 7 K/s) rates inherent to the LPBF process are conducive to forming such nanostructures. Moreover, this fabrication technique could also be suitable for fabricating complex geometries needed to achieve improved device level performance. Process mapping of commercial Si powder with irregular morphology was first performed to understand the LPBF processing behavior of this semiconductor material. Subsequent studies included in-house synthesized B-doped (p-type) Si7 8 Ge 22 spherical powder that was produced via ultrasonic atomization. Scan strategies involved multiple laser exposures to mitigate solidification cracking: a high density of >98% was achieved, but solidification cracking could not be fully eliminated. Subsequently, a high electrical resistivity (i.e., low conductivity) was observed, but the measured Seebeck coefficient, ∼230 μV/K @ 500 °C, proved that good semiconductor material was being fabricated. A subgrain cellular structure (5–10 μm) was observed as defined by Ge segregation to the intercellular boundaries. The remelting strategies helped lower the cooling rates in processing SiGe, but this still resulted in high residual stresses, which induced a remarkably high density of twins (78–95%) to accommodate the deformation. This unique grain structure offers an avenue for phonon scattering and potential improvements in thermoelectric performance.

figure of merit↗

Solid Phase Gradient Alloying Method via ShAPE

Alloying has been used to confer desirable properties to various metallic systems since the bronze age. For example, Ni, Mn, and Cr are alloyed into an Fe matrix to make steel, which has improved strength and corrosion resistance (as displayed in Fig. 1). In addition to the type of alloying elements, the amount of alloying elements added into a matrix is also very critical for a material’s mechanical property, physical property, machinability, and cost. Conventionally, new alloys are discovered by combining alloy precursors and elemental constituents into a mixture and melting them together. The solidified product or ingot represents a usually non-homogeneous combination of the chemistry with a microstructure dictated by the physics of solidification. It is time and energy intensive to optimize the alloying amounts via the casting process and hence, economically not conducive to rapid alloy discovery. In addition, the cast microstructure seen in the as-cast ingot is often not the ideal, nor even desired structure for optimized performance. Cast materials often need further processing such as homogenization, annealing, and deformation work put in through rolling, forging, extruding, etc. to have favorable microstructures and properties. A faster method to discover new alloy combinations and evaluate them in their worked or processed form is needed. Recently, Laser Engineered Net Shaping was applied to fabricate gradient compositional material for alloy designing. However, the mechanical properties of this gradient alloy were poor due to the existence of impurities, oxidation and cracks that are inherent in the melt-solidification process. Because of these limitations, we propose to use a solid-phase process (ShAPE) to create bulk materials (extrudates) that vary in composition from one end of the extruded solid to the other. Various manufacturing methods for alloy design including conventional casting method, laser based combinatorial method and current solid phase gradient alloying method are displayed and compared in Fig. 2. ShAPE machine and a schematic of ShAPE process are displayed in Fig. 3. Starting material is processed by a rotating and plunging die to form an extrudate. We are proposing through this methodology to invent a new, bulk-scale combinatorial technique. With this novel technique, alloying element can be dissolved into the matrix with a continued gradient without bulk melting. Formation of inter-metallics and defects originating from melt processing can be avoided. In addition, the ShAPE process creates the mixed alloy chemistry, and meanwhile subjects the material to severe plastic strain, which induces the favorable “worked” microstructure. Products from the ShAPE process can be tested in hardness directly providing a path to rapid evaluation of mechanical properties. The ability to create graded structures using friction stir processing (FSP) has been demonstrated, however using the ShAPE process we believe will lead to much faster and higher fidelity results. When combined with high throughput screening methods of physical, mechanical and microstructural property characterization, efficiency and accuracy of alloy design can be significantly improved.

36 MATERIALS SCIENCE↗

Synergy of tensile strength and high cycle fatigue properties in a novel additively manufactured Al-Ni-Ti-Zr alloy with a heterogeneous microstructure

Alloy design strategies in additive manufacturing (AM) to achieve grain refinement and terminal eutectic solidification have been introduced to engineer Al alloys having microstructural hierarchy and heterogeneity. Such alloy design strategies enable crack-free builds with an expanded AM processing window and pushed the strength limit in Al alloys. However, fatigue performance of Al alloys made by AM is restricted by the presence of process induced defects and its stochasticity. In this work, tensile and high cycle fatigue (HCF) behavior of a novel Al-Ni-Ti-Zr alloy with a heterogeneous microstructure is studied in the as-built condition, supplemented by detailed microstructural and mechanical characterization. Excellent strength-ductility synergy of 342 MPa and 16% failure strain achieved in the alloy was associated with the microstructural attributes that pertain to the novel alloy. Additionally, the alloy showed excellent HCF performance with a fatigue endurance limit to ultimate tensile strength ratio of 0.29 in flexural fatigue mode. The study revealed the existence of multiple crack retardation mechanisms and favorable crack propagation pathways through the fine-grained regions which enabled good fatigue performance to the alloy. Further, a probabilistic model has been used to estimate the fatigue life of the alloy as a function of the stochastic microstructure by utilizing the statistical distribution of pores, solid-state inclusions, and grains in the AM Al alloy. Finally, the model parametric trends are consistent with the experimental observations.

36 MATERIALS SCIENCE↗

Which way does the dendrite grow? Competition among epitaxy, preferred growth direction, and thermal gradients in powder bed fusion additive manufacturing

The as-processed microstructure of metal alloy parts manufactured through laser powder bed fusion (LPBF) is heavily derived from the cellular dendritic solidification. The growth direction of dendrites within the melt pool is determined through competition among epitaxial growth, preferred growth directions, and maximum thermal gradients. However, the dominant factor and the specific role of each in developing melt pool microstructures remain unknown. Here, in this study, we performed single laser track scans on an SS316L single crystal substrate and combined experimental characterization of microstructure and crystal orientations with Computational Fluid Dynamics simulations of thermal gradients to evaluate the role of each factor in determining dendritic growth direction and evolution. Our results reveal that epitaxial growth dominates microstructure development by preferentially growing along a single 〈100〉 variant of the single crystal substrate adjacent to the melt pool boundary. Under LPBF’s highly curved and rapidly evolving thermal field, this preferential dendrite variant selection and its continued growth from the melt pool boundary to the centerline are governed by the local temperature gradient magnitude at the solid-liquid interface, rather than by the instantaneous maximum temperature gradient direction alone. Using these findings, we successfully predict changes in the dendrite growth direction with changing laser scan direction on a single crystal substrate, and show that the geometric melt pool centerline can deviate from the microstructural centerline because asymmetric local temperature gradient magnitudes transiently limit growth, resulting in different dendrite travel distances on each side of the melt pool.

36 MATERIALS SCIENCE↗