Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solid solution alloys”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Influence of fine-scale B2 precipitation on dynamic compression and wear properties in hypo-eutectic Al0.5CoCrFeNi high-entropy alloy

The near equiatomic high-entropy alloys based on Al, Co, Cr, Fe, Ni have provided a novel microstructural template for alloy design. The face-centered cubic (FCC) matrix strengthened by body-centered cubic (BCC) based ordered B2 precipitates can be used to develop a new generation of precipitation strengthened alloys. The present study focuses on an Al0.5CoCrFeNi hypo-eutectic alloy consisting of an as-solidified FCC+B2 microstructure. Guided by solution thermodynamic modeling, this alloy has been isothermally aged for solid-state precipitation of a high fraction of fine-scale intragranular B2 particles. The dynamic compressive strength, hardness, and sliding wear response of the alloy as a function of B2 phase fraction is examined. The flow stress at 0.02% true strain increased from ~ 670 MPa to ~1350 (102%) MPa, the ultimate compressive strength increased from ~1160 MPa to 1500 MPa (20%), and the wear resistance increased more than 5 times with progressively increasing phase fraction of B2 precipitates.

Gwalani, Bharat↗
DOE OSTI2020

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Compared to the widely used Fe-3.2wt%Si steel, Fe-6.5wt%Si has superior electric and magnetic properties, including higher electrical resistivity, lower iron loss, higher permeability, and near zero magnetostriction. However, Fe-6.5wt%Si sheet is difficult to produce using traditional manufacturing processes as the high silicon content favors the formation of ordered phases that embrittle the material. Fortunately, these ordered phases can be suppressed if the alloy is cooled fast enough from a high temperature kinetically trapping the disordered solid solution or amorphous state. Planar flow casting is known for its rapid solidification rate. In order to consider it as a viable method to manufacture ductile Fe-6.5wt%Si sheets, the effect of cooling rate on physical properties of Fe-6.5wt%Si alloy are systematically investigated. In this work, various cooling rates are achieved by changing melt-spin wheel speeds, which significantly affect the solidification temperature profile and have profound effects on ordering, microstructures, textures, hardness, and magnetic properties. High cooling rates result in refined grains, reduced ordering, enhanced <100> out of the plane texture, decreased hardness, and increased coercivity. This study demonstrates a critical cooling rate at ~1.7 × 10 5 K/s, corresponding to a tangential wheel speed of 5-7 m/s, below which the hardness significantly increases in agreement with the sudden increase of the ordered phases that causes the material embrittlement.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Line tension induced character angle dependence of dislocation mobility in FCC alloys

Here, we explore the character angle dependence of dislocation-solute interactions in a face-centered cubic random Fe0.70Ni0.11Cr0.19 alloy through molecular dynamics (MD) simulations of dislocation mobility. Using the MD mobility data, we determine the phonon and thermally activated solute drag parameters which govern mobility for each dislocation character angle. The resulting parameter set indicates that, surprisingly, the solute energy barrier does not depend on character angle. Instead, only the zero-temperature flow stress—which is dictated by the activation area for thermal activation—is dependent on character angle. By analyzing the line roughness from MD simulations and the geometry of a bowing dislocation line undergoing thermal activation, we conclude that the character angle dependence of the activation area in this alloy is governed by the dislocation line tension, rather than the dislocation-solute interaction itself. Our findings motivate further investigation into the line geometry of dislocations in solid solutions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High Thermoelectric Performance in the New Cubic Semiconductor AgSnSbSe 3 by High-Entropy Engineering

We investigate the structural and physical properties of the AgSn m SbSe m+2 system with m = 1-20 (i.e., SnSe matrix and ~5-50% AgSbSe 2 ) from atomic, nano, and macro length scales. We find the 50:50 composition, with m = 1 (i.e., AgSnSbSe 3 ), forms a stable cation-disordered cubic rock-salt p-type semiconductor with a special multi-peak electronic valence band structure. AgSnSbSe 3 has an intrinsically low lattice thermal conductivity of ~0.47 W m -1 K -1 at 673 K owing to the synergy of cation disorder, phonon anharmonicity, low phonon velocity, and low-frequency optical modes. Furthermore, Te alloying on Se sites creates a quinary high-entropy NaCl-type solid solution AgSnSbSe 3-x Te x with randomly disordered cations and anions. The extra point defects and lattice dislocations lead to glass-like lattice thermal conductivities of ~0.32 W m -1 K -1 at 723 K and higher hole carrier concentration than AgSnSbSe 3 . Concurrently, the Te alloying promotes greater convergence of the multiple valence band maxima in AgSnSbSe 1.5 Te 1.5 , the composition with the highest configurational entropy. Facilitated by these favorable modifications, we achieve a high average power factor of ~9.54 μW cm -1 K -2 (400-773 K), a peak thermoelectric figure of merit ZT of 1.14 at 723 K, and a high average ZT of ~1.0 over a wide temperature range of 400-773 K in AgSnSbSe 1.5 Te 1.5 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Extreme Fermi Surface Smearing in a Maximally Disordered Concentrated Solid Solution

We show that the Fermi surface can survive the presence of extreme compositional disorder in the equiatomic alloy Ni 0.25 Fe 0.25 Co 0.25 Cr 0.25 . Our high-resolution Compton scattering experiments reveal a Fermi surface which is smeared across a significant fraction of the Brillouin zone (up to 40% of $\frac{2π}{a}$). The extent of this smearing and its variation on and between different sheets of the Fermi surface have been determined, and estimates of the electron mean free path and residual resistivity have been made by connecting this smearing with the coherence length of the quasiparticle states.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Edge dislocation mediated anomalous charge transfer in face centered cubic high entropy alloys

The charge transfer in alloys dictates their structural and functional properties. The presence of the line defect can influence the charge transfer characteristics in alloys. The edge dislocation-volume misfit interaction in high entropy alloys is a critical area of interest concerning the development of accurate solid solution strengthening models for these materials. The evolution of the volume misfit of atoms is either studied empirically using Vegard's law or mechanistically using \emph{ab initio} calculations, without considering the effect of edge dislocation on charge transfer explicitly. In this work, we show the influence of edge dislocation on the charge transfer in CoCrFeMnNi, CoCrNi and CoNi using large-scale \emph{ab initio} calculations. The anomalous charge transfer characteristics, in terms of deviations from electronegativity trends, are demonstrated, which are dictated by electronegativity equalisation rather than pair-atom interactions. The deviation of atomic volume in the compressive and tensile stress regions of the edge dislocation is rationalised in terms of anomalous magneto-volume fluctuations in such alloys.

Ghosh, Swarnava [ORNL] (ORCID:0000000338005264)↗
DOE OSTI2020

Laser metal deposition of refractory high-entropy alloys for high-throughput synthesis and structure-property characterization

Progress in materials development is often paced by the time required to produce and evaluate a large number of alloys with different chemical compositions. This applies especially to refractory high-entropy alloys (RHEAs), which are difficult to synthesize and process by conventional methods. To evaluate a possible way to accelerate the process, high-throughput laser metal deposition was used in this work to prepare a quinary RHEA, TiZrNbHfTa, as well as its quaternary and ternary subsystems by in-situ alloying of elemental powders. Compositionally graded variants of the quinary RHEA were also analyzed. Our results show that the influence of various parameters such as powder shape and purity, alloy composition, and especially the solidification range, on the processability, microstructure, porosity, and mechanical properties can be investigated rapidly. The strength of these alloys was mainly affected by the oxygen and nitrogen contents of the starting powders, while substitutional solid solution strengthening played a minor role.

additive manufacturing↗
DOE OSTI2021

Analytic Binary Alloy Volume–Concentration Relations and the Deviation from Zen’s Law

Alloys expand or contract as concentrations change, and the resulting relationship between atomic volume and alloy content is an important property of the solid. While a well-known approximation posits that the atomic volume varies linearly with concentration (Zen’s law), the actual variation is more complicated. Here we use the apparent size of the solute (solvent) atom and the elasticity to derive explicit analytical expressions for the atomic volume of binary solid alloys. Two approximations, continuum and terminal, are proposed. Deviations from Zen’s law are studied for 22 binary alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Short-range order and longer-range disorder revealed in germanium–tin alloy thin films by extended x-ray absorption fine structure analysis

Short-range order (SRO) in semiconductor alloys, a relatively under-studied structural phenomenon in which local atomic arrangements differ from those of a random solid solution, is investigated in molecular beam epitaxy (MBE)-grown GeSn thin films. A novel preparation technique is used to pattern these films into microscale ribbons that are released from the substrate for extended x-ray absorption fine structure (EXAFS) analysis. The results indicate a strong SRO in which the first shell around Sn atoms is greatly denuded of Sn atoms relative to the nominal atomic composition of the alloy. This effect is more pronounced than that observed recently in GeSn nanowires grown by chemical vapor deposition. Additionally, the presence of a longer-range disorder detected by EXAFS analysis in the shells of atoms more distant from the absorbers is indicative of the defects and inhomogeneous strain present in the MBE-grown films. The evident existence of the SRO in GeSn alloys deposited by different growth methods and in different strain states suggests that SRO is a general phenomenon in the thin films of this metastable solid solution.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Universal Maximum Strength of Solid Metals and Alloys

As described here, interstitial electron density ρ o is offered as a direct metric for maximum strength in metals, arising from universal properties derived from an electron-gas – ρ o sets the exchange-correlation parameter r s in density-functional theory (DFT). It holds also for maximum shear strength τ max in polycrystals [Phys. Rev. Lett. 124, 125501]. Elastic moduli and τ max for polycrystalline (amorphous) metals are linear with ρ o and melting T m (glass-transition T g ) temperature. ρ o or r s , even with rule-of-mixture estimate, predicts relative strength for rapid, reliable selection of high-strength alloys with ductility, as confirmed for elements to steels to complex solid-solutions, and validated experimentally.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Crystallographic ordering of Al and Sn in α-Ti

Increasing attention is being paid to α (2) Ti 3 (Al,Sn) precipitation from the α phase of titanium alloys owing to its effect on slip band formation, localisation and the implications for fatigue performance in jet engine titanium. However, the early stages of α 2 precipitation have historically been difficult to observe by electron microscopy, neutron diffraction or atom probe analysis. Here, small angle X-ray scattering is used to reexamine the phase boundary in binary Ti-Al and Ti-Sn alloys with around 500 ppmw O. It is found that the phase boundaries in the literature are approximately correct, at 6.2 wt.% Al and 16.9 wt.% Sn, and that this favours the use of Al as a solid solution strengthener over Sn for ambient temperature applications. However, once O content and phase partitioning in α + β alloys are taken into account, this implies that Al eq limits for future alloy design of critical rotating parts should be lowered substantially.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructure and mechanical behavior of a TiC nanoprecipitate strengthened V Alloy

The V-4Cr-4Ti (V44) alloys have been proposed as the prime candidate structural material for self-cooled liquid Li blanket and other designs for fusion energy applications. However, the applications of the V44 alloy are limited to a narrow operation temperature window, due to reduction in creep strength at or above 700 °C and susceptibility to irradiation hardening and embrittlement when irradiated below 400 °C. Here, in this work, we explore the feasibility of designing a novel V alloy to form a high number density of TiC nanoprecipitates, in order to simultaneously improve creep strength and provide defect sinks to mitigate irradiation hardening. Computational thermodynamics was used to design a new alloy (V44C) to achieve our goal of high TiC nanoprecipitates density within the alloy V44 matrix. To ensure scalability, the new alloy was made through arc-melting and ingot-casting followed by hot forging, cold rolling and heat treatments of homogenization and precipitation aging. The microstructure was characterized by SEM, TEM, XRD and APT, confirming the existence of nanoprecipitates predicted in the thermodynamic calculations. In addition to microstructural evaluation tensile properties at room temperature and 700 °C, and Charpy impact energy at room temperature were measured. The microstructure and mechanical properties were then compared with those from a historic reference V44 alloy. The tensile strength improvement in V44C was rationalized based on particle and solid solution strengthening mechanism. The fracture behavior was discussed based on the fractography results and necking deformation behavior.

Alloys development↗
DOE OSTI2024

Ab initio property predictions of quinary solid solutions using small binary cells

The Set of Small Ordered Structures (SSOS) approach is an ab initio technique for modelling random solid solutions in which many small structures are averaged so that their correlation functions match those of a desired composition. SSOS has been shown to be effective in reducing the cost of density functional theory calculations relative to other well-known techniques such as cluster expansions and special quasirandom structures for modelling solid solutions. Here in this work, we demonstrate that SSOS’s can be constructed using cells with only a subset of elements while still accurately modelling multi-component systems. Specifically, we show that small binary cells can effectively model two quinary high entropy alloys – NbTaTiHfZr and MoNbTaVW – accurately capturing properties such as formation energy, lattice parameters, elastic constants, and root-mean-square atomic displacements. Overall, this insight is useful for those looking to construct databases of such small structures for predicting the properties of multi-component solid solutions, as it greatly decreases the number of structures that needs to be considered.

36 MATERIALS SCIENCE↗
DOE OSTI2024

First-principles calculation of lattice distortion, electronic structure, and bonding properties of GeTe-based and PbSe-based high-entropy chalcogenides

The massive amount of wasted heat energy from industry has pushed the development of thermoelectric (TE) materials that directly convert heat into electricity to a new level of concern. Recently, multicomponent alloys such as GeTe-based and PbSe-based high-entropy (HE) chalcogenides have attracted a great deal of attention due to their potential application as TE materials. The nature of the interatomic bonding, lattice distortion (LD), and the electronic structure in this class of materials is not fully understood. Herein, we report a comprehensive computational investigation of nine GeTe-based HE alloys with eight metallic elements (Ag, Pb, Sb, Bi, Cu, Cd, Mn, and Sn) with large supercells of 1080 atoms each; seven PbSe-based HE solid solutions: Pb0.99−ySb0.012SnySe1−2xTexSx (x = 0.1, 0.2, 0.25, 0.3, 0.35, 0.4, 0.45, with y = 0) with supercells of 1000 atoms each; and five Pb0.99−ySb0.012SnySe1−2xTexSx (y = 0.05, 0.1, 0.15, 0.2, 0.25 with x = 0.25) solid solutions with supercells of 1000 atoms each. All these HE models are theoretically investigated for the first time. The electronic structure, interatomic bonding, charge transfer, and lattice distortion (LD) are investigated by first-principles calculations based on density functional theory. Multicomponent HE alloys can cause a significant LD, which affects their mechanical, thermal, and TE properties. The calculations for the GeTe-based HE chalcogenides showed that they are semiconductors with a narrow bandgap, except for m8, which has a semi-metallic characteristic, and this makes them good candidates for TE applications. For most of these models, the Fermi level shifts upward and locates deeply in the conduction bands, resulting in the enhancement of the electrical conductivity (σ). The bonding properties showed that most bonds in m5 are more dispersed, indicating highest LD and lower lattice thermal conductivity. For PbSe-based HE solid solutions, the LD calculations showed that the models Pb0.99Sb0.012Se0.5Te0.25S0.25 and Pb0.89Sb0.012Sn0.1Se0.5Te0.25S0.25 have the higher LD, and thus a lower lattice thermal conductivity. Such investigations are in high demand since it enables us to design new HE chalcogenides for TE applications. We use the novel concept of total bond order density as a single quantum mechanical metric to characterize the internal cohesion of these HE alloys and correlate with calculated properties, especially the mechanical properties. This work provides a solid database for HE chalcogenides and a road map for many potential applications. Moreover, the computational procedure we developed can be used to design new HE chalcogenides for specific TE applications.

Physics↗
DOE OSTI2025

Grain Boundary Segregation Suppresses Local Short‐Range Ordering in Nanocrystalline High‐Entropy Alloys

Multi-principal-element alloys like high-entropy alloys (HEAs) have potential applications in many engineering fields due to their unique mechanical/functional properties. While HEAs are generally considered random solid solutions, recent studies revealed that they are prone to short-range-ordering (SRO) due to the complex multi-pair-wise interactions among the constituent elements. Meanwhile, SROs' evolution can sometimes be deleterious, and it is necessary to have control over their evolution. Examining the AlCoCrFe-Zr model alloy, long-range ordering occurs following the expectation of enthalpic predictions. Advanced characterization techniques—transmission electron microscopy, high-energy synchrotron X-ray diffraction/pair distribution function, and atom probe tomography, reveal that SRO is suppressed in as-milled and GB-decorated NC-(AlCoCrFe)100-xZrx (x = 0–1.5 atomic %). Warren-Cowley coefficient calculations are further used to validate the suppression of SRO. Besides the low segregation enthalpies of Cr, Fe, and Zr, and the high-mixing enthalpy of Cr and Fe, the short diffusion path to GBs due to high-GB density in the NC-HEAs and the higher energy state of the GBs than the matrix promotes GB-segregation that further alters the matrix chemistry and consequently disfavors SRO formation within the matrix. Despite the GB-segregation of Cr, Fe, and Zr, the matrices and GBs remain in a random solid solution.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Computational Design of Interlayers for Thermally Stable Compositionally Graded Coatings on Nickel Alloys

To extend the service life of Ni-based superalloys, refractory metal coatings are often used. However, direct bonding between metals with dissimilar crystal structure promotes brittle intermetallic phase formation. This work presents a computational thermodynamic framework for high throughput design of functionally graded interlayers to suppress deleterious phases that may form at the interlayer. The Thermo-Calc software package was used to screen candidate metallic interlayer elements based on stability of solid-solution phases. Vanadium was identified as a promising interlayer due to its consistent suppression of intermetallic phases. Temperature-dependent phase diagram mapping between 600 and 1000 °C guided selection of a compositional pathway that significantly reduced intermetallic formation compared to directly joining the Ni-based and Nb refractory alloys. Time–temperature–transformation analysis was performed to assess whether equilibrium-predicted phases are kinetically accessible along regions of the graded path where non-solid-solution phases are not fully suppressed. The methodology was further applied to additional Ni-based alloy and coating systems, illustrating its transferability as an approach for rapid computational design of graded interlayers in dissimilar high-temperature materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Systematic discovery of new nano-scale metastable intermetallic eutectic phases in laser rapid solidified Aluminum-Germanium alloy

Laser surface remelting of as-cast Al-Ge eutectic alloy is shown to produce ultrafine lamellar eutectic morphology with interlamellar spacing refined up to ∼60 nm and composed of FCC Al solid solution and unusual Al x Ge y intermetallic phases that do not form during near-equilibrium solidification. The microstructures are characterized and analyzed using a combination of selected area electron diffraction, high-resolution scanning transmission electron microscopy, energy dispersive X-ray spectroscopy to obtain high-resolution elemental maps, and atomistic modeling using density functional theory followed by atomic-scale image simulation. Depending on the local solidification conditions, the crystallography of the Al x Ge y intermetallic phases in the eutectic microstructure is either monoclinic (C 2/c) or monoclinic (P 2 1 ), with high densities of defects in both cases. This is in sharp contrast to the as-cast alloys that showed nominally pure Al and Ge phases with significant solute partitioning and equilibrium FCC and diamond cubic crystal structures, respectively. Corresponding kinetic phase diagrams are proposed to interpret the evolution of nano-lamellar eutectic morphologies with equilibrium Al and metastable Al x Ge y phases, and to explain increased solid solubility in the Al phases manifested by precipitation of ultrafine clusters of Ge. Furthermore, the reasons for the formation of these metastable eutectics under laser rapid solidification are discussed from the perspective of the competitive growth criterion.

Al-Ge eutectic↗