Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Scattering, Radiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Uranian H Ly-alpha emission - The interstellar wind source

IUE observation of Uranian emissions in hydrogen Lyman alpha (H Ly-alpha) over the past four years have recently been summarized by Clarke et al. (1985). Over this time period they find an average H Ly-alpha brightness of 1260 R which they estimate is composed of 200 R of solar scattered radiation and 1060 R from a collisional source. A third component, not considered by previous authors, is the reflection of H Ly-alpha emissions from the interstellar wind. Hydrogen in the interstellar wind forms an extended source of H Ly-alpha whose importance relative to the solar flux increases with distance from the sun. The present paper demonstrates that scattering of interstellar H Ly-alpha is more important than scattering of solar H Ly-alpha for reasonable values of H column abundance and, in fact, may make up 10-40 percent of the observed signal. Large H column abundances are still required to explain the H Ly-alpha brightness solely on the basis of resonant scattering; therefore it is likely that the emissions are due in part to collisional sources and in part to the scattering of interstellar H Ly-alpha with solar scattering playing a minor role.

Yelle, R. V.↗
DOE OSTI2024

Qualitative Conditions for Reasonable Estimates of Kerma Using Total and Kerma Cross Section Attenuation of Photons

Performing a full adjoint simulation in the Integrated Tiger Series (ITS) can be time consuming to obtain statistically significant results. The ray-trace capability in ITS allows for rapid scoping calculations of the uncollided kerma from photon sources without needing to run a full adjoint simulation. However, the uncollided estimate will always underestimate the full-physics kerma since it neglects scattered radiation, and under certain conditions, the result from the capability may not provide a sufficiently accurate estimate of the full-physics kerma. To exemplify the conditions in which the capability provides reasonable estimates, two problem geometries with different materials are simulated using the full adjoint capability as well as the ray-trace capability with a total cross section treatment and a new kerma-attenuation cross-section treatment. The results are then compared to show under which conditions the estimates are accurate. Reasonable estimates are provided from the ray-trace feature when there is minimal scattering into a region of interest occurring, such as with low-Z material and when the photons travel through small amounts of material.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS2019

Spectral Polarization Distribution Models (PDMs) for NASA CLARREO Pathfinder’s Inter-Calibration Applications

Solar radiation scattered by Earth surfaces of various scene types such as oceans, deserts, tree leaves etc and atmospheric molecules and particles is polarized and the amount of polarization depends on the surface composition and particle physical properties. This can be a source of measurement errors in satellite data if a non-polarimetric radiometric sensor is sensitive to the polarization state of light. To obtain highly accurate spectral solar radiation data from the Earth-atmosphere system for the space-borne inter-calibration studies as proposed in NASA's Climate Absolute Radiance and Refractivity Observatory (CLARREO) mission and the CLARREO Pathfinder (CPF) mission, the spectral polarization state of the reflected solar light at the top of atmosphere (TOA) must be known with sufficient accuracy. The degree of polarization (DOP) and the angle of linear polarization (AOLP) of the light at the TOA as functions of incident and viewing geometry and scene type construct the Polarization Distribution Models (PDMs) for correction of polarization-induced error of satellite data. In this work, algorithms for modeling the spectral polarization state of reflected sunlight from various types of Earth, including oceans, deserts, vegetated land surfaces and these scene types with all kinds of clouds, are developed. By comparing the model results with the PARASOL satellite data, our numerical results demonstrate that the model can provide a reliable approach for making the spectral PDMs for wavelengths between 320 and 2300 nm for satellite inter-calibration applications as proposed in the CLARREO and the CLARREO CPF missions.

Sun, Wenbo↗
NASA NTRS1990

Applicability of steady models for hot-star winds

Non-Sobolev models of radiatively driven stellar winds based on a pure-absorption approximation do not have a well-defined steady state. Here the implications of this for flow time-dependence are examined, showing that, under such circumstances, instabilities in the flow attain an absolute character that leads to intrinsic variability. In this case, steady solutions are inherently inapplicable because they do not represent physically realizable states. However, for actual hot-star winds, driving is principally by scattering, not pure absorption. In practice, the relatively weak force associated with slight asymmetries in the diffuse, scattered radiation field may play a crucial role in breaking the solution degeneracy and reducing the instability from an absolute to an advective character.

Owocki, Stanley P.↗
NASA NTRS1973

The influence of ozone and aerosols on the brightness and color of the twilight zone

The radiance and color of the twilight sky are calculated for single scattered radiation with the use of spherically symmetric models of the earth's atmosphere. Spherical geometry is used throughout the calculations with no plane parallel approximations. Refraction effects are taken into account through fine subdivision of the atmosphere into spherical shells of fixed index of refraction. Shell's law of refraction is used to calculate a direction of travel each time that a photon traverses the interface between layers. Five different models of the atmosphere were used: a pure molecular scattering atmosphere; molecular atmosphere plus ozone absorption; and three models with aerosol concentrations of 1, 3, and 10 times normal together with molecular scattering and ozone absorption. The results of the calculations are shown for various observation positions and local viewing angles in the solar plane for wavelengths in the range of 0.40 microns to 0.75 microns.

Adams, C. N.↗
NASA NTRS1974

The influence of ozone and aerosols on the brightness and color of the twilight sky

The radiance and color of the twilight sky are calculated for single scattered radiation with the use of spherically symmetric models of the earth's atmosphere. Spherical geometry is used throughout the calculations with no plane-parallel approximations. Refraction effects are taken into account through fine subdivision of the atmosphere into spherical shells of fixed index of refraction. Snell's law of refraction is used to calculate a new direction of travel each time that a photon traverses the interface between layers. Five different models of the atmosphere were used: a pure molecular scattering atmosphere; molecular atmosphere plus ozone absorption; and three models with aerosol concentrations of one, three, and ten times normal together with molecular scattering and ozone absorption. The results of the calculations are shown for various observation positions and local viewing angles in the solar plane for wavelengths in the range from 0.40 to 0.75 micron.

Adams, C. N.↗
NASA NTRS2017

Retrieval of Water Vapor Column Abundance and Aerosol Properties from ChemCam Passive Sky Spectroscopy

We derive water vapor column abundances and aerosol properties from Mars Science Laboratory (MSL) ChemCam passive mode observations of scattered sky light. This paper covers the methodology and initial results for water vapor and also provides preliminary results for aerosols. The data set presented here includes the results of 113 observations spanning from Mars Year 31 L(s) = 291 deg (March 30, 2013) to Mars Year 33 L(s) = 127 deg (March 24, 2016). Each ChemCam passive sky observation acquires spectra at two different elevation angles. We fit these spectra with a discrete-ordinates multiple scattering radiative transfer model, using the correlated-k approximation for gas absorption bands. The retrieval proceeds by first fitting the continuum of the ratio of the two elevation angles to solve for aerosol properties, and then fitting the continuum-removed ratio to solve for gas abundances. The final step of the retrieval makes use of the observed CO 2 absorptions and the known CO 2 abundance to correct the retrieved water vapor abundance for the effects of the vertical distribution of scattering aerosols and to derive an aerosol scale height parameter. Our water vapor results give water vapor column abundance with a precision of +/-0.6 precipitable microns and systematic errors no larger than +/-0.3 precipitable microns, assuming uniform vertical mixing. The ChemCam-retrieved water abundances show, with only a few exceptions, the same seasonal behavior and the same timing of seasonal minima and maxima as the TES, CRISM, and REMS-H data sets that we compare them to. However ChemCam-retrieved water abundances are generally lower than zonal and regional scale from-orbit water vapor data, while at the same time being significantly larger than pre-dawn REMS-H abundances. Pending further analysis of REMS-H volume mixing ratio uncertainties, the differences between ChemCam and REMS-H pre-dawn mixing ratios appear to be much too large to be explained by large scale circulations and thus they tend to support the hypothesis of substantial diurnal interactions of water vapor with the surface. Our preliminary aerosol results, meanwhile, show the expected seasonal pattern in dust particle size but also indicate a surprising interannual increase in water-ice cloud opacities.

Mcconnochie, Timothy H.↗
DOE OSTI2022

A poloidal high- k scattering system for NSTX-U

A previous 5-channel tangential high-k scattering system is being replaced by an 8-channel, poloidal high-k scattering system on the National Spherical Torus eXperiment Upgrade (NSTX-U) device located in Princeton, NJ, USA. The 693 GHz poloidal scattering system replaces a 280 GHz tangential scattering system to study high-k electron density fluctuations on NSTX-U, thereby considerably enhancing planned turbulence physics studies by providing a measurement of the k θ -spectrum of both electron temperature gradient (ETG) and ion temperature gradient (ITG) modes. Two approaches to generating the 693 GHz probe beam are under development: an optically-pumped far-infrared (FIR) laser that generates ~50 mW, and a compact gyrotron that can potentially generate in excess of 5 W. Large aperture optics collect radiation scattered from density fluctuations in the plasma core at 8 simultaneous scattering angles ranging from 2 to 15° corresponding to poloidal wavenumbers that extend to >40 cm -1 . Finally, steerable launch optics coupled with receiver optics mounted on a 5-axis receiver carriage allow the scattering volume to be placed radially from r/a = 0.3 out to the pedestal region (r/a ~ 0.99) and translated horizontally as needed to satisfy wavenumber matching.

47 OTHER INSTRUMENTATION↗
NASA NTRS1976

Calculations of polarization and radiance in the atmosphere

Two different methods for the solution of radiative transfer problems, matrix operator and Monte Carlo, are discussed. As an example of the use of the method, results are given for the radiance and polarization of the radiation scattered from haze layers as well as from models of the real atmosphere. The variation of the radiance, polarization, and ellipticity with the aerosol amount in the real atmosphere model is presented. The Monte Carlo method is applied to the problem of calculation of the radiance and polarization of the photons in the atmosphere when there is an ocean as the lower surface. It is found that the turbidity of the ocean can be deduced from the upwelling radiance measured at some height in the atmosphere. The downwelling radiation just beneath the ocean surface is elliptically polarized at those angles where it is derived from the total internal reflection of the upwelling radiation at the ocean surface.

Plass, G. N.↗
NASA NTRS2020

Response of Surface Shortwave Cloud Radiative Effect to Greenhouse Gases and Aerosols and Its Impact on Summer Maximum Temperature

Shortwave cloud radiative effects (SWCREs), defined as the difference of the shortwave radiative flux between all-sky and clear-sky conditions at the surface, have been reported to play an important role in influencing the Earth's energy budget and temperature extremes. In this study, we employed a set of global climate models to examine the SWCRE responses to CO2, black carbon (BC) aerosols, and sulfate aerosols in boreal summer over the Northern Hemisphere. We found that CO2 causes positive SWCRE changes over most of the NH, and BC causes similar positive responses over North America, Europe, and eastern China but negative SWCRE over India and tropical Africa. When normalized by effective radiative forcing, the SWCRE from BC is roughly 3–5 times larger than that from CO2. SWCRE change is mainly due to cloud cover changes resulting from changes in relative humidity (RH) and, to a lesser extent, changes in cloud liquid water, circulation, dynamics, and stability. The SWCRE response to sulfate aerosols, however, is negligible compared to that for CO2 and BC because part of the radiation scattered by clouds under all-sky conditions will also be scattered by aerosols under clear-sky conditions. Using a multilinear regression model, it is found that mean daily maximum temperature (Tmax) increases by 0.15 and 0.13 K per watt per square meter (W m−2) increase in local SWCRE under the CO2 and BC experiment, respectively. When domain-averaged, the contribution of SWCRE change to summer mean Tmax changes was 10 %–30 % under CO2 forcing and 30 %–50 % under BC forcing, varying by region, which can have important implications for extreme climatic events and socioeconomic activities.

surface shortwave cloud radiative effect↗
NASA NTRS2001

A Strategy to Assess Aerosol Direct Radiative Forcing of Climate Using Satellite Radiation Measurements

Atmospheric aerosols have a complex internal chemical composition and optical properties. Therefore it is difficult to model their impact on redistribution and absorption of solar radiation, and the consequent impact on atmospheric dynamics and climate. The use in climate models of isolated aerosol parameters retrieved from satellite data (e.g. optical thickness) may result in inconsistent calculations, if the model assumptions differ from these of the satellite retrieval schemes. Here we suggest a strategy to assess the direct impact of aerosol on the radiation budget at the top and bottom of the atmosphere using satellite and ground based measurements of the spectral solar radiation scattered by the aerosol. This method ensures consistent use of the satellite data and increases its accuracy. For Kaufman and Tanre: Strategy for aerosol direct forcing anthropogenic aerosol in the fine mode (e.g. biomass burning smoke and urban pollution) consistent use of satellite derived optical thickness can yield the aerosol impact on the spectral solar flux with accuracy an order of magnitude better than the optical thickness itself. For example, a simulated monthly average smoke optical thickness of 0.5 at 0.55 microns (forcing of 40-50 W/sq m) derived with an error of 20%, while the forcing can be measured directly with an error of only 0-2 W/sq m. Another example, the effect of large dust particles on reflection of solar flux can be derived three times better than retrievals of optical thickness. Since aerosol impacts not only the top of the atmosphere but also the surface irradiation, a combination of satellite and ground based measurements of the spectral flux, can be the most direct mechanism to evaluate the aerosol effect on climate and assimilate it in climate models. The strategy is applied to measurements from SCAR-B and the Tarfox experiments. In SCAR-B aircraft spectral data are used to derive the 24 hour radiative forcing of smoke at the top of the atmosphere of (Delta)F(sub 24hr)/(Delta)tau = - 25 +/- 5 W/sq m. Ground based data give forcing at the surface of (Delta)F(sub 24hr)/(Delta)taur = -80 +/- 5 W/sq m. In TARFOX a mixture of maritime and regional pollution aerosol resulted in a varied forcing at the top of the atmosphere, (Delta)F(sub 24hr)/(Delta)tau, between -26 W/sq 2 and -50 W/sq m depending on mixture of coarse and accumulation modes, for Angstrom exponents of 1.0 and 0.2 respectively.

Kaufman, Yoram J.↗
DOE OSTI2025

Hydrodynamic expansion and near-infrared absorption of x-ray heated aluminum plasmas

We use x-ray pulses from dense argon plasmas at the Z Machine (Sandia National Laboratories) to generate hypersonic aluminum plasmas akin to material ejecta during proposed planetary defense missions, fusion reactor wall excursions, and other high-energy density processes. Near-infrared absorption is used to diagnose the controlled expansion of the plasmas through cylindrical cavities following their generation from x-ray heating of solid aluminum 7075 alloy. The data are compared to multidimensional radiation hydrodynamics simulations utilizing the ALEGRA multiphysics code, accounting for the dynamics of radiation scattering, material phase change, plasma expansion, thermal re-irradiation, and interactions with the cavity and with the infrared beams. To allow for accurate simulation, density functional theory is used to apply the Hagen–Rubens relation for the far-infrared and is adjoined with a detailed configuration accounting model using the Propaceos code, producing opacities spanning 10 −1 –10 4 eV photon energy for aluminum 7075 alloy, and in comparison with pure aluminum. The model is found to agree with experimental data in the higher-fluence regime when the Hagen–Rubens relation is applied. The ejected material, which is observed to travel up to 55 km/s, is comprised of a strongly ionized, non-LTE plasma front at ∼10 eV temperature followed by a weakly ionized LTE gas at higher density. The present findings lend some confidence to the broad-range equation of state and infrared opacity models for weakly ionized aluminum plasmas while demonstrating an approach to their future refinement, with potential application to astrophysical plasmas and other extreme processes.

Adiabatic process↗
DOE OSTI2024

Isotopic gamma lines for identification of shielding materials

Identifying the constituting materials of concealed objects is crucial in a wide range of sectors, such as medical imaging, geophysics, nonproliferation, national security investigations, and so on. Existing methods face limitations, particularly when multiple materials are involved or when there are challenges posed by scattered radiation and large areal mass. Here we introduce a novel brute-force statistical approach for material identification using high spectral resolution detectors, such as HPGe. The method relies upon updated semianalytic formulae for computing uncollided flux from source of gamma radiation, shielded by a sequence of nested spherical or cylindrical materials. These semianalytical formulae make possible rapid flux estimation for material characterization via combinatorial search through all possible combinations of materials, using a high-resolution HPGe counting detector. An important prerequisite for the method is that the geometry of the objects is known (for example, from X-ray radiography). We demonstrate the viability of this material characterization technique in several use cases with both simulated and experimental data in spherical geometry.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2020

Improving inverse Compton sources by avoiding non-linearities

We present a new, more nuanced understanding of non-linear effects in inverse Compton sources. Deleterious non-linear effects can arise even at low laser intensities, a regime previously viewed as linear. After laying out a survey of non-linear phenomena which degrade the effectiveness of inverse Compton sources, we discuss two powerful techniques designed to avoid these non-linearities. Starting with the known technique of non-linear longitudinal chirping of the laser pulse in the high laser field regime, we show that the simple stretching of the laser pulse, while keeping the energy constant, can significantly increase the spectral density of the scattered radiation in many operating regimes. Our numerical simulations show that combining these two techniques avoids detrimental non-linearities and improves the performance of inverse Compton sources over an order of magnitude.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Selected Field Measurement Topics [Slides]

Various measurements were conducted with a NaI FLIR IdentiFINDER2 to examine the effects of: the radiation scattering environment, hotspot misalignment effects, dead time, INL Coin, neutrons, and thermal variations. This brief study is by no means conclusive but it offers examples of how the conditions of the measurement can affect the result.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

High Fidelity Tomographic Density Reconstructions [Slides]

Pressed high explosives have small density variations associated with the pressing process, from a few to sub percent depending on the material. Variations at these levels are known to have an impact on HE performance. Currently, a destructive testing method based on physical sectioning followed by immersion density measurements (slice and dice) is utilized. However, this method has poor spatial resolution limited by the the sectioning size, 1-2 cm. If possible, radiographic methods including Computed Tomography (CT) would be preferred, as they are non-destructive and have higher (less than .1 mm) spatial resolution. However, beam hardening, scattered radiation, and detector effects make density reconstructions at this level extremely challenging.

42 ENGINEERING↗