SEARCH · Engineering Papers

Results for “STRESS CONCENTRATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS2011

A Method of Strengthening Composite/Metal Joints

The term tape setback method denotes a method of designing and fabricating bonded joints between (1) box beams or other structural members made of laminated composite (matrix/ fiber) materials and (2) metal end fittings used to fasten these structural members to other structural members. The basic idea of the tape setback method is to mask the bonded interface between the metallic end fitting and composite member such that the bond does not extend out to the free edges of the composite member. The purpose served by the tape setback method is to strengthen the joints by decoupling stress concentrations from edge defects, which can cause premature failures. A related prior method that serves a similar purpose, involving the use of tapered adherends at the joints, can be too difficult and costly to be acceptable in some applications. The tape setback method offers an easier, less costly alternative. The structural members to which the method was originally applied were box beams in the form of composite tubes having flat faces with rounded corners. The end fittings were plugs made of a low-thermal- expansion nickel/iron alloy (see figure). In computational-simulation studies of tensile and compressive loading of members without tape setback, stresses were found to be concentrated at the free end edges of the composite tubes, and inspection of members that had been subjected to real tension and compression tests showed that cracks started at the free end edges. As applied to these members, the tape setback method makes them less vulnerable to initiation of failure at edge defects produced during fabrication. In real tension tests of comparable members without and with tape setback, the average mean tensile strength of the members with tape setback was found to be 1.9 times that of the members without tape setback.

Polis, Daniel L.↗

NASA NTRS2011

Detecting Damage in Ceramic Matrix Composites Using Electrical Resistance

The majority of damage in SiC/SiC ceramic matrix composites subjected to monotonic tensile loads is in the form of distributed matrix cracks. These cracks initiate near stress concentrations, such as 90 deg fiber tows or large matrix pores and continue to accumulate with additional stress until matrix crack saturation is achieved. Such damage is difficult to detect with conventional nondestructive evaluation techniques (immersion ultrasonics, x-ray, etc.). Monitoring a specimen.s electrical resistance change provides an indirect approach for monitoring matrix crack density. Sylramic-iBN fiber- reinforced SiC composites with a melt infiltrated (MI) matrix were tensile tested at room temperature. Results showed an increase in resistance of more than 500% prior to fracture, which can be detected either in situ or post-damage. A relationship between resistance change and matrix crack density was also determined.

Smith, Craig E.↗

NASA NTRS1986

A failure mechanism in Al-SiC composites

Divecha et al. (1981) have discussed the advantages of materials obtained by adding silicon carbide whiskers to commercial aluminum alloys, taking into account also certain problems which are related to poor ductility and low fracture toughness. The present investigation has the objective to advance the understanding of the deformation at the whisker ends in reinforced aluminum composites through both observation and analysis. It is suggested that the low fracture toughness of the considered materials is the result of the rapid accumulation of damage at the whisker ends. It is pointed out that the whisker ends are sites of severe stress concentration and intense localized plastic strain. In connection with this situation, voids nucleate and grow at relatively low macroscopic stress levels. The reported studies include an examination of the deformation microstructure beneath the fracture surfaces of specimens with the aid of transmission electron microscopy.

Nutt, S. R.↗

DOE OSTI2024

Shape Matters: Understanding the Effect of Electrode Geometry on Cell Resistance and Chemo-Mechanical Stress

Rechargeable batteries that incorporate shaped three-dimensional electrodes have been shown to have increased power and energy densities when compared to a conventional geometry, i.e. a planar cathode and anode that sandwich an electrolyte. Electrodes can be shaped to enable a higher active material loading, while keeping ion transport distances small. However, the relationship between electrical and mechanical performance of shaped electrodes remains poorly understood. Many electrode designs have been explored, where the electrodes are individually shaped or intertwined, and advances in manufacturing and shape/topology optimization have made such designs a reality. Here, we explore sinusoidal half cells and interdigitated full cells. First, we use a simple electrostatics model to understand the cell resistance as a function of shape. Here we focus on low-temperature conditions, where the electrolyte conductivity decreases relative to that of the electrode; here, LiPF 6 EC:DMC electrolyte and MnO 2 electrode are considered. Next, we use a chemo-mechanics model to examine the stress that arises due to intercalation-driven volume expansion. We show that shaped electrodes provide a significant reduction in resistance in low-temperature conditions, however, they exhibit unfavorable stress concentrations. Overall, we find that the fully interdigitated electrodes may provide the best balance with respect to this resistance-stress trade-off.

25 ENERGY STORAGE↗

DOE OSTI2025

Fundamental Study of Fatigue Crack Initiation at Grain and Twin Boundaries in Austentic Stainless Steel (Final Technical Report)

The overarching goal of this project was to understand the dislocation-based mechanisms driving fatigue crack initiation at grain and twin boundaries. The hypothesis of the work is that dislocation structures equivalent to persistent slip bands (PSBs) form in the boundaries, leading to local stress concentrations and fatigue crack initiation. The sub-goals associated with this work include: • Understanding the evolution of the dynamic stress state and dislocation density surrounding PSB/grain boundary interactions. This will require the development of new techniques that couple high resolution electron backscatter diffraction (HREBSD) with in situ scanning electron microscopy (SEM) deformation. • Uncover the mechanisms by which dislocations are accommodated in grain and twin boundaries during fatigue. The proposed approach here is to conduct in situ transmission electron microscopy (TEM) deformation experiments on fatigued samples. • Establish correlations between microstructure, deformation accommodation, and crack initiation across time and length scales. This work primarily focuses on understanding fatigue crack initiation in austenitic stainless steels, though promising work by an undergraduate researcher extended the work to high purity Al.

42 ENGINEERING↗

NASA NTRS1986

Stress patterns in an interplate shear zone - An effective anisotropic model and implications for the Transverse Ranges, California

The pervasive Quaternary strike-slip (or wrench) structure that occurs in southern California is analyzed by solving a series of planar, linear elastic boundary value problems of tractional type that assume pure shear forces at infinity. It is concluded that the cross-cutting tectonic fabric of the Transverse Ranges in southern California causes the Ranges to act as a stress concentrator. In addition, it is found that rigid rotation of the Transverse Ranges is mechanically supported by an asymmetric distribution of stress and elastic strain encircling it. It is noted that for Quaternary tectonic orientation, a clockwise sense to this rotation is expected.

Ivins, E. R.↗

NASA NTRS1990

The assessment of metal fiber reinforced polymeric composites

Because of their low cost, excellent electrical conductivity, high specific strength (strength/density), and high specific modulus (modulus/density) short metal fiber reinforced composites have enjoyed a widespread use in many critical applications such as automotive industry, aircraft manufacturing, national defense, and space technology. However, little data has been found in the study of short metal fibrous composites. Optimum fiber concentration in a resin matrix and fiber aspect ratio (length-to-diameter ratio) are often not available to a user. Stress concentration at short fiber ends is the other concern when the composite is applied to a load-bearing application. Fracture in such composites where the damage will be initiated or accumulated is usually difficult to be determined. An experimental investigation is therefore carefully designed and undertaken to systematically evaluate the mechanical properties as well as electrical properties. Inconel 601 (nickel based) metal fiber with a diameter of eight microns is used to reinforce commercially available thermoset polyester resin. Mechanical testing such as tensile, impact, and flexure tests along with electrical conductivity measurements is conducted to study the feasibility of using such composites. The advantages and limitations of applying chopped metal fiber reinforced polymeric composites are also discussed.

Chung, Wenchiang R.↗

NASA NTRS1997

Fiber Contraction Approaches for Improving CMC Proportional Limit

The fact that the service life of ceramic matrix composites (CMC) decreases dramatically for stresses above the CMC proportional limit has triggered a variety of research activities to develop microstructural approaches that can significantly improve this limit. As discussed in a previous report, both local and global approaches exist for hindering the propagation of cracks through the CMC matrix, the physical source for the proportional limit. Local approaches include: (1) minimizing fiber diameter and matrix modulus; (2) maximizing fiber volume fraction, fiber modulus, and matrix toughness; and (3) optimizing fiber-matrix interfacial shear strength; all of which should reduce the stress concentration at the tip of cracks pre existing or created in the matrix during CMC service. Global approaches, as with pre-stressed concrete, center on seeking mechanisms for utilizing the reinforcing fiber to subject the matrix to in-situ compressive stresses which will remain stable during CMC service. Demonstrated CMC examples for the viability of this residual stress approach are based on strain mismatches between the fiber and matrix in their free states, such as, thermal expansion mismatch and creep mismatch. However, these particular mismatch approaches are application limited in that the residual stresses from expansion mismatch are optimum only at low CMC service temperatures and the residual stresses from creep mismatch are typically unidirectional and difficult to implement in complex-shaped CMC.

DiCarlo, James A.↗

NASA NTRS2012

Thermostructural Evaluation of Joggle Region on the Shuttle Orbiter's Wing Leading Edge

An investigation was initiated to determine the cause of coating spallation occurring on the Shuttle Orbiter's wing leading edge panels in the slip-side joggle region. The coating spallation events were observed, post flight, on differing panels on different missions. As part of the investigation, the high re-entry heating occurring on the joggles was considered here as a possible cause. Thus, a thermostructural evaluation was conducted to determine the detailed state-of-stress in the joggle region during re-entry and the feasibility of a laboratory test on a local joggle specimen to replicate this state-of-stress. A detailed three-dimensional finite element model of a panel slip-side joggle region was developed. Parametric and sensitivity studies revealed significant stresses occur in the joggle during peak heating. A critical interlaminar normal stress concentration was predicted in the substrate at the coating interface and was confined to the curved joggle region. Specifically, the high interlaminar normal stress is identified to be the cause for the occurrence of failure in the form of local subsurface material separation occurring in the slip-side joggle. The predicted critical stresses are coincident with material separations that had been observed with microscopy in joggle specimens obtained from flight panels.

Walker, Sandra P.↗

NASA NTRS1983

Optimization of bonded joints

A procedure for minimizing the elastic shear stress concentration in adhesive lap joints is presented. The proposed method is based upon tapering the adherends to achieve smooth stiffness transitions and uniform shear stresses. Both single and double lap splices are considered, but numerical examples are restricted to the case of double lap joints. Nonisotropic materials and nonoptimum design limitations, such as minimum and maximum thickness adherends, load-line eccentricity, and peel stresses are treated, and typical results are presented.

Ojalvo, I. U.↗

NASA NTRS1991

Traction free finite elements with the assumed stress hybrid model

An effective approach in the finite element analysis of the stress field at the traction free boundary of a solid continuum was studied. Conventional displacement and assumed stress finite elements were used in the determination of stress concentrations around circular and elliptical holes. Specialized hybrid elements were then developed to improve the satisfaction of prescribed traction boundary conditions. Results of the stress analysis indicated that finite elements which exactly satisfy the free stress boundary conditions are the most accurate and efficient in such problems. A general approach for hybrid finite elements which incorporate traction free boundaries of arbitrary geometry was formulated.

Kafie, Kurosh↗

DOE OSTI2024

On the Mechanical Behavior of LP-DED C103 Thin-Wall Structures

Laser Powder Directed Energy Deposition (LP-DED) can produce thin-wall features on the order of 1 mm. These features are essential for large structures operating in extreme environments such as regeneratively cooled nozzles and heat exchangers, which often make use of refractory metals. In this work, the mechanical behavior of LP-DED C103 was investigated via quasi-static tensile testing and low cycle fatigue (LCF) testing. The effects of vacuum stress relief (SR) and hot isostatic pressing (HIP) heat treatments were investigated for specimens in the vertical and horizontal build orientations during tensile testing. The AB and SR properties were lower than literature values for wrought and laser powder bed fusion (L-PBF) bulk components but higher than electron beam powder bed fusion (EB-PBF). The application of a HIP cycle improved strength by 7% and ductility by 27% past the initial as-built condition. Fracture images reveal that interlayer stress concentration sites are responsible for fracture in specimens in the vertical orientation. Meanwhile, fracture in the horizontal specimens mainly propagates at a slanted angle typical of plane stress conditions. The LCF results show cycles to failure ranging from 100 cycles to 8000 cycles for max strain levels of 2% and 0.5%, respectively. Fractography on the fatigue specimens reveals an increasing propagation zone as max strain levels are increased. The impact of these findings and future work are discussed in detail.

36 MATERIALS SCIENCE↗

NASA NTRS2003

Development of a Fatigue Crack Growth Coupon for Highly Plastic Stress Conditions

This paper presents an analytical approach used to develop a novel fatigue crack growth coupon for a highly plastic 3-D stress field condition. The flight hardware investigated in this paper is a large separation bolt that fractures using pyrotechnics at the appointed time during the flight sequence. The separation bolt has a deep notch that produces a severe stress concentration and a large plastic zone when highly loaded. For this geometry, linear-elastic fracture mechanics (LEFM) techniques are not valid due to the large nonlinear stress field. Unfortunately, industry codes that are generally available for fracture mechanics analysis and fatigue crack growth (e.g. NASGRO (11) are limited to LEFM and are available for only a limited number of geometries. The results of LEFM based codes are questionable when used on geometries with significant plasticity. Therefore elastic-plastic fracture mechanics (EPFM) techniques using the finite element method (FEM) were used to analyze the bolt and test coupons. scale flight hardware is very costly in t e r n of assets, laboratory resources, and schedule. Therefore to alleviate some of these problems, a series of novel test coupons were developed to simulate the elastic-plastic stress field present in the bolt.

Allen, Phillip A.↗

NASA NTRS1982

The effects of inherent flaws on the time and rate dependent failure of adhesively bonded joints

Inherent flaws, as well as the effects of rate and time, are shown by tests on viscoelastic adhesive-bonded single lap joints to be as critical in joint failure as environmental and stress concentration effects, with random inherent flaws and loading rate changes resulting in an up to 40% reduction in joint strength. It is also found that the asymptotic creep stress, below which no delayed failure may occur, may under creep loading be as much as 45% less than maximum adhesive strength. Attention is given to test results for the case of titanium-LARC-3 adhesive single-lap specimens.

Sancaktar, E.↗

NASA NTRS2014

Flexural Fillet Geometry Optimization for Design of Force Transducers Used in Aeronautics Testing

Force transducer designs used in the ground testing aeronautics community have seen minimal change over the last few decades. With increased focus on data quality and long- term performance capabilities over the life of these instruments, it is critical to investigate new methods that improve these designs. One area of focus in the past few years at NASA has been on the design of the exural elements of traditional force balance transducers. Many of the heritage balances that have been heavily used over the last few decades have started to develop fatigue cracks. The recent focus on the exural design of traditional single-piece force balances revolves around the design of these elements such that stress concentrations are minimized, with the overall goal of increasing the fatigue life of the balance. Recent research in the area of using conic shaped llets in the highly stressed regions of traditional force balances will be discussed, with preliminary numerical and experimental data results. A case study will be presented which discusses integration of this knowledge into a new high-capacity semi-span force balance

Lynn, Keith C.↗

NASA NTRS2015

Flexural Fillet Geometry Optimization for Design of Force Transducers Used in Aeronautics Testing

Force transducer designs used in the ground testing aeronautics community have seen minimal change over the last few decades. With increased focus on data quality and long-term performance capabilities over the life of these instruments, it is critical to investigate new methods that improve these designs. One area of focus in the past few years at NASA has been on the design of the flexural elements of traditional force balance transducers. Many of the heritage balances that have been heavily used over the last few decades have started to develop fatigue cracks. The recent focus on the flexural design of traditional single-piece force balances revolves around the design of these elements such that stress concentrations are minimized, with the overall goal of increasing the fatigue life of the balance. Recent research in the area of using conic shaped fillets in the highly stressed regions of traditional force balances will be discussed, with preliminary numerical and experimental data results. A case study will be presented which discusses integration of this knowledge into a new high-capacity semi-span force balance.

Lynn, Keith C.↗

NASA NTRS1974

Combined bending-torsion fatigue reliability of AISI 4340 steel shafting with K sub t = 2.34

Results generated by three, unique fatigue reliability research machines which can apply reversed bending loads combined with steady torque are presented. Six-inch long, AISI 4340 steel, grooved specimens with a stress concentration factor of 2.34 and R sub C 35/40 hardness were subjected to various combinations of these loads and cycled to failure. The generated cycles-to-failure and stress-to-failure data are statistically analyzed to develop distributional S-N and Goodman diagrams. Various failure theories are investigated to determine which one represents the data best. The effect of the groove and of the various combined bending-torsion loads on the S-N and Goodman diagrams are determined. Three design applications are presented. The third one illustrates the weight savings that may be achieved by designing for reliability.

Kececioglu, D.↗

NASA NTRS1976

A metal sheet stiffened by a partially debonded composite quarter-plate

An isotropic sheet stiffened by means of an orthotropic quarter-plate is considered. The quarter-plate is assumed to be perfectly bonded to the metal sheet everywhere except an area of debonding which may develop due to high stress concentrations. The adhesive which has a small constant thickness is treated as a shear spring. The loads are applied at infinity and supposed to be transmitted through the metal plate. Shear stress distribution between the two plates was obtained from the continuity of displacements along an area where they were bonded to each other.

Arin, K.↗