Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAMP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Constellation Program Electrical Ground Support Equipment Research and Development

At the Kennedy Space Center, I engaged in the research and development of electrical ground support equipment for NASA's Constellation Program. Timing characteristics playa crucial role in ground support communications. Latency and jitter are two problems that must be understood so that communications are timely and consistent within the Kennedy Ground Control System (KGCS). I conducted latency and jitter tests using Alien-Bradley programmable logic controllers (PLCs) so that these two intrinsic network properties can be reduced. Time stamping and clock synchronization also play significant roles in launch processing and operations. Using RSLogix 5000 project files and Wireshark network protocol analyzing software, I verified master/slave PLC Ethernet module clock synchronization, master/slave IEEE 1588 communications, and time stamping capabilities. All of the timing and synchronization test results are useful in assessing the current KGCS operational level and determining improvements for the future.

McCoy, Keegan S.↗

Low Pressure Flame Blowoff from the Forward Stagnation Region of a Blunt-Nosed Cast PMMA Cylinder in Axial Mixed Convective Flow

Low-pressure blowoff experiments were conducted with a stagnation flame stabilized on the forward tip of cast PMMA rods in a vertical wind tunnel. Pressure, forced flow velocity, gravity, and ambient oxygen concentration were varied. Stagnation flame blowoff is determined from a time-stamped video recording of the test. The blowoff pressure is determined from test section pressure transducer data that is synchronized with the time stamp. The forced flow velocity is also determined from the choked flow orifice pressure. Most of the tests were performed in normal gravity, but a handful of microgravity tests were also conducted to determine the influence of buoyant flow velocity on the blowoff limits. The blowoff limits are found to have a linear dependence between the partial pressure of oxygen and the total pressure, regardless of forced flow velocity and gravity level. The flow velocity (forced and/or buoyant) affects the blowoff pressure through the critical Damkohler number residence time, which dictates the partial pressure of oxygen at blowoff. This is because the critical stretch rate increases linearly with increasing pressure at low pressure (sub-atmospheric pressures) since a second-order overall reaction rate with two-body reactions dominates in this pressure range.

flammability↗

A Prognostic Launch Vehicle Probability of Failure Assessment Methodology for Conceptual Systems Predicated on Human Causal Factors

Create an improved method to calculate reliability of a conceptual launch vehicle system prior to fabrication by using historic data of actual root causes of failures. While failures have unique "proximate causes", there are typically a finite amount of common "root causes". Heretofore launch vehicle reliability evaluation typically hardware-centric statistical analyses, while most root causes of failures are been shown to be human-centric. A method based on human-centric root causes can be used to quantify reliability assessments and focus proposed actions to mitigate problems. Existing methods have been optimistic in their projections of launch vehicle reliability compared to actuals. Hypothesis: reliability of a conceptual launch vehicle can be more accurately evaluated based on a rational, probabilistic approach using past failure assessment teams' findings predicated on human-centric causes."Human Reliability Analysis Methods Selection Guidance for NASA"Chandler F.T., et al., NASA HQ/OSMA study group, July 2006. Outside HRA experts from academia, other federal labs, and the private sector. 50 system reliability methods considered, fourteen selected for further study, four finally selected as best suited for human spaceflight. Probabilistic Risk Analysis (PRA) + Human Reliability Analysis (HRA) enabled incorporating effects and probabilities of human errors. While four down-selected methods deemed appropriate for failure assessment, it did not appear that these methods could be concisely applied to perform major system-wide assessment of probability of failure of a conceptual design without becoming unwieldy."Engineering a Safer World", Detailed, comprehensive study external to NASA Leveson N. G., MIT, 2011.Systems-Theoretic Accident Model and Processes (STAMP). All-encompassing accident model based on systems theory analyzed accidents after they occurred and created approaches to prevent occurrence in developing systems not focused on failure prevention per se, but rather reducing hazards by influencing human behavior through use of constraints, hierarchical control structures, and process models to improve system safetySystem Theoretic Process Analysis (STPA) addresses predictive part of problem (a "hazard analysis"). Includes all causal factors identified in STAMP: "...design errors, software flaws, component interaction accidents, cognitively complex human decision-making errors, and social organizational and management factors contributing to accidents" can guide design process rather than require it to exist before-hand did not appear capable of concise application for system-wide assessment of probability of failure of a conceptual design without becoming unwieldy.

Williams, Craig H.↗

In-situ Testing to Acquire HR-EBSD and DIC Strain Data Within a Coincident Domain

For this project, an inked rubber stamp was applied to a small Inconel 625 specimen. The stamp transferred a thin pattern with microscale features for digital image correlation (DIC). The pattern is easily visible at lower voltages and thin enough to not obstruct backscattered electrons. The unique characteristics of the pattern enabled the concurrent acquisition of DIC and high-resolution electron backscatter diffraction (HR-EBSD) data while the specimen was loaded in-situ. The challenges of in-situ testing and combining EBSD with DIC measurements are discussed. By combining the elastic strains (from HR-EBSD) and total strains (from DIC) the result of this approach is an estimate of stress- strain behavior at points across the specimen surface. This combined dataset can then be used as higher-fidelity data in the calibration of crystal plasticity models.

Will Gilliland↗

Thermoplastic Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

Thermoplastic Composite Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

Improving Compressed Air Energy Efficiency in Automotive Plants - Practical Examples and Implementation

The automotive industry is the largest industry in the United States in terms of the dollar value of production [1]. U.S. automakers face tremendous pressure from foreign competitors, which have an increasing manufacturing presence in this country. The Big Three North American Original Equipment Manufacturers (OEMs) General Motors, Ford, and Chrysler are reacting to declining sales figures and economic strain by working more efficiently and seeking out opportunities to reduce production costs without negatively affecting the production volume or the quality of the product. Successful, cost-effective investment and implementation of the energy efficiency technologies and practices meet the challenge of maintaining the output of high quality product with reduced production costs. Automotive stamping and assembly plants are typically large users of compressed air with annual compressed air utility bills in the range of $2M per year per plant. This paper focuses on practical methods that the authors have researched, analyzed and implemented to improve compressed air system efficiency in automobile manufacturing facilities. It describes typical compressed air systems in automotive stamping and assembly plants, and compares these systems to best practices. The paper then presents a series of examples, organized using the method of inside-out approach, which strategically identifies the energy savings in the compressed air system by first minimizing end-use demand, then minimizing distribution losses, and finally making improvements to primary energy conversion equipment, the air compressor plant.

Implementation of Compressed Air Reduction Project↗

Multiscale spectral nanoscopy

A system and method for non-invasively tracking a particle in a sample is disclosed. The system includes a 2-photon or confocal laser scanning microscope (LSM) and a particle-holding device coupled to a stage with X-Y and Z position control. The system also includes a tracking module having a tracking excitation laser, X-Y and Z radiation-gathering components configured to detect deviations of the particle in an X-Y and Z directions. The system also includes a processor coupled to the X-Y and Z radiation gathering components, generate control signals configured to drive the stage X-Y and Z position controls to track the movement of the particle. The system may also include a synchronization module configured to generate LSM pixels stamped with stage position and a processing module configured to generate a 3D image showing the 3D trajectory of a particle using the LSM pixels stamped with stage position.

42 ENGINEERING↗

RatCAP Time to Digital Converter and Signal Processing module (TSPM)

The TSPM receives and processes ASIC signals and transmits processed data over to the PC using an Ethernet cable. The data is given a location and a time stamp. This is the heart of the device as it gathers and stamps the timing and location of events on each of the ASICs. The five files for the TSPM are needed to manufacture Pet scanners that are based on the RatCAP (Rat Conscious Animal PET). They include a TSPM schematic, a raw data file to build the RatCAP TSPM, an output file that along with the assay file is used by an assembly house to build the RatCAP TSPM, an assay file that provides the part list and XY location for the components that go on the RatCAP TSPM, firmware that includes the source code to program the FPGA, and a realized program on the TSPM based on the firmware.

Fried, Jack↗

Burst resistant thin wall heat sink

An apparatus for cooling an electronic component has a planar top member of a thermal energy conductive material and a parallel planar bottom member of the material, the planar bottom member including a surface having regions configured for heat exchange contact with the electronic component. The planar top member has a plurality of stamped indent formations at a plurality of locations, each indent formation providing a contact surface such that the planar top member is affixed to the bottom member by braze or solder at each contact surface. Alternatively, the planar bottom member also has a plurality of stamped indent formations in alignment with indent formations of the top member. The planar top member is affixed to the bottom member by brazing or soldering each respective contact surface of an indent formation of the planar top member to an opposing contact surface of a corresponding indent formation of the parallel planar bottom member.

42 ENGINEERING↗

Interconnect for fuel cell stack

A metal interconnect for a fuel cell stack is formed from an electrically conductive metal sheet having at least four stamped slots through the metal sheet, and often many more than four slots. The stamped slots individually extend lengthwise parallel to the direction of fluid flow during operation of the fuel cell stack assembly and are disposed on the metal sheet in a pattern extending parallel and perpendicular to the direction of fluid flow, so as to define at least one metal strip portion between adjacent slots extending parallel to the direction of fluid flow and at least one metal strip portion between adjacent slots extending perpendicular to the direction of fluid flow. The metal strip portion(s) include portions of reduced thickness that allow for fluid flow between adjacent slots and portions of greater thickness that provide discrete locations of electrical connection between the separator plate fuel cell electrode.

30 DIRECT ENERGY CONVERSION↗

Porous nanomaterials having three-dimensional patterning

Provided are methods for imprinting a porous material, the methods including applying a first stamp to a porous material having an average pore size of less than about 100 μm, the first stamp having at least a first portion having a first height, a second portion having a second height and a third portion having a third height, wherein the first height, second height and third height are different.

Weiss, Sharon M.↗

Burst resistant thin wall heat sink

An method for forming a cooling apparatus for cooling an electronic component. The apparatus has a planar top member of a thermal energy conductive material and a parallel planar bottom member of the material, the planar bottom member including a surface having regions configured for heat exchange contact with the electronic component. The planar top member has a plurality of stamped indent formations at a plurality of locations, each indent formation providing a contact surface such that the planar top member is affixed to the bottom member by braze or solder at each contact surface. Alternatively, the planar bottom member also has a plurality of stamped indent formations in alignment with indent formations of the top member. The planar top member is affixed to the bottom member by brazing or soldering each respective contact surface of an indent formation of the planar top member to an opposing contact surface of a corresponding indent formation of the parallel planar bottom member.

Coteus, Paul W.↗

High-Speed Friction-Stir Welding To Enable Aluminum Tailor-Welded Blanks

Current joining technologies for automotive aluminum alloys are utilized in low-volume and niche applications, and have yet to be scaled for the high-volume vehicle market. This study targeted further weight reduction, part reduction, and cost savings by enabling tailor-welded blank technology for aluminum alloys at high-volumes. While friction stir welding has been traditionally applied at linear velocities less than one meter per minute, high volume production applications demand the process be extended to higher velocities more amenable to cost sensitive production environments. Unfortunately, weld parameters and performance developed and characterized at low to moderate welding velocities do not directly translate to high speed linear friction stir welding. Therefore, in order to facilitate production of high volume aluminum welded components, parameters were developed with a minimum welding velocity of three meters per minute. With an emphasis on weld quality, welded blanks were evaluated for post-weld formability utilizing a combination of numerical and experimental methods. Evaluation across scales was ultimately validated by stamping full-size production door inner panels made from dissimilar thickness aluminum tailor-welded blanks, which provided validation of the numerical and experimental analysis of laboratory scale tests.

aluminum↗

Microfabrication of plastic-PDMS microfluidic devices using polyimide release layer and selective adhesive bonding

In this study, we present an improved method to bond poly(dimethylsiloxane) (PDMS) with polyimide (PI) to develop flexible substrate microfluidic devices. The PI film was separately fabricated on a silicon wafer by spin coating followed by thermal treatment to avoid surface unevenness of the flexible substrate. In this way, we could also integrate flexible substrate into standard micro-electromechanical systems (MEMS) fabrication. Meanwhile, the adhesive epoxy was selectively transferred to the PDMS microfluidic device by a stamp-and-stick method to avoid epoxy clogging the microfluidic channels. To spread out the epoxy evenly on the transferring substrate, we used superhydrophilic vanadium oxide film coated glass as the transferring substrate. After the bonding process, the flexible substrate could easily be peeled off from the rigid substrate. Contact angle measurement was used to characterize the hydrophicity of the vanadium oxide film. X-ray photoelectron spectroscopy analysis was conducted to study the surface of the epoxy. We further evaluated the bonding quality by peeling tests, which showed a maximum bonding strength of 100 kPa. By injecting with black ink, the plastic microfluidic device was confirmed to be well bonded with no leakage for a day under 1 atm. Finally, this proposed versatile method could bond the microfluidic device and plastic substrate together and be applied in the fabrication of some biosensors and lab-on-a-chip systems.

42 ENGINEERING↗

Time-resolved ion imaging at free-electron lasers using TimepixCam

In this paper, the application of a novel fast optical-imaging camera, TimepixCam, to molecular photoionization experiments using the velocity-map imaging technique at a free-electron laser is described. TimepixCam is a 256 × 256 pixel CMOS camera that is able to detect and time-stamp ion hits with 20 ns timing resolution, thus making it possible to record ion momentum images for all fragment ions simultaneously and avoiding the need to gate the detector on a single fragment. This allows the recording of significantly more data within a given amount of beam time and is particularly useful for pump–probe experiments, where drifts, for example, in the timing and pulse energy of the free-electron laser, severely limit the comparability of pump–probe scans for different fragments taken consecutively. Finally, in principle, this also allows ion–ion covariance or coincidence techniques to be applied to determine angular correlations between fragments.

47 OTHER INSTRUMENTATION↗

Soil Temperature and Moisture Profiles

The STAMP "Soil Temperature and Moisture Profiles" is the replacement Instrument for the SWATS containing the following measuremnts: Soil Specific Soil Water Content Plant Water Availability Total Plant Water Availability Soil Temperature Loam Soil Water Content Soil Conductivity Real Dielectric Permittivity

54 ENVIRONMENTAL SCIENCES↗

Microfabricated systems and assays for studying the cytoskeletal organization, micromechanics, and motility patterns of cancerous cells

Cell motions are driven by coordinated actions of the intracellular cytoskeleton – actin, microtubules (MTs) and substrate/focal adhesions (FAs). This coordination is altered in metastatic cancer cells resulting in deregulated and increased cellular motility. Microfabrication tools, including photolithography, micromolding, microcontact printing, wet stamping and microfluidic devices have emerged as a powerful set of experimental tools with which to probe and define the differences in cytoskeleton organization/dynamics and cell motility patterns in non-metastatic and metastatic cancer cells. In this paper, we discuss four categories of microfabricated systems: (i) micropatterned substrates for studying of cell motility sub-processes (for example, MT targeting of FAs or cell polarization); (ii) systems for studying cell mechanical properties, (iii) systems for probing overall cell motility patterns within challenging geometric confines relevant to metastasis (for example, linear and ratchet geometries), and (iv) microfluidic devices that incorporate co-cultures of multiple cell types and chemical gradients to mimic in vivo intravasation/extravasation steps of metastasis. Finally, together, these systems allow for creating controlled microenvironments that not only mimic complex soft tissues, but are also compatible with live cell high-resolution imaging and quantitative analysis of single cell behavior.

59 BASIC BIOLOGICAL SCIENCES↗