Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAGNATION PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Aerodynamic characteristics of an F-8 aircraft configuration with a variable camber wing at Mach numbers from 0.70 to 1.15

A 0.1-scale model of an F-8 aircraft was tested in the Ames 14-Foot Transonic Wind Tunnel at Mach numbers from 0.7 to 1.15. Angle of attack was varied from -2 deg. to 22 deg. at sideslip angles of 0 deg and -5 deg. Reynolds number, dictated by the atmospheric stagnation pressure, varied with Mach number from 3.4 to 4.0 million based on mean aerodynamic chord. The model was configured with a wing designed to simulate the downward deflection of the leading and trailing edges of an advanced-technology-conformal-variable camber wing. This wing was also equipped with conventional (simple hinge) flaps. In addition, the model was tested with the basic F-8 wing to provide a reference for extrapolating to flight data. In general, at all Mach numbers the use of conformal flap deflections at both the leading edge and trailing edge resulted in slightly higher maximum lift coefficients and lower drag coefficients than with the use of simple hinge flaps. There were also found to be small improvements in the pitching-moment characteristics with the use of conformal flaps.

Boltz, F. W.↗
NASA NTRS1978

Methods used for Space Shuttle SRB thrust shape design

Optimization of the Space Shuttle trajectory is discussed with reference to the low acceleration profile required for Shuttle missions. Static tests of the nominal flight curve are described in terms of impulse requirements, vacuum thrust, and burn time. Attention is given to BARF (Burning Anomaly Rate Factor), and it is noted that mandrel fabrication is intended to include the flexibility to counter BARF, should it occur. Test results are presented in which both BARF and specific impulse are considered as independent variables. It was found that no erosive burning occurred, BARF did not occur, specific impulse was on the order of 265 sec, and flow anomalies in the star region produced head-to-aft stagnation pressure drops in excess of theoretical predictions. In other areas, good agreement is noted between theoretical prediction and empirical data.

Baker, J.↗
NASA NTRS1979

A new flow model for highly separated airfoil flows at low speeds

An analytical model for separated airfoil flows is presented which is based on experimentally observed physical phenomena. These include a free stagnation point aft of the airfoil and a standing vortex in the separated region. A computer program is described which iteratively matches the outer potential flow, the airfoil turbulent boundary layer, the separated jet entrainment, mass conservation in the separated bubble, and the rear stagnation pressure. Separation location and pressure are not specified a priori. Results are presented for surface pressure coefficient and compared with experiment for three angles of attack for a GA(W)-1, 17% thick airfoil.

Zumwalt, G. W.↗
NASA NTRS1979

A study of density measurements in hypersonic helium tunnels using an electron beam fluorescence technique

A series of experiments have been conducted at Langley Research Center to determine the feasibility of using electron-beam fluorescence to measure the free-stream static density of gaseous helium flow over a wide range of conditions. These experiments were conducted in the Langley hypersonic helium tunnel facility and its 3-inch prototype. Measurements were made for a range of stagnation pressures and temperatures and produced free-stream number densities of 1.53 x 10 to the 23rd to 1.25 x 10 to the 24th molecules/cu m and static temperatures from 2 K to 80 K. The results showed the collision quenching cross section to be 4.4 x 10 to the -15th sq cm at 1 K and to have a weak temperature dependence of T to the 1/6. With knowledge of these two values, the free-stream number density can be measured quite accurately.

Honaker, W. C.↗
NASA NTRS1979

Development of the cryogenic tunnel concept and application to the US National Transonic Facility

A fan-driven, high Reynolds number, transonic cryogenic wind tunnel is described. The tunnel has a 2.5- by 2.5 m test section and is capable of operating from ambient to cryogenic temperatures at stagnation pressures up to 8.8 atm. An overview of the cryogenic concept and discussions of drive power requirements, support systems, and operating characteristics and performance of the wind tunnel are included.

Kilgore, R. A.↗
NASA NTRS1980

Wind tunnel investigation of an all flush orifice air data system for a large subsonic aircraft

The results of a wind tunnel investigation on an all flush orifice air data system for use on a KC-135A aircraft are presented. The investigation was performed to determine the applicability of fixed all flush orifice air data systems that use only aircraft surfaces for orifices on the nose of the model (in a configuration similar to that of the shuttle entry air data system) provided the measurements required for the determination of stagnation pressure, angle of attack, and angle of sideslip. For the measurement of static pressure, additional flush orifices in positions on the sides of the fuselage corresponding to those in a standard pitot-static system were required. An acceptable but less accurate system, consisting of orifices only on the nose of the model, is defined and discussed.

Larson, T. J.↗
NASA NTRS1980

Theoretical study of nonadiabatic boundary-layer stabilization times in a cryogenic wind tunnel for typical stainless steel wing and fuselage models

The time varying effect of nonadiabatic wall conditions on boundary layer properties was studied for a two dimensional wing section and an axisymmetric fuselage. The wing and fuselage sections are representative of the wing root chord and fuselage of a typical transport model for the National Transonic Facility. The analysis was made with a solid wing and three fuselage configurations (one solid and two hollow with varying skin thicknesses) all made from AISI type 310S stainless steel. The displacement thickness and local skin friction were investigated at a station on the model in terms of the time required for these two boundary layer properties to reach an adiabatic wall condition after a 50 K step change in total temperature. The analysis was made for a free stream Mach number of 0.85, a total temperature of 117 K, and stagnation pressures of 2, 6, and 9 atm.

Johnson, C. B.↗
NASA NTRS1980

A study of nonadiabatic boundary-layer stabilization time in a cryogenic tunnel for typical wing and fuselage models

A theoretical study has been made of the time varying effect of nonadiabatic wall conditions on boundary layer properties for a two-dimensional wing section and an axisymmetric body of revolution typical of a fuselage. The wing section and body of revolution are representative of the root chord and fuselage of what is considered to be a typical size transport model for the National Transonic Facility. The transient analysis was made at a Mach number of 0.85, for stagnation pressures of 2, 6, and 9 atmospheres at several cryogenic values of total temperature for a solid wing and for three different fuselage skin thickness configurations. The analysis considered wing and fuselage sections made from stainless steel, beryllium copper, and aluminum. Examples are presented that may be used to determine the time required to reach an adiabatic condition after a change in total temperature.

Johnson, C. B.↗
NASA NTRS1980

Techniques for aerodynamic and turbulence measurements in turbomachinery rotors

Nonoptical techniques currently used to measure flows in turbomachine rotors are reviewed, with particular reference to the measurement of the three-dimensional mean velocity, turbulence intensity, Reynolds stresses, static and stagnation pressures, and blade surface measurements. The high level of sophistication of rotor flow measurement techniques is demonstrated. Rotating probe measurements are well suited for low- and moderate-speed turbomachinery, while stationary quick-response probes (hot-wire and pressure probes) are applicable both in low- and high-speed turbomachines. Hot-wire probes, blade pressure transducers, and telemetry systems will provide the urgently needed basic information on steady and unsteady flow through a blade passage, including blade boundary layer, shock configuration, leakage and secondary flows.

Lakshminarayana, B.↗
NASA NTRS1980

Conventional probes for the relative flow measurement in a rotor blade passage

This paper reports the measurement of the relative flow in the rotor blade passages of an axial flow compressor and an axial flow inducer using conventional probes such as five-hole, disc and the spherical pitot-static probes. The probe provides an inexpensive, yet accurate, method of deriving the three dimensional flow field in a rotor. The disc probe is suitable for the blade boundary layer measurement and the pitot-static probe for the static and stagnation pressures and the total velocity across the rotor passage. Typical data obtained from each of these probes demonstrate the complex nature of turbomachinery rotor flow.

Sitaram, N.↗
NASA NTRS1981

Description of recent changes in the Langley 6- by 28-inch transonic tunnel

Calibrations were obtained in the Langley 6 by 28-inch transonic tunnel with newly installed controllable reentry flaps and test section floor and ceiling. Using available theory, the top and bottom slotted walls were redesigned for minimum wind tunnel interference errors of blockage and stream-line curvature. To minimize Mach number gradients along the tunnel axis downstream of the model, controllable flaps were installed to regulate the flow reentering the test section through the slotted walls. The flap setting is independent of stagnation pressure and varies only with Mach number. The freestream Mach number is determined from the pressrue measured at a station 66.04 cm upstream of the model station. The model has no significant influence on the vertical Mach number distribution at this station. This method of Mach number determination appears to be more accurate than one using the plenum pressure.

Sewall, W. G.↗
NASA NTRS1980

Inlet flow distortion in turbomachinery

A single stage axial compressor with distorted inflow is studied. The inflow distortion occurs far upstream and may be a distortion in stagnation temperature, stagnation pressure or both. The blade rows are modeled as semi-actuator disks. Losses, quasi-steady deviation angles, and reference incidence correlations are included in the analysis. Both subsonic and transonic relative Mach numbers are considered. A parameter study is made to determine the influence of such variables as Mach number and swirl angle on the attenuation of the distortion.

Seidel, B. S.↗
NASA NTRS1981

Measurement of recovery temperature on an airfoil in the Langley 0.3-m transonic cryogenic tunnel

Experimental measurements of recovery temperature were made on an airfoil in the Langley 0.3-m Transonic Cryogenic Tunnel at Mach numbers of 0.60 and 0.84 over a Reynolds number per meter range from about 15,000,000 to about 335,000,000. The measured recovery temperatures were considerably below those associated with ideal-gas ambient temperature wind tunnels. This difference was accentuated as the stagnation pressure increased and the total temperature decreased. A boundary-layer code modified for use with cryogenic nitrogen adequately predicted the measured adiabatic wall temperature at all conditions. A quantitative, on-line assessment of the nonadiabatic condition of a model can be made during the operation of a cryogenic wind tunnel by using a correlation for the adiabatic wall temperature which is only a function of total temperature, total pressure, and local Mach number on the model.

Johnson, C. B.↗
NASA NTRS1982

Recent developments in transonic Euler flow over a circular cylinder

Numerical solutions to the Euler equations for transonic flow over a circular cylinder suggest that the inviscid flow separates ahead of the rear stagnation point. The present understanding of this phenomenon and various solutions presented at a workshop on this subject are discussed. All the evidence suggests that inviscid separation is a feature of the Euler equations induced by vorticity and/or stagnation pressure loss in the flow. The possibility of multiple solutions suggested by Hafez (1981) and the oscillatory behavior for the full circle observed by Steger (1977) are seen as needing further investigation.

Salas, M. D.↗
NASA NTRS1983

Aerodynamic force measurements with a strain-gage balance in a cryogenic wind tunnel

Aerodynamic force measurements on a generalized 75 deg delta wing model with sharp leading edges were made with a three component internal strain gage balance in a cryogenic wind tunnel at stagnation temperatures of 300 K, 200 K, and 110 K. The feasibility of using a strain gage balance without thermal control in a cryogenic environment as well as the use of electrical resistance heaters, an insulator between the model and the balance, and a convection shield on the balance was investigated. Force and moment data on the delta wing model as measured by the balance are compared at the different temperatures while holding constant either the Reynolds number or the tunnel stagnation pressure. Tests were made at Mach numbers of 0.3 and 0.5 and at angles of attack up to 29 deg. The results indicate that it is feasible to acquire accurate force and moment data while operating at steady state thermal conditions in a cryogenic wind tunnel, either with or without electrical heaters on the balance. Within the limits of the balance accuracy, there were no apparent Reynolds number effects on the aerodynamic results for the delta wind model.

Boyden, R. P.↗
NASA NTRS1984

High temperature performance of flexible thermal protection materials

Aero convective tests of several flexible thermal protection system (FTPS) concepts were conducted in the NASA Ames Research Center 20 MW arcjet aero heating wind tunnel. The concepts consisted of quilted insulation blankets with nextel AB312 felt insulation stitched between cover cloths with AB312 thread. The cover cloths were commercially available nextel AB312 and nicalon fabrics. The specimens were subjected to convective heat fluxes ranging from 7 to 35 Btu/per sq ft per sec at stagnation pressures of .005 to .02 atm. Specimens were tested both with and without transpiration cooling. Results indicated that both the nextel and nicalon fabrics offer the potential for higher temperature applications than current FTPS, and nicalon appears to be capable of withstanding temperatures well above 2500 degrees F with minimal degradation.

Savage, R. T.↗
NASA NTRS1985

Solar wind stagnation near comets

The nature of the solar wind flow near comets is examined analytically in this paper. In particular, typical values for the stagnation pressure and magnetic barrier strength are estimated, taking into account magnetic field line tension and change-exchange cooling of the mass-loaded solar wind. A knowledge of the strength of the magnetic barrier is required in order to determine the location of the ionopause surface which separates the contaminated solar wind plasma from the outflowing plasma of the cometary ionosphere.

Galeev, A. A.↗
NASA NTRS1986

Theoretical and experimental investigation of the destruction of graphites in a flow of dissociated air

A method is presented for calculating the heating and erosion of blunt bodies made of graphite in a high-enthalpy flow of dissociated air, assuming chemical equilibrium on the surface and taking account of the thermal effects of combustion and sublimation of graphite. The analysis involves the use of a finite difference scheme to solve an equation of unsteady heat conduction. Attention is given to the equilibrium vaporization of C, C2 and C3 molecules. The calculations agree well with experimental data for a wide range of temperatures and stagnation pressures.

Bovina, T. A.↗