Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHROUDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Full-scale Investigation of Cooling Shroud and Ejector Nozzle for a Turbojet Engine : Afterburner Installation

A full-scale ejector cooling investigation was made on a turbojet engine - afterburner installation in the NACA Lewis altitude wind tunnel. Ejector performance was studied at primary exhaust-gas temperatures from 2700 degrees to 3400 degrees R (corresponding to ejector temperature ratios from 2.0 to 5.0), primary pressure ratios from 1.79 to 3.4, secondary air flows up to 29 percent of the primary gas flow, and for diameter ratios from 1.08 to 1.42 and spacing ratios from 0.04 to 1.16. In addition, variations were made in the primary exhaust-nozzle area. Ejectors with large diameter ratios permit the attainment of high gas flow ratios, but the jet-thrust losses become prohibitive as the spacing ratio is increased from 0 to 0.16. As the ejector diameter is reduced, the obtainable gas-flow ratio and the thrust loss are reduced. Previous results showing that data obtained at a temperature ratio of 1.0 could not be extrapolated to determine ejector performance at high temperature ratios by the application of the temperature ratio factor to the gas-flow ratios are substantiated by the present investigation.

AFTERBURNERS↗

A Flexure-Based Mechanism for Precision Adjustment of National Ignition Facility Target Shrouds in Three Rotational Degrees of Freedom

This study presents the design of a flexure-based mount allowing adjustment in three rotational degrees of freedom (DOFs) through high-precision set-screw actuators. The requirements of the application called for small but controlled angular adjustments for mounting a cantilevered beam. The proposed design is based on an array of parallel beams to provide sufficiently high stiffness in the translational directions while allowing angular adjustment through the actuators. A simplified physical model in combination with standard beam theory was applied to estimate the deflection profile and maximum stresses in the beams. A finite element model was built to calculate the stresses and beam profiles for scenarios in which the flexure is simultaneously actuated in more than one DOF.

3 DOF↗

Transient Adjustments for Metal-Sheathed Thermocouples on Metal Plates (Shrouds)

This report provides guidance on how to adjust temperature measurements from mineral-insulated, metal-sheathed (MIMS) thermocouples (TCs) mounted on metal plates to correct for slow transient response. This information is needed so that more accurate transient temperature measurements can be made. These more accurate temperature measurements are of benefit for both qualification of hardware and as data sets for model validation. The approach was to use a relatively simple first order adjustment to the MIMS TC reading, as compared to a more accurate metal plate temperature measurement. MIMS TCs are used to improve reliability. Results from four data sets were analyzed to determine the time constraint; an overall average of 5.0 s was obtained.

42 ENGINEERING↗

Internal performance of a 10 deg conical plug nozzle with a multispoke primary and translating external shroud

An experimental investigation was conducted in a nozzle static test facility to determine the performance characteristics of a cold-flow, 21.59-centimeter-diameter plug nozzle with a multispoke primary. Two multispoke primary nozzles, a 12-spoke and a 24-spoke, were tested and compared with an annular plug nozzle. The supersonic cruise configurations for both spoke primaries performed about the same, with a gross thrust coefficient of 0.974, a decrease of approximately 1.5 percent from the reference nozzle. The takeoff configuration for the 12-spoke primary had a gross thrust coefficient of 0.957, a decrease of 1.5 percent from the reference nozzle, and the 24-spoke primary had a gross thrust coefficient of 0.95.

Bresnahan, D. L.↗

Backswept impeller and vane island diffuser and shroud for NASA advanced-concepts compressor test rig

A centrifugal impeller based on an existing backswept design was defined. In addition, a vaned diffuser was designed to match this impeller and also to be compatible with an existing 6:1 compressor test rig. The mechanical integrity of this design was verified by analysis. Hardware was procured and inspected to insure conformity with design tolerances. An overspeed test was successfully conducted on one of the impellers fabricated under this program.

Perrone, G. L.↗

Shrouded fan propulsors for light aircraft.

Continued growth of general-aviation over the next 10-15 years is dependent upon continuing improvement in aircraft safety, utility, performance, and cost. An attractive, compact, low-noise propulsor concept, the Q-FAN, when matched to reciprocating or rotary combustion engines, opens up the exciting prospect of new, cleaner airframe designs for the next generation of general-aviation aircraft, which will provide these improvements and meet the expected noise and pollution restrictions of the 1980 time period. In this paper, Q-FAN propulsion system performance, weight, noise, and cost trends are discussed. The impact of this propulsion system on the complete aircraft is investigated for two representative aircraft size categories. Examples of conceptual designs for Q-FAN/engine integration and aircraft installations are presented.

Waters, M. H.↗

Wind tunnel investigation of a Centaur standard shroud compartment vent from Mach number of 0.70 to 1.96

An experimental investigation was conducted in the Lewis Research Center 8- by 6-foot supersonic wind tunnel to determine the vent discharge coefficient for the Centaur standard shroud/liquid hydrogen tank compartment vent. The test was conducted from Mach 0.70 to 1.96 with the vent mounted in a flat plate. Full scale simulated flight hardware, such as the vent, corrugations, aft field joint ring and ice bag clip was used. Air was discharged from a plenum chamber, located on the tunnel sidewall behind the plate, through five 6.35 cm diameter vent orifices into the free stream. Boundary layer thickeners, analytically predicted displacement thickness for the vehicle nominal flight trajectory could be simulated over the Mach number range. The highest vent discharge coefficient for any given Mach number and vent pressure ratio generally occurred at the maximum displacement thickness.

Johns, A. L.↗

Program to develop sprayed, plastically deformable compressor shroud seal materials

A study of fundamental rub behavior for ten dense sprayed materials and eight current compressor clearance materials has been conducted. A literature survey of a wide variety of metallurgical and thermophysical properties was conducted and correlated to rub behavior. Based on these results, the most promising dense rub material was Cu-9Al. Additional studies on the effects of porosity, incursion rate, blade solidity and ambient temperature were carried out on aluminum bronze (Cu-9Al-1Fe) with and without a 515B Feltmetal underlayer.

Schwab, R. C.↗

Composite wall concept for high temperature turbine shrouds: Survey of low modulus strain isolator materials

Plasma sprayed yttria stabilized zirconium oxide turbine seal specimens, incorporating various low modulus porous metal strain isolator pads between the zirconium oxide and a dense metal substrate, were subjected to cyclic thermal shock testing. Specimens that had a low modulus pad composed of sintered FeNiCrAlY fibermetal survived 1000 thermal shock cycles without spalling of the ceramic. A figure of merit for the low modulus pad materials taking into consideration the elastic modulus, thermal conductivity, strength, and oxidation resistance of the pad was proposed, and showed reasonable agreement with the thermal shock results. A potential surface distress problem on the zirconium oxide, associated with nonuniform temperature distribution and rapid stress relaxation was identified. One approach to solving the surface distress problem through application of laser surface fusion of the zirconium oxide layer showed some promise, but improvements in the laser surface fusion process are necessary to prevent process associated damage to the ceramic.

Bill, R. C.↗

Program to develop sprayed, plastically deformable compressor shroud seal materials

A study of fundamental rub behavior for 10 dense, sprayed materials and eight current compressor clearance materials was conducted. A literature survey of a wide variety of metallurgical and thermophysical properties was conducted and correlated to rub behavior. Based on the results, the most promising dense rub material was Cu-9A1. Additional studies on the effects of porosity, incursion rate, blade solidity, and ambient temperature were carried out on aluminum bronze (Cu-9Al-1Fe) with and without a 515B Feltmetal underlayer. A further development effort was conducted to assess the property requirements of a porous, aluminum bronze, seal material. Strength, thermal cycle capabilities, erosion and oxidation resistance, machinability, and abradability at several porosity levels were examined.

Schell, J. D.↗