Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHRINKAGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Influence of Fiber Orientation on Deformation of Additive Manufactured Composites

Anisotropy caused by flow-induced fiber orientation of discontinuous fibers within the extrudate in the Extrusion Deposition Additive Manufacturing (EDAM) process gives rise to anisotropic shrinkage in printed parts and thereby, final part deformations. Three fiber orientation states, described by the second-order orientation tensor, were investigated to determine their influence upon final geometry. Two material systems were investigated including a short glass fiber-reinforced polyamide and a short carbon fiber-reinforced polyamide. A curvilinear geometry was modeled and printed virtually in the thermo-mechanical simulation, ADDITIVE3D©. The scale of the printed geometry was in the range of 300–400 mm and contained three semicircular geometry regions connected to linear regions, thereby inducing significant magnification of the spring-in deformation. The predicted deformation of the printed geometry for the three fiber orientation states and two material systems were compared. The deformation predicted for glass fiber-filled polyamide and carbon fiber-filled polyamide of the same fiber orientation states showed comparable deformations. In conclusion, the largest residual deformation was shown to correspond to the orientation tensor with the greatest degree of anisotropy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Binder jet additive manufacturing of ceramic heat exchangers for concentrating solar power applications with thermal energy storage in molten chlorides

Triply periodic minimal surface (TPMS) geometries can only be fabricated by additive manufacturing methods and are of interest for heat exchangers. Ceramic TPMS heat exchangers can operate at higher temperatures and pressures with superior performance and increased operating efficiencies compared to metal heat exchangers. The properties of ultra-high temperature ceramic (UHTC) materials are also favorable for heat exchangers and potentially suited to concentrated solar power (CSP) systems, such as those based on a molten chloride salt thermal energy storage (TES) medium used to heat CO 2 in a closed-loop Brayton power cycle. We intended to demonstrate binder jet additive manufacturing feasibility of a UHTC-TPMS structure by printing and sintering a null candidate. We aimed to achieve parts with a relative density ≥ 92 % of theoretical and to provide a TPMS part demonstration. The target density indicates the transition from intermediate to final stage sintering, a requirement to inhibit gas permeability and for sintering complex near net shapes to full density with sinter-HIP technology. The goal of the TPMS part demonstration was to determine if printing and sintering parameters developed from test coupons apply to the complex geometries that will eventually be used in a heat exchanger design. Our objective was to print cubic TPMS parts with a 9 cm 3 volume and sinter it without distorting and cracking. We report we were able to sinter ZrB 2 -MoSi 2 composite parts based on the Schwarz-D TPMS and achieve isotropic shrinkage up to 60 % by volume, resulting in densities ranging from 92 % to 96 % of theoretical.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A coupled hydrologic-agroeconomic modeling framework to evaluate adaptive irrigation strategies under groundwater withdrawal restrictions

Growing groundwater scarcity requires integrated tools to capture interactions among hydrology, agricultural production, markets, and land use. This study presents an iterative modeling framework that couples hydrologic, crop-yield, and economic models to capture two-way feedback among water availability, agricultural production, and market responses under groundwater constraints. The primary goal of this paper is to describe the methodological development of the coupled framework and demonstrate the significance of iterative model interaction. Applied to the western United States, we evaluated adaptive responses to restricting groundwater use beyond recharge levels, represented through changes in irrigation management and expansion or shrinkage of crop markets through land reallocation. Results demonstrate that the iterative coupling converges to stable equilibrium responses within 10 iterations. At equilibrium, deficit irrigation emerges as the dominant adaptation strategy in California, with irrigation levels stabilizing at approximately 70% of full irrigation demand, while Arizona and New Mexico experience stronger yield sensitivities. Early iterations produce commodity price increases of up to 10% for fruit and vegetable crops; however, these responses moderate as land allocation and production patterns adjust across regions. Deficit irrigation and spatial reallocation of irrigated land partially offset production losses, with variability observed across different states: California maintains yields primarily via deficit irrigation, whereas Arizona and New Mexico will rely mainly on reducing irrigated area to absorb the shock. By capturing feedback between biophysical and economic processes, this approach highlights how irrigation strategies and land-use decisions evolve under water stress and provides a transferable platform for evaluating water management policies.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Impact of salinity on morphology, growth, and pigment profiles of Scenedesmus obliquus HTB1 under ambient air and elevated CO 2 (10 %) conditions

Certain microalgal species, such as Scenedesmus obliquus strain HTB1, thrive under high CO 2 concentrations, making them promising for carbon sequestration to mitigate climate change. Isolated from the Baltimore Inner Harbor, HTB1 grows faster with 10 % CO 2 than with ambient air. To investigate its responses to salinity and elevated CO 2 , two experiments were conducted. In the first, HTB1 was cultured at seven different salinities (0, 17.5, 20, 22.5, 25, 27.5, and 30 ppt) (parts per thousand) under ambient air. Higher salinity caused cell shrinkage, color changes from green to pale white, reduced pigments like zeaxanthin, lutein, and chlorophyll b, but increased canthaxanthin. Growth declined significantly above 22.5 ppt. The second experiment compared HTB1's response to salinity (0, 10, 20 ppt) under air and 10 % CO 2 . Cultures under 10 % CO 2 showed minimal color changes, while those under air shifted from green to brown, with salinity having less inhibitory effects on growth under elevated CO 2 . Interestingly, lutein and canthaxanthin levels rose with salinity in 10 % CO 2 . These findings indicate that elevated CO 2 mitigates salt stress in HTB1, reducing its impact on growth and promoting adaptive pigment changes. This study sheds light on how salinity and CO 2 interact to influence HTB1's morphology, growth, and pigment composition, enhancing our understanding of its resilience and potential applications.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Fast response of global monsoon area and precipitation to regional carbonaceous aerosols

Monsoon exerts a significant social and economic impact on billions of people around the world. Changes in global monsoon (GM) rainfall under global warming have been well studied; however, the understanding of GM connection with regional aerosol emissions is limited. Using an atmospheric general circulation model (AGCM), we attempt to quantify the response of global monsoon area and precipitation to the removal of carbonaceous aerosols over North America (AM), North Africa (AF), Europe (EU), and Asia (AS). Response to the emission removal, the global average aerosol optical depths (AOD) are reduced by 2.21%, 1.8%, 1.16%, and 3.8% respectively. Additionally, a southward shift in the GM domain is observed, responding to changes in magnitude and position of the Inter-Tropical Convergence Zone, when carbonaceous aerosols are removed over these regions in the Northern Hemisphere. The percentage departure in the area-averaged GM precipitation is found to be 4-fold in magnitude for the removal of emissions over EU when compared to that of AM and AF. A shrinkage in the GM area is also observed, which is maximum for EU (~-30%) compared to AM and AF (~-25%). The change in GM precipitation and area are found to be the least and opposite in nature for AS emissions. This study provides insight into the regional nature of carbonaceous aerosol effects on global precipitation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Constructing uniform oxygen defect engineering on primary particle level for high-stability lithium-rich cathode materials

Lithium-rich layered cathode materials are considered to be research focus of cathode candidates for next generation lithium-ion batteries due to their high specific capacity and low cost. However, lattice deoxidation associated with elemental migration and internal local shrinkage usually results in deteriorated cyclic performance and notorious voltage attenuation, severely limiting its application. In this paper, we have successfully injected uniform oxygen defects into surface region of Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 primary particles under the high-pressure and weak carbonate environment. Various experimental investigations indicate that the injected robust oxygen defects can not only mitigate detrimental interfacial reactions but also suppress unfavorable lattice variation and particle breakage. More importantly, theoretical calculations unravel the critical roles of oxygen defects in regulating energy band structure for strengthened anionic reversibility. Owing to stabilization effects of unique oxygen defect engineering, the modified Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 cathode has harvested dramatically enhanced electrochemical performance including a high initial coulombic efficiency of 96.6%, an outstanding capacity retention of 91.96% (1C, 200 cycles) and suppressed voltage decay of only 1.62 mV per cycle. Therefore, this facile and effective defect engineering strategy could establish new guidance for promoting practical application of Li-rich Mn-based cathode material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Simultaneous x-ray and neutron 4D tomographic study of drying-driven hydro-mechanical behavior of cement-based materials at moderate temperatures

The drying of cement-based materials is intimately related to their durability, which has significant economic, social and environmental repercussions. The evolution of the saturation of the pore network and the associated drying shrinkage are in fact leading causes of cracking and of the ensuing penetration of aggressive chemicals. This process is highly heterogeneous, due to the thermo-hydric spatial gradients developing in the material from the exposed surfaces to its core and because of local effects, driven by the intrinsically heterogeneous micro-structure (e.g., by the distribution of pores and aggregates). It follows that macroscopic, sample-scale measurements cannot fully disclose the complexity of the underlying processes. In the last few decades, significant advances in full-field techniques have allowed an unprecedented insight into these local processes. For cement-based materials, x-ray and neutron tomography lend themselves as ideal, and highly complementary, tools for the study of their thermo-hydro-mechanical behavior. Notably, the high sensitivity to density variations of x-ray imaging gives access to the developments of fractures, in 4D (3D + time). On the other hand, neutron tomography allows the study of the evolution of the moisture field in 4D, thanks to its high hydrogen sensitivity. The combination of these two techniques provides a unique insight in thermo-hydro-mechanical couplings, e.g., the effect of cracks on the water content field. This contribution presents novel 5D datasets (3D tomographies along time, plus truly simultaneous x-ray and Neutron rapid acquisitions) in-operando of a cement paste and of a concrete sample heated at moderate temperatures (up to 140{sup ∘}C). The analysis of this 5D data-set (once aligned in time and across modalities) allows for example a quantification of the 4D moisture profiles which were found to predict an overall water loss at hydric equilibrium coherent with the corresponding analytical analysis. In the cement paste sample, the x-ray dataset captures the evolution of an extensive cracking network, opening and propagation toward the core of the sample. A novel analysis procedure is here proposed which allows the extraction of these fractures and the analysis of their interplay with local drying as captured through neutron imaging. This for example reveals the depth of penetration of drying in the vicinity of the fractures along time, which is essential for the assessment and calibration of hydro-mechanical coupled models.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The effect of powder feedstock and heat treatment on the thermal and mechanical properties of binder jet printed ZrC

In this study, zirconium carbide (ZrC) disks were fabricated using binder jet printing to study the effect of powder feedstock, print parameters, and heat treatment on flowability and final materials properties. A median volumetric particle size smaller than 10 μm was shown to cause the powder to stop flowing during printing. Disks were printed using ZrC with suitable flowability and then heat-treated at temperatures between 1800°C and 2200°C for 1 or 5h. The density, part shrinkage, thermal diffusivity, and fracture strength all increased with increasing temperature and time. The heat-treated disks were then heated to 2200°C for 5h and the properties converged for disks of the same particle size, indicating the hottest temperature and longest time of exposure dictates the final properties. Lastly, it was shown that larger particles produce lower density materials with worse thermal diffusivity, most likely because of poor connectivity between particles after heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Additive manufacturing of mullite ceramic by digital light processing

Mullite material was successfully additively manufactured using digital light processing (DLP). The printed geometry involves a one-step process of pyrolysis, de-binding, and sintering under a plain atmosphere to achieve an average of 76 % ceramic yield and linear shrinkage of 12 %. Furthermore, the thermal profile was carefully controlled to obtain consistent phases in which the XRD shows a mullite phase. Here, in addition, the Weibull analysis was conducted on the sintered flexural specimens, showing a Weibull modulus (m) of 13.05 with a characteristic strength (σ 0 ) of 94.96 MPa. Synchrotron microtomography was performed on the sintered specimens, which showed two distinct porosity distributions (small and large). Large porosity (non-spherical elongated) is the primary cause of decreased material strength, while small porosity (spherical) is the sintering product. The measured thermal conductivity of the specimens was in the range of 2.7–3.1 W/m∙k and decreased with an increase in temperature. Lastly, large-scale prototypes were printed concurrently with a fine resolution of 25 μm without any compromise on the predetermined design and structure.

Additive manufacturing↗
DOE OSTI2025

Development of direct ink write radially graded alumina/zirconia

Functionally graded materials (FGMs) are of interest in multiple fields, yet many materials combinations are limited by coefficient of thermal expansion (CTE) mismatch. Here, a radially graded alumina/yttria-doped zirconia (Al 2 O 3 /8YZ) FGM is used to demonstrate processing strategies to mitigate CTE and sintering behavior differences between these oxides. FGM materials are especially sensitive to ink stability during printing, as all components (in this case, Al 2 O 3 and 8YZ) must be stabilized in the same dispersant or additive solution. Thus, this system is also ideal to demonstrate ink optimization best practices. Materials were characterized throughout processing to correlate the effects of common additives on both the ceramic particle suspensions and final sintered components. Aggregation observed in the initial additive-containing suspensions were present in the sintered component. The differences in sintering onset temperature and shrinkage rate resulted in internal stresses within the sintered component, which ultimately caused mechanical failure of the component under low stress. In conclusion, a processing strategy was recommended to mitigate the sintering behavior mismatch of alumina and 8 wt% yttria-stabilized zirconia.

Lamm, Benjamin W. [Oak Ridge National Laboratory (↗
DOE OSTI2026

Physicochemical properties of digital light processing 3D-Printed alumina and mullite ceramics

Alumina ceramics fabricated using conventional techniques such as uniaxial pressing or injection molding are popular due to their low density, excellent insulation, and mechanical properties. However, these methods often limit the fabrication of complex geometries with high dimensional accuracy due to tooling constraints and limited design freedom. To overcome these limitations, this study employed Digital Light Processing (DLP) additive manufacturing (AM), which enables the production of precise structures. In addition, the optimization of sintering parameters to enhance the densification and performance of alumina and mullite ceramics was investigated, with a specific focus on how varying sintering temperatures and hold times affect part shrinkage, geometric accuracy, and material integrity. Flexural strength of both alumina and mullite specimens was clearly influenced by the way the layers was stacked. When layers were arranged across the direction of the applied load (Z = 4; XZ), the strength was higher than when they were stacked along the same direction as the load (Z = 3; XY). Weibull analysis based on these results showed high modulus values across all samples, indicating good reliability in the flexural strength measurements. This reliability, combined with the clear influence of sintering parameters, highlights how processing conditions effect the material properties and mechanical performance of parts produced through DLP additive manufacturing. In conclusion, these findings open new avenues for ceramic AM across various applications, enhancing the potential for innovation in fields such as aerospace, biomedical engineering, and energy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Proppant embedment in coal and shale: Impacts of stress hardening and sorption

During methane production in CBM reservoirs, the influence of proppant embedment and permeability damage cannot be neglected – especially where the wall-rock is soft. Effective stresses are elevated during methane recovery, increasing both normal loading stress and confinement and simultaneously overprinting sorption-induced volumetric strains. Experiments and analytic modeling are conducted to define key mechanisms controlling these competitive effects. We independently measure overall sample compaction (external LVDT) and local strain (strain gauge) in the matrix to deconvolve proppant embedment in a propped fracture for different conditions of confining stress. The results show symptomatic behaviors of elastic (shale) and elastoplastic (coal) responses of embedment. Different from shale, the evolution of embedment is convex upwards with increased stress where indented depth increases more rapidly as loading stress increases under constant confinement. In addition, a stress-hardening effect is found to play a pivotal role in determining the characteristics of indentation, which are examined in terms of evolution profiles, deformation regimes, embedment slopes, curvatures, yield points and irreversible indentations. Based on the experimental observations a semianalytical model predicts indentation and the evolution of propped permeability under recreated in-situ stress conditions. A simplified case study is conducted to further illustrate the evolution of aperture and permeability of a propped fracture in CBM reservoirs. The modeling results suggest that proppant embedment is significantly overestimated if the variable stress-hardening (VSH) effect is neglected, especially when effective stress is large. Moreover, a decrease in indentation depth possibly occurs during late stage methane production, resulting in a reversal/recovery in fracture closure. This is because desorption-induced shrinkage becomes the predominant effect, causing an increase in aperture and a reduction in the indented volume of proppant. The resulting recovery in permeability implies that the propped coal fracture has the potential to optimally facilitate methane production as a pathway, even at high closure stresses generated by methane drainage.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Multisublattice cluster expansion study of short-range ordering in iron-substituted strontium titanate

Owing to the challenges in obtaining realistic atomic configurations in large chemical phase spaces, it is not straightforward to describe structure–property relations in materials exhibiting configurational disorder. One example is iron-substituted strontium titanate (SrTi 1–x Fe x O 3–d , STF), a promising perovskite-derivative cathode material in solid oxide fuel cells that exhibits full solid solubility 0 ≤ x ≤ 1 and a tendency to exhibit short-range order. Here we demonstrate a multisublattice cluster expansion (CE) framework and apply it to STF across the full composition range. The CE approach is distinct from more traditional CE formulations in that clusters are defined explicitly by the chemical species distributed among multiple sublattices, rather than via cluster functions of occupation variables with decoration. The modified CE approach makes it easy to distinguish meaningful chemical interactions that are harder to extract from conventional CE, since for the latter chemical identity in a cluster is expressed as a product of site occupations. The least absolute shrinkage and selection operator (LASSO) is implemented as a regression analysis tool to select key clusters and avoid overfitting. We demonstrate this formulation on STF, and show that it can accurately predict configurational energies in comparison to conventional CE. From the key clusters, we identify that short-range ordering between substitutional Fe and oxygen vacancies (V O ) results in the formation of Fe–VO strings. In addition, we consider the stability of STF through CE-based Monte Carlo (MC) simulations and confirm the presence of superstructures that were previously observed in transmission electron microscopy. In this work, analysis of atomic configurations from MC samples reveals variations in the oxidation state of Fe atoms, which can be explained by the ordering tendency of Fe and V O . The cluster description and selection formalism described here may be applied to other disordered multisublattice systems for accurate and efficient material modeling.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Peridynamic modeling of cementitious materials for nuclear waste management

Radioactive and hazardous waste generated from fuel processing plants, nuclear reactors, and hospitals, requires effective management strategies. Cementitious materials are widely applied for these needs, serving as structural materials, reactive barriers, or waste forms. In these applications cracking poses a significant risk to performance, driven by inconsistent shrinkage of the components and the varying strength and permeability of their interfaces. Traditional modeling approaches face challenges in representing the complex fracture behavior of cementitious materials due to the reliance on spatial derivatives and difficulties with mesh generation. Here, to overcome these limitations, we employ peridynamics, a novel continuum mechanics formulation that uses integrals to describe mechanical equilibrium, avoiding discontinuities associated with traditional methods. Through incorporation of a bi-linear softening model and quasistatics, an experimentally validated model for Portland cement concrete samples was created. Mechanical parameters, including compressive strength and elastic modulus were validated and variation due to aggregate packing was evaluated. Additionally, sensitivity analysis of the peridynamic parameters to the bulk material properties was established. The results lay the groundwork for evaluating the impact of unique conditions of cementitious waste forms that can be assessed to improve the reliability of waste management strategies.

Aggregates↗
DOE OSTI2020

Stimuli-responsive petroleum cement composite with giant expansion and enhanced mechanical properties

Shrinkage, as an inherent property of cement during the curing process, has been a concern in the oil & gas industry for centuries. Therefore, expansive cement has been studied for many decades, primarily through incorporation of expansive additives. Nevertheless, traditional expansive additives are not able to achieve the required expansive ratio or maintain a good mechanical property for the cement composite at extreme underground condition. Accordingly, a new generation of expansive additive, which not only has the required expansion, but also work at the downhole high temperature and high pressure environment, and maintain or even enhance the mechanical property, is highly desired. In this work, a high enthalpy storage shape memory polymer (SMP) as a new class of expansive additive is investigated. It is found that the cement composite achieves 1.4% circumferential expansion by only 6% by weight of SMP additives. The compressive strength and flexural strength are also enhanced at the same time, which is hardly achievable by other expansive additives with the same concertation. Good pumpability is also proved by rheological study. The mechanism controlling the enhanced properties is reveled through morphological study and element mapping analysis at the SMP/cement interface.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanically and thermally robust microporous copolymer separators for lithium ion batteries

Next generation, multifunctional separators can enhance energy storage, power, and safety performance of lithium ion batteries but must be simple to fabricate and incorporate with existing roll-to-roll manufacturing. Here, this study presents a strategy to facilely prepare these separators using UV-initiated polymerization-induced phase separation (PIPS), wherein microporous polymer separators are fabricated directly from constituent monomers and ethylene carbonate (EC) porogen. This enables a wide compositional design space as co-monomers with specific chemical functionality can be readily incorporated into the PIPS precursor mixture. Herein, 1,4-butanediol diacrylate (BDDA) was copolymerized with poly(ethylene glycol) diacrylate (PEGDA) to increase the acrylate conversion in the photopolymerization and improve mechanical properties. By tuning the ratio of PEGDA and EC, separators with high porosity (41.3%) and effective ionic conductivity (2.09 mS cm –1 ) were prepared. Inclusion of PEGDA was essential to increasing the elastic modulus to > 345 MPa, which is required for cell assembly by roll-to-roll manufacturing. All separators prepared were shown to enable reversible cycling of lithium metal/LiNi 0.5 Mn 0.3 Co 0.2 O 2 half-cells for 100 cycles. Unlike conventional polyolefin separators, which were shown to melt at 160 °C and shrink by up to 29.8% at elevated temperatures, the PIPS separators possess exceptional, safety-enhancing thermomechanical properties, undergoing no phase transitions or thermal shrinkage.

25 ENERGY STORAGE↗
DOE OSTI2022

Design and performance analysis of a Swirl Pintle injector for a 1 MW th pressurized oxy-coal combustor

Pressurized Oxy-coal combustion has the potential to achieve high thermal efficiency by recovering the latent heat of steam from flue gases and providing options for up to 95% carbon capture. Here, this study proposes a novel burner technology for pressurized oxy-coal combustion and investigates its operability. Three burner versions are designed and tested; no swirl, swirl numbers 0.9 and 1.2 to identify optimum design parameters and performance. A commercially available Dantec Dynamics software is used to conduct the shadowgraph experiments to observe burner performance. Coal water slurry is used as fuel with three different slurry ratios where the coal percentage by weights were 30, 40 and 50. Droplet size, distribution, spray angle and jet breakup lengths are measured and analyzed to quantify the performance. The study found that increasing the swirl number enhanced atomization. Implementing swirlers allowed the jet to spread through faster primary jet separation, thus improving atomization. In addition, higher slurry ratios improved the generation of smaller particles. However, it was also found that excessive increases in oxidizer momentums negatively impact the atomization process by jet shrinkage. The study concluded that operating a pintle burner at 1.2 swirl conditions with a 40/60 slurry ratio produces optimum performance.

42 ENGINEERING↗
DOE OSTI2023

Electrochemical-mechanical coupling failure mechanism of composite cathode in all-solid-state batteries

Composite cathode composed of active particles and solid electrolytes (SEs) can considerably enlarge the particle-SE contact areas and achieve high areal loadings in all-solid-state batteries (ASSBs). However, the challenging interfacial instability and particle damage problems remain unsolved. Herein, we establish a 3D electrochemical-mechanical coupled model to investigate the underlying failure mechanism by considering the governing electrochemical and physics processes. Micro-scale heterogeneous primary particles with random crystallographic orientation and size inside the LiNi 1/3 Co 1/3 Mn 1/3 O 2 (NCM111) secondary particle of the model result in the anisotropic Li diffusion and volume variation within the secondary particle, leading to significant nonuniformity of the Li concentration, and GPa-level stress distributions at primary particle boundaries, and finally causing the particle internal cracks. The particle volume shrinkage under the constraint of stiff Li 7 La 3 Zr 2 O 12 (LLZO) SE triggers the interface debonding (gap>50 nm) with increased interfacial impedance to degrade cell capacity. Higher C-rates result in larger residual stress (~100 MPa)/strain/debonding gap at dis-charging end, more likely to deteriorate the cell performance. Increasing the interfacial strength between the particle and SE can suppress the interface debonding but induces high stress (up to 10 GPa). In conclusion, results reveal the underlying mechanism of the electrochemical-mechanical coupling failure mechanism for composite cathode and provide promising guidance on the further improvement of a more robust composite cathode for ASSBs.

25 ENERGY STORAGE↗