Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHEAR PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Improvement of Al/Steel Tungsten Inert Gas Welding–Brazing Joint by High-Energy Shot Peening

High-energy shot peening treatment was applied to improve the Al/steel tungsten inert gas welding–brazing lap joint. The mechanical properties and microstructure evolution of the joint were investigated. Results showed that the mechanical properties of weld were evidently reinforced due to microstructure transformation of joint surface layer. The grain structure in the joint surface layer was distorted and refined. Large compressive residual stress was introduced into the joint surface, and its hardness obviously increased due to strain hardening. When the peening pressure was 0.15 MPa, the tensile shear strength of the joint reached the maximum value (199.6 MPa), which was 16.5% higher than that of the as-welded joint.

36 MATERIALS SCIENCE↗

Shear Strength at 75 F to 500 F of Fourteen Adhesives Used to Bond a Glass-fabric-reinforced Phenolic Resin Laminate to Steel

Fourteen adhesives used to bond a glass-fabric-reinforced phenolic resin laminate to steel were tested in order to determine their shear strengths at temperatures from 75 F to 500 F. Fabrication methods were varied to evaluate the effect of placing cloth between the facing surfaces to maintain a uniform bond-line thickness. One glass-fabric supported phenolic adhesive was found to have a shear strength of 3,400 psi at 300 F and over 1,000 psi at 500 F. Strength and fabrication data are tabulated for all adhesives tested.

PLASTICS↗

Nanomechanical properties and phase transitions in a double-walled (5,5)-(10,10) carbon nanotube: ab initio calculations

The structure and elastic properties of (5,5) and (10,10) nanotubes, as well as barriers for relative rotation of the walls and their relative sliding along the axis in a double-walled (5,5)-(10,10) carbon nanotube, are calculated using the density functional method. The results of these calculations are the basis for estimating the following physical quantities: ultimate shear strengths and diffusion coefficients for relative sliding along the axis and rotation of the walls, as well as frequencies of relative rotational and translational oscillations of the walls. The commensurability-incommensurability phase transition is analyzed. The length of the incommensurability defect is estimated on the basis of ab initio calculations. It is proposed that a double-walled carbon nanotube be used as a plain bearing. The possibility of experimental verification of the results is discussed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Reliability analysis of the influence of seepage on levee stability

Reliability analysis is used to evaluate the probability of failure of a flood defence embankment subject to a blanket layer foundation condition, where high seepage forces increase the likelihood of internal erosion and slope failure. The stochastic effect of hydraulic conductivity and blanket layer thickness, in addition to soil shear strength properties, is considered for the underseepage and slope stability failure modes using the first-order reliability method. The blanket layer thickness controls the factor of safety (F) and reliability, followed by the unit weight of the blanket layer. Despite variation over orders of magnitude, hydraulic conductivity is less important than and comparable to the effect of soil shear strength parameters. Aleatory uncertainty is evaluated using fragility curves and a confidence interval on the expected value of F (stochastic F). Uncertainty in probability distribution parameters allows quantification of a subset of epistemic uncertainty and is used to construct confidence intervals for fragility.

58 GEOSCIENCES↗

Pull-out simulations of a capped carbon nanotube in carbon nanotube-reinforced nanocomposites

Systematic atomic simulations based on molecular mechanics were conducted to investigate the pull-out behavior of a capped carbon nanotube (CNT) in CNT-reinforced nanocomposites. Two common cases were studied: the pull-out of a complete CNT from a polymer matrix in a CNT/polymer nanocomposite and the pull-out of the broken outer walls of a CNT from the intact inner walls (i.e., the sword-in-sheath mode) in a CNT/alumina nanocomposite. By analyzing the obtained relationship between the energy increment (i.e., the difference in the potential energy between two consecutive pull-out steps) and the pull-out displacement, a set of simple empirical formulas based on the nanotube diameter was developed to predict the corresponding pull-out force. The predictions from these formulas are quite consistent with the experimental results. Moreover, the much higher pull-out force for a capped CNT than that of the corresponding open-ended CNT implies a significant contribution from the CNT cap to the interfacial properties of the CNT-reinforced nanocomposites. This finding provides a valuable insight for designing nanocomposites with desirable mechanical properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microstructural characterization and mechanical properties of high power ultrasonic spot welded aluminum alloy AA6111–TiAl6V4 dissimilar joints

Aluminum alloy AA6111 and TiAl6V4 dissimilar alloys were successfully welded by high power ultrasonic spot welding. No visible intermetallic reaction layer was detected in as-welded AA6111/TiAl6V4 welds, even when transmission electron microscopy was used. The effects of welding time and natural aging on peak load and fracture energy were investigated. The peak load and fracture energy of welds increased with an increase in welding time and then reached a plateau. The lap shear strength (peak load) can reach the same level as that of similar Al–Al joints. After natural aging, the fracture mode of welds transferred from ductile fracture of the softened aluminum to interfacial failure due to the strength recovery of AA6111. - Highlights: • Dissimilar Al/Ti welds were produced by high power ultrasonic spot welding. • No visible intermetallic reaction layer was detected on weld interface. • The lap shear strength can reach the same level as that of similar Al–Al joints. • The fracture mode becomes interfacial failure after natural aging.

36 MATERIALS SCIENCE↗

Traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed.

Loewenthal, S. H.↗

Elastic model of the traction behavior of two traction lubricants

In the analysis of rolling-sliding concentrated contacts, such as gears, bearings and traction drives, the traction characteristics of the lubricant are of prime importance. The elastic shear modulus and limiting shear stress properties of the lubricant dictate the traction/slip characteristics and power loss associated with an EHD contact undergoing slip and/or spin. These properties can be deducted directly from the initial slope m and maximum traction coefficient micron of an experimental traction curve. In this investigation, correlation equations are presented to predict m and micron for two modern traction fluids based on the regression analysis of 334 separate traction disk machine experiments. The effects of contact pressure, temperature, surface velocity, ellipticity ratio are examined. Problems in deducing lubricant shear moduli from disk machine tests are discussed. Previously announced in STAR as N83-20116

Loewenthal, S. H.↗

Radiation Tolerance of Silicon Carbide Joints at LWR Relevant Temperature

The development of reliable joints in reactor service conditions is a critical requirement for SiC based accident tolerant fuels and core structures for light water reactor (LWR) applications. The effects of neutron irradiation on the mechanical properties is an important consideration under normal operation. Though various SiC joints retained the strength following neutron irradiation at ∼500 and ∼800 deg. C to ∼3 dpa, the irradiation tolerance of the joints at the LWR relevant temperature is still an unknown. This study presents the strengths of the candidate SiC joints following irradiation at ∼300 deg. C. The bonding strength was investigated using torsional shear testing which was developed for miniature irradiation specimens in previous work. Torsional shear strengths of various SiC joints were evaluated following irradiation at 270-310 deg. C to 8.7 dpa. Strength degradation by the irradiation likely occurred in the Mo diffusion bond. No obvious strength degradation was found in the MAX phase and hybrid polymer/CVD joints. The irradiation caused large deviation of the strength of Ti diffusion bond, TEP slurry and tape joints. The cause of this deviation will be investigated based on microstructural analysis in future work. (authors)

36 MATERIALS SCIENCE↗

Microstructure and Properties of the Al-27Si/Cu/Al-50Si Joint Brazed by the Partial Transient Liquid Phase Bonding

Al-27Si and Al-50Si were brazed by using a thin Cu interlayer. The metallurgical bonding without obvious defects is achieved, and a wide brazing seam consisting of fine eutectic structures and coarse Si particles is formed in the Al-27Si/Cu/Al-50Si joint. The deposition of Si element in the liquid phases during solidification results in the formation of the larger Si particles and ultra-small Si particles in the brazing seam. The shear strength of the joint reaches 63 MPa.

36 MATERIALS SCIENCE↗

Hanford Sludge Simulant Selection for Soil Mechanics Property Measurement

The current System Plan for the Hanford Tank Farms uses relaxed buoyant displacement gas release event (BDGRE) controls for deep sludge (i.e., high level waste [HLW]) tanks, which allows the tank farms to use more storage space, i.e., increase the sediment depth, in some of the double-shell tanks (DSTs). The relaxed BDGRE controls are based on preliminary analysis of a gas release model from van Kessel and van Kesteren. Application of the van Kessel and van Kesteren model requires parametric information for the sediment, including the lateral earth pressure at rest and shear modulus. No lateral earth pressure at rest and shear modulus in situ measurements for Hanford sludge are currently available. The two chemical sludge simulants will be used in follow-on work to experimentally measure the van Kessel and van Kesteren model parameters, lateral earth pressure at rest, and shear modulus.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

An Investigation on Microstructure Evolution, Mechanical Properties, and Strain Aging of Mg-1.8Zn-0.7Si-0.4Ca Biomedical Alloy Processed by Equal Channel Angular Pressing

The influence of equal channel angular pressing (ECAP) on microstructure and mechanical behavior, as well as, strain aging during ECAP and post-ECAP of Mg-1.8Zn-0.7Si-0.4Ca biomedical alloy was examined. The alloy in solid solution heat-treated condition was processed by ECAP with route B{sub C} at 350 and 400 °C. The specimens ECAPed at 350 °C were aged at 125 and 150 °C for different times. The hardness and shear punch test results indicated that performing ECAP at 350 °C for 4 passes increases the hardness and shear strength of the alloy from 48 HV and 110 MPa to 71 HV and 188 MPa, respectively. It was revealed that the average grain size of the alloy decreases from 78 µm to about 3 µm after 4 passes of ECAP. Three precipitates of CaMgSi, Ca{sub 2}Mg{sub 6}Zn{sub 3}, and Mg{sub 2}Si were detected in the solid solution specimen. After 4 passes of ECAP at 350 °C, Ca{sub 2}Mg{sub 6}Zn{sub 3} was completely dissolved and the morphology of Mg{sub 2}Si changed from Chinese script to fiber-shaped particles. Dynamic strain aging occurred at high-temperature ECAP, and the specimens were overaged during post-ECAP aging. Small MgZn particles were detected in the overaged sample.

36 MATERIALS SCIENCE↗

FP-LAPW study of structural, electronic, elastic, mechanical and thermal properties of AlFe intermetallic

The structural, electronic, elastic, mechanical and thermal properties of AlFe intermetallic compound in B{sub 2}-type (CsCl) structure have been investigated using first-principles calculations. The exchange-correlation term was treated within generalized gradient approximation. Ground state properties i.e. lattice constants (a{sub 0}), bulk modulus (B) and first-order pressure derivative of bulk modulus (B’) are presented. The density of states are derived which show the metallic character of present compound. Our results for C{sub 11}, C{sub 12} and C{sub 44} agree well with previous theoretical data. Using Pugh’s criteria (B/G{sub H} < 1.75), brittle character of AlFe is satisfied. In addition shear modulus (G{sub H}), Young’s modulus (E), sound wave velocities and Debye temperature (θ{sub D}) have also been estimated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Failure of wooden sandwich beam reinforced with glass/epoxy faces

The mechanical properties and the failure of wooden beam strengthened with two faces from glass/epoxy composite and a wooden beam without strengthening was studied. Stresses and deflections on both beams, which are imposed in three point bending loading. On the idealized geometry of the specimens with detailed nonlinear orthotropic analysis was performed with a finite elements program. The failure study of the wooden beams was performed, applying the criterion of Tsai-Hill. The shear strength of the adhesive was taken into account. All the specimens were tested with three point bending loading and the experimental results were compared to those of the theoretical approach with the finite elements analysis. Comparing the results, the advantage of strengthened wooden beam against the simple wooden beam becomes obvious. Theoretical predictions were in good agreement with experimental results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effects of Interface Coating and Nitride Enhancing Additive on Properties of Hi-Nicalon SiC Fiber Reinforced Reaction-Bonded Silicon Nitride Composites

Strong and tough Hi-Nicalon SiC fiber reinforced reaction-bonded silicon nitride matrix composites (SiC/ RBSN) have been fabricated by the fiber lay-up approach. Commercially available uncoated and PBN, PBN/Si-rich PBN, and BN/SiC coated SiC Hi-Nicalon fiber tows were used as reinforcement. The composites contained approximately 24 vol % of aligned 14 micron diameter SiC fibers in a porous RBSN matrix. Both one- and two-dimensional composites were characterized. The effects of interface coating composition, and the nitridation enhancing additive, NiO, on the room temperature physical, tensile, and interfacial shear strength properties of SiC/RBSN matrix composites were evaluated. Results indicate that for all three coated fibers, the thickness of the coatings decreased from the outer periphery to the interior of the tows, and that from 10 to 30 percent of the fibers were not covered with the interface coating. In the uncoated regions, chemical reaction between the NiO additive and the SiC fiber occurs causing degradation of tensile properties of the composites. Among the three interface coating combinations investigated, the BN/SiC coated Hi-Nicalon SiC fiber reinforced RBSN matrix composite showed the least amount of uncoated regions and reasonably uniform interface coating thickness. The matrix cracking stress in SiC/RBSN composites was predicted using a fracture mechanics based crack bridging model.

Bhatt, Ramakrishana T.↗

Rheological Properties of Small-Molecular Liquids at High Shear Strain Rates

Molecular-scale understanding of rheological properties of small-molecular liquids and polymers is critical to optimizing their performance in practical applications such as lubrication and hydraulic fracking. We combine nonequilibrium molecular dynamics simulations with two unsupervised machine learning methods: principal component analysis (PCA) and t-distributed stochastic neighbor embedding (t-SNE), to extract the correlation between the rheological properties and molecular structure of squalane sheared at high strain rates (10 6 –10 10 s -1 ) for which substantial shear thinning is observed under pressures P ϵ 0.1–955 MPa at 293 K. Intramolecular atom pair orientation tensors of 435 × 6 dimensions and the intermolecular atom pair orientation tensors of 61 × 6 dimensions are reduced and visualized using PCA and t-SNE to assess the changes in the orientation order during the shear thinning of squalane. Dimension reduction of intramolecular orientation tensors at low pressures P = 0.1,100 MPa reveals a strong correlation between changes in strain rate and the orientation of the side-backbone atom pairs, end-backbone atom pairs, short backbone-backbone atom pairs, and long backbone-backbone atom pairs associated with a squalane molecule. At high pressures P ≥ 400 MPa, the orientation tensors are better classified by these different pair types rather than strain rate, signaling an overall limited evolution of intramolecular orientation with changes in strain rate. Dimension reduction also finds no clear evidence of the link between shear thinning at high pressures and changes in the intermolecular orientation. The alignment of squalane molecules is found to be saturated over the entire range of rates during which squalane exhibits substantial shear thinning at high pressures.

36 MATERIALS SCIENCE↗

Dissimilar Joining of Pure Aluminum to SiC{sub p}/Al-MMCs Using an AlMgGaLi Active Interlayer Foil

To broaden the application of advanced metal matrix composites in the electronic packaging industry, a lead-free AlMgGaLi interlayer was developed for active soldering of aluminum to aluminum metal matrix composites. The effect of joining pressure on the microstructure evolution, interfacial wettability and mechanical properties of the dissimilar joints was investigated. The experimental results indicated that as the joining pressure increased, the mean thickness of the bond seam was 46.02 μm, and solidification of a solid solution occurred (detected by SEM/XRD analysis). The composition of the Al-based solid solution (in atom%) was 86.52% Al, 9.32% Mg, 2.56% O, 1.5% Ga and 0.1% Si. The pressure improved the interfacial wettability by enhancing the atom diffusion between the interlayer and parent materials. The joint shear strength initially increased and then decreased, and a sound joint with a maximum shear strength of ~ 45 MPa was produced at 450 °C and 0.75 MPa. The fracture crack initially occurred at the interfaces of the Al/filler metal and then propagated mainly along the Al{sub 2}O{sub 3} layer on the Al side. A novel model describing the pressure-induced microstructure changes within the joint and the formation of an Al{sub 2}O{sub 3} diffusion barrier layer at the Al/filler metal interface is proposed.

36 MATERIALS SCIENCE↗

Hybrid CFRP/SWCNT Composites with Enhanced Electrical Conductivity and Mechanical Properties

The results of the investigation dealing with enhancing the mechanical and functional properties of carbon fiber-reinforced polymers are presented in the paper. The scientific issue is relevant enough to the aerospace engineering where strength-to-density ratio is one of the most important properties providing sufficient strength and stiffness along with minimal weight, while electrical and heat conductivity are required for lightning strike protection and better efficiency of thermal deicing systems, respectively. In the present research, insufficient electric conductivity of CFRP is improved by adding single-wall carbon nanotubes. Measurement of electrical resistivity of modified composites as well as CNT-filled epoxy is taken. The results of mechanical testing demonstrate unchanged tensile strength, while flexural strength increases, which is attributed to higher interfacial shear strength of hybrid CFRP/CNT composites.

77 NANOSCIENCE AND NANOTECHNOLOGY↗