Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rotational dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Investigation of Liquid Fuel Refill Dynamics in a Rotating Detonation Combustor using Megahertz Planar Laser-Induced Fluorescence

Direct imaging of liquid fuel injection is performed within an optically accessible rotating detonation combustor (RDC) using planar laser-induced fluorescence (PLIF) to spatio-temporally resolve the highly dynamic spray characteristics at rates up to 1 MHz. The RDC is operated on air and hydrogen to sustain a stable, cyclically propagating detonation wave with cycle periods of up to ∼250 μs. One of the hydrogen fuel injection sites is replaced with a liquid jet to introduce a diesel spray as a fuel surrogate to enable tracer-free fluorescence excitation using the 355 nm third-harmonic output of a burst-mode Nd:YAG laser. The time-resolved PLIF measurements reveal the evolution of the highly unsteady spray, including the dwell period after the arrival of the detonation wave, the jet recovery, breakup and entrainment into the supersonic crossflow of air, propagation into the detonation chamber, and interaction with the detonation wave. Following passage of the detonation wave, the spray characteristics reveal significant changes in the momentum flux ratio between the liquid and air streams, altering the jet trajectory and temporarily halting fuel delivery to the detonation channel. This temporary cessation of fuel spray injection into the combustor is quantified, along with the fill rate as a function of time. As the injection system recovers, the fuel spray eventually returns to a quasi-steady position prior to the arrival of the detonation wave, allowing qualitative comparisons with theoretical jet trajectories for a range of air mass-flux conditions. These data, enabled by ultra-high-speed PLIF imaging, represent some of the first detailed measurements for characterizing and quantifying the interactions of liquid jets and detonations in an operating RDC.

Propulsion↗
DOE OSTI2022

Investigating Carboxysome Morphology Dynamics with a Rotationally Invariant Variational Autoencoder

Carboxysomes are a class of bacterial microcompartments that form proteinaceous organelles within the cytoplasm of cyanobacteria and play a central role in photosynthetic metabolism by defining a cellular microenvironment permissive to CO2 fixation. Critical aspects of the assembly of the carboxysomes remain relatively unknown, especially with regard to the dynamics of this microcompartment. Progress in understanding carboxysome dynamics is impeded in part because analysis of the subtle changes in carboxysome morphology with microscopy remains a low-throughput and subjective process. Here we use deep learning techniques, specifically a Rotationally Invariant Variational Autoencoder (rVAE), to analyze fluorescence microscopy images of cyanobacteria bearing a carboxysome reporter and quantitatively evaluate how carboxysome shell remodelling impacts subtle trends in the morphology of the microcompartment over time. Toward this goal, we use a recently developed tool to control endogenous protein levels, including carboxysomal components, in the model cyanobacterium Synechococcous elongatus PCC 7942. By utilization of this system, proteins that compose the carboxysome can be tuned in real time as a method to examine carboxysome dynamics. We find that rVAEs are able to assist in the quantitative evaluation of changes in carboxysome numbers, shape, and size over time. Further, we propose that rVAEs may be a useful tool to accelerate the analysis of carboxysome assembly and dynamics in response to genetic or environmental perturbation and may be more generally useful to probe regulatory processes involving a broader array of bacterial microcompartments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Dynamic response of a freely rotating butterfly valve in the advanced test reactor – dynamic fluid-body interaction modeling

To regulate primary coolant flow in the Advanced Test Reactor (ATR), a butterfly valve was installed between the primary coolant pumps and the reactor core. If the mechanical connection between the valve's disk and its shaft ever fails, the disk will rotate freely. Rapid disk rotation may induce pressure surges that could damage upstream pipes. In the present work, the rotational trajectory and pressure evolution during a disk free-rotation scenario were analyzed via the dynamic fluid-body interaction (DFBI) approach in STAR-CCM+, with the movement of a solid being driven by the forces and moment/torque imposed by its surrounding fluid. Assuming a large initial opening angle, the disk accelerates slowly, but swiftly passes the closed position. As a result of the sudden valve closure, a pressure surge occurs in the upstream pipes, exceeding their maximum allowable pressure. Furthermore, the disk does not stabilize at the closed position but continually oscillates due to the unsteady nature of the coolant flow. Because of the significant and continuous water hammer effect, a fix to the butterfly valve is being implemented to prevent rapid valve closure due to failure at the valve's disk/shaft mechanical connection.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1983

The influence of gyroscopic forces on the dynamic behavior and flutter of rotating blades

The structural dynamics of a cantilever turbomachine blade mounted on a spinning and precessing rotor are investigated. Both stability and forced vibration are considered with a blade model that increases in complexity (and verisimilitude) from a spring-restrained point mass, to a uniform cantilever, to a twisted uniform cantilever turbomachine blade mounted on a spinning and precessing rotor are investigated. Both stability and forced vibration are considered with a blade model that increases in complexity (and verisimilitude) from a spring-restrained point mass, to a uniform cantilever, to a twisted uniform cantilever, to a tapered twisted cantilever of arbitrary cross-section. In every instance the formulation is from first principles using a finite element based on beam theory. Both ramp-type and periodic-type precessional angular displacements are considered. In concluding, forced vibrating and flutter are studied using the final and most sophisticated structural model. The analysis of stability is presented and a number of numerical examples are worked out.

Sisto, F.↗
DOE OSTI2026

Measuring dynamics of differentially rotating, unmagnetized, free-boundary plasma produced by soft x-ray irradiation

We present results from a new experiment, fielded on the MAGPIE pulsed power generator, producing a rotating, boundary-free plasma with no pre-imposed magnetic field. Angular momentum is introduced to the rotating system by the oblique collision of multiple plasma flows, which are driven by x-ray ablation of solid targets using the soft x-rays emitted from the implosion of wire array z-pinches. This produces a hydrodynamically stable plasma which undergoes ~2-3 rotations over the duration of the experiment, significantly more than previous pulsed-power platforms. Estimating the angular frequency from the electron density profile in the inner part of the rotating plasma shows that it has a quasi-Keplerian rotation profile. The system also allows for the addition of a controllable magnetic field. This, combined with the sufficiently large Reynolds (~10 5 ) and magnetic Reynolds (~10) numbers, will enable investigation of the effect of magnetic field on the structure and stability of the rotating plasma.

Physics - Plasma physics↗
NASA NTRS1976

Some dynamic problems of rotating windmill systems

The basic whirl stability of a rotating windmill on a flexible tower is reviewed. Effects of unbalance, gravity force, gyroscopic moments, and aerodynamics are discussed. Some experimental results on a small model windmill are given.

Dugundji, J.↗
NASA NTRS1978

Instrumentation for measuring the dynamic pressure on rotating compressor blades

To establish the capability for measurement of oscillatory pressure on rotating blades, miniature fast response semiconductor strain gage pressure transducers (2mm x 0.33mm) were mounted in several configurations on thin titanium and steel compressor blades and subjected to pressure cycles from 1 to 310 kPa during static tests and spin tests. Static test conditions included 20 C to 150 C, 0 to 3000 tensile microstrain, -1000 to +1000 bending microstrain and + or - 650G vibration. The spin test conditions included 20 C to 82 C at 0 to 90,000G. Durability was excellent. Pressure transducer sensitivity changed by only a few percent over this range of environmental conditions. Noise signal due to oscillatory acceleration normal to the diaphragm was acceptable (0.33Pa/G). Noise signal due to oscillatory strain was acceptable (0.5 Pa/microstrain) when the transducer was mounted on a 0.05mm rubber pad, with a total buildup of 0.38mm on the measure surface. Back mounting or partial recessing to eliminate buildup, increased the strain effect to 1.2 Pa/microstrain. Flush mounting within the blade to eliminate buildup reduced the strain effect, but required development of a special transducer shape. This transducer was not available in time for spin tests. Unpredictable zero drift + or - 14 kPa ruled out the use of these mounting arrangements for accurate steady-state (D.C.) measurements on rotating blades. The two best configurations fully developed and spin tested were then successfully applied in the NAS3-20606 rotating fan flutter program for quantitative measurement of oscillatory pressure amplitudes.

Grant, H. P.↗
NASA NTRS1981

The influence of gyroscopic forces on the dynamic behavior of rotating blades

The question of divergent oscillatory stability of an axial turbomachine blade when the bladed rotor system is subjected to a forced precessional motion is studied by using two simplified models of the blade. The simplest (lumped) model is a point mass restrained by three orthogonal linear springs attached to the rotor. An improved distributed parameter model represents the blade by a uniform cantilever beam with bending in one plane. In both instances instability is shown to be strongly dependent upon the ratio of blade root radius to blade length and the magnitude of the rotor spin relative to the nonrotating blade natural frequency for realistic values of precession rate. Results are presented on augmented Campbell diagrams. Implications for design and operation are drawn as are the characteristics of needed future studies.

Sisto, F.↗
NASA NTRS1983

On the large-scale dynamics of rapidly rotating convection zones

The fact that the values of the eight basic waves present in turbulent flows in the presence of rotation prohibit a tilt of eddy towards the axis of rotation is incorporated into a formalism for rapidly rotating convection zones. Equations for turbulent velocities are defined in a rotating coordinate system, assuming that gravity and grad delta T act in a radial direction. An expression is derived for the lifetime of a basic wave and then for the average velocity vector. A real convective eddy is formulated and the wave vectors are calculated. The velocity amplitude and the stress tensor amplitude are integrated over the eddy domain. Applied to the solar convective zone, it is found that the convective cells are aligned along the axis of rotation at the poles and at the equator, a model that conflicts with nonrotating mixng length theory predictions.

Durney, B. R.↗
NASA NTRS1985

Experimental Measurements and Analysis of Heat Transfer and Gas Dynamics in a Rotating Turbine Stage

The life-cycle fatigue of a particular component of a high-pressure turbine stage is influenced by the local heat flux and the resulting metal temperature excursions experienced by this component during normal operation. Flow through a turbine stage is seldom uniform and is often influenced by non-uniform incoming gas streams that can result in locally high heat fluxes. In the case of the rotor blades passing through the nozzle guide vane wakes and passages, these local heat rates translate into local temperature fluctuations that will likely affect the fatigue life of the blade. In order to better understand the influence of the heat load on the component life, one would like to have both the local steady-state heat flux and the high-frequency component of the heat flux.

Dunn, M. G.↗
NASA NTRS1987

Linear and nonlinear dynamic instability of rotating polytropes

A three-dimensional hydrodynamic computer program is used to study the growth of nonaxisymmetric structures in rapidly rotating, self-gravitating polytropes. Models with polytropic index n = 0.8, 1.0, 1.3, 1.5, and 1.8 are studied. The initially axisymmetric equilibria are constructed by the Ostriker-Mark self-consistent-field method. The nonaxisymmetric pattern that develops out of low-amplitude random noise is a two-armed spiral with a well-defined pattern speed and growth rate which closely match properties of the toroidal mode predicted from the linear, second-order tensor-virial equation. A Fourier analysis of each polytrope's azimuthal density distribution shows that, even in the linear amplitude regime, higher-order angular patterns also develop exponentially in time. The higher-order patterns ultimately move in synchronization with the broad two-armed spiral, creating a narrow two-armed spiral. As the polytropic index is decreased, a more open and centrally more barlike pattern develops.

Williams, Harold A.↗
NASA NTRS1956

On the gas dynamics of a rotating impeller

It is shown that for a compressible flow with constant entropy the pressure rise maintains the direct relation to the circulation around the blades existing for incompressible flow. In contrast, however, the torque, and with it the power consumption, is increased because of sound waves traveling to infinity already at subsonic circumferential speeds.

FLOW, COMPRESSIBLE↗
NASA NTRS1993

Flight-vehicle materials, structures, and dynamics - Assessment and future directions. Vol. 5 - Structural dynamics and aeroelasticity

Various papers on flight vehicle materials, structures, and dynamics are presented. Individual topics addressed include: general modeling methods, component modeling techniques, time-domain computational techniques, dynamics of articulated structures, structural dynamics in rotating systems, structural dynamics in rotorcraft, damping in structures, structural acoustics, structural design for control, structural modeling for control, control strategies for structures, system identification, overall assessment of needs and benefits in structural dynamics and controlled structures. Also discussed are: experimental aeroelasticity in wind tunnels, aeroservoelasticity, nonlinear aeroelasticity, aeroelasticity problems in turbomachines, rotary-wing aeroelasticity with application to VTOL vehicles, computational aeroelasticity, structural dynamic testing and instrumentation.

Noor, Ahmed K.↗
NASA NTRS1993

Parallel processing for nonlinear dynamics simulations of structures including rotating bladed-disk assemblies

The principal objective of this research is to develop, test, and implement coarse-grained, parallel-processing strategies for nonlinear dynamic simulations of practical structural problems. There are contributions to four main areas: finite element modeling and analysis of rotational dynamics, numerical algorithms for parallel nonlinear solutions, automatic partitioning techniques to effect load-balancing among processors, and an integrated parallel analysis system.

Hsieh, Shang-Hsien↗
DOE OSTI2025

Dynamic response of a freely rotating butterfly valve in the advanced test reactor − dynamic coefficients modeling

Here, in evaluating the water hammer issue pertaining to the primary-coolant-regulating butterfly valve in the Advanced Test Reactor, the dynamic fluid body interaction (DFBI) approach was implemented in the analysis covered in Part I. Although DFBI modeling accurately and simultaneously solved the dynamic motion of the valve’s disk along with the flow field of the surrounding fluid, it shed little light on the reason behind such motion. For Part II, the reacting torque of the fluid on the disk was decomposed into representations of the dynamic coefficients in terms of stiffness, damping, and added mass. These were evaluated via simulations with steady-state static (stiffness), constant angular speed (damping), and variable angular speed (added mass) disks. Substituting the dynamic coefficients into Newton’s second law enabled the response trajectories to be obtained. Stable (by average) and unstable equilibrium positions and thrust tendencies of the valve were determined based on the stiffness coefficient (or static torque), the response amplitude was dampened or enlarged by the damping coefficient (minorly affected by added mass), and the response frequency was altered by the damping and added mass coefficients. Although the dynamic coefficient approach renders slightly different trajectories, due to the averaging effect of the torque in comparison to the DFBI method, the overall trend of the response aligns with the DFBI simulation, thus confirming the conclusion in Part I that a fix to the current butterfly valve is necessary.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2004

The Nature of Low T/|W| Dynamical Instabilities in Differentially Rotating Stars

Recent numerical simulations indicate the presence of dynamical instabilities of the f-mode in differentially rotating stars even at very low values of T/|W|, the ratio of kinetic to potential energy. In this Letter we argue that these are shear instabilities which occur when the degree of differential rotation exceeds a critical value and the f-mode develops a corotation point associated with the presence of a continuous spectrum. Our explanation, which is supported by detailed studies of a simple shell model, offers a straightforward way of understanding all of the key features of these instabilities.

Watts, A. L.↗