Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Reduced Defects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Enhancing electron mobility in La-doped BaSnO{sub 3} thin films by thermal strain to annihilate extended defects

We report the enhancement of room-temperature electron mobility in La-doped BaSnO{sub 3} (LBSO) thin films with thermal strain induced by high temperature nitrogen (N{sub 2}) annealing. Simple annealing under an N{sub 2} environment consistently doubled the electron mobility of the LBSO films on the SrTiO{sub 3} (STO) substrates to as high as 78 cm{sup 2} V{sup −1} s{sup −1} at a carrier concentration of 4.0 × 10{sup 20 }cm{sup −3}. This enhancement is mainly attributed to annihilation of extended defects as a consequence of compressive strain induced by the difference in the thermal expansion coefficients of LBSO and STO. Our study suggests that thermal strain can be exploited to reduce extended defects and to facilitate electron transport in transparent oxide semiconductors.

36 MATERIALS SCIENCE↗

The effect of a defective BSF layer on solar cell open circuit voltage

A straightforward analysis of special limiting cases has permitted the determination of the range of possible open circuit voltage losses due to a defective BSF (back surface field) layer. An important result of the analysis is the finding that it is possible to have a fully effective BSF region, regardless of the spatial distribution of the defective areas, as long as the total defective area is reduced below certain limits. Distributed defects were found to be much more harmful than lumped defects.

Weizer, V. G.↗

Determining the Ensemble N -Representability of Reduced Density Matrices

The N-representability problem for reduced density matrices remains a fundamental challenge in electronic structure theory. Following our previous work that employs a unitary-evolution algorithm based on an adaptive derivative-assembled pseudo-Trotter variational quantum algorithm to probe pure-state N-representability of reduced density matrices [J. Chem. Theory Comput. 2024, 20, 9968], in this work we propose a practical framework for determining the ensemble N-representability of a p-body matrix. This is accomplished using a purification strategy that embeds an ensemble state into a pure state defined on an extended Hilbert space, such that the reduced density matrices of the purified state reproduce those of the original ensemble. By iteratively applying variational unitaries to an initial purified state, the proposed algorithm minimizes the Hilbert-Schmidt distance between its p-body reduced density matrix and a specified target p-body matrix, which serves as a measure of the N-representability of the target. This methodology facilitates both error correction of defective ensemble reduced density matrices and quantum-state reconstruction on a quantum computer, offering a route for density-matrix refinement. We validate the algorithm with numerical simulations on systems of two, three, and four electrons in both simple models as well as molecular systems at finite temperature, demonstrating its robustness.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Photoluminescence and positron annihilation spectroscopy of MeV Si{sup +} ion-irradiated Si{sub y}O{sub 1-y}:Er (y{approx_equal}1/3) thin films

Amorphous erbium-doped silicon oxide (Si{sub y}O{sub 1-y}:Er, y{>=}1/3) thin films are currently under investigation as a luminescent material system for complementary metal-oxide semiconductor compatible light emitters. We have grown films with y{approx_equal}1/3 and investigated their properties using both positron annihilation and photoluminescence (PL) spectroscopies. Films were characterized ''as deposited,'' following irradiation with 1 MeV Si{sup +} ions and after isochronal annealing. The PL yield from both Er{sup 3+} ions and sensitizing defects is reduced by irradiation, depending strongly on the irradiation fluence and reaching saturation at {approx}4x10{sup 13} Si{sup +}/cm{sup 2}. Higher implantation fluences result in an open-volume defect structure in the film that persists after annealing. This annealing behavior is similar to that of an unrecoverable quenching effect on Er{sup 3+}-related PL near 1540 nm, and we suggest that these open-volume defects may cause a decoupling of the Er{sup 3+} ions from sensitizing oxide point defects that form as a result of the film deposition process.

36 MATERIALS SCIENCE↗

Direct correlation and strong reduction of native point defects and microwave dielectric loss in air-annealed (Ba,Sr)TiO{sub 3}

We report on the native defect and microwave properties of 1 μm thick Ba{sub 0.50}Sr{sub 0.50}TiO{sub 3} (BST) films grown on MgO (100) substrates by molecular beam epitaxy (MBE). Depth-resolved cathodoluminescence spectroscopy (DRCLS) showed high densities of native point defects in as-deposited BST films, causing strong subgap emission between 2.0 eV and 3.0 eV due to mixed cation V{sub C} and oxygen Vo vacancies. Post growth air anneals reduce these defects with 2.2, 2.65, and 3.0 eV V{sub O} and 2.4 eV V{sub C} intensities decreasing with increasing anneal temperature and by nearly two orders of magnitude after 950 °C annealing. These low-defect annealed BST films exhibited high quality microwave properties, including room temperature interdigitated capacitor tunability of 13% under an electric bias of 40 V and tan δ of 0.002 at 10 GHz and 40 V bias. The results provide a feasible route to grow high quality BST films by MBE through post-air annealing guided by DRCLS.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Atomic structure of light-induced efficiency-degrading defects in boron-doped Czochralski silicon solar cells

Boron-doped Czochralski (Cz) Si is the most commonly used semiconductor in the fabrication of solar cells. The minority carrier lifetime of boron-doped Cz Si decreases upon exposure to light due to B–O-related defects, which reduce the performance of ~10 9 solar modules worldwide. Using electron paramagnetic resonance (EPR), we have identified the spin-active paramagnetic signatures of this phenomenon and gained insights into its microscopic mechanism. We found a distinct defect signature, which diminished when the degraded sample was annealed. The second signature, a broad magnetic field spectrum, due to the unionized B acceptors, was present in the annealed state but vanished upon light exposure. These observations show that, on degradation, nearly all the ~10 16 cm –3 B atoms in Cz Si complexed with interstitial O atoms, whereas only ~10 12 cm –3 of these complexes created defects that were recombination-active. The formation rate of these recombination-active defects correlated with the decay of the minority carrier lifetime. Furthermore, the line shape parameters linked these defects to both B and O impurities in Cz Si.

14 SOLAR ENERGY↗

Revealing Robust Room Temperature Ferromagnetism in Gd‐Doped Few‐Layered MoS 2 Thin Films

2D MoS 2 holds great promise for spintronics, yet is limited by intrinsic diamagnetism. This study demonstrates inducing ferromagnetic behavior in MoS 2 films doped with 0.47% Gd, achieving an ultrahigh saturation magnetization of 454 emu/cm 3 in a few‐layered film over 11‐times higher than bulk films (40 nm). Raman spectroscopy, X‐ray photoelectron spectroscopy, X‐ray magnetic circular dichroism, and density functional theory (DFT) calculations reveal an interplay between Gd dopants and Mo, S vacancies (V 1Mo+2S ), leading to the formation of bound magnetic polarons (BMPs) that drive ferromagnetic ordering. H 2 S annealing and DFT calculations reveal that defect healing reduces the saturation magnetization by 83%. High sulfur migration barrier in few‐layered films helps preserve BMPs, thereby sustaining ferromagnetism, whereas lower migration barriers in bulk films lead to suppression. These findings highlight the synergy between Gd doping and defect engineering in achieving ultrahigh room‐temperature ferromagnetism, offering a scalable strategy for developing high‐performance 2D magnetic materials for spintronic applications.

36 MATERIALS SCIENCE↗

CHARACTERIZING AND CONTROLLING RECOVERY AND RECRYSTALLIZATION IN NIOBIUM FOR IMPROVED SRF CAVITY PERFORMANCE

Crystal defects, such as dislocations and low-angle boundaries, provide sources of magnetic flux trapping in the Nb materials used for superconducting radio frequency (SRF) resonating cavities. Improving the performance of SRF cavities, as measured through the quality factor, requires reducing these defects. SRF cavity production involves deformation processing, such as rolling and forming, and strategic annealing heat treatments. The resulting microstructures can be recovered, recrystallized, or both. Because recovery leaves many defects that can trap flux, recrystallization should improve cavity performance. Thus, processing schedules that produce complete recrystallization without excessive grain growth need to be designed. Solutions to this problem require understanding physical metallurgy and differentiating between recovered and recrystallized regions of microstructure. Backscattered electron microscopy techniques are applied to this end. We demonstrate that the conditions required to produce fully recrystallized microstructures depend on Nb impurity content, suggesting that processing schedules may need to be adjusted by material heat or lot. We also demonstrate that processing can be used to control growth of recrystallized grains to maintain mechanical strength in fully recrystallized materials. Forming cavities from cold-rolled Nb sheet material may provide strategic new routes to obtain microstructures that improve SRF cavity performance.

Taleff, E. [The University of Texas at Austin]↗

Interfacial Defect of Lithium Metal in Solid‐State Batteries

Abstract All‐solid‐state battery with Li metal anode is a promising rechargeable battery technology with high energy density and improved safety. Currently, the application of Li metal anode is plagued by the failure at the interfaces between lithium metal and solid electrolyte (SE). However, little is known about the defects at Li–SE interfaces and their effects on Li cycling, impeding further improvement of Li metal anodes. Herein, by performing large‐scale atomistic modeling of Li metal interfaces with common SEs, we discover that lithium metal forms an interfacial defect layer of nanometer‐thin disordered lithium at the Li–SE interfaces. This interfacial defect Li layer is highly detrimental, leading to interfacial failure such as pore formation and contact loss during Li stripping. By systematically studying and comparing incoherent, coherent, and semi‐coherent Li–SE interfaces, we find that the interface with good lattice coherence has reduced Li defects at the interface and has suppressed interfacial failure during Li cycling. Our finding discovered the critical roles of atomistic lithium defects at interfaces for the interfacial failure of Li metal anode, and motivates future atomistic‐level interfacial engineering for Li metal anode in solid‐state batteries.

Yang, Menghao↗

Interfacial Defect of Lithium Metal in Solid-State Batteries

All-solid-state battery with Li metal anode is a promising rechargeable battery technology with high energy density and improved safety. Currently, the application of Li metal anode is plagued by the failure at the interfaces between lithium metal and solid electrolyte (SE). However, little is known about the defects at Li–SE interfaces and their effects on Li cycling, impeding further improvement of Li metal anodes. Herein, by performing large-scale atomistic modeling of Li metal interfaces with common SEs, we discover that lithium metal forms an interfacial defect layer of nanometer-thin disordered lithium at the Li–SE interfaces. Further, this interfacial defect Li layer is highly detrimental, leading to interfacial failure such as pore formation and contact loss during Li stripping. By systematically studying and comparing incoherent, coherent, and semi-coherent Li–SE interfaces, we find that the interface with good lattice coherence has reduced Li defects at the interface and has suppressed interfacial failure during Li cycling. Our finding discovered the critical roles of atomistic lithium defects at interfaces for the interfacial failure of Li metal anode, and motivates future atomistic-level interfacial engineering for Li metal anode in solid-state batteries.

25 ENERGY STORAGE↗

Collaborative atomic-scale design, analysis, and nanofabrication for record breaking, single-crystal Zn(x)Cd(1-x)Te solar cell arrays

Cadmium telluride (CdTe) based photovoltaics provide a viable solar energy solution because of their short payback time, low manufacturing cost, and high theoretical efficiency ~29%. However, the highest record laboratory efficiency is only 22.1% and long-term performance degradation is ~1 % per year which hinders greater economic viability. Higher open circuit voltage (Voc) and fill factor (FF) are needed to increase the efficiency of the solar cell. Cells with record energy conversion efficiencies report short current (Jsc) values close to their theoretical maximum. However, Voc and FF in these devices remain well below their anticipated optimum. These electrical parameters depend on the quality of the various layers in the solar cell. In particular they depend on the crystalline quality including the defect and impurity concentrations. Therefore understanding how defects and impurities form and evolve in the material layers is important to design devices with higher efficiency and stability. The aim of this project is to create a novel path around the fundamental barriers to achieve high open-circuit voltages (VOC ≥ 1.0 V) in CdTe/CdS solar cells. The idea of the project was to combine nanopatterned crystal growth and alloy compositional grading (with concomitant lattice parameter and energy band gap grading) to reduce the defect density and dramatically improve spatial uniformity of ZnxCd(1-x)Te/CdS cells. The lattice mismatch between ZnTe and CdS is 3.9% compared to a much larger 9.2% between CdTe and CdS. Importantly, when crystal growth is contained to the nanoscale, the strain in each layer is reduced by a factor of two due to strain partitioning and 3D strain relief mechanisms that come into play. This reduces the strain in the ZnTe from 3.9% to 1.95% which is within the range of metamorphic crystal growth. In preliminary studies, molecular dynamics simulation of ZnTe/CdS islands predicted dislocation-free material when the patterning was reduced to ~80 nm in diameter. The energy band gap of ZnxCd(1-x)Te is also graded in conjunction with alloy composition. ZnTe has an energy band gap of 2.3 eV. Finally, an added benefit of patterned growth is that it enables direct one-to-one study of the relationships between fabrication, microstructure and performance of individual crystal grains within the array. Experimental characterization techniques such as atomic probe tomography (APT) and transmission electron microscopy (TEM) have elucidated much about the microstructure of the layers. However, the techniques are destructive, costly and have limitations on the information they convey. For example, TEM gives information with atomic scale resolution but on 2-dimensional substrates. On the other hand, APT gives 3-dimensional information but is not able to resolve atomic scale structure. Alternatively, Molecular Dynamics (MD) simulations offer a solution to rapidly generate time-resolved, 3-dimensional, atomic scale structures of crystal growth. Direct MD simulations of microstructures of Cu-doped II-VI compound multilayers can impact the research on CdTe/CdS solar cells. Such MD simulations require an interatomic potential database that includes at least four elements Cu, Cd, Te, and S. The Stillinger-Weber (SW) potential is the most widely used interatomic potential for semiconductors. However, while SW potentials have been developed for Ga-In-As-Se-Te, Al-Ga-In-P-As-Sb, Cd-Te-Zn-As-Si, In-Ga-N systems, no potentials existed to simulate Cd-Zn-Hg-Se-S-Te-Cu. The goal of this effort was to fill the knowledge gap by developing a Zn-Cd-Hg-S-Se-Te-Cu SW potential database to enable MD simulations of microstructures of Cu-doped CdTe/CdS solar cells. The new potential was then applied, via MD crystal growth simulations, to study the growth mechanisms and atomic structures of the ZnTe/Cu/CdTe/CdS multilayers under various conditions. The objective of the project was to inform the solar cell community on crystal growth and defect formation at the interface between CdTe-based epilayers grown on CdS substrates. MD simulations offered a unique opportunity to analyze the 3-dimensional crystal growth evolution of Cu doped ZnxCd(1-x)TeyS(1-y) alloys with atomic scale resolution under a variety of conditions. The effect of substrate orientation and polycrystallinity on crystal growth was studied. Substrates with grain boundaries were created and the growth evolution on these substrates were analyzed. Another focus was to elucidate the effect of dopant incorporation on the nature of polycrystallinity crystal growth. Dopants available through the Stillinger-Weber potential developed in this project included Cu, Zn, S, Se, Hg and native vacancies.

14 SOLAR ENERGY↗

Low interface defect density of atomic layer deposition BeO with self-cleaning reaction for InGaAs metal oxide semiconductor field effect transistors

In this paper, we discuss atomic configuration of atomic layer deposition (ALD) beryllium oxide (BeO) using the quantum chemistry to understand the theoretical origin. BeO has shorter bond length, higher reaction enthalpy, and larger bandgap energy compared with those of ALD aluminum oxide. It is shown that the excellent material properties of ALD BeO can reduce interface defect density due to the self-cleaning reaction and this contributes to the improvement of device performance of InGaAs MOSFETs. The low interface defect density and low leakage current of InGaAs MOSFET were demonstrated using X-ray photoelectron spectroscopy and the corresponding electrical results.

36 MATERIALS SCIENCE↗

Chemical Reactivity of Reduced TiO2(110): The dominant role of surface defects in oxygen chemisorption

O2 chemisorption on reduced, rutile TiO2(110) with various concentrations of oxygen vacancies (Ov) and bridging hydroxyls (OHb) is investigated with scanning tunneling microscopy, temperature programmed desorption and electron-stimulated desorption. On the annealed surface, 2 oxygen molecules can be chemisorbed per Ov. The same amount of O2 chemisorbs on surfaces where each Ov is converted to two OHb’s by exposure to water (i.e. 1 O2 per OHb). Surfaces with few or no Ov’s or OHb’s can be created by exposing the hydroxylated surface to O2 at room temperature, and the amount of O2 that chemisorbs on these surfaces at low temperatures is only ~20% of the amount on the annealed (reduced) surface. In contrast, the amount of chemisorbed O2 increases by more than a factor of two when the OHb concentration is enhanced – without changing the concentration of sub-surface Ti interstitials. The results indicate that the reactivity of TiO2(110) is primarily controlled by the amount of electron-donating surface species such as Ov’s and/or OHb’s, and not Ti3+ interstitials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Micro-scale Numerical Investigation of Internal and Interfacial Void Defects in Adhesive on Failure Behavior of Adhesively-Bonded Materials with Rough Surfaces

This paper studied the effects of air void defects on the failure behavior of adhesively-bonded materials under global shear via micro-scale computational modeling. The numerical results indicated that interfacial void defects can largely facilitate interfacial debonding of a weaker adherend/adhesive interface under shear. However, this is not the case for a stronger adherend/adhesive interface, showing the reduction on the nominal shear strength of an adhesive joint is mainly due to internal void defects. The reduced bonding performance due to voids can be improved by leveraging an appropriate surface roughness. This preliminary investigation is a first step to better understand the micro-mechanics of interfacial failure in the adhesion of a roughened/patterned adherend via surface modification(s) and an adhesive, and also shows the importance of minimizing interfacial void defects in particular at a weaker adherend/adhesive interface via different techniques.

Qiao, Yao↗

Physisorption of molecular hydrogen on carbon nanotube with vacant defects

Physisorption of molecular hydrogen on single-walled carbon nanotubes (SWCNTs) is important for its engineering applications and hydrogen energy storage. Using molecular dynamics simulation, we study the physisorption of molecular hydrogen on a SWCNT with a vacant defect, focusing on the effect of the vacant defect size and external parameters such as temperature and pressure. We find that hydrogen can be physisorbed inside a SWCNT through a vacant defect when the defect size is above a threshold. By controlling the size of the defects, we are able to extract hydrogen molecules from a gas mixture and store them inside the SWCNT. We also find that external parameters, such as low temperature and high pressure, enhance the physisorption of hydrogen molecules inside the SWCNT. In addition, the storage efficiency can be improved by introducing more defects, i.e., reducing the number of carbon atoms on the SWCNT.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Identification and Suppression of Point Defects in Bromide Perovskite Single Crystals Enabling Gamma‐Ray Spectroscopy

Abstract Methylammonium lead tribromide (MAPbBr 3 ) stands out as the most easily grown wide‐band‐gap metal halide perovskite. It is a promising semiconductor for room‐temperature gamma‐ray ( γ ‐ray) spectroscopic detectors, but no operational devices are realized. This can be largely attributed to a lack of understanding of point defects and their influence on detector performance. Here, through a combination of crystal growth design and defect characterization, including positron annihilation and impedance spectroscopy, the presence of specific point defects are identified and correlated to detector performance. Methylammonium (MA) vacancies, MA interstitials, and Pb vacancies are identified as the dominant charge‐trapping defects in MAPbBr 3 crystals, while Br vacancies caused doping. The addition of excess MABr reduces the MA and Br defects and so enables the detection of energy‐resolved γ ‐ray spectra using a MAPbBr 3 single‐crystal device. Interestingly, the addition of formamidinium (FA) cations, which converted to methylformamidinium (MFA) cations by reaction with MA + during crystal growth further reduced MA defects. This enabled an energy resolution of 3.9% for the 662 keV 137 Cs line using a low bias of 100 V. The work provides direction toward enabling further improvements in wide‐bandgap perovskite‐based device performance by reducing detrimental defects.

Ni, Zhenyi↗

Strain Relaxation and Relative Defect Density with Thickness in MBE-Grown Ge 0.85 Sn 0.15 on Ge(001)

Germanium–tin (GeSn) alloys are emerging as promising materials for mid-infrared optoelectronics and silicon-compatible photonic devices, owing to their tunable direct bandgap. However, the growth of high-quality GeSn films with high Sn content remains challenging due to strain-induced defect formation. In this study, we investigate the role of film thickness on strain-induced relaxation, defect density, and Sn segregation. A series of five samples with varying thicknesses and ∼15% Sn-containing GeSn layers were grown, ranging from the critical thickness for strain relaxation to the onset of Sn segregation. All GeSn samples were analyzed using X-ray diffraction reciprocal space mapping (XRD-RSM) to explore the evolution of strain-induced relaxation as a function of thickness. Photoluminescence measurements reveal that increasing the GeSn thickness enhances strain relaxation while reducing defect-related emission, indicating a decrease in effective defect density prior to reaching the threshold thickness of GeSn layer. At a thickness of ∼150 nm, the GeSn layer shows the onset of Sn segregation, evident in the XRD-RSM spectrum, marking the threshold thickness for Sn segregation. This work defines an effective growth window in terms of thickness (35 to 150 nm) for fabricating relaxed, defect-suppressed GeSn layers with 15% Sn content. These findings emphasize the crucial role of thickness control in balancing strain relaxation and defect suppression, advancing the fabrication of high-quality, high Sn-content relaxed GeSn using molecular beam epitaxy.

Defects↗