SEARCH · Engineering Papers

Results for “Quasi-static”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Large deflection behavior of quasi-isotropic laminates under low-velocity impact type point loading

Eight-ply quasi-isotropic circular composite plates of Thornel 300 graphite in Narmco 5208 epoxy resin (T300/5208) were analyzed to obtain the large deformation behavior under low-velocity impact type point loads. A simple plate-membrane coupling model was developed. The impact type point loads were replaced by equivalent quasi-static point loads. The plate-membrane coupling model was used to obtain the large deformation shapes for the thin circular composite laminates. The analyses indicated that the large deformation shapes of the composite plates under point loads vary with the center point displacements, and hence are different for different load levels. Quasi-isotropic plates were analyzed by replacing anisotropic bending stiffness components with the equivalent flexural stiffness for the isotropic plates. The plate-membrane coupling model was verified by conducting a series of tests on clamped circular quasi-isotropic laminates. Deflected shapes for the thin composite plates were experimentally obtained. These shapes agreed well with the analytically predicted shapes.

Kelkar, A.↗

NASA NTRS1984

Aeromechanical stability of a full-scale hingeless rotor in hover

The aeroelastic stability in hover of a 9.8-m-diam, hingeless helicopter rotor system is evaluated. Rotor inplane damping data were obtained for rotor operation between 350 and 425 rpm for thrust coefficients between 0.0 and 0.12. At constant rotor rotational speed, a minimum inplane damping level was obtained at a thrust coefficient of approximately 0.02. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Correlation with a comprehensive aeroelastic stability program is found to be good. The influence of different aerodynamic inflow models on predicted damping levels is shown. Best correlation with experimental data is obtained using a dynamic inflow model rather than static or quasi-static inflow models. Comparison with other full-scale, hingeless rotor stability data in hover is presented. Also, direct comparisons are made with data from a full-scale bearingless main rotor test performed on the same general-purpose test apparatus. Although the bearingless rotor is more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown.

Peterson, R. L.↗

NASA NTRS1985

CNO abundances resulting from diffusion in accreting nova progenitors

The configurations of potential nova progenitors at the onset of a thermonuclear runaway (TNR) are obtained by evolving a series of white dwarf (WD) models through the quasi-static accretion phase preceding the TNR. Special attention is paid to the effect of diffusion on composition profiles. The initial parameters of the accretion phase are the WD mass, the WD luminosity, and the accretion rate. They lead to a wide range of combinations of accreted mass and heavy element content of the envelope Z(env). It is found that the WD mass is the most important parameter in determining the accreted mass. A lower limit exists for the mass of a WD capable of producing a nova-like outburst which decreases with decreasing WD mass. There is a strong correlation between the accretion rate and Z(env), higher Z(env) values resulting from lower accretion rates. Changes in WD luminosity have no dramatic effect on the outcome of the accretion phase.

Kovetz, A.↗

NASA NTRS1985

Atmospheric electric field and current configurations in the vicinity of mountains

A number of investigations have been conducted regarding the electrical distortion produced by the earth's orography. Hays and Roble (1979) utilized their global model of atmospheric electricity to study the effect of large-scale orographic features on the currents and fields of the global circuit. The present paper is concerned with an extension of the previous work, taking into account an application of model calculations to orographic features with different configurations and an examination of the electric mapping of these features to ionospheric heights. A two-dimensional quasi-static numerical model of atmospheric electricity is employed. The model contains a detailed electrical conductivity profile. The model region extends from the surface to 100 km and includes the equalization layer located above approximately 70 km. The obtained results show that the electric field and current configurations above mountains depend upon the curvature of the mountain slopes, on the width of the mountain, and on the columnar resistance above the mountain (or mountain height).

Tzur, I.↗

NASA NTRS1985

An analysis of the Space Shuttle hypersonic entry trim anomaly

This paper reviews a parameter identification methodology developed to investigate the hypersonic longitudinal trim misprediction apparent in the NASA Space Shuttle Orbiter entry flights. The method combines an analysis using a measured versus predicted technique in conjunction with a multilinear regression analysis to identify prediction deficiencies using quasi-static longitudinal data in the hypersonic flight regime (Mach 6 through 26). In general, the results of this extraction confirm results previously obtained by other Shuttle investigators with the exception of elevon effectiveness. Further analysis and/or flight data will be required to resolve the conflicting elevon results. A combination of this analytical tool and other flight data will enable flight data interpretation with the potential for identifying the sources of the Shuttle's hypersonic trim misprediction to an accuracy consistent with updating preflight prediction methodology for future spacecraft.

Young, J. C.↗

NASA NTRS1984

Quantitative assessment of damage growth in graphite epoxy laminates by acousto-ultrasonic measurements

The acoustoultrasonic NDT method proposed by Vary (1976, 1978) for composite laminate damage growth quantitative assessment can both respond to the development of damage states and furnish quantitative parameters that monitor this damage development. Attention is presently given to data obtained for the case of quasi-static loading and fatigue testing of graphite-epoxy laminates. The shape parameters of the power spectral density for the ultrasonic signals correlate well with such other indications of damage development as stiffness degradation.

Talreja, R.↗

NASA NTRS1985

Opening of the magnetic field lines in a fast rotating magnetosphere, with an application to Jupiter

A simple model of a magnetosphere rotating around a rotating Jupiter-like object with a spin-aligned dipolar moment mu is considered. A low-energy plasma is released by inner sources located beyond the corotation radius and is diffused outward through closed lines. The lines form a closed thin equatorial disk, maintaining a quasi-static balance between the centrifugal force and the magnetic tension. Solutions are obtained for the analytical equations characterizing the plasma in the closed region; the structure of the magnetic field outside the disk; and the self-consistent value of the critical radius r sub zero. The analytical solutions are compared to the observed properties of the Jovian magnetosphere, and the results are discussed in detail.

Aly, J. J.↗

NASA NTRS1984

Acousto-ultrasonic measurements to monitor damage during fatigue of composites

An acousto-ultrasonic nondestructive testing method used to monitor damage during static and fatigue loading of thin graphite epoxy laminates is described. The experimental procedure, the signal analysis by the Fast Fourier Transform (FFT) algorithm, and the results of this analysis are discussed. Quasi-static tension tests showed a sharp decrease in the quantitative parameters when transverse cracks developed in the 90 degrees plies of a (0, 90/2/)s laminate. When internal micro-delaminations unite to form macro-delaminations, a sharp decrease in the parameters is also observed. The parameters are found to correlate well with other indications of damage development such as stiffness and degradation. The root mean square value of the moment is found to be more sensitive to damage than stiffness. Various signals and spectrums of graphite epoxy systems are presented.

Govada, A.↗

NASA NTRS1985

On the observed properties and long-term structure and evolution of white dwarfs in cataclysmic variables

An attempt is made to explain the observed surface temperatures and luminosities of cataclysmic variable white dwarfs based on the cooling physics and time-averaged structure of the white dwarf in response to accretion. The evolutionary changes in core temperature and core luminosity as an accreting white dwarf evolves quasi-statically are compared with the cooling evolution of a nonaccreting, one solar mass, pure C-12 core. Then, the evolutionary behavior of the white dwarf envelope in mass and temperature, in response to long-term accretion, is used to predict temperatures and luminosities of white dwarfs during quiescent intervals between nova outbursts. It is shown that the observed luminosities and effective temperatures of the bare white dwarfs detected in some cataclysmic variables are the expected intrinsic values associated with classical nova thermonuclear outburst cycles. Two alternate interpretations of their observed surface temperatures and luminosities are assessed.

Sion, E. M.↗

NASA NTRS1985

Effects of strain rate on delamination fracture toughness of graphite/epoxy

The objective of this paper is to evaluate various experimental techniques and analysis methods for the characterization of interlaminar fracture toughness, and to determine the effects of strain rate on that property for a graphite/epoxy composite. Mode I interlaminar fracture was investigated by means of a double-cantilever beam (DCB) specimen for AS-4/3501-6 graphite/epoxy. Hinged tabs were used to insure unrestrained rotation at the free ends. Specimens were loaded at quasi-static deflection rates of up to 8.5 mm/s corresponding to crack extension rates of over 51 mm/s. Crack extension was monitored by means of strain gages mounted on the surface of the specimen, or a conductive-paint circuit attached to the edge of the DCB specimen. Continuous records were obtained of load, deflection, and crack extension for determination of the strain energy release rate. The latter was expressed as a power law of the crack extension velocity. Results indicate that the strain energy release rate increases with crack velocity by up to 28 percent for the range of rates considered.

Daniel, I. M.↗

NASA NTRS1986

Spectral flux from low-density photospheres - Numerical results

Radiative transfer through sharp, quasi-static atmospheres whose opacity is dominated by hydrogen is considered at densities low enough that scattering usually dominates absorption and radiative excitations usually dominate collisional excitations. Numerical results for the continuum spectral flux are obtained for effective temperatures T(e) = 6000-16,000 K and scale heights Delta-R = 10 to the 10th - 10 to the 14th cm. Spectra are significantly different than if LTE level populations were assumed. Comparison with observations of the Type II supernova 1980k tends to increase the value of the Hubble constant previously obtained by the Baade (1926) method.

Hershkowitz, S.↗

NASA NTRS1985

On-orbit parameter and disturbance identification for Space Station

This paper describes recent efforts directed at the problem of on-orbit parameter and disturbance identification for the Space Station. Techniques are developed for identification of rigid body parameters, flexible body parameters, and quasi-static disturbances relevant to the Power Tower configuration currently under investigation by NASA. The paper concludes with a case study investigating the identification of modal frequencies in a 15 degree of freedom planar model of the Space Station under a variety of operational settings.

Bayard, D. S.↗

NASA NTRS1986

Cascade model of coronal heating

It is suggested that the quasi-static evolution of coronal magnetic structures is characterized by a cascade of magnetic energy to smaller length scales. This cascade process takes place on a time scale t sub b determined entirely by the photospheric motions. The Ohmic heating rate E sub H in the statistically stationary state was estimated using observational data on the diffusivity of photospheric motions; E sub H turned out to be too small by a factor of 40 when compared with observed coronal energy losses. However, given the fact that the theoretical estimate is based on a rather uncertain extrapolation to the diffusive regime, current heating cannot be ruled out as a viable mechanism of coronal heating.

Vanballegooijen, A. A.↗

NASA NTRS1986

Primordial stellar evolution - The pre-main-sequence phase

The quasi-static contraction of primordial stars composed of pure hydrogen and helium gas is studied by following numerically the evolution of a star of five solar masses from the end of protostellar accretion to the onset of hydrogen burning. Although the protostellar core of this mass is radiatively stable and undergoing nonhomologous contraction, its large surface area and luminosity force the star to a partially convective, homologously contracting state within only 100 yr. Deuterium later ignites at an off-center temperature maximum but fails to produce interior convection. The star follows a conventional premain sequence track in the HR diagram, reaching the ZAMS after 1.2 million yr, with a luminosity of 880 solar luminosities and a radius of 1.2 solar radii.

Stahler, S. W.↗

NASA NTRS1986

Magnetospheric equilibrium configurations and slow adiabatic convection

This review paper demonstrates how the magnetohydrostatic equilibrium (MHE) theory can be used to describe the large-scale magnetic field configuration of the magnetosphere and its time evolution under the influence of magnetospheric convection. The equilibrium problem is reviewed, and levels of B-field modelling are examined for vacuum models, quasi-static equilibrium models, and MHD models. Results from two-dimensional MHE theory as they apply to the Grad-Shafranov equation, linear equilibria, the asymptotic theory, magnetospheric convection and the substorm mechanism, and plasma anisotropies are addressed. Results from three-dimensional MHE theory are considered as they apply to an intermediate analytical magnetospheric model, magnetotail configurations, and magnetopause boundary conditions and the influence of the IMF.

Voigt, Gerd-Hannes↗

NASA NTRS1984

The thermocapillary motion of two bubbles oriented arbitrarily relative to a thermal gradient

The interaction problem of two bubbles oriented at an arbitrary angle to a thermal gradient in the absence of gravity is studied. The problem is considered in the quasi-static limit, wherein unsteady and convective transport terms are completely neglected in the momentum and energy equations. Instead of bipolar coordinates, an approximation used in a previous analysis of the interaction effects of two bubbles moving along their line of centers in a thermal gradient is applied here to predict the interaction parameter.

Meyyappan, M.↗

NASA NTRS1986

Large Deformation Dynamic Bending of Composite Beams

Studies were conducted on the large deformation response of composite beams subjected to a dynamic axial load. The beams were loaded with a moderate eccentricity to promote bending. The study was primarily experimental but some finite element results were obtained. Both the deformation and the failure of the beams were of interest. The static response of the beams was also studied to determine potential differences between the static and dynamic failure. Twelve different laminate types were tested. The beams tested were 23 in. by 2 in. and generally 30 plies thick. The beams were loaded dynamically with a gravity-driven impactor traveling at 19.6 ft/sec and quasi-static tests were conducted on identical beams in a displacement controlled manner. For laminates of practical interest, the failure modes under static and dynamic loadings were identical. Failure in most of the laminate types occurred in a single event involving 40% to 50% of the plies. However, failure in laminates with 300 or 150 off-axis plies occurred in several events. All laminates exhibited bimodular elastic properties. The compressive flexural moduli in some laminates was measured to be 1/2 the tensile flexural modulus. No simple relationship could be found among the measured ultimate failure strains of the different laminate types. Using empirically determined flexural properties, a finite element analysis was reasonably accurate in predicting the static and dynamic deformation response.

Derian, E. J.↗

NASA NTRS1959

An Analysis of Flight-Test Measurements of the Wing Structural Deformations in Rough Air of a Large Flexible Swept-Wing Airplane

An analysis is made of wing deflection and streamwise twist measurements in rough-air flight of a large flexible swept-wing bomber. Random-process techniques are employed in analyzing the data in order to describe the magnitude and characteristics of the wing deflection and twist responses to rough air. Power spectra and frequency-response functions for the wing deflection and twist responses at several spanwise stations are presented. The frequency-response functions describe direct and absolute response characteristics to turbulence and provide a convenient basis for assessing analytic calculation techniques. The wing deformations in rough air are compared with the expected deformations for quasi-static loadings of the same magnitude, and the amplifications are determined. The results obtained indicate that generally the deflections are amplified by a small amount, while the streamwise twists are amplified by factors of the order of 2.0. The magnitudes of both the deflection velocities and the twist angles are shown to have significant effects on the local angles of attack at the various stations and provide the main source of aerodynamic loading, particularly at frequencies in the vicinity of the first wing-vibration mode.

Murrow, Harold N.↗