SEARCH · Engineering Papers

Results for “Pore volume”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Insights into Controls of Mineralogy and Pore Structure on the Density of Methane Adsorption Phase in Shales under Supercritical Conditions

With gradually increasing enhancing population and industrialization, exploitation of shale gas is enhancing in the world to satisfy the growing demand for energy worldwide. To exploit shale gas efficiently, accurate assessment of shale gas in place (GIP) is necessary for determining production strategies. Unlike free and dissolved gas, adsorbed gas contributes to the shale GIP up to 85% due to the well-developed surface area and micropores. Measured excess adsorption of methane (up to over 95% of subsurface shale gas) is often corrected to absolute adsorption to obtain the actual amount of adsorption under supercritical (or geological) conditions. During the correction, adsorption phase density (APD) is critical. However, the APD of subsurface shale gas and the effects of shale properties (e.g., mineralogy and pore structure) on APD remain poorly understood. A series of high-pressure methane adsorption isotherms (HPMAI) on Caney Shales were collected and analyzed in conjunction with other United States and Chinese shales from the literature at 35–125 °C and up to 15 MPa. Here, a three-layer Ono–Kondo (OK3) model is utilized to derive the temperature- and pressure-dependent APD coupling low-pressure nitrogen adsorption isotherms (LPNAI) and HPMAI. X-ray diffraction and organic geochemistry are combined to reveal the mineralogy. Brunauer–Emmett–Teller, Barrett–Joyner–Halenda, and Horvath–Kawazoe analyses via LPNAI are used to investigate the pore structures. Results show that APD increases with organic matter (OM) proxied by total organic carbon and decreases with clay minerals and the sum of quartz and feldspar. OM dramatically contributes to the APD as multiple-layer adsorption exists, and the APD for OM could be 1.4–8.5 times that for clay minerals. Other inorganic minerals contribute less to APD. The properties and constitution of the surface area instead of the volume fraction contribute to the APD in shales. APD does not show an obvious correlation with micropore volume, likely related to the ratio of micropore volume to the total pore volume. Here, we provide a significant and comprehensive study of petrological factors that impact the APD of subsurface shale gas, which will improve the estimation of supercritical adsorption and shale GIP under reservoir conditions. Also, the findings in this work can provide applications for subsurface carbon dioxide adsorption and storage.

58 GEOSCIENCES↗

DOE OSTI2023

Numerical Simulations of Carbon Dioxide Storage Efficiency in Heterogeneous Reservoir Models

The U.S. Department of Energy’s National Energy Technology Laboratory (DOE-NETL) has been developing methods and tools (the online Carbon Dioxide Storage prospeCtive Resource Estimation Excel aNalysis (CO2-SCREEN) tool) to estimate carbon dioxide (CO2) storage potential in subsurface reservoirs. The CO2 storage efficiency terms are input in the tool to calculate storage potential in targeted reservoirs. In this effort, two CO2 storage efficiency terms were evaluated: volumetric displacement ( E V ) and microscopic displacement ( E d ). The first term deals with efficiency of CO2 propagation into an accessible reservoir volume, while the second term evaluates effectiveness of native fluid displacement with CO2. The interpreted well logs and core sample measurements were applied to create the heterogeneous reservoir models including geostatistical realizations of porosity and intrinsic permeability fields. Supercritical CO2 was injected over the course of 30 years into brine-saturated reservoir models for clastics, limestone, and dolomite lithologies and deltaic fluvial, aeolian, shallow marine, and reef depositional environments by means of varying reservoir parameters and injection scenarios. The reservoir models providing vertically heterogeneous petrophysical properties and designated as “layered reservoir models” (with homogeneous parameters along each layer of the model) were not determined to be a transition between the homogeneous and heterogeneous models in respect to storage efficiency. Another finding shows that high-efficiency factors do not necessarily mean increased CO2 storage; they rather indicate that the available volume and pore space are more fully utilized. The CO2 storage efficiency factors were evaluated dynamically at the select time points using P 10 ‐ P 50 ‐ P 90 percentiles. The results of this study show that the P 10 ‐ P 90 distribution for volumetric efficiency is wider when compared to the microscopic efficiency. It was found that where dominant buoyancy forces drive the plume to the top of a target formation, the volumetric efficiency is low. Tighter sandstone and carbonate formations show prevalence of capillary forces and better utilization of reservoir volume.

Myshakin, Evgeniy M.↗

DOE OSTI2024

Macroscopic modeling of gas permeability in hierarchical micro/nanoporous media: A unified characterization of rarefaction using Klinkenberg theory and equivalent diameter

Estimating gas transport through a hierarchical micro/nanoporous system is challenging due to non-equilibrium gas dynamics. The primary difficulty lies in determining the rarefaction level, because identifying a representative flow dimension in a complex porous system with multiple pore scales is not straightforward. Our study performed a pore-level analysis for gas permeability in dual-scale porous media with varying porosity, throat size, and secondary pore size under different rarefaction conditions. We found that secondary porosity negatively affects permeability due to increased friction forces, with this influence growing as the secondary pore size and porosity increase until the secondary pore becomes comparable to the throat. However, rarefaction reduces the effects of secondary pores due to boundary slip. Traditional Knudsen number (Kn) calculations based on Darcy-defined height failed to accurately describe the rarefaction effects on gas permeability. Instead, we introduced an equivalent diameter to calculate the Kn, which provided an accurate normalization of apparent gas permeability independent of pore geometry. Furthermore, the extended Kozeny–Carman–Klinkenberg model developed in our previous study successfully yielded a macroscopic model for apparent gas permeability in hierarchical micro/nanoporous systems as a function of the traditional Darcy height and porosity.

04 OIL SHALES AND TAR SANDS↗

DOE OSTI2024

Correlative X-ray micro-nanotomography with scanning electron microscopy at the Advanced Light Source

Geological samples are inherently multi-scale. Understanding their bulk physical and chemical properties requires characterization down to the nano-scale. A powerful technique to study the three-dimensional microstructure is X-ray tomography, but it lacks information about the chemistry of samples. To develop a methodology for measuring the multi-scale 3D microstructure of geological samples, correlative X-ray micro- and nanotomography were performed on two rocks followed by scanning electron microscopy with energy-dispersive spectroscopy (SEM-EDS) analysis. The study was performed in five steps: (i) micro X-ray tomography was performed on rock sample cores, (ii) samples for nanotomography were prepared using laser milling, (iii) nanotomography was performed on the milled sub-samples, (iv) samples were mounted and polished for SEM analysis and (v) SEM imaging and compositional mapping was performed on micro and nanotomography samples for complimentary information. Correlative study performed on samples of serpentine and basalt revealed multiscale 3D structures involving both solid mineral phases and pore networks. Significant differences in the volume fraction of pores and mineral phases were also observed dependent on the imaging spatial resolution employed. This highlights the necessity for the application of such a multiscale approach for the characterization of complex aggregates such as rocks. Information acquired from the chemical mapping of different phases was also helpful in segmentation of phases that did not exhibit significant contrast in X-ray imaging. Adoption of the protocol used in this study can be broadly applied to 3D imaging studies being performed at the Advanced Light Source and other user facilities.

58 GEOSCIENCES↗

DOE OSTI2024

Experimental investigation of the influence of drainage condition on change in saturation of sheared sand

Here, this paper investigates the validity of the interpretation of results from testing saturated axisymmetric triaxial compression (ATC) sand specimens utilising three-dimensional (3D) synchrotron micro-computed tomography (SMT) to probe localised events that are completely missed or misinterpreted when analysing ATC measurements based on global standard measurements. Drained and undrained experiments were conducted at low and high back-pressures (BPs) coupled with multiple in situ 3D SMT to acquire high-resolution scans of the specimens at different axial strains. Specimens tested under low BP exhibited a large pore air volume change, which was not detected by the pump system that represents standard volume measurement. The increase in air volume caused a significant reduction in the degree of saturation leading to a possible transition from saturated to partially saturated constitutive behaviour. Undrained experiments exhibited a significant volume change contrary to the assumption of negligible volumetric strain for saturated undrained experiments. Air bubbles within the shear band for drained and undrained low-BP specimens showed opposite capillary pressure responses, increased for drained and decreased for undrained cases, due to the variation in the mechanism by which each of the two experiments predominantly counters the volume expansion within the shear band.

capillary pressure↗

NASA NTRSDate not supplied

Updates on the Predictive Materials Modeling Software Tools

Updates on NASA‘s efforts to build a Predictive Material Modeling (PMM) framework from the micro-scale to the macro-scale are presented in this abstract. The PMM effort is part of the Entry Systems Modeling (ESM) project under NASA’s Game Changing Development (GCD) program. To reduce the need for extensive testing and accelerate the design cycle process, ESM is developing simulation and modeling tools that enable the characterization of the properties of thermal protection materials and their response to extremely hot plasma. The Porous Microstructure Analysis (PuMA) software has been developed to compute effective material properties and perform material response simulations on digitized microstructures of porous media. PuMA is able to import three-dimensional digital images obtained from X-ray microtomography or to generate artificial microstructures that mimic real materials. PuMA also provides a module for interactive 3D visualizations. Version 3, which was recently released as open-source, includes modules to compute simple morphological properties such as porosity, volume fractions, pore diameter, and specific surface area. Additional capabilities include the determination of effective thermal and electrical conductivity (both radiative and solid conduction - including the ability to simulate local anisotropy for the latter); effective diffusivity and tortuosity from the continuum to the rarefied regime; techniques to determine the local material orientation, as well as mechanical properties (elasticity coefficients), and permeability. Computed properties are then used to inform a macro-scale material response model, such as those implemented in the Porous material Analysis Toolbox based on OpenFOAM (PATO) software developed within ESM. The computational model in PATO is a generic heat and mass transfer model for porous reactive materials containing several solid phases and a single gas phase. The detailed chemical interactions occurring between the solid phases and the gas phase are modeled at the pore scale, assuming Local Thermal Equilibrium. Recent efforts include the development of a mechanical erosion model as well as a unified model allowing an intrinsic coupling between fluid and material. Comparison to flight data (Mars Science Laboratory [MSL] Entry Descent and Landing Instrument [MEDLI] and Mars 2020 MEDLI2) is critical in order to validate these computational tools. Examples of ablative material response using the code will be presented, including 3D simulations of the full-scale heatshield of the MSL capsule. The simulations demonstrated the ability of the modern material response code, PATO, to handle the material response of geometrically complex and large domains through the use of massively parallel computations.

material modeling↗

NASA NTRSDate not supplied

Mineralogical, Elemental and Tomographic Reconnaissance Investigation for CLPS (“METRIC”)

METRIC comprises a suite of two instruments in a Lunar lander that perform X-ray diffraction (XRD) for mineral structure, X-ray fluorescence (XRF) for elemental composition, and X-ray Micro Computed Tomography (XCT) for 3D internal micromorphology. The instruments are accompanied by optical-near IR cameras to provide local geologic context. The Honeybee Robotics PlanetVac pneumatic sampling and transfer system [1],positioned on a lander footpad, will deliver sieved regolith to the X-ray instruments for analysis. The instrument suite is intended for delivery to the lunar surface on a Commercial Lunar Payload Services (CLPS) lander. The METRICXRD/F instrument draws on heritage from the Mars Science Laboratory CheMin instrument [2] and improves upon the design in multiple ways [3]. Like CheMin, Rietveld refinement and full-pattern fitting of METRIC XRD data can identify minerals at a detection limit of ~1 wt.%, quantify their abundances when present at >3 wt.%, and determine mineral composition (e.g., Fo#in olivine) from lattice parameters for minerals present at >5 wt.%[4,5]. An optimized XRF geometry provides for improved detection and quantification of major, minor and trace elements. The METRIC XCT instrument is a miniaturized X-ray Computed Tomography scanner[6]. Lunar regolith is delivered to a 3 mm diameter, 10 mm long graphite tube inside the instrument. The tube is rotated through 360°in 0.9deg.incrementsand a divergent point source X-ray beam is directed through the material. A Charge Coupled Device (CCD)records attenuation images whose brightness and contrast area function of average atomic number and density. Quantitative data, including particle and void sizes, 3D particle shape parameters, modal volumes and pore geometry can be derived from the resulting 3D reconstructions(voxel resolution: 30 μm). Crystal morphologies derived from METRIC XCT data complement the bulk mineralogy determined by the METRIC XRD/F and provide a measure of grain size distribution for the different phases. Taken together, the METRIC instrument suite determines crystal structure, elemental composition and morphology, three principal characteristics of geological materials that are highly useful in determining the origin and subsequent processing of lunar regolith.

Moon↗

NASA NTRS2020

A 3D Model to Predict Explicit Morphologies and Volume Fraction of Lack-of-Fusion Pores Generated in Selective Laser Melting Processes

The performance of an additively manufactured (AM) component is dependent on the distribution of process-induced defects in addition to the complex microstructure of the material, surface roughness of the component and the process-induced residual stresses. For instance, it has been well demonstrated that lack-of-fusion (LoF) pores produced in the selective laser melting (SLM) AM process can significantly limit the fatigue performance of the material. Although two-dimensional (2D) models exist to predict the 2D profiles of LoF pores, the 2D pore profiles cannot be directly inserted into a three-dimensional (3D) microstructure domain that is output from several prevailing process simulation packages. A few commercial packages that simulate the SLM process can predict LoF pores in a 3D domain, but the morphologies of LoF pores are voxelated and hence do not capture sharp corners of the pores, thereby obviating their use in fatigue crack initiation studies. In order to address the aforementioned gaps, a high-fidelity model that predicts not only the volume fraction, but also the explicit 3D morphologies and spatial distributions of LoF pores has been developed using a computer aided design-based environment. The model has been partially validated for Ti-6Al-4V alloy by comparing the predictions of the volume fraction of LoF pores predicted by the model with experimental data obtained from the literature. Absolute error in predicted volume fraction of LoF pores varied between 5.16% and 1.87% for energy density values between 13 J/mm3 and 45 J/mm3 where a significant amount (over 3% volume fraction) of LoF porosity was measured. The absolute error was within 1.87% for energy density values greater than 45 J/mm3.

Saikumar R. Yeratapally↗

DOE OSTI2021

Key properties of mixed cerium and zirconium microspheres prepared by the internal gelation process with previously boiled HMTA and urea

The internal gelation process using previously boiled hexamethylenetetramine-urea was used in exploratory study to produce CeO 2 –ZrO 2 microspheres, which can serve as a simulant for ceramic transuranic fuel particles and as a viable three-way catalyst. The calcined CeO 2 and ZrO 2 microspheres with Barrett–Joyner–Halenda (BJH) pore size and volumes of 8–10 nm and 0.19–0.20 mL/g, respectively, had many more surface cracks than their relatively smooth CeO 2 –ZrO 2 counterparts even though the BJH pore sizes and volumes of mixed oxide spheres were lower at 3 nm and 0.11–0.12 mL/g, respectively. The Brunauer–Emmett–Teller (BET) surface areas for the CeO 2 and ZrO 2 microspheres were 74 and 93 m2/g, respectively, and the BET surface areas for the mixed oxides were much greater at 155–158 m 2 /g, which should improve catalytic performance. Overall, the catalytic activity of each microsphere composition was confirmed through the oxidation of carbon monoxide.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Engineered Cementitious Composites (ECC) with limestone calcined clay cement (LC 3 )

Recent research have recognized that coupled use of calcined clay, limestone and cement clinker in concrete is viable to reduce environmental footprints at manufacture and to enhance material durability. In this study, a novel application of the limestone calcined clay cement (LC 3 ) is demonstrated by substituting the Ordinary Portland Cement (OPC) in Engineered Cementitious Composites (ECC). The composite mechanical properties including σ-δ and σ-ε relationships and residual crack widths were evaluated to 28 days under uniaxial tension. Matrix chemistry was characterized using thermogravimetric analysis and X-ray diffraction, while the pore structure of matrices and composites was analyzed using mercury intrusion porosimetry. The LC 3 -based ECC showed more rapid early strength development but lower 28-day strength (~32 MPa) due to a 20% higher water-to-solid ratio for attaining adequate workability and fiber dispersion. Nevertheless, the tensile strain capacity of LC 3 -based ECC achieved over 6% with an average residual crack width less than 50 μm. Additionally, the composite pore structure exhibited a decreasing volume fraction of large pores and voids (>100 nm) after substituting LC 3 for OPC. Here, the use of LC 3 marginally decreased the embodied material energy and cost, but led to about 32% and 28% reductions in CO 2 emissions compared to traditional OPC-based ECC and concrete, respectively. As a preliminary study, LC 3 -based ECC shows promise as a greener ductile concrete compared with OPC-based ECC.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Soil pore network response to freeze-thaw cycles in permafrost aggregates

This dataset contains data used for the paper "Pore network response to freeze-thaw cycles in permafrost aggregates". The Related References field will be updated with a full citation when available.Climate change in Arctic landscapes may increase freeze-thaw frequency within the active layer as well as newly thawed permafrost. A highly disruptive process, freeze-thaw can deform soil pores and alter the architecture of the soil pore network with varied impacts to water transport and retention, redox conditions, and microbial activity. Our objective was to investigate how freeze-thaw cycles impacted the pore network of newly thawed permafrost aggregates to improve understanding of what type of transformations can be expected from warming Arctic landscapes. We measured the impact of freeze-thaw on pore morphology, pore throat diameter distribution, and pore connectivity with X-ray computed tomography (XCT) using six permafrost aggregates with sizes of 2.5 cm3 from a mineral soil horizon (Bw; 28-50 cm depths) in Toolik, Alaska. Freeze-thaw cycles were performed using a laboratory incubation consisting of five freeze-thaw cycles (-10˚C to 20˚C) over five weeks. Our findings indicated decreasing spatial connectivity of the pore network across all aggregates with higher frequencies of singly connected pores following freeze-thaw. Water-filled pores that were connected to the pore network decreased in volume while the overall connected pore volumetric fraction was not affected. Shifts in the pore throat diameter distribution were mostly observed in pore throats ranges of 100 microns or less with no corresponding changes to the pore shape factor of pore throats. Responses of the pore network to freeze-thaw varied with aggregate, suggesting that initial pore morphology may play a role in driving freeze-thaw response. Our research suggests that freeze-thaw alters the microenvironment of permafrost aggregates during the incipient stage of deformation following permafrost thaw, impacting soil properties and function in Arctic landscapes undergoing transition. This dataset contains a compressed (.zip) archive of the data and R scripts used for this manuscript. The dataset includes files in .csv format, which can be accessed and processed using MS Excel or R. This archive can also be accessed on GitHub at https://github.com/Erin-Rooney/XCT-freezethaw (DOI: 10.5281/zenodo.5816355).

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1996

Effective Thermal Conductivity of an Aluminum Foam + Water Two Phase System

This study examined the effect of volume fraction and pore size on the effective thermal conductivity of an aluminum foam and water system. Nine specimens of aluminum foam representing a matrix of three volume fractions (4-8% by vol.) and three pore sizes (2-4 mm) were tested with water to determine relationships to the effective thermal conductivity. It was determined that increases in volume fraction of the aluminum phase were correlated to increases in the effective thermal conductivity. It was not statistically possible to prove that changes in pore size of the aluminum foam correlated to changes in the effective thermal conductivity. However, interaction effects between the volume fraction and pore size of the foam were statistically significant. Ten theoretical models were selected from the published literature to compare against the experimental data. Models by Asaad, Hadley, and de Vries provided effective thermal conductivity predictions within a 95% confidence interval.

Moskito, John↗

DOE OSTI2021

Deformation of pores in response to uniaxial and hydrostatic stress cycling in Marcellus Shale: Implications for gas recovery

One of the main challenges during gas production from shale reservoirs is low recovery rate. One contributing factor to this outcome is an insufficient understanding of pore systems, especially pore behaviour following changes in reservoir conditions or resulting from gas production practices. Because the pressure in the producing well can be controlled, understanding the effects of pressure variation on the pore size distribution and methane trapping is necessary to help design optimal conditions to improve the gas recovery rate. This work is the first systematic study of sub-millimeter pore deformation in shale caused by uniaxial and hydrostatic stress up to 100 MPa. Overmature samples from the Middle Devonian Marcellus Shale were analyzed using neutron scattering (SANS and USANS) techniques to interpret the response of nanopores to stress cycling of magnitude and duration compatible with the hydraulic fracturing treatments. Experiments reported here are performed at a series of uniaxial pressures up to 100 MPa and at hydrostatic pressures of deuterated methane 0 and 50 MPa. Since at the original depth of the shale samples’ burial of 2184 m the hydrostatic pressure is approximately 27 MPa and the lithostatic pressure is about 55 MPa, the experimental conditions reasonably well simulate the reservoir pressure regime. Our SANS and USANS results show that different pore sizes are affected by uniaxial stress in different ways. Specifically, in the pore size range from 1 nm to 800 nm, a decrease of pore density with pressure is observed, with the most depleted being mesopores of about 100 nm in diameter. The observed decrease is likely related to deformation of kerogen, followed by a loss of pore nano-volume, as well as methane trapped in the micropores. For pores larger than 5 μm, USANS data suggest that the negative trend is reversed at above 74 MPa, and the number density of large macropores may increase with increased stress even above the original value. The increased number of macropores at high pressure may create new interconnected conduits for gas migration, resulting in a better recovery rate. Another important finding of this study is an irreversible rearrangement of pore size distribution taking place after pressure cycling. Furthermore, this irreversible reorganization of pore size distribution should be taken into account during management of well production to maximize recovery rate.

03 NATURAL GAS↗

DOE OSTI2021

A mechanistic damage model for solid oxide fuel cell ceramic materials - Part I: Constitutive modeling

A multiscale mechanistic damage model for solid oxide fuel cell (SOFC) ceramics that combines micromechanics of stiffness reduction due to material porosity change and microcracking with a continuum damage mechanics (CDM) description for the evolution of microcracks up to fracture is developed in this work. The model also accounts for volumetric swelling of the anode due to redox cycling. Porosity change and swelling during redox combined with normal operating thermomechanical loads could increase the stress, strain and damage distributions in SOFC stacks leading them to failure. The proposed model involves three governing parameters: (i) the porosity in terms of the pore or void volume fraction, (ii) material swelling magnitude prescribed at a given loading step, and (iii) the damage variable that describes microcracking caused by thermomechanical loads and swelling. Pores and microcracks in the ceramics are modeled as randomly distributed ellipsoidal inclusions with negligible stiffness by an Eshelby-Mori-Tanaka formulation combined with an inclusion orientation distribution method. Microcracking damage evolution is described by a CDM formulation. Volumetric swelling is treated in a similar way to thermal expansion in the constitutive relations. After validation and numerical checks, the damage model is used to analyze a simplified SOFC positive-electrode/electrolyte/negative-electrode (PEN) structure subjected a redox cycle in addition to thermomechanical loads experienced during normal operation of a SOFC stack.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2026

Effects of confinement and pressure on the structure and dynamics of carbon dioxide in silica slit pores

An understanding of carbon dioxide fluid properties within geological mesopores is important in applications ranging from carbon sequestration to shale oil recovery. Here, a molecular dynamics study is presented that aims to shed light on these systems by simulation of CO 2 fluid confined in β-cristobalite silica slit pores with different pore widths and pressure conditions. The weakly associating nature of carbon dioxide leads to little difference in structural and interfacial dynamical properties for different pore sizes and pressures. Rather, the behavior is found to be dominated by the entropic effects, namely, how the CO 2 organizes next to the silica surface. The CO 2 self-diffusion coefficient shows the strongest pore size dependence. It is strongly diminished in small pores and does not reach the bulk fluid value even in 6 nm pores. It also decreases with pressure, yielding an activation volume that increases with pore size. These results provide new insight into the behavior of a compressible fluid in nanoscale confinement.

Godahewa, Sahan M. [Univ. of Kansas, Lawrence, KS ↗

DOE OSTI2022

A continuum damage approach to spallation and the role of microinertia

Spall failure is of interest due to its prevalence in high strain rate problems in which the spallation is driven by the interaction of release waves. In this article, a porosity-based damage model that includes microinertial effects is used to examine spall failure. The model is successfully calibrated to plate impact-driven experiments and then used to evaluate experimental conditions producing more extreme strain rate conditions, such as those in laser-driven experiments. The incorporation of microinertia allows us to better understand the increase in apparent macroscopic spall strength seen at high strain rates. Correspondingly, we conclude that the incorporation of microinertial effects improves the model’s predictive capabilities. Microinertial effects result in more severe local tensile stresses that affect the damage evolution, and microinertia can play a significant role in the approach to the material’s ideal strength at extreme loading rates. Additionally, a preliminary parametric study is also carried out to investigate the role of microstructural aspects such as nucleation volume fraction and initial pore radius. One counter-intuitive result from the microinertial effects is that, for a given nucleation site volume fraction, having larger initial pore nucleation sites can lead to an improved macroscopic spall strength.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Permeability-controlled migration of induced seismicity to deeper depths near Venus in North Texas

Abstract Migration of seismic events to deeper depths along basement faults over time has been observed in the wastewater injection sites, which can be correlated spatially and temporally to the propagation or retardation of pressure fronts and corresponding poroelastic response to given operation history. The seismicity rate model has been suggested as a physical indicator for the potential of earthquake nucleation along faults by quantifying poroelastic response to multiple well operations. Our field-scale model indicates that migrating patterns of 2015–2018 seismicity observed near Venus, TX are likely attributed to spatio-temporal evolution of Coulomb stressing rate constrained by the fault permeability. Even after reducing injection volumes since 2015, pore pressure continues to diffuse and steady transfer of elastic energy to the deep fault zone increases stressing rate consistently that can induce more frequent earthquakes at large distance scales. Sensitivity tests with variation in fault permeability show that (1) slow diffusion along a low-permeability fault limits earthquake nucleation near the injection interval or (2) rapid relaxation of pressure buildup within a high-permeability fault, caused by reducing injection volumes, may mitigate the seismic potential promptly.

58 GEOSCIENCES↗

DOE OSTI2026

Nanotomography for Pore Characterization

Tomographic characterization can provide accurate data on 3-dimensional characteristics of pore morphology such as connectivity, tortuosity, and volume thickness. Nanotomography can resolve pores in the 200 nm - 50 micrometer size range. In this work, the pore and solid networks of direct reduced iron (DRI) pellets in various states of reduction were analyzed to provide quantitative characterization of their transformation during reduction from ore to metal, and the influence of different reducing conditions on morphological characteristics.

36 MATERIALS SCIENCE↗