SEARCH · Engineering Papers

Results for “Plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1963

Radiant Heat Transfer to Absorbing Gases Enclosed Between Parallel Flat Plates with Flow and Conduction

An analysis is presented for obtaining two-dimensional temperature profiles and heat transfer in a radiation-absorbing gray gas of uniform absorptivity under the combined influence of thermal radiation, conduction, and gas flow. The gas is enclosed in a channel of infinite width and finite length formed by two semi-infinite parallel flat plates. These plates are black emitting surfaces, and the ends of the channel are formed by porous black surfaces through which the gas can flow into or out of the channel. These porous black end surfaces are used to simulate the radiation environment external to the channel. First, results are obtained for heat transfer between the plates in the absence of both conduction and flow. These results are found to be in good agreement with those obtained for the same conditions by previous workers. Results are then presented for heat transfer between the plates for the case of a radiating and conducting, but stagnant, gas separating the plates. The effects of the interactions between radiation and conduction are discussed. It was found that the heat transfer for combined radiation and conduction in an absorbing gas is slightly greater than the sum for each process taken separately. Finally, results are given for heat transfer from the plates to a flowing, radiating gas in the absence of conduction. The two plates are at the same temperature, and the gas enters the channel with uniform velocity and temperature. The results obtained for this case indicate that the heat transferred to the flowing gas from the constant temperature surfaces goes through a maximum as the absorptivity of the gas increases. This is in qualitative agreement with earlier results obtained by other investigators. All the results are presented in terms of dimensionless parameters, for the sake of generality, and the derivation of the dimensionless parameters, which are indicative of the effects of conduction and flow is presented.

Gray Gas↗

NASA NTRS1972

An experimental-theoretical study of free vibrations of plates on elastic point supports

A theoretical and experimental study is made to investigate the effect on plate vibrations of varying the stiffness of corner elastic point supports. A theoretical model is developed using a Rayleigh-Ritz analysis which approximates the plate mode shapes as products of free-free beam modes. The elastic point supports are modelled both as massless translational springs, and springs with tip masses. The tip masses are included to better represent the experimental supports. An experiment is constructed using the bending stiffness of horizontal beams to support a square plate at its four corners. The stiffness of these supports can be varied over such a range that the plate fundamental frequency is lowered to 40% of the rigid support frequency. The variation with support stiffness of the frequencies of the first eight plate modes is measured, and compared with the theoretical results. The plate mode shapes for rigid supports are analyzed using holographic interferometry. There is excellent agreement between the theoretical and experimental results, except for high plate modes where the theoretical model is demonstrated to be inadequate.

Leuner, T. R.↗

NASA NTRS1973

Vibration of thermally stressed plates with various boundary conditions.

By discarding Lurie's (1952) assumption of mode identity, it is shown that linear theory correctly predicts the frequency of all modes of a thermally stressed cantilever plate as well as the frequency and modes of plates with other boundary conditions. The thermal stress distribution is obtained for whatever temperature distribution and boundary conditions that may be specified. Experimental results are compared to calculated results for several different plates. Boundary conditions for the plates range from a plate with edges completely clamped to a plate with edges completely free with various other combinations of mixed and uniform edge conditions. Comparison of calculated data to experimental data shows that accurate, quantitative results can be obtained from linear theory for 'as cut' real plates for a significant range of heating when the assumption of mode identity is discarded.

Bailey, C. D.↗

NASA NTRS1976

Flutter and buckling of general laminated plates

An anisotropic buckling and flutter analysis is developed with allowance for both bending-extensional coupling and bending-twisting coupling within the framework of linear small deflection theory for simply supported general laminated plates. The extended Galerkin method is used to obtain approximate solutions to the coupled governing equations. The effects of various anisotropic stiffness parameters on the static and dynamic stability of laminated plates are evaluated, with particular emphasis on assessing the range of applicability of classical orthotropic plate theory. It is shown that bending-extensional coupling and bending-twisting stiffness terms have a destabilizing effect on buckling and flutter, the effect being more pronounced for a small number of layers. For symmetric plates, the number of layers required for orthotropic plate theory to be applicable is generally less for the buckling problem than for flutter. For square plates, aligning the fibers with the direction of airflow over the plate surface results in the highest flutter dynamic pressure.

Sawyer, J. W.↗

NASA NTRS1976

The nonlinear transient response of thin, rectangular elastic plates

The results of experiments and theoretical analysis of the nonlinear, transient response of thin, rectangular, elastic, simply supported plates are presented. In the experiments, a plane wave tube with a special pulse generator at one end and a thin glass plate mounted at the other end was used to subject the glass plate to pressure pulses of different magnitudes. Whole-field measurements of the response of the plate were obtained by the reflected moire grid technique. The largest ratio of center deflection to thickness of the plate during the experiments was 5.6. The theoretical response of the glass plate to the pressure pulses was computed by solving the von Karman equations governing large deflections in elastic plates by two methods - (1) the finite-difference method, and (2) Galerkin's method. Good agreement was found between theoretically predicted and experimentally measured response.

Rajagopal, G.↗

NASA NTRS1979

Design curves for non-linear analysis of simply-supported, uniformly-loaded rectangular plates

Design curves for the non-linear analysis of simply-supported rectangular plates subjected to uniform normal pressure loads have been developed. These curves yield the center deflection, center stress and corner stress in non-dimensionalized form plotted against a dimensionless parameter describing the load intensity. The results presented are based on extensive non-linear finite element analysis employing the ARGUS structural analysis program. Plates with length to width ratios of 1, 1.5, 2, 3 and 4 are included. The load range considered extends to 1000 times the load at which the behavior of the plate becomes significantly non-linear. Over the load range considered, the analysis shows that the ratio of center deflection to plate thickness for a square plate is less than 16 to 1, whereas linear theory would predict a center deflection 400 times the plate thickness. Likewise, the stress is markedly lower than would be predicted by linear theory. The present results are shown to be in excellent agreement with the classical linear theory up to a central deflection to plate thickness ratio of about one-half. In the non-linear regime the present results for deflection and stress are in very good agreement with the analytical and experimental work of other investigators.

Moore, D.↗

NASA NTRS1983

Propagating plane harmonic waves through finite length plates of variable thickness using finite element techniques

An analysis is given using finite element techniques which addresses the propagaton of a uniform incident pressure wave through a finite diameter axisymmetric tapered plate immersed in a fluid. The approach utilized in developing a finite element solution to this problem is based upon a technique for axisymmetric fluid structure interaction problems. The problem addressed is that of a 10 inch diameter axisymmetric fixed plate totally immersed in a fluid. The plate increases in thickness from approximately 0.01 inches thick at the center to 0.421 inches thick at a radius of 5 inches. Against each face of the tapered plate a cylindrical fluid volume was represented extending five wavelengths off the plate in the axial direction. The outer boundary of the fluid and plate regions were represented as a rigid encasement cylinder as was nearly the case in the physical problem. The primary objective of the analysis is to determine the form of the transmitted pressure distribution on the downstream side of the plate.

Clark, J. H.↗

NASA NTRS1983

Propagation of flexural and membrane waves with fluid loaded NASTRAN plate and shell elements

Modeling of flexural and membrane type waves existing in various submerged (or in vacuo) plate and/or shell finite element models that are excited with steady state type harmonic loadings proportioned to e(i omega t) is discussed. Only thin walled plates and shells are treated wherein rotary inertia and shear correction factors are not included. More specifically, the issue of determining the shell or plate mesh size needed to represent the spatial distribution of the plate or shell response is of prime importance towards successfully representing the solution to the problem at hand. To this end, a procedure is presented for establishing guide lines for determining the mesh size based on a simple test model that can be used for a variety of plate and shell configurations such as, cylindrical shells with water loading, cylindrical shells in vacuo, plates with water loading, and plates in vacuo. The procedure for doing these four cases is given, with specific numerical examples present only for the cylindrical shell case.

Kalinowski, A. J.↗

NASA NTRS1984

Multicolor printing plate joining

An upper plate having ink flow channels and a lower plate having a multicolored pattern are joined. The joining is accomplished without clogging any ink flow paths. A pattern having different colored parts and apertures is formed in a lower plate. Ink flow channels each having respective ink input ports are formed in an upper plate. The ink flow channels are coated with solder mask and the bottom of the upper plate is then coated with solder. The upper and lower plates are pressed together at from 2 to 5 psi and heated to a temperature of from 295 F to 750 F or enough to melt the solder. After the plates have cooled and the pressure is released, the solder mask is removed from the interior passageways by means of a liquid solvent.

Waters, W. J.↗

NASA NTRS1984

Vibrations of twisted cantilevered plates - Experimental investigation

The experimental portion of a joint government/industry/university research study on the vibrational characteristics of twisted cantilevered plates is presented. The overall purpose of the research study was to assess the capabilities and limitations of existing analytical methods in predicting the vibratory characteristics of twisted plates. Thirty cantilevered plates were precision machined at the Air Force's Aero Propulsion Laboratory. These plates, having five different degrees of twist, two thicknesses, and three aspect ratios representative of turbine engine blade geometries, were tested for their vibration mode shapes and frequencies. The resulting nondimensional frequencies and selected mode shapes are presented as a function of plate tip twist. The trends of the natural frequencies as a function of the governing geometric parameters are discussed. The effect of support compliance on the plate natural frequency and its impact on numerically modeling twisted plates is also presented.

Macbain, J. C.↗

NASA NTRS1985

An Elastic Analysis of a Plated Bone to Determine Fracture Gap Motion

An elastic analysis to determine fracture gap motions occurring in the osteotomized and plated canine femur was performed using the finite element program NASTRAN. The femur was idealized as a hollow right cylinder, and transverse anisotropy was assumed for the elastic properties of the bone. A 3-D 360 degree model consisting of 224 isoparametric quadrilateral hexahedral and 11 beam elements was created. A range of plate stiffnesses was tested by varying the modulus of elasticity of the plate from 207 GPa to 1 GPA. Moments were applied in the plane of the plate, about the axis of the plate, and in the plane of the screws. Results showed that, for plates of typical geometry and elastic modulus under 10 GPa, the contribution to fracture gap motion occurring due to deformation in the bone was negligible compared to that contribution from deformation in the plate.

Cooke, F. W.↗

NASA NTRS1985

Use of optimum stiffness tailoring to improve the compressive strength of composite plates with holes

A structural optimization procedure is used to tailor the cross-sectional stiffness distribution of compression-loaded composite plates with holes. Minimum mass designs are obtained for plates with cross sections consisting of two different balanced symmetric laminates with 0 deg, + or - 45 deg and 90 deg plies. The plate interior region contains the hole and is designed from a softer material system with a higher failure strain than the plate exterior region. All-graphite-epoxy plates and hybrid graphite/glass-epoxy plates were studied. Other designs with different percentages of 0 deg and + or 45 deg plies in the exterior laminate are compared with the optimum designs. Designs with uniform cross-sectional stiffnesses also are compared with the tailored cross-sectional stiffness designs. Specimens of each design were tested to verify the analytical predictions. The results show that cross-sectional stiffness tailoring can increase the compressive strength and decrease the mass of compression-loaded laminated plates with holes.

Haftka, R. T.↗

NASA NTRS1984

Heat transfer investigation in the junction region of circular cylinder normal to a flat plate at 90 deg location

External heat-transfer rates were measured on a flat plate in the junction region of a circular cylinder mounted normal to the plate at a location 90 deg from the stagnation point. This configuration simulates the junction of the shroud with gas-turbine vanes. Heat-transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.14 with gas temperatures of approximately 750 deg R over a flat plate at room temperature. The measurements were made in air for a unit Reynolds number, Re/cm, range of 11,000 to 58,000. Heat-transfer measurements were conducted in the 70-ft long, 4-in. diameter shock tube. A shock-wave reflection technique was used to produce a flow Mach number of 0.14. Thin-film platinum heat gages were mounted on the flat plate and along the line of the stagnation point of the cylinder to measure the local heat flux in the junction region. The experimental heat-transfer data were correlated with the laminar and turbulent boundary-layer theories for the flat plate. With the cylinder the heat fluxes on the flat plate were greatly increased in the junction region compared to the heat flux for the plate alone.

Nagamatsu, H. T.↗

NASA NTRS1987

Effects of transverse shearing flexibility on the postbuckling of plates loaded by inplane shear

This paper presents buckling and postbuckling results for plates loaded by inplane shear. The buckling results have been plotted to show the effects of thickness on the stress coefficient for aluminum plates. Results are given for various length-to-width ratios. Postbuckling results for thin plates with transverse shearing flexibility are compared to results from classical theory. The problems considered are the postbuckling response of plates in shear made of aluminum and of a + or - 45 deg graphite-epoxy laminate. Thus the materials are isotropic and orthotropic, respectively. The plates are considered to be long with side edges simply supported, with various inplane edge conditions, and the plates are subject to a constant shearing displacement along the side edges. Characteristic curves presenting the average shear stress resultant as a function of the applied displacement are given. These curves indicate that change in inplane edge conditions influence plate postbuckling stiffness and that transverse shearing is important in some cases.

Stein, Manuel↗

NASA NTRS1987

The effects of pin elasticity, clearance, and friction on the stresses in a pin-loaded orthotropic plate

The effects of pin elasticity, clearance, and friction on the stresses in a pin loaded orthotropic plate are studied. The effects are studied by posing the problem as a planar contact elasticity problem, the pin and the plate being two elastic bodies which interact through contact. Coulomb friction is assumed, the pin loads the plate in one of its principal material directions, and the plate is infinite in extent. A collocation scheme and interaction, in conjunction with a complex variable series solution, are used to obtain numerical results. The contact region between the plate and pin is unknown and must be solved for as part of the solution. The same is true of the region of friction induced no slip. Two pin stiffnesses, two clearance levels, two friction levels and two laminates, a (0/+ or - 45/90)s and a (02/+ or - 45)s, are studied. The effects of pin elasticity, clearance, and friction on the load capacity of the plate are assessed by comparing the load capacity of the plate with the capacity when the pin is rigid, perfectly fitting, and frictionless.

Hyer, M. W.↗

NASA NTRS1988

Impact induced stresses, strains, and delaminations in composite plates

A method is presented for calculating the locations and sizes of delaminations which occur in a rectangular, fiber reinforced composite plate subjected to nonpenetrating (low velocity) impact of a solid object. The plate may be simply supported or clamped along its edges. In-plane loads or in-plane strains may be imposed on the plate during the impact. The method includes two steps. First, the stresses and strains in the plate are calculated by a three-dimensional, transient finite element method using 8-node brick elements with incompatible modes. Second, the locations, lengths, and widths of delaminations inside the plate are predicted by means of a proposed failure criterion, which is based on the concept of dimensional analysis. The finite element method and the failure criterion were implemented by a computer code which can be used to calculate the impactor position and velocity, the displacements of the plate, the stresses and strains inside the plate during the impact, and the locations and dimensions of the delaminations after the impact. Parametric studies were performed to illustrate the information which can be generated by the computer code.

Wu, Hsi-Yung T.↗

NASA NTRS1989

Shear buckling of specially orthotropic plates with centrally located cutouts

The shear loading of a composite rectangular plate with a centrally located circular cutout was analyzed in order to predict the buckling load of the plate. The first step in this analysis is to calculare the in-plane stress distribution of the plate prior to buckling. This problem can be solved using finite element methods, but a quicker and more cost efficient method is desired. The method chosen to determine the pre-buckling stresses is that of boundary collocation using complex variables. The real valued force functions are written in terms of two complex valued functions, each of which is a function of a different complex variable. The solution of the generalized biharmonic function is a superposition of functions of these two complex variables. For this analysis, the force functions are represented with a Laurent series. The constants in these series are found using boundary collocation. Two force equations for complex variables are satisfied over the plate boundaries to obtain these constants. The stresses in the plate are then known for any particular locations on the plate given the applied shear on the edges of the plate.

Klang, Eric C.↗

NASA NTRS1990

Buckling and postbuckling behavior of compression-loaded isotropic plates with cutouts

An experimental study of the buckling and postbuckling behavior of square and rectangular compression loaded aluminum plates with centrally located circular, square, and elliptical cutouts is presented. Experimental results indicate that the plates exhibit overall trends of increasing buckling strain and decreasing initial postbuckling stiffness with increasing cutout width. Corresponding plates with circular and square cutouts of the same width buckle at approximately the same strain level, and exhibit approximately the same initial postbuckling stiffness. Results show that the reduction in initial postbuckling stiffness due to a cutout generally decreases as the plate aspect ratio increases. Other results presented indicate that square plates with elliptical cutouts having a large cutout-width-to-plate-width ratio generally lose prebuckling and initial postbuckling stiffness as the cutout height increases. However, the plates buckle at essentially the same strain level. Results also indicate that postbuckling stiffness is more sensitive to changes in elliptical cutout height than are prebuckling stiffness and buckling strain.

Nemeth, Michael P.↗