Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Active Q switching in a GaAs/AlGaAs multiquantum well laser with an intracavity monolithic loss modulator

Active Q switching in a GaAs/AlGaAs multiquantum well laser with an intracavity electroabsorption monolithic loss modulator is demonstrated. In this device, an efficient loss modulation is achieved through the quantum confined Stark effect in a modulator section and the enhanced carrier induced band shrinkage effect in an optical amplifier section. It is found that a picosecond pulse as narrow as 18.6 ps full width at half-maximum is generated and a high repetition rate of more than 3 GHz is obtained.

Arakawa, Y.↗
NASA NTRS1985

Picosecond excite-and-probe absorption measurement of the 4T2 state nonradiative lifetime in ruby

In a picosecond excite-and-probe absorption measurement, a 527-nm picosecond pulse excites the 4T2 state of the Cr(3+) ion in ruby and a 3.4-micron picosecond probe pulse monitors the growth and decay of population in the 2E state as a function of pump-probe delay. From the growth of population in the metastable 2E state, an upper limit of 7 ps for the nonradiative lifetime of the 4T2 state is determined.

Gayen, S. K.↗
NASA NTRS1986

Free vibration and dynamic response analysis of spinning structures

The proposed effort involved development of numerical procedures for efficient solution of free vibration problems of spinning structures. An eigenproblem solution procedure, based on a Lanczos method employing complex arithmetic, was successfully developed. This task involved formulation of the numerical procedure, FORTRAN coding of the algorithm, checking and debugging of software, and implementation of the routine in the STARS program. A graphics package for the E/S PS 300 as well as for the Tektronix terminals was successfully generated and consists of the following special capabilities: (1) a dynamic response plot for the stresses and displacements as functions of time; and (2) a menu driven command module enabling input of data on an interactive basis. Finally, the STARS analysis capability was further improved by implementing the dynamic response analysis package that provides information on nodal deformations and element stresses as a function of time. A number of test cases were run utilizing the currently developed algorithm implemented in the STARS program and such results indicate that the newly generated solution technique is significantly more efficient than other existing similar procedures.

Source record↗
NASA NTRS1986

Parallel scheduling of recursively defined arrays

A new method of automatic generation of concurrent programs which constructs arrays defined by sets of recursive equations is described. It is assumed that the time of computation of an array element is a linear combination of its indices, and integer programming is used to seek a succession of hyperplanes along which array elements can be computed concurrently. The method can be used to schedule equations involving variable length dependency vectors and mutually recursive arrays. Portions of the work reported here have been implemented in the PS automatic program generation system.

Myers, T. J.↗
NASA NTRS1987

Curvilinear ridges and related features in southwest Cydonia Mensae, Mars

Examined is a region on Mars in southwest Cydonia Mensae (32 deg lat., 17 deg long.) just northwest of the lowland/upland boundary escarpment. The dominant morphological features in this region are the clusters of large massifs and plateau outliers (PI), knobby material (K), and smooth lowland plains (Ps). Surrounding the clusters and linking many isolated knobs is a system of curvilinear ridges and arcuate terrain boundaries which tend to separate the massifs and knobs from the smooth plains. Curvilinear ridges are arcuate to nearly linear and smoother in plan than wrinkle ridges and show no apparent correlation with regional structural grain. They are typically 5 to 10 km long but can range from as little as 2 or 3 km to greater than 50 km long. The widths vary from about 100 m to as much as 2 km. Curvilinear ridges are most numerous within 100 km of the lowland/upland boundary escarpment and are associated with massifs and knobby terrain. Arcuate terrain boundaries appear between units of different apparent albedo or arcuate breaks in slope.

Parker, Timothy J.↗
NASA NTRS1986

Picosecond coherent anti-Stokes Raman scattering (CARS) study of vibrational dephasing of carbon disulfide and benzene in solution

The vibrational dephasing of the 656/cm mode (nu1, a1g) of CS2 and the 991/cm mode (nu2, a1g) of benzene have been studied as a function of concentration in mixtures with a number of solvents using a ps time-resolved CARS technique. This technique employs two tunable synchronously-pumped mode-locked dye lasers in a stimulated Raman pump, coherent anti-Stokes Raman probe time-resolved experiment. Results are obtained for CS2 in carbon tetrachloride, benzene, nitrobenzene, and ethanol and for benzene nu2 in CS2. The dephasing rates of CS2 nu1 increase on dilution with the polar solvents and decrease or remain constant on dilution with the nonpolar solvents. The CS2/benzene solutions show a contrasting behavior, with the CS2 nu1 dephasing rate being nearly independent of concentration whereas the benzene nu2 dephasing rate decreases on dilution. These results are compared to theoretical models for vibrational dephasing of polyatomic molecules in solution.

Perry, Joseph W.↗
NASA NTRS1986

Nonradiative relaxation in tunable solid state laser crystals

The characteristics of nonradiative transitions between the 4T2 and 2E excited states of trivalent-chromium-ion-activated ruby (containing 0.04 percent Cr2O3 by weight) and alexandrite (containing 0.4 at. percent chromium ion) laser crystals were studied using the technique described by Gayen et al. (1985). In this technique, a 527-nm pulse excites the 4T2 band of the Cr(3+), and the subsequent population kinetics among excited states is monitored by an IR picosecond probe pulse as a function of pump-probe delay. In ruby, a resolution-limited sharp rise in the excited state population was followed by a long-lifetime decay, leading to an upper limit of 7 ps for the 4T2-state nonradiative lifetime. In alexandrite, a longer rise time was followed by a multicomponent decay. A theoretical model is proposed for explaining the induced absorption and the transition dynamics observed in these crystals.

Gayen, S. K.↗
NASA NTRS1987

Time evolution of pulsed far-field patterns of GaAlAs phase-locked laser-diode arrays

The time evolution of pulsed far fields from commercially available gain-guided phase-locked arrays has been studied and compared to experimental results previously obtained by streak camera measurements, and to predictions of coupled-mode theories developed for index- and gain-guided arrays. Although phase locking is evident by 100 ps into the drive pulse, stable operation in a fixed superposition of array modes is not achieved until 1-2 ns after the drive pulse has stabilized.

Forrest, Kathrine A.↗
NASA NTRS1987

Development of optical modulators for measurements of solar magnetic fields

The measurement of polarized light allows solar astronomers to infer the magnetic field on the Sun. The accuracy of these measurements is dependent on the stable retardation characteristics of the polarization modulators used to minimize the atmospheric effects seen in ground-based observations. This report describes the work by the Space Science Laboratory at Marshall Space Flight Center to improve two types of polarization modulators. As a result, the timing characteristics for both electrooptic crystals (KD*Ps) and liquid crystal devices (LCDs) have been studied and will be used to enhance the capabilities of the MSFC Vector Magnetograph.

West, E. A.↗
NASA NTRS1987

Hot piston ring tests

As part of the DOE/NASA Automotive Stirling Engine Project, tests were made at NASA Lewis Research Center to determine whether appendix gap losses could be reduced and Stirling engine performance increased by installing an additional piston ring near the top of each piston dome. An MTI-designed upgraded Mod I Automotive Stirling Engine was used. Unlike the conventional rings at the bottom of the piston, these hot rings operated in a high temperature environment (700 C). They were made of a high temperature alloy (Stellite 6B) and a high temperature solid lubricant coating (NASA Lewis-developed PS-200) was applied to the cylinder walls. Engine tests were run at 5, 10, and 15 MPa operating pressure over a range of operating speeds. Tests were run both with hot rings and without to provide a baseline for comparison. Minimum data to assess the potential of both the hot rings and high temperature low friction coating was obtained. Results indicated a slight increase in power and efficiency, an increase over and above the friction loss introduced by the hot rings. Seal leakage measurements showed a significant reduction. Wear on both rings and coating was low.

Allen, David J.↗
NASA NTRS1987

Performance characteristics of InGaAs/GaAs and GaAs/InGaAlAs coherently strained superlattice photodiodes

The properties of In(0.24)Ga(0.76)As/GaAs and GaAs/In(0.05)Ga(0.58)Al(0.37)As superlattice photodiodes grown by molecular beam epitaxy have been investigated. From the temporal response characteristics, deconvolved rise times about 60-100 ps are obtained. The measured responsivities of the photodiodes with dark currents of 5-10 nA at 10 V are about 0.4 A/W, which correspond to peak external quantum efficiencies of about 60 percent. These results indicate that very high performance photodiodes can be realized with strained layers.

Das, Utpal↗
NASA NTRS1987

Delay line anodes for microchannel-plate spectrometers

A photon-counting readout system for microchannel-plate spectrometers is described that uses a delay line and timing circuit for the wavelength coordinate and a wedge-wedge charge division system for the orthogonal spatial coordinate. A novel zigzag layout allows these two anode patterns to coexist on a common planar substrate and share the charge from each photoevent, thereby simultaneously localizing the photon in each of its two dimensions. Unlike wedge-and-strip or resistive anode encoders, the delay line offers a spatial resolution that is relatively independent of the format length. Unlike discrete anode systems, the delay line readout system's complexity is also independent of the field of view size. These facts make the delay line readout system advantageous in large format detectors. A testbed detector having a delay line propagation speed of 2.2 mm/ns and a time resolution of 33 ps FWHM has been assembled. Ultraviolet testing shows a Gaussian event distribution having a 70-micron FWHM width; the readout system blur contribution is less than 50-micron FWHM.

Lampton, M.↗
NASA NTRS1988

Ultralow threshold graded-index separate-confinement heterostructure single quantum well (Al, Ga) As lasers

Broad area graded-index separate-confinement heterostructure single quantum well lasers grown by molecular-beam epitaxy (MBE) with threshold current density as low as 93 A/sq cm (520 microns long) have been fabricated. Buried lasers formed from similarly structured MBE material with liquid phase epitaxy regrowth had threshold currents at submilliampere levels when high reflectivity coatings were applied to the end facets. A CW threshold current of 0.55 mA was obtained for a laser with facet reflectivities of about 80 percent, a cavity length of 120 micron, and an active region stripe width of 1 micron. These devices driven directly with logic level signals have switch-on delays less than 50 ps without any current prebias. Such lasers permit fully on-off switching while at the same time obviating the need for bias monitoring and feedback control.

Derry, P. L.↗
NASA NTRS1989

Design And Analysis Of Optical Communication Links

To convey to prospective designers intuitive understanding based on unique characteristics of optical communication systems, report presents method of design and analysis of outer-space optical communication link using pulse-position modulation (PPM) and in which received signal sufficiently weak to require detection by photomultiplier operating in photon-counting mode. Step 1 requires some knowledge or assumptions about parameters of transmitter and receiver. Step 2 determination of average number of background-noise photons detected during PPM timeslot. Step 3 average number, Ps of signal photons detected per signal pulse compared with average number, Pn of noise pulses detected per PPM timeslot.

Lesh, J. R.↗
NASA NTRS1988

Synchronously pumped mode-locked Ti:Al2O3 lasers

Synchronously pumped mode-locked laser operation in a Ti:Al2O3 ring laser is demonstrated. The laser pump source was a frequency-doubled Nd:YAG laser-amplifier system producing a 60-micron-long macropulse that comprised a wavetrain of mode-locked 70-ps micropulses with a 10-ns spacing (100 MHz). The Ti:Al2O3 laser consisted of a 1-cm-long crystal with faces cut at the Brewster angle and placed in a ring laser cavity configuration with a 2 percent output coupling mirror. The cavity was adjusted for a 5-ns round trip transit time, which was close to half the temporal spacing of the pump pulse. When the crystal was pumped synchronously at 532 nm with a 30-mJ macropulse, which was approximately an order of magnitude above the laser threshold, mode-locked lasing at approximately 200 MHz was obtained. This macropulse pump energy corresponds to an average micropulse pump energy of about 5 microJ at the Ti:Al2O3 crystal face. The mode-locked operation of the Ti:Al2O3 was observed only after several microseconds into the macropulse, indicating a long build-up process over many cavity trips. During this time, relaxation oscillations were observed. When mode locking started, the relaxation oscillation frequency increased by an order of magnitude. Synchronous pumping has been limited to operation with dye lasers and used either a CW or pulsed mode-locked pump source. Recent work has demonstrated CW mode-locked operation of a Ti:Al2O3 laser. The result raises the possibility that pulsed synchronous pumping may be used to obtain significantly narrowed laser pulses in Ti:Al2O3.

Source record↗
NASA NTRS1988

Transient photoconductivity in the ferromagnetic semiconductor CdCr2Se4

The transient photoconductive response time of the ferromagnetic semiconductor CdCr2Se4 was measured to be smaller than 90 ps, the response time of the scope. The measurements were performed at room temperature (300 K) for 0.53 and 1.06 microns excitations using a mode locked frequency-doubled YAG laser.

Walser, A. D.↗
NASA NTRS1989

Angular navigation on short baselines using phase delay interferometry

Results are presented for two recent short baseline experiments, with baseline lengths of 6 and 253 km, showing delay residuals of 10 ps or less for angularly close sources. On the 6-km baseline, a fiber-optic link was used to distribute a common frequency reference, enabling coherent operation of the two stations. The observed delay residuals correspond to a differential angular accuracy of about 10 nrad on the 253-km baseline. Future plans are discussed, including the development of a realtime correlation capability on a 22-km baseline at Goldstone, CA.

Edwards, Charles D.↗
NASA NTRS1989

Evaluation of a metering, mixing, and dispensing system for mixing polysulfide adhesive

Tests were performed to evaluate whether a metered mixing system can mix PR-1221 polysulfide adhesive as well as or better than batch-mixed adhesive; also, to evaluate the quality of meter-mixed PR-1860 and PS-875 polysulfide adhesives. These adhesives are candidate replacements for PR-1221 which will not be manufactured in the future. The following material properties were evaluated: peel strength, specific gravity and adhesive components of mixed adhesives, Shore A hardness, tensile adhesion strength, and flow rate. Finally, a visual test called the butterfly test was performed to observe for bubbles and unmixed adhesive. The results of these tests are reported and discussed.

Evans, Kurt B.↗