Results for “Materials Characterization Technique” — Page 11

NASA NTRSDate not supplied

ASTM International Conference on Additive Manufacturing – 2022

The In-Situ Project: Correlating In-situ monitoring data and Non-Destructive Evaluation (NDE) methods to characterize defect populations in Laser Powder Bed Fusion (L-PBF) material NDE is critical to enable the safe use of additive manufactured (AM) parts in aerospace applications. However, traditional NDE methods are not fully adaptable to complex AM geometries to appropriately screen for critical defects, and L-PBF processes inherently generate defects. In-situ monitoring techniques can give information about the quality of the build process and indicate process variations that could potentially create defects. Proven, causal correlations between in-situ monitoring indications and resulting defects are needed to inform about the final quality of the part. Thus, the development of a new approach is necessary. NASA started a two-phase study that would investigate techniques for characterizing defect populations in L-PBF material, first in material with induced defects, then in a nominal L-PBF process, by correlating in-situ, NDE, and serial sectioning data. Objectives also include the evaluation of seeded defect methodologies for realistic defect creation, creating a baseline of defect populations in a Qualified Material Process (QMP), characterizing the effect of heat treatment, and correlating defect populations with tensile and fatigue properties. By comparing computed tomography images, in-situ monitoring images, and metallography images, the team has been able to draw preliminary conclusions. They include a better understanding of the limitation of the NDE tools, learning about the “healing” of the samples observed during layer building and a comparison study on different laser power variation samples. Those preliminary conclusions will help dictate the follow-up work that will be presented at the conference.

additive manufacturing↗

NASA NTRS1994

The effect of Low Earth Orbit exposure on some experimental fluorine and silicon-containing polymers

Several experimental fluorine and silicon-containing polymers in film form were exposed to low Earth orbit (LEO) on a Space Shuttle flight experiment (STS-46, Evaluation of Oxygen Interaction with Materials, EOIM-3). The environmental parameters of primary concern were atomic oxygen (AO) and ultraviolet (UV) radiation. The materials were exposed to 2.3 plus or minus 0.1 x 10(exp 20) oxygen atoms/sq cm and 30.6 UV sun hours during the flight. In some cases, the samples were exposed at ambient, 120 C and 200 C. The effects of exposure on these materials were assessed utilizing a variety of characterization techniques including optical, scanning electron (SEM) and scanning tunneling (STM) microscopy, UV-visible (UV-VIS) transmission, diffuse reflectance infrared (DR-FTIR), x-ray photoelectron (XPS) spectroscopy, and in a few cases, gel permeation chromatography (GPC). In addition, weight losses of the films, presumably due to AO erosion, were measured. The fluorine-containing polymers exhibited significant AO erosion and exposed films were diffuse or 'frosted' in appearance and consequently displayed dramatic reductions in optical transmission. The silicon-containing films exhibited minimum AO erosion and the optical transmission of exposed films was essentially unchanged. The silicon near the exposed surface in the films was converted to silicate/silicon oxide upon AO exposure which subsequently provided protection for the underlying material. The silicon-containing epoxies are potentially useful as AO resistant coatings and matrix resins as they are readily processed into carbon fiber reinforced composites and cured via electron radiation.

Connell, John W.↗

NASA NTRS2019

Additive Manufacturing Development and Hot-Fire Testing of Liquid Rocket Channel Wall Nozzles Using Blown Powder Directed Energy Deposition Inconel 625 and JBK-75 Alloys

Additive manufacturing (AM) is being investigated at NASA and across much of the rocket propulsion industry as an alternate fabrication technique to create complex geometries for liquid engine components that offers schedule and cost saving opportunities. The geometries that can be created using AM offer a significant advantage over traditional techniques. Internal complexities, such as internal coolant channels for combustion chambers and nozzles that would typically require several operations to manufacture traditionally can be fabricated in one process. Additionally, the coolant channels are closed out as a part of the AM build process, eliminating the complexities of a traditional process like brazing or plating. The primary additive manufacturing technique that has been evaluated is powder bed fusion (PBF), or selective laser melting (SLM), but there is a scale limitation for this technique. There are several alternate additive manufacturing techniques that are being investigated for large-scale nozzles and chambers including directed energy deposition (DED) processes. A significant advantage of the DED processes is the ability to adapt to a robotic or gantry CNC system with a localized purge or purge chamber, allowing unlimited build volume. This paper will discuss the development and hot-fire testing of channel-cooled nozzles fabricated utilizing one form of DED called blown powder deposition. This initial development work using blown powder DED is being explored to form the entire channel wall nozzle with integral coolant channels within a single AM build. Much of this development is focused on the design and DED-fabrication of complex and thin-walled features and on characterization of the materials properties produced with this techniques in order to evolve this process. Subscale nozzles were fabricated using this DED technique and hot-fire tested in Liquid Oxygen/Hydrogen (LOX/GH2) and LOX/Kerosene (LOX/RP-1) environments accumulating significant development time and cycles. The initial materials that were evaluated during this testing were high-strength nickel-based Inconel 625 and JBK-75. Further process development is being completed to increase the scale of this technology for large-scale nozzles. This paper will summarize the general design considerations for DED, specific channel-cooled nozzle design, manufacturing process development, property development, initial hot-fire testing and future developments to mature this technology for regeneratively-cooled nozzles. An overview of future development at NASA will also be discussed.

Gradl, Paul R.↗

NASA NTRSDate not supplied

Orion Artemis I As Flown MMOD Analysis

Introduction The Lockheed Martin Orion spacecraft conducted the Artemis I flight around the Moon from November 16 through December 11, 2022. After the flight, an engineer from the NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) Group performed a Micrometeoroid and Orbital Debris MMOD analysis using the Bumper 3 risk assessment tool to predict the number of small impacts that would likely have occurred during the mission. Separately, a team from the same group inspected the Orion capsule for hypervelocity impact damage features. The results of the inspection were compared to those of the analysis to aid in improving the analysis, including the environment models. Scope of Work The spacecraft geometry model was created by Lockheed Martin during construction of the Artemis I Orion vehicle based on Computer Aided Design (CAD) models of the vehicle. New hypervelocity impact testing was performed to verify Ballistic Limit Equations (BLEs) used in the analysis to link impactor size and damage to the Thermal Protection System (TPS). The exact trajectory flown was recorded during the flight, including vehicle attitude. This data was used in conjunction with the ORDEM 3.2 and MEM 3 environment modeling tools to create models of particle flux impacting the spacecraft throughout the mission. Meteoroid shower forecast information was also included to account for additional particle flux associated with meteoroid showers. Inspection of the Orion capsule included the Backshell thermal tiles and the tape covering it, windows, fabric thermal materials, and small areas of other materials. Potential MMOD damage found was characterized using various techniques, including optical microscopy, computed tomography scanning, and X-ray spectroscopy. Findings The number of craters found in the Backshell tile, and their size distribution, matches well with the Bumper analysis prediction. Tape, window, and other material impacts recorded similarly align to Bumper analysis predictions. Conclusions and Recommendations This comparison of analysis with inspection of the hardware provides valuable insight into the MMOD environment and how accurately analysis tools assess the impact risk to spacecraft. As this was the first large, non-ablative returned surface from a lunar mission, this analysis extends the MMOD community’s insight beyond low Earth orbit into cis-lunar space.

MMOD↗

NASA NTRSDate not supplied

Orion Artemis I As Flown MMOD Analysis

Introduction The Lockheed Martin Orion spacecraft conducted the Artemis I flight around the Moon from November 16 through December 11, 2022. After the flight, an engineer from the NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) Group performed a Micrometeoroid and Orbital Debris MMOD analysis using the Bumper 3 risk assessment tool to predict the number of small impacts that would likely have occurred during the mission. Separately, a team from the same group inspected the Orion capsule for hypervelocity impact damage features. The results of the inspection were compared to those of the analysis to aid in improving the analysis, including the environment models. Scope of Work The spacecraft geometry model was created by Lockheed Martin during construction of the Artemis I Orion vehicle based on Computer Aided Design (CAD) models of the vehicle. New hypervelocity impact testing was performed to verify Ballistic Limit Equations (BLEs) used in the analysis to link impactor size and damage to the Thermal Protection System (TPS). The exact trajectory flown was recorded during the flight, including vehicle attitude. This data was used in conjunction with the ORDEM 3.2 and MEM 3 environment modeling tools to create models of particle flux impacting the spacecraft throughout the mission. Meteoroid shower forecast information was also included to account for additional particle flux associated with meteoroid showers. Inspection of the Orion capsule included the Backshell thermal tiles and the tape covering it, windows, fabric thermal materials, and small areas of other materials. Potential MMOD damage found was characterized using various techniques, including optical microscopy, computed tomography scanning, and X-ray spectroscopy. Findings The number of craters found in the Backshell tile, and their size distribution, matches well with the Bumper analysis prediction. Tape, window, and other material impacts recorded similarly align to Bumper analysis predictions. Conclusions and Recommendations This comparison of analysis with inspection of the hardware provides valuable insight into the MMOD environment and how accurately analysis tools assess the impact risk to spacecraft. As this was the first large, non-ablative returned surface from a lunar mission, this analysis extends the MMOD community’s insight beyond low Earth orbit into cis-lunar space.

MMOD↗

NASA NTRS2018

Printed Circuit Board Inspection and Quality Control - PCB Failure Causes and Cures

This two day workshop will discuss a range of topics, including root cause analysis, physics-of-failure principles and failure mechanisms in printed circuit boards. Printed circuit boards (PCBs) are the baseline for electronics manufacturing upon which electronic components are mounted and formed into electronic systems. PCBs are used in a variety of electronic circuits from simple one-transistor amplifiers to large super computers. A PCB serves three main functions: 1) it provides the necessary mechanical support for the components in the circuit 2) it provides the necessary electrical interconnections, and 3) it bears some form of legend which identifies the components it carries. The failure modes on the PCBs can be categorized in a hierarchical structure, in which the mechanisms and causes are site or location dependant. Specimen preparation techniques, non-destructive and destructive analysis, and materials characterization will also be discussed. The first day of the workshop will present methodologies for identifying potential failure mechanisms in electronics based on the failure history and, systematic approaches to root cause analysis. The second day will cover failure analysis techniques geared towards various failure mechanisms, along with numerous component and PCB assembly failure analysis case studies that illustrate the techniques and analysis. Failure analysis case studies will be used to illustrate the techniques and analysis principles to arrive at the root cause(s) of field failures on printed circuit boards, active components, and assemblies.

Printed circuit boards↗

DOE OSTI2024

X-ray linear dichroic tomography of crystallographic and topological defects

Abstract The functionality of materials is determined by their composition 1–4 and microstructure, that is, the distribution and orientation of crystalline grains, grain boundaries and the defects within them 5,6 . Until now, characterization techniques that map the distribution of grains, their orientation and the presence of defects have been limited to surface investigations, to spatial resolutions of a few hundred nanometres or to systems of thickness around 100 nm, thus requiring destructive sample preparation for measurements and preventing the study of system-representative volumes or the investigation of materials under operational conditions 7–15 . Here we present X-ray linear dichroic orientation tomography (XL-DOT), a quantitative, non-invasive technique that allows for an intragranular and intergranular characterization of extended polycrystalline and non-crystalline 16 materials in three dimensions. We present the detailed characterization of a polycrystalline sample of vanadium pentoxide (V 2 O 5 ), a key catalyst in the production of sulfuric acid 17 . We determine the nanoscale composition, microstructure and crystal orientation throughout the polycrystalline sample with 73 nm spatial resolution. We identify and characterize grains, as well as twist, tilt and twin grain boundaries. We further observe the creation and annihilation of topological defects promoted by the presence of volume crystallographic defects. The non-destructive and spectroscopic nature of our method opens the door to operando combined chemical and microstructural investigations 11,18 of functional materials, including energy, mechanical and quantum materials.

Science & Technology - Other Topics↗

NASA NTRS2007

Application of Raman Spectroscopy for Nondestructive Evaluation of Composite Materials

This paper will present an overview of efforts to investigate the application of Raman spectroscopy for the characterization of Kevlar materials. Raman spectroscopy is a laser technique that is sensitive to molecular interactions in materials such as Kevlar, graphite and carbon used in composite materials. The overall goal of this research reported here is to evaluate Raman spectroscopy as a potential nondestructive evaluation (NDE) tool for the detection of stress rupture in Kevlar composite over-wrapped pressure vessels (COPVs). Characterization of the Raman spectra of Kevlar yarn and strands will be presented and compared with analytical models provided in the literature. Results of testing to investigate the effects of creep and high-temperature aging on the Raman spectra will be presented.

Washer, Glenn A.↗

NASA NTRS1976

Development of a high capacity bubble domain memory element and related epitaxial garnet materials for application in spacecraft data recorders. Item 2: The optimization of material-device parameters for application in bubble domain memory elements for spacecraft data recorders

Bubble domain materials and devices are discussed. One of the materials development goals was a materials system suitable for operation of 16 micrometer period bubble domain devices at 150 kHz over the temperature range -10 C to +60 C. Several material compositions and hard bubble suppression techniques were characterized and the most promising candidates were evaluated in device structures. The technique of pulsed laser stroboscopic microscopy was used to characterize bubble dynamic properties and device performance at 150 kHz. Techniques for large area LPE film growth were developed as a separate task. Device studies included detector optimization, passive replicator design and test and on-chip bridge evaluation. As a technology demonstration an 8 chip memory cell was designed, tested and delivered. The memory elements used in the cell were 10 kilobit serial registers.

Besser, P. J.↗

NASA NTRS1977

Kinetic studies of stress-corrosion cracking

Use of time-to-failure curves for stress-corrosion cracking processes may lead to incorrect estimates of structural life, if material is strongly dependent upon prestress levels. Technique characterizes kinetics of crackgrowth rates and intermediate arrest times by load-level changes.

Noronha, P. J.↗

NASA NTRS1981

Ultrasonic frequency analysis

Technique is used for evaluation and characterization of materials, fluids, and biological tissue. Method eliminates problem of electrical drive pulse shape by slaving tracking generator to local oscillator of spectrum analyzer. Logic/timing generator is used to control pulse transmission and receiving sequence, pulse width, and pulse repetition rate.

Cantrell, J. H.↗

NASA NTRS1980

The accelerated characterization of viscoelastic composite materials

Necessary fundamentals relative to composite materials and viscoelasticity are reviewed. The accelerated characterization techniques of time temperature superposition and time temperature stress superposition are described. An experimental procedure for applying the latter to composites is given along with results obtained on a particular T300/934 graphite/epoxy. The accelerated characterization predictions are found in good agreement with actual long term tests. A postcuring phenomenon is discussed that necessitates thermal conditioning of the specimen prior to testing. A closely related phenomenon of physical aging is described as well as the effect of each on the glass transition temperature and strength. Creep rupture results are provided for a variety of geometries and temperatures for T300/934 graphite/epoxy. The results are found to compare reasonably with a modified kinetic rate theory.

Griffith, W. I.↗

NASA NTRS1981

The growth of metastable peritectic compounds

The influence of gravitationally driven thermosolutal convection on the directional solidification of peritectic alloys is considered as well as the relationships between the solidification processing conditions, and the microstructure, chemistry, and magnetic properties of such alloys. Analysis of directionally solidified Pb-Bi peritectic samples indicates that appreciable macrosegregation occurs due to thermosolutal convection and/or Soret diffusion. A peritectic solidification model which accounts for partial mixing in the liquid ahead of the planar solidification interface and describes macrosegregation has been developed. Two-phase dendritic and banded microstructures were grown in the Pb-Bi peritectic system, refined two-phase microstructures have were observed, and candidate formation mechanisms proposed. Material handling, containment, casting, microstructural and magnetic characterization techniques were developed for the Sm-Co system. Alloys produced with these procedures are homogeneous.

Larson, D. J., Jr.↗

NASA NTRS1991

NDE of ceramics and ceramic composites

Although nondestructive evaluation (NDE) techniques for ceramics are fairly well developed, they are difficult to apply in many cases for high probability detection of the minute flaws that can cause failure in monolithic ceramics. Conventional NDE techniques are available for monolithic and fiber reinforced ceramic matrix composites, but more exact quantitative techniques needed are still being investigated and developed. Needs range from flaw detection to below 100 micron levels in monolithic ceramics to global imaging of fiber architecture and matrix densification anomalies in ceramic composites. NDE techniques that will ultimately be applicable to production and quality control of ceramic structures are still emerging from the lab. Needs are different depending on the processing stage, fabrication method, and nature of the finished product. NDE techniques are being developed in concert with materials processing research where they can provide feedback information to processing development and quality improvement. NDE techniques also serve as research tools for materials characterization and for understanding failure processes, e.g., during thermomechanical testing.

Vary, Alex↗

NASA NTRS1993

NDE of ceramics and ceramic composites

Although nondestructive evaluation (NDE) techniques for ceramics are fairly well developed, they are difficult to apply in many cases for high probability detection of the minute flaws that can cause failure in monolithic ceramics. Conventional NDE techniques are available for monolithic and fiber reinforced ceramic matrix composites, but more exact quantitative techniques needed are still being investigated and developed. Needs range from flaw detection to below 100 micron levels in monolithic ceramics to global imaging of fiber architecture and matrix densification anomalies in ceramic composites. NDE techniques that will ultimately be applicable to production and quality control of ceramic structures are still emerging from the lab. Needs are different depending on the processing stage, fabrication method, and nature of the finished product. NDE techniques are being developed in concert with materials processing research where they can provide feedback information to processing development and quality improvement. NDE techniques also serve as research tools for materials characterization and for understanding failure processes, e.g., during thermomechanical testing.

Vary, Alex A.↗

NASA NTRS1997

Physics and Process Modeling (PPM) and Other Propulsion R and T: Materials Processing, Characterization, and Modeling; Lifting Models - Volume 1

This CP contains the extended abstracts and presentation figures of 36 papers presented at the PPM and Other Propulsion R&T Conference. The focus of the research described in these presentations is on materials and structures technologies that are parts of the various projects within the NASA Aeronautics Propulsion Systems Research and Technology Base Program. These projects include Physics and Process Modeling; Smart, Green Engine; Fast, Quiet Engine; High Temperature Engine Materials Program; and Hybrid Hyperspeed Propulsion. Also presented were research results from the Rotorcraft Systems Program and work supported by the NASA Lewis Director's Discretionary Fund. Authors from NASA Lewis Research Center, industry, and universities conducted research in the following areas: material processing, material characterization, modeling, life, applied life models, design techniques, vibration control, mechanical components, and tribology. Key issues, research accomplishments, and future directions are summarized in this publication.

Source record↗

NASA NTRS2005

Characterizing the Chemical Stability of High Temperature Materials for Application in Extreme Environments

The chemical stability of high temperature materials must be known for use in the extreme environments of combustion applications. The characterization techniques available at NASA Glenn Research Center vary from fundamental thermodynamic property determination to material durability testing in actual engine environments. In this paper some of the unique techniques and facilities available at NASA Glenn will be reviewed. Multiple cell Knudsen effusion mass spectrometry is used to determine thermodynamic data by sampling gas species formed by reaction or equilibration in a Knudsen cell held in a vacuum. The transpiration technique can also be used to determine thermodynamic data of volatile species but at atmospheric pressures. Thermodynamic data in the Si-O-H(g) system were determined with this technique. Free Jet Sampling Mass Spectrometry can be used to study gas-solid interactions at a pressure of one atmosphere. Volatile Si(OH)4(g) was identified by this mass spectrometry technique. A High Pressure Burner Rig is used to expose high temperature materials in hydrocarbon-fueled combustion environments. Silicon carbide (SiC) volatility rates were measured in the burner rig as a function of total pressure, gas velocity and temperature. Finally, the Research Combustion Lab Rocket Test Cell is used to expose high temperature materials in hydrogen/oxygen rocket engine environments to assess material durability. SiC recession due to rocket engine exposures was measured as a function of oxidant/fuel ratio, temperature, and total pressure. The emphasis of the discussion for all techniques will be placed on experimental factors that must be controlled for accurate acquisition of results and reliable prediction of high temperature material chemical stability.

Opila, Elizabeth↗

NASA NTRS2006

Arc-Heater Facility for Hot Hydrogen Exposure of Nuclear Thermal Rocket Materials

A hyper-thermal environment simulator is described for hot hydrogen exposure of nuclear thermal rocket material specimens and component development. This newly established testing capability uses a high-power, multi-gas, segmented arc-heater to produce high-temperature pressurized hydrogen flows representative of practical reactor core environments and is intended to serve. as a low cost test facility for the purpose of investigating and characterizing candidate fueUstructura1 materials and improving associated processing/fabrication techniques. Design and development efforts are thoroughly summarized, including thermal hydraulics analysis and simulation results, and facility operating characteristics are reported, as determined from a series of baseline performance mapping tests.

Litchford, Ron J.↗