Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Launcher”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Efficient ECCD non-inductive plasma current start-up, ramp-up, and sustainment for an ST fusion reactor

The elimination of the need for an Ohmic heating solenoid may be the most impactful design driver for the realization of economical compact fusion tokamak reactor systems. However, this would require fully non-inductive start-up and current ramp-up from zero plasma current and low electron temperature of sub-keV to the full plasma current of ~10–15 MA at 20–30 keV electron temperature. To address this challenge, an efficient solenoid-free start-up and ramp-up scenario utilizing a low-field-side-launched extraordinary mode at the fundamental electron cyclotron harmonic frequency (X–I) is proposed, which has more than two orders of magnitude higher electron cyclotron current drive (ECCD) efficiency than the conventional ECCD for the sub-keV start-up regime. A time dependent model was developed to simulate the start-up scenarios. For the Spherical Tokamak Advanced Reactor (STAR) (Menard et al 2023 Next-Step Low-Aspect-Ratio Tokamak Design Studies (IAEA)), it was found that to fully non-inductively ramp-up to 15 MA, it would take about 25 MW of EC power at 170 GHz. Because of the relatively large plasma volume of STAR, radiation losses must be considered. It is important to make sure that high Z impurities are kept sufficiently low during the early current start-up phase where the temperature is sub-keV range. Since the initial current ramp up takes place at a factor of ten lower density compared to the sustained regimes, it is important to transition into a higher bootstrap fraction discharge at lower density to minimize the ECCD power requirement during the densification. For the sustainment phase an array of eight gyrotron launchers with a total of about 60 MW of fundamental O-mode was found to be sufficient to provide the required axis-peaked external current drive. High efficiencies between 19–57 kA MW –1 were found with optimal aiming, and these were resilient to small changes in aiming angles and density and temperature profiles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Auxiliary heating and current drive physics for the ST-E1 fusion power plant

This work describes the physics basis for the proposed auxiliary heating and current drive system on the ST-E1 fusion power plant. The ST-E1 flattop plasma considered here is fully non-inductive with a bootstrap fraction of 0.9 and the remaining current driven by EC waves. Using the recently published physics-based optimization method for EC launchers (Lopez et al 2025 Plasma Phys. Control. Fusion 67 055012), we show that the target flattop ECCD can be achieved with a net efficiency of 52 kA MW −1 using fundamental O-mode (O1) with frequency range 160–200 GHz launched from the low-field side top half of the vacuum vessel (LFS top-launch). From considering two candidate rampup scenarios, we conclude that LFS top-launch O1 ECCD can be equally effective during the early stages of plasma operation, although poloidal steering might be needed. X-mode waves injected from the LFS midplane are also shown to be effective for rampup even when T e < 1 keV. We also present modeling results for the pre-conceptual design of an ICRH system proposed for ST-E1. Using TORIC, we find that an ICRH system aiming for 42–48 MHz and toroidal mode number n φ ~ 10 robustly achieves dominant ion damping via Helium-3 minority heating transitioning to second-harmonic Tritium heating. We then show that such waves can be efficiently generated by a 5-strap traveling-wave antenna (TWA) using the Petra-M code. The TWA has a 40–45 MHz passband within which ~60% of the power entering the TWA is coupled to the plasma with the remaining ~40% of the power being transmitted through the TWA and possibly recirculated; the power reflected back into the transmission lines is negligible. This passband structure persists even when the evanescent distance is increased by a factor of two, or when the magnetic-field angle is increased by 30°, demonstrating inherent load resilience that will be crucial for effective ICRH on ST-E1.

electron cyclotron↗
DOE OSTI2025

Integrating and Characterizing HPC Task Runtime Systems for hybrid AI-HPC workloads

Scientific workflows increasingly involve both HPC and machine-learning tasks, combining MPI-based simulations, training, and inference in a single execution. Launchers such as Slurm’s srun constrain concurrency and throughput, making them unsuitable for dynamic and heterogeneous workloads. We present a performance study of RADICAL-Pilot (RP) integrated with Flux and Dragon, two complementary runtime systems that enable hierarchical resource management and high-throughput function execution. Using synthetic and production-scale workloads on Frontier, we characterize the task execution properties of RP across runtime configurations. RP+Flux sustains up to 930 tasks/s, and RP+Flux+Dragon exceeds 1,500 tasks/s with over 99.6% utilization. In contrast, srun peaks at 152 tasks/s and degrades with scale, with utilization below 50%. For IMPECCABLE.v2 drug discovery campaign, RP+Flux reduces makespan by 30–60% relative to srun/Slurm and increases throughput more than four times on up to 1,024. These results demonstrate hybrid runtime integration in RP as a scalable approach for hybrid AI-HPC workloads.

HPC-AI↗
DOE OSTI2025

Impact Testing Theories and Techniques Employed at the TA-III Mechanical Shock Complex

We present theories and techniques to support safe, predictable, and efficient impact testing at the Sandia National Laboratories TA-III Mechanical Shock Complex (MSC), located in Building 6570. The two testing instruments used at the MSC are the 20-inch actuator, which is a launcher that propels sleds down an indoor track, and an indoor 6-in bore compressed-gas powered cannon. The theories and techniques presented derive from basic mechanical engineering principles but are significantly informed and validated by testing experience at the MSC.

42 ENGINEERING↗
NASA NTRS1968

Propulsion Division

Ballistic launchers, polymer materials for space applications, heat transfer studies of ionized gases, thermionic diode kinetics, liquid metal mhd power conversion, and liquid propulsion

Source record↗
NASA NTRS1966

Postflight Evaluation of Atlas-Centaur AC-6 (Launched August 11, 1965)

The sixth Atlas Centaur vehicle (AC-6) was successfully launched from the Eastern T e s t Range, Complex 36B, on August 11, 1965, at 0931:04.430 EST. A 2084-pound dynamic model of the Surveyor payload was placed in a simulated lunar transfer trajectory. Vehicle systems operated satisfactorily and all the flight objectives were accomplished. Lift-off within 4 seconds of the window opening demonstrated the launch-on-time capability of the vehicle were accurately compensated for by the Centaur guidance system. the Surveyor model into a near-perfect lunar transfer trajectory would have resulted in an impact of the moon without a midcourse correction. To hit the precise target area on the lunar surface, the required correction would have been 4.25 meters per second, which is well within the spacecraft capability. Normal thrust and impulse levels were obtained with both the A t l a s and Centaur propulsion systems. However, a sizeable thrust overshoot on startup of the Centaur engines has not been resolved. A propellant-utilization system used for the first time on the Centaur, accurately controlled the fuel and oxidant consumption. The turnaround and retrothrust maneuver were performed without incident. Relatively high longitudinal modal excitations and lateral payload excitations were obtained at lift-off; these high perturbations are believed t o be related t o the launcher holddown arms. Nominal temperatures were recorded for both the external vehicle skin and the payload compartment; however, abnormally low temperatures were measured in the forward equipment area, which may have resulted from leakage of cold helium purge gas. All vehicle electrical systems performed satisfactorily; the only difficulty with the RF systems was obtained with the C-band transponder. of the vehicle instrumentation yielded valid data. The AC-6 vehicle was constructed with several new lightweight designs including the forward bulkhead, thrust barrel, interstage adapter and tank skin thickness reduction from 0.016 t o 0.014 inch. No deficiencies were observed in any of these new structural elements.

Source record↗
NASA NTRS1970

Payload impact of space shuttle and tug

The advantages offered by space shuttle and tug for space operations are summarized. Economical transportation to a space station and operations in orbit; frequent sorties, with flexible scheduling, for experiment missions; and an economical and flexible replacement for conventional launchers are discussed. These advantages include many potential benefits for payload design, construction, and use.

Newell, H. E.↗
NASA NTRS1970

Pyrotechnic hazards classification and evaluation program. Electrostatic vulnerability of the E8 and XM15/XM165 clusters, phase 1

A survey of the electrostatic vulnerability of explosive manufacturing plants and recommendations for reducing the vulnerability are discussed. During the course of the investigations, the XM15/XM165 and the E8 launcher were shown to be susceptible to electrostatic ignition. The pyrotechnic hazard of prime concern associated with electrostatics is that of the spark which can be generated. The heat, shock, and ionization produced by the spark can cause ignition of pyrotechnics. However, as a result of the initial ignition tests (XM15 fuse train), changes have been incorporated to make the fusing system relatively safe from premature electrostatic activation.

Source record↗
NASA NTRS1972

AS-511 facilities and environmental measurements program

A list is presented of the facilities and environmental measurements to be monitored in support of the Apollo/Saturn vehicle AS-511. The measurement identification number, description, transducer operating range, recorder type and drawings illustrating measurement location are included. The following launch complex 39 facilities will be used on this vehicle: launch complex 39 pad A, and launcher umbilical tower number 3.

Source record↗
NASA NTRS1972

Investigation of the use of microwave image line integrated circuits for use in radiometers and other microwave devices in X-band and above

Program results are described in which the use of a/high permittivity rectangular dielectric image waveguide has been investigated for use in microwave and millimeter wavelength circuits. Launchers from rectangular metal waveguide to image waveguide are described. Theoretical and experimental evaluations of the radiation from curved image waveguides are given. Measurements of attenuation due to conductor and dielectric losses, adhesives, and gaps between the dielectric waveguide and the image plane are included. Various passive components are described and evaluations given. Investigations of various techniques for fabrication of image waveguide circuits using ceramic waveguides are also presented. Program results support the evaluation of the image line approach as an advantageous method for realizing low loss integrated electronic circuits for X-band and above.

Knox, R. M.↗
NASA NTRS1971

Gasdynamics of explosions today.

A brief review is given of blast and detonation wave phenomena and some of their uses in war and peace. It is concluded that great strides have been made over the last three decades toward the physical understanding, the analytical-numerical solution, and the measurement of dynamic and thermodynamic quantities, also taking into consideration severe environments and extremely short durations. Questions of internal ballistics are discussed together with hypervelocity launchers and shock tubes, collapsing cylindrical drivers, spherical implosions, explosive weapons, dynamic response, and equation of state data.

Brode, H. L.↗
NASA NTRS1972

Prediction of hail damage to aircraft.

Description of a hailstone impact simulator, a valuable laboratory apparatus which can be used for such hailstone research as the testing of prospective structural designs or generating data to compare with theory. The simulator consists of a launcher and a velocity-measuring system. It has been successfully used to obtain deformation data on flat sheets and spherical caps of various sizes impacted by hailstones at typical flight velocities. A computer program is described which adequately predicts the damage to a simple structure when impacted by a hailstone.

Hayduk, R. J.↗
NASA NTRS1973

VICS-120 - A tube-vehicle system test facility.

Description of a large test facility for carrying out research in support of the aerodynamic and ventilation section of a handbook on subway design. The facility described is vertically oriented and has a test section with a nominal inside diameter of 2 in. and a length of 109 ft. It is capable of operating at Reynolds numbers up to full-scale (60,000,000) under open-end tube conditions. The facility is distinguished by a high degree of flexibility in configuration and operational limits. Details are given concerning the plenum assembly, the test section tubes, the scaffold, the instrumentation, the model launcher, the model arrestor, and the models themselves. A step-by-step account is given of the operation of the facility, and a brief sample of the type of data obtained from the facility is presented.

Marte, J. E.↗