Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Irradiation defect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Small scale tensile testing technique for measuring grain boundary strength of neutron-irradiated materials in focused ion beam systems

Irradiation induced defects on grain boundaries (GBs) can lead to GB strength degradation and cause intergranular cracking in structural materials, affecting the safe operation and service life of nuclear reactors. Establishing the quantitative relationship between the strength and character/microchemistry for individual GB in an effort of integrating experimental measurements and multiscale simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

NSUF RTE completion report for 23-4780: Microstructural Defect Induced Thermal Conductivity Reduction in Uranium Nitride and Thorium Nitride

Uranium nitride (UN) is known to have a higher thermal conductivity than traditional oxide fuels, which could lead to a more efficient energy transport and lower local temperature during its lifetime. But the thermal transport performance of UN in extreme environments has not been systematic studied. This study investigated the irradiation induced microstructural defects in UN and the impacts on thermal conductivity. The samples were produced by spark plasma sintering at University of Texas-San Antonio (UTSA), Los Alamos National Laboratory (LANL), and Idaho National Laboratory (INL). Thermal conductivity of UN before and after 2MeV proton irradiation were measured by using laser metrology at INL in a temperature range of 77-295K. Thermal conductivity measurements in this wide, cryogenic temperature range is critical to understand the phonon scattering mechanisms between the thermal energy carrier, phonons, and different types of irradiation-induced defects. In order to ensure the measurements were conducted in the same grains and minimize the impact of the local heterogeneities, the measurement locations were highlighted by fiducial marks using the focused ion beam (FIB) with grain orientation identified using the electron backscatter diffraction (EBSD) at the Center of Advanced Energy Studies (CAES). Irradiation experiment was conducted at the Ion Beam Laboratory at Texas A&M University (TAMU). A total of 6 samples were irradiated with different irradiation doses and temperatures. After irradiation, the microstructure was characterized by using Transmission Electron Microscope (TEM) at CAES (also in the FIB marks).

36 - MATERIALS SCIENCE↗
NASA NTRS1982

Defects and annealing studies in 1-Me electron irradiated (AlGa)As-GaAs solar cells

The deep-level defects and recombination mechanisms in the one-MeV electron irradiated (AlGa)As-GaAs solar cells under various irradiation and annealing conditions are discussed. Deep-level transient spectroscopy (DLTS) and capacitance-voltage (CV) techniques were used to determine the defect and recombination parameters such as energy levels and defect density, carrier capture cross sections and lifetimes for both electron and hole traps as well as hole diffusion lengths in these electron irradiated GaAs solar cells. GaAs solar cells used in this study were prepared by the infinite solution melt liquid phase epitaxial (LPE) technique at Hughes Research Lab., with (Al0.9Ga0.1)-As window layer, Be-diffused p-GaAs layer on Sn-doped n-GaAs or undoped n-GaAs active layer grown on n(+)-GaAs substrate. Mesa structure with area of 5.86x1000 sq cm was fabricated. Three different irradiation and annealing experiments were performed on these solar cells.

Li, S. S.↗
DOE OSTI2025

Tiny Bubbles: Combined HR(S)TEM and 4D-STEM Analysis of Sub-Nanometer He Bubbles in Au

Irradiation produces a distribution of defect sizes in materials, with the smallest defects often below one nanometer in size and approaching the scale of a single unit cell in metals. While high-resolution scanning transmission electron microscopy (STEM)-based imaging can directly image structures at this level, techniques such as four-dimensional STEM (4D-STEM) enable characterization of materials across large fields of view, capturing a more representative volume that can be valuable for quantifying defects, their distributions, and the associated strain fields. Here we present a combined HRSTEM and 4D-STEM approach to study the model system of He bubble implantation in an Au thin film. The present work is of general interest for the study of materials in extreme environments, as it demonstrates an effective way to characterize even the tiniest sub-nanometer sized He bubbles in addition to larger irradiation defects.

atomic-resolution STEM↗
NASA NTRS1964

Radiation Effects of Protons and Electrons in Silicon Diffused-Junction Detectors

Diffused n-on-p silicon particle detectors were irradiated with 1-Mev electrons, and with 31-Mev and 8.2-Mev protons. The detector capacitance was observed to increase with electron irradiation and to decrease with proton irradiation. A physical interpretation is given in terms of defect energy levels known to be introduced in silicon by irradiation. Defect ionization states are taken to be characteristic of the space-charge region, rather than of bulk silicon. The relation to other studies of damage in semiconductor particle detectors is pointed out, considering differences in the types of detector and irradiation used. The significance of these results is discussed for detector applications where the damage threshold is exceeded.

Scott, R. E.↗
DOE OSTI2021

Near-surface modification of defective KTaO 3 by ionizing ion irradiation

The synergistic effect of nuclear (S n ) and electronic (S e ) energy loss observed in some ABO 3 perovskites has attracted considerable attention due to the real possibility to modify various near-surface properties, such as the electronic and optical properties, by patterning ion tracks in the defective near-surface regions. In this study, we show that low-energy ion-induced disordering in conjunction with ionizing ion irradiation (18 MeV Si, 21 MeV Ni and 91.6 MeV Xe) is a promising approach for tailoring ion tracks in the near-surface of defective KTaO 3 . Experimental characterization and computer simulations reveal that the size of these latent ion tracks increases with S e and level of pre-existing damage. These results further reveal that the threshold S e value (S e th ) for track creation increases with decreasing pre-damage level. The values of S e th increase from 5.02 keV nm -1 , for a pre-existing fractional disorder of 0.53 in KTaO 3 , to 10.81 keV nm -1 for pristine KTaO 3 . Above these thresholds, amorphous latent tracks are produced due local melting and rapid quenching. Below a disorder fraction of 0.08 and S e ≤ 6.68 keV nm -1 , the synergistic effect is not active, and damage accumulation is suppressed due to a competing ionization-induced damage annealing process. These results indicate that, depending on S e and the amount of pre-existing damage, highly ionizing ions can either enhance or suppress damage accumulation in KTaO 3 , thus providing a pathway to tailoring defects states. Comprehending the conflicting roles of highly ionizing ions in defective ABO 3 oxides is vital for understanding and predictive modeling of ion-solid interactions in complex oxides, as well as for achieving control over ion track size in the near-surface of defective KTaO 3 .

36 MATERIALS SCIENCE↗
DOE OSTI2026

Defect formation and transmutation behaviors in irradiated tungsten under thermal-neutron shielded and mixed spectrum conditions

Here, this study investigates the microstructural evolution of pure tungsten irradiated under thermal-neutron shielded and mixed spectrum conditions in the High Flux Isotope Reactor (HFIR). Four samples were irradiated at temperatures from 570 °C to 1130 °C up to 0.73 dpa. Neutron spectrum significantly influenced the accumulation of transmutation products, with Re+Os content estimated at ∼0.3–0.6% under thermal-neutron shielded conditions and ∼5.2% under the mixed spectrum condition. Irradiation temperature strongly influences tungsten’s microstructure, with dislocation loops and fine voids forming at lower temperatures and only larger voids and Re/Os segregation observed at higher temperature. Under thermal-neutron shielded conditions, dislocation loops and voids were observed at 570 °C and 790 °C. At the highest irradiation temperature (1130 °C), dislocation loops were no longer observed, while larger but less dense voids remained. Re and Os segregation to void surfaces was evident at 790 °C and 1130 °C, though no precipitation was observed. In contrast, under the mixed-spectrum condition, both spherical and needle-like Re/Os-rich precipitates were observed, frequently accompanied by large voids. Dislocation loops were not observed, but loop-like contrast within the precipitates suggests they may have nucleated on pre-existing loops. Irradiation-induced hardening was assessed for the shielded samples at 570 °C and 790 °C. Dispersed barrier hardening (DBH) analysis, based on TEM-resolved defects, revealed that voids were the dominant contributors to hardening, consistent with literature results. A schematic model is proposed to describe defect and precipitate evolution in tungsten under fusion-relevant transmutation-to-dpa conditions.

Dislocation loops↗
DOE OSTI2025

Microstructure, stored energy, and stability of H/He-filled nanocavities in low temperature irradiated Inconel 718

The microstructure, trapped transmutation gases, stored energy, and mechanical behavior of samples from an irradiated Inconel 718 proton beam window were characterized using transmission electron microcopy, thermal desorption spectrometry (TDS), differential scanning calorimetry (DSC), and tensile testing. In the as-irradiated condition the microstructure contained a high number density of 1–3 nm gas-filled nanocavities. Emissions of trapped gases, H and He, during TDS correlated with peaks of the energy release curves from DSC examinations, which suggest these gases were likely stored in highly stable defect traps. The stored energy from radiation damage saturated at doses of a few dpa and did not increase with increasing radiation dose, but the amount of stored H and He increased with increasing dose. Effects of post-irradiation annealing were studied as well. After exposure to 700 °C, the nanocavities grew only slightly to 2–4 nm in diameter, but after exposure to 900 °C, the cavities grew to 10–20 nm in diameter and electron energy-loss spectroscopy showed these cavities contained a core of He surrounded by a shell of H. Further, this study demonstrated that the irradiation defect structures containing H and He were remarkably stable during irradiation and after exposure up to 700 °C. The effect of the irradiation temperature, defect mobility, and interaction of H, He, and irradiation defects on mechanical behavior provides insight into the processes responsible for the unusual recovery in ductility with increasing radiation dose observed in Inconel 718 after high energy proton and spallation neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effects cascade debris and helium bubbles on the strength of aged plutonium

The radioactive decay of aging Pu is dominated by α-decay. This persistent α-decay produces crystalline defects in the form of dislocation loops and helium bubbles that evolve with time. Comparable defects are produced in other metallic alloys when subject to neutron irradiation, and these defects are known to modify the plastic deformation of irradiated materials. Models have been developed for these irradiated materials and validated against experimental confirmations of yield strength and the concomitant microstructural evolution. In this paper, we deploy those previously developed models and apply their mechanics to plutonium aging.

Chemical elements↗
DOE OSTI2021

Microstructure-dependent rate theory model of defect segregation and phase stability in irradiated polycrystalline LiAlO 2

We report gamma lithium aluminate (LiAlO 2 ) is a breeder material for tritium and is one of key components in a tritium-producing burnable absorber rod (TPBAR). Dissolution and precipitation of second phases such as LiAl 5 O 8 and voids are observed in irradiated LiAlO 2 . Such microstructure changes cause the degradation of thermomechanical properties of LiAlO 2 and affect tritium retention and release kinetics, and hence, the TPBAR performance. In this work, a microstructure-dependent model of radiation-induced segregation (RIS) has been developed for investigating the accumulation of species and phase stability in polycrystalline LiAlO 2 structures under irradiation. Three sublattices (i.e. [Li, Al, V] I [O, V o ] II [Li i , Al i , O i , V i ] III ), and concentrations of six diffusive species (i.e. Li; vacancy of Li or Al at [Li, Al, V] I sublattice, O vacancy at [O, V o ] II sublattice, and Li, Al and O interstitials at [Li i , Al i , O i , V i ] III interstitial sublattices; are used to describe spatial and temporal distributions of defects and chemistry. Microstructure-dependent thermodynamic and kinetic properties including the generation, reaction, and chemical potentials of defects and defect mobility are taken into account in the model. The parametric studies demonstrated the capability of the developed RIS model to assess the effect of thermodynamic and kinetic properties of defects on the segregation and depletion of species in polycrystalline structures and to explain the phase stability observed in irradiated LiAlO 2 samples. The developed RIS model will be extended to study the precipitation of LiAl 5 O 8 and voids and tritium retention by integrating the phase-field method.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ta–Zr carbides: Synthesis advances via carbothermal reduction and defect evolution observed through transmission electron microscopy ion irradiation

The thermodynamic stability of six distinct compositions within the Zr—Ta—C ternary system is investigated in this study, marking the first report of their synthesis through carbothermic reduction in vacuum. A prolonged annealing process at 2200°C enabled high densification and phase equilibrium. Detailed phase identification and microstructural characterization through microscopy and X-ray diffraction techniques revealed clear compositional trends and stable phase formations. Two compositions ((Ta 0.2 Zr 0.8 )C 0.6 and (Ta 0.5 Zr 0.5 )C 1 ) were selected for ion irradiation experiments using 200 keV Kr + at 600°C—representing the first-ever irradiation study on the Zr—Ta—C system. The findings indicated defect accumulation and nanoscale cavity formation without any evidence of amorphization, highlighting the system's structural stability under irradiation. Together, the synthesis and irradiation results provide a basis for further investigation of the system and suggest its relevance for applications under extreme environments.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Effects of thermal annealing on the deep-level defects and I-V characteristics of 200 keV proton irradiated AlGaAs-GaAs solar cells

Detailed characterization of deep-level defects and analysis of dark I-V data in 200 keV proton irradiated AlGaAs-GaAs solar cells have been carried out for several proton fluences (5 x 10 to the 11th, 10 to the 12th, and 10 to the 13th P/sq cm), using DLTS, C-V, and I-V measurement techniques. To study the effect of low temperature thermal annealing on the deep-level defect properties, these irradiated samples were annealed in vacuum at 300 C for one hour. Comparison was then made on the measured defect parameters (i.e., defect energy levels and densities) and the dark I-V characteristics for both the annealed and unannealed samples.

Li, S. S.↗
NASA NTRS1994

Performance, Defect Behavior and Carrier Enhancement in Low Energy, Proton Irradiated p(+)nn(+) InP Solar Cells

InP p(+)nn(+) cells, processed by MOCVD, were irradiated by 0.2 MeV protons and their performance and defect behavior observed to a maximum fluence of 10(exp 13)/sq cm. Their radiation induced degradation, over this fluence range, was considerably+less than observed for similarly irradiated, diffused junction n p InP cells. Significant degradation occurred in both the cell's emitter and base regions the least degradation occurring in the depletion region. A significant increase in series resistance occurs at the highest fluenc.e. Two majority carrier defect levels, E7 and E10, are observed by DLTS with activation energies at (E(sub C) - 0.39)eV and (E(sub C) - 0.74)eV respectively. The relative concentration of these defects differs considerably from that observed after 1 MeV electron irradiation. An increased carrier concentration in the cell's n-region was observed at the highest proton fluence, the change in carrier concentration being insignificant at the lower fluences. In agreement with previous results, for 1 and 1.5 MeV electron irradiated InP p(+)n junctions, the defect level E10 is attributed to a complex between zinc, diffused into the n-region from the zinc doped emitter, and a radiation induced defect. The latter is assumed to be either a phosphorus vacancy or interstitial. The increased, or enhanced carrier concentration is attributed to this complex acting as a donor.

Weinberg, I.↗
NASA NTRS1984

Defect studies in one MeV electron irradiated GaAs and in Al/sub x Ga/sub l-x As P-N junction solar cells

Deep level transient spectroscopy reveals that the main electron traps for one-MeV electron irradiated GaAs cells are E9c)-0.31, E(c)-0.90 eV, and the main hole trap is due to the level. Electron trap density was found to vary from 3/tens-trillion ccm for 2/one quadrillion cm 3/3.7 quadrillion cm for 21 sextillion cm electron fluence for electron fluence; a similar result was also obtained for the hole trap density. As for the grown-in defects in the Al(x)Ga(1-x)As p-n junciton cells, only two electron traps with energies of E(c)-0.20 and E(c)-0.34 eV were observed in samples with x = 0.17, and none was found for x 0.05. Auger analysis on the Al(x)Ga(1-x) As window layer of the GaAs solar cell showed a large amount of oxygen and carbon contaminants near the surface of the AlGaAs epilayer. Thermal annealing experiment performed at 250 C for up to 100 min. showed a reduction in the density of both electron traps.

Li, S. S.↗
DOE OSTI2025

Intrinsic property of defective β-Ga 2 O 3 to self-heal under ionizing irradiation

Damage evolution and phase stability in defective β-Ga 2 O 3 and an irradiation-converted γ-Ga 2 O 3 layer have been studied under ionizing irradiation at 300 K. By exploring athermal nonequilibrium processes in β-Ga 2 O 3 , we succeed in identifying a self-healing mechanism that enables recovery pre-existing damage, characterized by a recovery cross-section of ~0.17 nm 2 . Remarkably, this study further demonstrates that the crystallinity of the irradiation-converted γ-Ga 2 O 3 layer improves under ionizing irradiation. More importantly, X-ray diffraction analysis reveals that the highly-strained 𝛾 -phase transforms into a highly-crystalline structure without film disintegration, contrasting to that reported for isochronal annealing at 1000 K. The inelastic thermal spike calculations provide insights into the important effects of energy transfer to electrons in reordering the local atomic arrangement of both defective β- Ga 2 O 3 and 𝛾-Ga 2 O 3 . This behavior suggests a pathway for low-temperature crystallization, offering a promising strategy for fabricating ultrahigh-speed non-volatile memory devices.

36 MATERIALS SCIENCE↗