Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ION CURRENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Tin asymmetric membranes for high capacity sodium ion battery anodes

Sodium-ion batteries have attracted tremendous research attention as promising candidates for next generation energy storage systems due to low-cost and high abundancy. Furthermore, comparing to current Li-ion battery technology, limitations on the anode side seriously hinder the cell performance since sodium does not easily intercalate into graphite materials. Here, tin nanoparticles embedded in various asymmetric membrane structures were developed to leverage the high capacity of tin (847 mA h g -1 based on Na 15 Sn 4 ) and accommodate the significant volume expansion for long cycle life. It was demonstrated 762 mA h g -1 reversible capacity at 50 mA g -1 and stable cycling performance over 100 cycles with 92.1% capacity retention at 100 mA g -1 can be achieved for the tin asymmetric membrane electrode synthesized using polysulfone and tin tert-butoxide precursor.

25 ENERGY STORAGE↗
DOE OSTI2021

Limiting Current in Nanostructured Block Copolymer Electrolytes

The next-generation electrolytes for lithium batteries must be able to conduct ions at sufficiently high current densities; yet this regime is rarely studied directly. The limiting current density of an electrolyte quantifies the highest possible rate of ion transport under an applied dc potential. Herein, we report on the limiting current density in twelve nanostructured polystyrene-block-poly(ethylene oxide) (PS-b-PEO, or SEO) copolymer electrolytes. We find that the limiting current at a given salt concentration increases systematically with increasing volume fraction of the PEO block (φ EO ). In contrast, the effective-medium theory, commonly used to analyze conductivity in block copolymer electrolytes, predicts that limiting current is independent of φ EO . To resolve this conundrum, the ionic conductivity, the mutual diffusion coefficient of the salt, and the steady-state current fraction of the block copolymer electrolytes were measured. These measurements enable predictions of limiting current with no adjustable parameters using the concentrated solution theory. We found quantitative agreement between experimentally measured limiting current densities and predictions based on the concentrated solution theory. This work sheds light on how to reliably measure and predict limiting current density in composite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2023

Ion beam profiling system and related methods

An ion beam profiling system include a beam profiling element, an ion sensitive element electrically isolated from the beam profiling element, an ion source configured to emit an ion beam at the beam profiling element and the ion sensitive element, and a current measuring device coupled to the ion sensitive element. The beam profiling element includes a plate of material having two parallel major surfaces, a first slit aperture extending through the plate of material and having a first longitudinal length extending in a direction parallel to the two parallel major surfaces, and a second slit aperture extending through the plate of material and having a second longitudinal length extending in a direction parallel to the two parallel major surfaces, wherein the first longitudinal length of the first slit aperture is perpendicular to the second longitudinal length of the second slit aperture.

Taylor, Chase N.↗
DOE OSTI2023

Investigation of oxygen ion mobility through Zr x Ta 2 O 2x+5 (ZTOx) and Hf 6 Ta 2 O 17 (HTO) at elevated temperatures

Thermal Protection Systems (TPS) allow for technology to withstand high heat, which is especially critical for aerospace applications. As technology advances, better TPS are required to keep up with more extreme operating temperatures. Ultra-High Temperature Ceramics (UHTCs) are of interest because of their high melting points above 3000°C, but they suffer from oxidation when exposed to the atmosphere. A standard remedy to prevent oxidation is the use an oxide coating to shield from oxygen in the atmosphere while still allowing high operating temperatures and thermal cycling. However, standard oxide coatings such as yttria stabilized zirconia (YSZ) have limited operating temperatures before they allow oxygen to diffuse into the substrate material. A recently proposed alternative material has the formula A 6 B 2 O 17 (A: Zr or Hf) (B: Ta or Nb). In this study, determination of the oxygen protection ability of Hf 6 Ta 2 O 17 (HTO), Zr 6 Ta 2 O 17 (ZTO6), and various Zr x Ta 2 O 2x+5 (ZTOx) was determined using Electrochemical Impedance Spectroscopy (EIS). Optimal synthesis and sintering conditions were determined for ZTO6 and several of its ZTO variations. Activation energy for oxygen mobility was also determined. The importance of ball milling was found to be crucial to achieve high sintering density with these ceramics. The sintering study revealed that the ideal temperature of the ZTO variations increased with increased Zr/Ta ratio in the formulation. It was determined that both HTO and the ZTO variations conduct oxygen ions less than current ceramic coatings such as YSZ, with HTO conducting the least, with results confirming the validity of both HTO and ZTO materials as candidates for TPS coatings based on their low oxygen ion conductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhanced prediction of Cs removal by CST from Hanford tank waste with K accountability

Abstract The treatment of Hanford tank waste is one of the most challenging environmental cleanup activities to date. To expedite the processing of liquid waste stored in underground tanks in Washington State it is necessary to remove the significant dose contributor, 137 Cs. Crystalline silicotitanate ion exchanger is currently used to remove 137 Cs from the aqueous phase of Hanford tank wastes in preparation for vitrification at the Waste Treatment and Immobilization Plant (WTP). Improving the understanding of potassium impacts on ion exchange behavior of Cs will help in the operation of a critical component of one of the most complex treatment processes in the world today. Optimization of this process can result in significant cost savings and less waste production. Toward this effort, a series of batch contact tests varied in potassium concentration were conducted to look at the impact of potassium concentration on Cs distribution. Experimental distribution ratios ( K d ) were compared to the distribution ratios predicted using the ZAM model. A significant underprediction of Cs capacity in the presence of potassium was seen with the existing model. A revision of the equilibrium constants was determined and provided a statistically better fit for determining the Cs K d values in tank waste matrices.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

High-power test results for a cylindrical-shell silicon carbide higher-order-mode damper

The next high-current Electron-Ion Collider (EIC) is a new accelerator to be built at Brookhaven National Laboratory in collaboration with Thomas Jefferson National Accelerator Facility. In the EIC Electron Storage Ring (ESR), there will be beam currents of up to 2.5 A, which will excite massive higher-order-mode (HOM) power in the 17 single-cell 591 MHz superconducting radio-frequency (SRF) cavities. Damping the HOM power in the ESR SRF cavities is a challenge. A room temperature cylindrical shell shape silicon carbide (SiC) beamline HOM absorber (BLA) was chosen as the baseline design, due to its broadband and high-power capability, and previous demonstrations at other accelerator facilities, albeit at much lower power. Because the EIC BLA HOM power dissipation is significantly greater than the previous applications, it is imperative to carry out high-power testing to determine the maximum device performance levels achievable for thermal transport, rf breakdown, and mechanical stress, prior to finalizing the design. A SiC HOM absorber with a state-of-the-art geometry size was prototyped to verify the shrink-fit technique, test outgassing rate, and high-power handling capability. This paper presents the HOM damper’s prototyping and test results. Published by the American Physical Society 2024

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Protective coatings with nanoscale multilayer architecture: current state and main trends

Binary systems (layers) and multicomponent layers with bilayer thicknesses varying from microns to a few nanometers are considered. A strong dependence of the microstructure formation on the deposition conditions (the magnitude of the bias potential, the flow of inert and reactive gases, the ion beam power (current density) supplied to the target) is found. General regularities in the change in the functional properties and structural state of the coatings are formulated. The conditions for the formation of a columnar structure and growth texture are noted; various mechanisms and their interpretation are proposed. Finally, the relationship among the size of nanograins, diffusion at the interphase boundary, and effects determining the physico-mechanical, tribological characteristics, as well as resistance to corrosion and oxidation, is shown.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Isostatic pressing of multilayer pouch cells and its implications for battery manufacturing

Here, we report a comprehensive investigation into the impact of isostatic pressure (ISP) processing on multilayer pouch cells. The study compares baseline electrodes fabricated using conventional manufacturing processes with isostatically pressed counterparts under varying conditions. Extensive characterization is carried out to assess the differences between baseline cells and those that underwent the isostatic pressing process. The electrochemical performance of the isostatically pressed cathodes was evaluated through impedance spectroscopy and galvanostatic charge-discharge tests. The results indicated that ISP led to notable improvements in porosity, adhesion, and rate performance compared to the baseline cathodes. This work elucidates the microstructural changes induced by ISP in lithium-ion battery cathodes and highlights the technology’s promise for advancing battery manufacturing. The findings contribute to a better understanding of how ISP can be effectively integrated into cell assembly, fostering the development of more efficient and scalable battery manufacturing techniques for current Li-ion and solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Non-equilibrium insertion of lithium ions into graphite

Graphite has been regarded as the most important anode material for currently used lithium-ion batteries due to its two-dimensional (2D) nature hosting ionic intercalations. However, the kinetic insertion of Li ions is still not well known microscopically. In this work, we investigate the real-time intercalation process of Li ions using in situ transmission electron microscopy. We observe the lithium insertion process at the atomic scale, in which the graphite layers undergo expansion, forming wrinkles and finally inhomogeneous cracks as the Li ions accumulate, different from the proposed models. Leveraging on theoretical simulations, Li-ion migration driven by an external electrical field is suggested to be induced into the irreversible wrinkled structures. This non-equilibrium behavior that occur in lithium-ion batteries can be more pronounced at a high charging rate, which will practically degrade the capacity of graphite. Furthermore, this work unveils the reaction scenario of the non-equilibrium Li-ion insertion, which benefits the understanding of the performance of graphite-based energy-storage devices.

25 ENERGY STORAGE↗
DOE OSTI2022

Fast wave interferometer for ion density measurement on DIII-D

=A fast wave interferometer (FWI), which can measure ion mass density, has been developed on DIII-D for its use on future fusion reactors, as well as for the study of ion behavior in current plasma devices. The frequency of the fast waves used for the FWI is around 60 MHz, and require antennas and coaxial cables or waveguides, which, unlike traditional mirror-based optical interferometers, are less susceptible to neutron/gamma-ray radiation and are relatively immune to impurity deposition and erosion as well as alignment issues. The bulk ion density evaluated using FWI show good agreement with that derived from CO 2 interferometry within about 15%. When the ion mass density measurement by FWI is combined with an electron density measurement from CO 2 interferometry, Z eff measurements are also enabled and are in agreement with those from visible Bremsstrahlung measurements. Additionally, large-bandwidth FWI measurements clearly resolve 10–100 kHz coherent modes and demonstrate its potential as a core fluctuation diagnostic, sensitive to both magnetic and ion density perturbations.

Instruments & Instrumentation↗
DOE OSTI2025

Development of Li–S Battery Cells with High Energy Density and Long Cycling Life

Lithium–sulfur (Li–S) batteries are considered one of the most promising next-generation energy storage technologies for electric vehicles, owing to their high energy density (up to three times greater than current lithium-ion batteries) and the low cost of sulfur (approximately 100 times cheaper than conventional cobalt oxide). However, several challenges hinder their commercial viability, including the electronically and ionically insulating nature of sulfur, polysulfide dissolution, and lithium dendrite growth. These issues significantly limit battery energy density and cycle life and must be addressed to enable successful commercialization. Current strategies involving porous carbon structures, additives, and electrocatalyst engineering have not fully resolved the polysulfide dissolution problem. While polysulfide-free cathode materials offer a promising solution, they often suffer from low sulfur content, leading to reduced discharge capacity and sluggish reaction kinetics. To overcome these limitations, we have developed novel soluble-polysulfide-free sulfur cathode active materials with a high sulfur content (>50 wt%). By integrating these cathodes with functional binders, optimized electrolyte formulations, and refined electrode fabrication techniques, we demonstrate Li–S batteries with both high energy density and long cycle life. This advancement brings the realization of low-cost, high-energy Li–S batteries significantly closer to practical application.

25 ENERGY STORAGE↗
DOE OSTI2025

Comparison of Ion and Neutron Irradiations to 3 dpa at 500C in Ferritic-Martensitic Alloys

The growing global demand for energy will increasingly call upon advanced nuclear fission reactors to supply safe and reliable electricity. The structural and fuel cladding components of these reactors will be subject to extreme conditions of irradiation damage up to several hundred displacements per atom (dpa) at temperatures as high as 700°C. Ferritic-martensitic (F-M) steels are leading candidates for these challenging conditions due to their strength and dimensional stability under irradiation. In order to accelerate the process for evaluating F-M alloys, charged particles are increasingly being used to emulate neutron irradiations. Charged particle irradiations allow the possibility of conducting irradiation experiments within a shorter time period (i.e. at a rate up to 4 orders of magnitude faster) and with minimal radioactivation of the material, enabling lower cost and faster turnaround of post irradiation examination and analysis. However, the irradiation dose rate, damage cascade morphologies, and irradiation damage depth profiles all differ widely between protons, heavier ions, and neutrons. Currently, there is limited understanding of the significance of these physical differences and how they manifest in the irradiated microstructure and mechanical properties of F-M steels. The objective of this study is to evaluate charged particles as a surrogate for neutron irradiations in F-M alloys by assessing common irradiation conditions using Fe++ ions, protons, and neutrons. Keeping the temperature and dose consistent enables isolation of the effects of each irradiating particle and their respective dose rates and cascade morphologies.

Swenson, M.J.↗
DOE OSTI2023

Machine learning-based jet and event classification at the Electron-Ion Collider with applications to hadron structure and spin physics

We explore machine learning-based jet and event identification at the future Electron-Ion Collider (EIC). We study the effectiveness of machine learning-based classifiers at relatively low EIC energies, focusing on (i) identifying the flavor of the jet and (ii) identifying the underlying hard process of the event. We propose applications of our machine learning-based jet identification in the key research areas at the future EIC and current Relativistic Heavy Ion Collider program, including enhancing constraints on (transverse momentum dependent) parton distribution functions, improving experimental access to transverse spin asymmetries, studying photon structure, and quantifying the modification of hadrons and jets in the cold nuclear matter environment in electron-nucleus collisions. We establish first benchmarks and contrast the estimated performance of flavor tagging at the EIC with that at the Large Hadron Collider. We perform studies relevant to aspects of detector design including particle identification, charge information, and minimum transverse momentum capabilities. Additionally, we study the impact of using full event information instead of using only information associated with the identified jet. These methods can be deployed either on suitably accurate Monte Carlo event generators, or, for several applications, directly on experimental data. We provide an outlook for ultimately connecting these machine learning-based methods with first principles calculations in quantum chromodynamics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Microstructural and nanomechanical studies of PVD Cr coatings on SiC for LWR fuel cladding applications

The microstructure and nanomechanical properties of pure Cr coatings deposited on SiC with various physical vapor deposition (PVD) methods have been investigated for the mitigation of hydrothermal corrosion of SiC-SiC f (SiC fiber-reinforced SiC matrix) composite fuel cladding in light water reactors (LWR). Cr coatings (4–7 μm thick) were deposited on unbiased SiC substrates using six variants of magnetron sputtering processes: (i) standard (S-DCMS), (ii) pulsed (P-DCMS), (iii) ion-assisted (I-DCMS), and (iv) pulsed ion-assisted direct current magnetron sputtering (PI-DCMS), (v) high-power impulse magnetron sputtering (HiPIMS), and (vi) bipolar HiPIMS (B-HiPIMS). Microstructural characterization and nanoindentation testing were used to evaluate effects of deposition technique on coating microstructure and nanomechanical properties. The application of positive reverse pulses to the sputter target induced coarsening of the columnar grain structure, while ion bombardment of substrates during deposition promoted densification of the coating microstructure. Both effects are exemplified in B-HiPIMS deposition, resulting in a high-density microstructure with compressive residual stress. Material pile-up around nano-indents and plastic work during nanoindentation were analyzed to understand deformation behavior of the coatings. Finally, the results suggest the B-HiPIMS process to be among the promising methods for the deposition of Cr coatings on SiC-SiC f for LWR cladding application.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Developing Materials for High-Energy-Density Solid State Li-S Batteries

Solid-state lithium-sulfur batteries are considered to be the next-generation power source for vehicle applications due to their high energy density (up to 3 times more than current Li-ion) and low cost of sulfur (100 times less than conventional cobalt oxide). However, issues with solid-state electrolyte stability, conduction pathways in the sulfur cathode, and the interface between solid-state electrolyte and sulfur cathode must be solved in order to allow commercialization. This project demonstrates the creation of new, advanced materials which overcome these inherent issues. Current approaches based on polymer or liquid electrolyte with additives have been able to improve stability at the cost of efficiency. In contrast, by creating new hybrid materials it is possible to achieve both stability and efficiency. We developed a novel sulfide-based solid electrolyte, a sulfur-carbon composite cathode, and explored various additives to stabilize the interface of solid electrolyte and cathode. After the desired properties were achieved, these materials were integrated into a high-performance solid-state battery, bringing low-cost high-energy solid-state lithium-sulfur batteries one step closer to reality.

25 ENERGY STORAGE↗
DOE OSTI2020

Uncovering the Relationship between Diameter and Height of Electrodeposited Lithium Protrusions in a Rigid Electrolyte

A promising approach for enabling rechargeable batteries with significantly higher energy densities than current lithium-ion batteries is by deploying lithium-metal anodes. However, the growth of lithium protrusions during charging presents significant challenges. Since these protrusions are often branched and filamentous in conventional liquid electrolytes, this problem is referred to in the literature as the “dendrite problem”. While solid electrolytes have the potential to solve this problem, protrusions grow in all electrolytes when the current density exceeds a critical value. Fundamentally understanding the formation is necessary to develop a rational approach for increasing the critical current density, but it is challenging due to the complex interplay between electrochemical and material properties. The diameters and heights of protrusions on lithium-metal anodes stabilized by a rigid block copolymer electrolyte were measured in situ by synchrotron hard X-ray microtomography. The diameter of the shorting protrusions increased linearly with increasing electrolyte thickness. Further, a universal linear relationship between protrusion height and diameter of both shorting and non-shorting protrusions was observed. A model based on the concentrated solution theory was used to establish the electrochemical and mechanical sources for our observations. Here, the computational analysis indicates that elastic and plastic deformation of both the lithium metal and the polymer are important to describe protrusion growth. Both stress-induced current density effects due to the deformation of the electrolyte near the protrusion and plastic deformation of lithium metal combine to give the counterintuitive result: the fastest-growing protrusions have the largest diameter.

25 ENERGY STORAGE↗