Results for “Hysteresis model” — Page 11

NASA NTRS1976

Flight test of a stall sensor and evaluation of its application to an aircraft stall deterrent system using the NASA LRC general aviation simulator

A series of flight maneuvers were developed to cover the range of flight conditions and to define the repeatability and hysteresis of the sensors. Initial flights were made with two sensors at the + or - 68 percent span and 60 percent and 70 percent chord stations. The primary effort in simulation program development was to modify the LRC General Aviation Simulator (GAS) Fortran programs to allow execution on the MSU UNIVAC 1106. A simple model of the sensor-servo stall deterrent system was developed. A one degree of freedom model of pitch dynamics of the airplane and stall deterrent system was developed to make initial estimates of the control system gains. A position error plus rate damping control algorithm was found to have acceptable characteristics.

Bennett, G.↗

NASA NTRS1982

Time lags in solar modulation

Von Rosenvinge and Paizis (1981) have discussed the amplitude variations of low energy cosmic rays, taking into account intensity-time variations which occurred starting in late 1973 and continued into mid-1975. The present investigation is concerned with the occurrence of so-called hysteresis effects during the considered period. A graph is presented which shows a comparison of the time-intensity plots for 35.3-82 MeV protons (340 MV) and the Deep River neutron monitor. A time lag can be observed between the neutron monitor intensity and the 35.3-82 MeV proton intensity. The same data is replotted to show a hysteresis loop. A plot for 35.1-82 MeV/n helium is also provided. It is found that all measured values of the time lag for protons and helium are consistent with those reported by Klecker et al. (1980). It is pointed out that the time lag for the anomalous helium is not consistent with the model of O'Gallagher (1975).

Paizis, C.↗

NASA NTRS1994

Nonlinear dynamics of drops and bubbles and chaotic phenomena

Nonlinear phenomena associated with the dynamics of free drops and bubbles are investigated analytically, numerically and experimentally. Although newly developed levitation and measurement techniques have been implemented, the full experimental validation of theoretical predictions has been hindered by interfering artifacts associated with levitation in the Earth gravitational field. The low gravity environment of orbital space flight has been shown to provide a more quiescent environment which can be utilized to better match the idealized theoretical conditions. The research effort described in this paper is a closely coupled collaboration between predictive and guiding theoretical activities and a unique experimental program involving the ultrasonic and electrostatic levitation of single droplets and bubbles. The goal is to develop and to validate methods based on nonlinear dynamics for the understanding of the large amplitude oscillatory response of single drops and bubbles to both isotropic and asymmetric pressure stimuli. The first specific area on interest has been the resonant coupling between volume and shape oscillatory modes isolated gas or vapor bubbles in a liquid host. The result of multiple time-scale asymptotic treatment, combined with domain perturbation and bifurcation methods, has been the prediction of resonant and near-resonant coupling between volume and shape modes leading to stable as well as chaotic oscillations. Experimental investigations of the large amplitude shape oscillation modes of centimeter-size single bubbles trapped in water at 1 G and under reduced hydrostatic pressure, have suggested the possibility of a low gravity experiment to study the direct coupling between these low frequency shape modes and the volume pulsation, sound-radiating mode. The second subject of interest has involved numerical modeling, using the boundary integral method, of the large amplitude shape oscillations of charged and uncharged drops in the presence of a static or time-varying electric field. Theoretically predicted non linearity in the resonant frequency of the fundamental quadrupole mode has been verified by the accompanying experimental studies. Additional phenomena such as hysteresis in the frequency response of ultrasoncially levitated droplets in the presence of a time varying electric field, and mode coupling in the oscillations of ultrasonically modulated droplets, have also been uncovered. One of the results of this ground-based research has been the identification and characterization of phenomena strictly associated with the influence of the gravitational field. This has also allowed us to identify the specific requirements for potential microgravity investigations yielding new information not obtainable on Earth.

Trinh, Eugene H.↗

NASA NTRS1984

On the dynamics of stratocumulus formation and dissipation

Results obtained with a mixed layer model are used to study the dynamics of stratocumulus formation and dissipation in subtropical marine stratocumulus cloud regimes. The model used allows entrainment to be driven by shear as well as buoyancy, and includes a very crude parameterization of the partial blackness of thin cloud layers. Model results show that for some values of the large-scale divergence there are three equilibrium mixed layer structures, two of which are stable. One of the stable equilibria is cloudy, deep, and buoyancy-driven, while the other is clear, shallow, and shear-driven. It is found that as a result of hysteresis effects a transient increase in the large-scale divergence can produce a long-lasting break in the clouds.

Randall, D. A.↗

NASA NTRS1985

An update of the total-strain version of SRP

An updated procedure for characterizing an alloy and predicting cyclic life by using the total strain range version of strainrange partitioning (TS-SRP) has been developed. The principal feature of this update is a new procedure for determining the intercept of time dependent elastic strain range versus cyclic life lines. The procedure is based on an established relation between failure and the cyclic stress-strain response of an alloy. The stress-strain response is characterized by empirical equations presented in this report. These equations were determined with the aid of a cyclic constitutive model. The procedures presented herein reduce the testing required to characterize an alloy. Failure testing is done only in the high strain, low life regime; cyclic stress-strain response is determined from tests conducted in both the high and low strain regimes. These tests are carried out to stability of the stress-strain hysteresis loop but not to failure. Thus both the time and costs required to characterize an alloy are greatly reduced. This approach was evaluated and verified for two nickel base superalloys, AF2-1DA and Inconel 718.

Saltsman, J. F.↗

NASA NTRS1986

Identification of nonlinear system parameters in joints using the force-state mapping technique

A procedure is presented for identifying the potentially strong nonlinear properties of structural members, such as joints, by expressing the force transmitted by the member as a function of its mechanical state. By explicitly including position and rate dependent effects, the surface of transmitted force versus state, the force-state map, has distinct, unique, superposable features for common structural nonlinearities, even those which appear to indicate hysteresis on a force-stroke presentation. An analysis is performed on the influence of true memory effects, transient response, and uncertainty in the measurements and system mass on the precision of the procedure. The successful identification of simulated data verifies the accuracy of the identification algorithm. Tests are then conducted on three actual joint models, with incomplete state measurements typical of an actual testing environment. The ability of the procedure to estimate the complete state vector and to analyze and reconstruct the measured nonlinear characteristics is demonstrated.

Crawley, E. F.↗

NASA NTRS1988

An update of the total-strain version of SRP

An updated procedure for characterizing an alloy and predicting cyclic life by using the total strain range version of strainrange partitioning (TS-SRP) has been developed. The principal feature of this update is a new procedure for determining the intercept of time dependent elastic strain range versus cyclic life lines. The procedure is based on an established relation between failure and the cyclic stress-strain response of an alloy. The stress-strain response is characterized by empirical equations presented in this report. These equations were determined with the aid of a cyclic constitutive model. The procedures presented herein reduce the testing required to characterize an alloy. Failure testing is done only in the high strain, low life regime; cyclic stress-strain response is determined from tests conducted in both the high and low strain regimes. These tests are carried out to stability of the stress-strain hysteresis loop but not to failure. Thus both the time and costs required to characterize an alloy are greatly reduced. This approach was evaluated and verified for two nickel base superalloys, AF2-1DA and Inconel 718.

Saltsman, James F.↗

NASA NTRS1995

A kinematically driven anisotropic viscoelastic constitutive model applied to tires

Aircraft tires are composite structures manufactured with viscoelastic materials such as carbon black filled rubber and nylon cords. When loaded they experience large deflections and moderately large strains. Detailed structural models of tires require the use of either nonlinear shell or nonlinear three dimensional solid finite elements. Computational predictions of the dynamic response of tires must consider the composite viscoelastic material behavior in a realistic fashion. We describe a modification to a nonlinear anisotropic shell finite element so it can be used to model viscoelastic stresses during general deformations. The model is developed by introducing internal variables of the type used to model elastic strain energy. The internal variables are strains, curvatures, and transverse shear angles which are in a one-to-one correspondence with the generalized coordinates used to model the elastic strain energy for nonlinear response. A difference-relaxation equation is used to relate changes in the observable strain field to changes in the internal strain field. The internal stress state is introduced into the equilibrium equations by converting it to nodal loads associated with the element's displacement degrees of freedom. In this form the tangent matrix in the Newton-Raphson solution algorithm is not modified from its form for the nonlinear statics problem. Only the gradient vector is modified and the modification is not computationally costly. The existing finite element model for the Space Shuttle nose gear tire is used to provide examples of the algorithm. In the first example, the tire's rim is displaced at a constant rate up to a fixed value. In the second example, the tire's rim is enforced to follow a saw tooth load and unload curve to generate hysteresis loops.

Johnson, Arthur R.↗

NASA NTRS1993

Loss of equilibrium and reconnection in tearing of two-dimensional equilibria

Two-dimensional tearinglike behavior is studied in reduced resistive magnetohydrodynamics (MHD) with flux conserving boundary conditions on a rectangular box. The tearinglike perturbations do not destroy the symmetries of the initial state, either discrete or continuous. In such cases, in which the perturbation does not break a symmetry of the equilibrium, linear instability is typically not directly observed. However, there can be a loss of equilibrium associated with the existence of a tearing unstable state. These ideas are illustrated with three examples: a very elongated tokamak, a tokamak with pinching coils to elongate its flux surfaces, and a model for the magnetotail or for solar arcades. The loss of equilibrium is demonstrated by means of a nonlinear energy functional. The importance of the fact that the dynamics shows a loss of equilibrium is that a large amount of free energy can be released, in the form of reconnection, and that there is a possibility of hysteresis.

Finn, John M.↗

NASA NTRS1993

Characterization facility for magneto-optic media and systems

Objectives of this research are: (1) to measure the hysteresis loop, Kerr rotation angle, anisotropy energy profile, Hall voltage, and magnetoresistance of thin-film magneto-optic media using our loop-tracer; (2) measure the wavelength-dependence of the Kerr rotation angle, Theta(sub k), and ellipticity, epsilon(sub k), for thin-film media using our magneto-optic Kerr spectrometer (MOKS); (3) measure the dielectric tensor of thin-film and multilayer samples using our variable-angle magneto-optic ellipsometer (VAMOE); (4) measure the hysteresis loop, coercivity, remanent magnetization, saturation magnetization, and anisotropy energy constant for thin film magnetic media using vibrating sample magnetometry; (5) observe small magnetic domains and investigate their interaction with defects using magnetic force microscopy; (6) perform static read/write/erase experiments on thin-film magneto-optic media using our static test station; (7) integrate the existing models of magnetization, magneto-optic effects, coercivity, and anisotropy in an interactive and user-friendly environment, and analyze the characterization data obtained in the various experiments, using this modeling package; (8) measure focusing- and tracking-error signals on a static testbed, determine the 'feedthrough' for various focusing schemes, investigate the effects of polarization and birefringence, and compare the results with diffraction-based calculations; and (9) measure the birefringence of optical disk substrates using two variable angle ellipsometers.

Mansuripur, M.↗

NASA NTRS1975

Implications of time variations for the origin of low energy cosmic ray nitrogen and oxygen nuclei

Time variations have been observed in the quiet time intensities of 5-27 MeV/nuc nitrogen and oxygen and 13-25 MeV/nuc helium nuclei measured by spectrometers aboard IMPs 7 and 8. There is no significant correlation of the O variations with variations in the low intensity fluxes of 1-2 MeV solar protons, but the O intensity is well correlated with the modulation of galactic cosmic rays. These observations indicate that the enhanced low energy N and O fluxes are not of solar origin, and suggest that the acceleration mechanism required by the model of Fisk et al. (1974) must be located far enough from the sun that the singly charged ions, once accelerated, undergo considerable modulation in penetrating to 1 AU. Comparison of the time variations of He and O fluxes may yield information on the charge state of these nuclei, since these variations are strongly correlated and exhibit similar hysteresis effects when compared with the neutron monitor.

Mewaldt, R. A.↗

NASA NTRS2014

Optic Nerve Sheath Mechanics and Permeability in VIIP Syndrome

Long-duration space flight carries the risk of developing Visual Impairment and Intracranial Pressure (VIIP) syndrome, a spectrum of ophthalmic changes including posterior globe flattening, choroidal folds, distension of the optic nerve sheath (ONS), optic nerve kinking and potentially permanent degradation of visual function. The slow onset of VIIP, its chronic nature, and certain clinical features strongly suggest that biomechanical factors acting on the ONS play a role in VIIP. Here we measure several relevant ONS properties needed to model VIIP biomechanics. The ONS (meninges) of fresh porcine eyes (n7) was reflected, the nerve proper was truncated near the sclera, and the meninges were repositioned to create a hollow cylinder of meningeal connective tissue attached to the posterior sclera. The distal end was cannulated, sealed, and pressure clamped (mimicking cerebrospinal fluid [CSF] pressure), while the eye was also cannulated for independent control of intraocular pressure (IOP). The meninges were inflated (CSF pressure cycling 7-50 mmHg) while ONS outer diameter was imaged. In another set of experiments (n4), fluid permeation rate across the meninges was recorded by observing the drainage of an elevated fluid reservoir (30 mmHg) connected to the meninges. The ONS showed behavior typical of soft tissues: viscoelasticity, with hysteresis in early preconditioning cycles and repeatable behavior after 4 cycles, and nonlinear stiffening, particularly at CSF pressures 15 mmHg (Figure). Tangent moduli measured from the loading curve were 372 101, 1199 358, and 2050 379 kPa (mean SEM) at CSF pressures of 7, 15 and 30 mmHg, respectively. Flow rate measurements through the intact meninges at 30mmHg gave a permeability of 1.34 0.46 lmincm2mmHg (mean SEM). The ONS is a tough, strain-stiffening connective tissue that is surprisingly permeable. The latter observation suggests that there could be significant CSF drainage through the ONS into the orbit, likely important for CSF transport in the optic nerve. These experimental measurements, extended to human eyes, are informing computational models of the pathophysiology and biomechanics of the ONS in VIIP syndrome.

biomechanics↗

NASA NTRS2014

Biomechanics of the Optic Nerve Sheath in VIIP Syndrome

Long-duration space flight carries the risk of developing Visual Impairment and Intracranial Pressure (VIIP) syndrome, a spectrum of ophthalmic changes including posterior globe flattening, choroidal folds, distension of the optic nerve sheath (ONS), optic nerve kinking and potentially permanent degradation of visual function. The slow onset of VIIP, its chronic nature, and certain clinical features strongly suggest that biomechanical factors acting on the ONS play a role in VIIP. Here we measure several relevant ONS properties needed to model VIIP biomechanics. The ONS (meninges) of fresh porcine eyes (n7) was reflected, the nerve proper was truncated near the sclera, and the meninges were repositioned to create a hollow cylinder of meningeal connective tissue attached to the posterior sclera. The distal end was cannulated, sealed, and pressure clamped (mimicking cerebrospinal fluid [CSF] pressure), while the eye was also cannulated for independent control of intraocular pressure (IOP). The meninges were inflated (CSF pressure cycling 7-50 mmHg) while ONS outer diameter was imaged. In another set of experiments (n4), fluid permeation rate across the meninges was recorded by observing the drainage of an elevated fluid reservoir (30 mmHg) connected to the meninges. The ONS showed behavior typical of soft tissues: viscoelasticity, with hysteresis in early preconditioning cycles and repeatable behavior after 4 cycles, and nonlinear stiffening, particularly at CSF pressures 15 mmHg (Figure). Tangent moduli measured from the loading curve were 372 101, 1199 358, and 2050 379 kPa (mean SEM) at CSF pressures of 7, 15 and 30 mmHg, respectively. Flow rate measurements through the intact meninges at 30mmHg gave a permeability of 1.34 0.46 lmincm2mmHg (mean SEM). The ONS is a tough, strain-stiffening connective tissue that is surprisingly permeable. The latter observation suggests that there could be significant CSF drainage through the ONS into the orbit, likely important for CSF transport in the optic nerve. These experimental measurements, extended to human eyes, are informing computational models of the pathophysiology and biomechanics of the ONS in VIIP syndrome.

fluid shifts↗

NASA NTRSDate not supplied

Composition-property correlations in NiTi-based shape memory alloys from the first principles

Development of shape memory alloys (SMA) has been traditionally accomplished by means of extensive empirical efforts, with a very limited support from phenomenological models and related tools. We present a theoretical framework based on the Hamiltonian formalism, which connects important thermodynamic properties directly to the relative energies (the eigenvalues of the Hamiltonian), computed from the first principles using density functional theory. The estimates based on this formalism allow to establish correlations between composition and physical properties, such as relative energies, phase transition temperatures, hysteresis, thermal expansion, and other thermodynamic information. Importantly, estimates and correlations not only provide a fast answer, but also elucidate underpinning of thermodynamic features in terms of the electronic structure. Using this framework, we consider phase transformations and correlations between the selected properties and composition in the NiTi-based ternary and multicomponent shape memory alloys. Our theoretical guidance facilitates design and development of future alloys.

shape memory alloys↗

NASA NTRS1986

Effect of an upstream wake on a pusher propeller

An analytical/computational study has been conducted to predict the effect of an upstream wake on an operating propeller. The upstream wing/pylon was modeled by a constant chord wing of NACA 0012 sections and was placed at a variable distance (0.1 - 0.3 chord) upstream of a scaled model propeller (SR-2). The wake model was a similarity formulation. The periodic behavior ofthe flow during the passage through the wake was formulated in terms of time-dependent variation of each blade section's angle of attack. It was found that the final expressions for the unsteady pressure distribution on each blade section are periodic and that the unsteady circulation and lift coefficieents exhibit a hysteresis loop.

Takallu, M. A.↗

NASA NTRS1989

Detection of potential space station control/structure interaction with CO-ST-IN

The NASA Lewis Research Center is concerned with the potential of interaction between space station controllers and the solar PV array structures. The models required to handle this problem are very large, and automated methods were developed for the transfer of data between structural dynamic and control system analysis software. These methods emphasize the need to achieve accurate coupled analysis results while using as small a model as possible. Specific tools which help the analyst in this regard include modal order techniques, the use of mode acceleration to calculate internal loads and stresses and the transfer of Craig-Bampton components to reduce problems associated with modal sufficiency. These techniques were applied to a space station model with 366 modes below 1 Hz. Attitude control, and alpha and beta joint control were simulated. The inclusion of alpha and beta joint controllers is important when examining overall space station dynamics. An initial choice of control parameters does indicate a potential for control/structure interaction during reboost. As expected this is exacerbated by increasing the rate gain and decreasing the hysteresis of the reaction control system (RCS) in order to improve rigid body performance.

Carney, Kelly↗

NASA NTRS1987

Experimental evaluation of small-scale erectable truss hardware

To aid in the prediction of the dynamic behavior of the space station, a one-tenth scale dynamic test model is to be constructed of commercially available, small scale truss hardware. Tests have been performed to determine the axial stiffness characteristics and failure loads of the truss joint. A parametric study has shown that the stiffness of the joint increases as the attachment bolt torque value is increased. Furthermore, at torque values equal to or higher than 250 in-lbs, hysteresis in the load-deflection curve is essentially eliminated. Also, the joint stiffness remained relatively constant between specimens. The effective stiffness of a joint subassembly tested is 76 percent that of the strut. Tensile and compressive failure occurred in the region of the bonded plug, with lower failure loads corresponding to compressive loadings.

Mcgowan, David M.↗

NASA NTRS2018

Observations on Dynamic Qualification Testing of a Component with Nonlinear Deadband Interfaces

Typical flight hardware dynamic qualification tests exhibit nearly linear structural response when exposed to acceleration inputs from low to full qualification levels. Even in these “linear” cases, there is typically a trend of increasing damping with test levels. The nonlinear mechanism behind this increase in energy dissipation well understood – typically stick/slip hysteresis at joint connections. This paper is concerned with a different type of nonlinearity: deadbands at structural interfaces. Deadband nonlinearities can have a significant influence on structural response and modal/spectral characteristics which can present difficulties in test, analysis, and structural certification. This subject nonlinear behaviour is observed during flight qualification testing of the AQUARIUS instrument and discussed here. Simple physical reasoning and analytical model is utilized to explain the behaviour which is consistent with the test findings.

Majed, Arya↗