Results for “Hypersonic Cone” — Page 11

NASA NTRS1976

Turbulent viscous-shock-layer solutions with strong vorticity interaction

Numerical solutions of the viscous-shock-layer equations governing laminar and turbulent flows of a perfect gas and radiating and nonradiating mixtures of perfect gases in chemical equilibrium are presented for hypersonic flow over spherically blunted cones and hyperboloids. The results are compared with boundary-layer and inviscid flow-field solutions. The agreement with the inviscid flow field data is satisfactory. The agreement with boundary-layer solutions is good except in regions of strong vorticity interaction. In these flow regions, the viscous-shock-layer solutions appear to be more satisfactory than the boundary-layer solutions.

Anderson, E. C.↗

NASA NTRS1991

A numerical investigation of turbulent baseflow

The turbulent base flow of a cone with a sting in hypersonic flow is investigated using a time-dependent Navier-Stokes code called UWIN. A PNS solver provides the upstream flow conditions which drive the development of the base flow. The computational method is described along with its application to the base flow problem. The grid generation and boundary conditions are described. The results and the summary conclude this note.

Chaussee, Denny S.↗

NASA NTRS2007

Mars Science Laboratory: Entry, Descent, and Landing System Performance

In 2010, the Mars Science Laboratory (MSL) mission will pioneer the next generation of robotic Entry, Descent, and Landing (EDL) systems, by delivering the largest and most capable rover to date to the surface of Mars. To do so, MSL will fly a guided lifting entry at a lift-to-drag ratio in excess of that ever flown at Mars, deploy the largest parachute ever at Mars, and perform a novel Sky Crane maneuver. Through improved altitude capability, increased latitude coverage, and more accurate payload delivery, MSL is allowing the science community to consider the exploration of previously inaccessible regions of the planet. The MSL EDL system is a new EDL architecture based on Viking heritage technologies and designed to meet the challenges of landing increasing massive payloads on Mars. In accordance with level-1 requirements, the MSL EDL system is being designed to land an 850 kg rover to altitudes as high as 1 km above the Mars Orbiter Laser Altimeter defined areoid within 10 km of the desired landing site. Accordingly, MSL will enter the largest entry mass, fly the largest 70 degree sphere-cone aeroshell, generate the largest hypersonic lift-to-drag ratio, and deploy the largest Disk-Gap-Band supersonic parachute of any previous mission to Mars. Major EDL events include a hypersonic guided entry, supersonic parachute deploy and inflation, subsonic heatshield jettison, terminal descent sensor acquisition, powered descent initiation, sky crane terminal descent, rover touchdown detection, and descent stage flyaway. Key performance metrics, derived from level-1 requirements and tracked by the EDL design team to indicate performance capability and timeline margins, include altitude and range at parachute deploy, time on radar, and propellant use. The MSL EDL system, which will continue to develop over the next three years, will enable a notable extension in the advancement of Mars surface science by delivering more science capability than ever before to the surface of Mars. This paper describes the current MSL EDL system performance as predicted by end-to-end EDL simulations, highlights the sensitivity of this baseline performance to several key environmental assumptions, and discusses some of the challenges faced in delivering such an unprecedented rover payload to the surface of Mars.

Way, David W.↗

NASA NTRS2006

Mars Science Laboratory: Entry, Descent, and Landing System Performance

In 2010, the Mars Science Laboratory (MSL) mission will pioneer the next generation of robotic Entry, Descent, and Landing (EDL) systems, by delivering the largest and most capable rover to date to the surface of Mars. To do so, MSL will fly a guided lifting entry at a lift-to-drag ratio in excess of that ever flown at Mars, deploy the largest parachute ever at Mars, and perform a novel Sky Crane maneuver. Through improved altitude capability, increased latitude coverage, and more accurate payload delivery, MSL is allowing the science community to consider the exploration of previously inaccessible regions of the planet. The MSL EDL system is a new EDL architecture based on Viking heritage technologies and designed to meet the challenges of landing increasing massive payloads on Mars. In accordance with level-1 requirements, the MSL EDL system is being designed to land an 850 kg rover to altitudes as high as 1 km above the Mars Orbiter Laser Altimeter defined areoid within 10 km of the desired landing site. Accordingly, MSL will enter the largest entry mass, fly the largest 70 degree sphere-cone aeroshell, generate the largest hypersonic lift-to-drag ratio, and deploy the largest Disk-Gap-Band supersonic parachute of any previous mission to Mars. Major EDL events include a hypersonic guided entry, supersonic parachute deploy and inflation, subsonic heatshield jettison, terminal descent sensor acquisition, powered descent initiation, sky crane terminal descent, rover touchdown detection, and descent stage flyaway. Key performance metrics, derived from level-1 requirements and tracked by the EDL design team to indicate performance capability and timeline margins, include altitude and range at parachute deploy, time on radar, and propellant use. The MSL EDL system, which will continue to develop over the next three years, will enable a notable extension in the advancement of Mars surface science by delivering more science capability than ever before to the surface of Mars. This paper describes the current MSL EDL system performance as predicted by end-to-end EDL simulations, highlights the sensitivity of this baseline performance to several key environmental assumptions, and discusses some of the challenges faced in delivering such an unprecedented rover payload to the surface of Mars.

Way, David W.↗

NASA NTRS1972

Hypersonic transitional boundary layers.

Surface thin-film gages have been used to determine the extent of the transition region, intermittency distribution, and disturbance convection velocities in the boundary layer on a sharp 5-deg half angle cone at Mach 7.4 in the Ames 3.5-ft Hypersonic Wind Tunnel. In addition, extensive hot wire space-time correlation measurements have been obtained in the wind-tunnel freestream and in the transitional hypersonic boundary layer on a cone-ogive-cylinder in the same facility. Disturbance convection velocities have been obtained from the longitudinal cross correlation measurements as a function of fluctuation scale and distance from the wall. The results of normal cross correlation measurements are also discussed.

Owen, F. K.↗

NASA NTRS1974

Experimental studies of hypersonic boundary-layer transition and effects of wind tunnel disturbances

Boundary layer transition data on cones and free stream disturbance levels were measured in a hypersonic wind tunnel and Mach 8 variable density hypersonic tunnel. Transition data were obtained by using different conical models and techniques for detecting the location of transition. The disturbance levels were measured by using hot wire anemometry and pressure transducers. The transition Reynolds numbers obtained from the tests correlated well when the fluctuating pressures measured at the surface of conical models were used as a correlating parameter.

Stainback, P. C.↗

NASA NTRSDate not supplied

Separation and Transition on the ROTEX-T Cone-Flare

As part of NATO STO AVT-346 “Predicting Hypersonic Boundary-Layer Transition on Complex Geometries,” coordinated experimental and computational studies were conducted on the ROTEX-T, a cone-flare geometry used in a successful flight-test experiment. At the as-flown conditions, a separation bubble existed at the compression corner. Separation, reattachment, and the multifaceted linear instability paths leading this bubble to transition to turbulence are challenging to predict, but have significant impact on surface pressure and heat flux. High-resolution background-oriented schlieren and infrared thermography measurements were made in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel at freestream unit Reynolds numbers from 5.8×10(exp 6) to 12.2×10(exp 6) m-1and nominally zero angle of attack. High-speed self-aligned focusing schlieren, infrared thermography, and focused laser differential interferometry measurements were made in the AFRL Mach-6 Ludwieg Tube from 2.2×10(exp 6) to 24.7×10(exp 6) m-1and nominally zero degrees angle of attack. The surface heat-flux and Stanton number distributions were computed. Separation and reattachment locations, as well as the flow state at each, were determined from the combination of surface and off-wall measurements. The convective and global boundary-layer instabilities of the axisymmetric laminar flow at the experimental conditions were investigated computationally. Amplification of Mack’s first and second modes were observed to have logarithmic amplification factors between 5 to 7.5 at the separation location, depending on conditions. The flow was found to be globally unstable to stationary three-dimensional disturbances concentrated in the reattachment region. Previous analysis of the ROTEX-T flight data had not assessed reattachment location or the flow state upon reattachment. Thanks to the insights gained from the coordinated, on- and off-wall ground-test measurements, these evaluations have now been made. The separation location indicated by laminar simulations is consistently numerically predicted to be upstream of the experimentally observed location for a transitional separation bubble. The cause of this difference is understood to lie in the steady-state and axisymmetric assumptions made by both solvers employed to compute the basic states analyzed, as flow topology considerations assert that unsteady two-dimensional or axisymmetric separation bubbles are structurally unstable and will become three-dimensional. Computed laminar heating rates prior to separation agreed well with experiment; transitional heating rates after reattachment were between laminar and turbulent computations.

CFD Validation↗

NASA NTRSDate not supplied

Separation and Transition on the ROTEX-T Cone-Flare

As part of NATO STO AVT-346 “Predicting Hypersonic Boundary-Layer Transition on Complex Geometries,” coordinated experimental and computational studies were conducted on the ROTEX-T, a cone-flare geometry used in a successful flight-test experiment. At the as-flown conditions, a separation bubble existed at the compression corner. Separation, reattachment, and the multifaceted linear instability paths leading this bubble to transition to turbulence are challenging to predict, but have significant impact on surface pressure and heat flux. High-resolution background-oriented schlieren and infrared thermography measurements were made in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel at freestream unit Reynolds numbers from 5.8×10(exp 6) to 12.2×10(exp 6) m-1and nominally zero angle of attack. High-speed self-aligned focusing schlieren, infrared thermography, and focused laser differential interferometry measurements were made in the AFRL Mach-6 Ludwieg Tube from 2.2×10(exp 6) to 24.7×10(exp 6) m-1and nominally zero degrees angle of attack. The surface heat-flux and Stanton number distributions were computed. Separation and reattachment locations, as well as the flow state at each, were determined from the combination of surface and off-wall measurements. The convective and global boundary-layer instabilities of the axisymmetric laminar flow at the experimental conditions were investigated computationally. Amplification of Mack’s first and second modes were observed to have logarithmic amplification factors between 5 to 7.5 at the separation location, depending on conditions. The flow was found to be globally unstable to stationary three-dimensional disturbances concentrated in the reattachment region. Previous analysis of the ROTEX-T flight data had not assessed reattachment location or the flow state upon reattachment. Thanks to the insights gained from the coordinated, on- and off-wall ground-test measurements, these evaluations have now been made. The separation location indicated by laminar simulations is consistently numerically predicted to be upstream of the experimentally observed location for a transitional separation bubble. The cause of this difference is understood to lie in the steady-state and axisymmetric assumptions made by both solvers employed to compute the basic states analyzed, as flow topology considerations assert that unsteady two-dimensional or axisymmetric separation bubbles are structurally unstable and will become three-dimensional. Computed laminar heating rates prior to separation agreed well with experiment; transitional heating rates after reattachment were between laminar and turbulent computations.

CFD Validation↗

NASA NTRS1974

Cross-flow effects on the boundary layer in a plane of symmetry

The validity of 'effective cone analysis' in estimating the boundary-layer properties of bodies in hypersonic flow is discussed. Simple formulas are derived for noncircular cones at angles of attack and are used to show that effective cone analysis only accounts for the increase in the local edge Reynolds number due to the angle of attack. A correction factor depending on the cross flow produced by the transverse curvature of the body and on the angle of attack is shown to reconcile the effective cone approach with the predictions of exact theory.

Agnone, A.↗

NASA NTRS1970

Aerodynamic interference effects on half-cone bodies with thin wings at Mach 10.03

Aerodynamic interference effects on half-cone bodies with thin wings in hypersonic flow

Townsend, J. C.↗

NASA NTRS1975

Viscous-shock-layer solutions for turbulent flow of radiating gas mixtures in chemical equilibrium

The viscous-shock-layer equations for hypersonic laminar and turbulent flows of radiating or nonradiating gas mixtures in chemical equilibrium are presented for two-dimensional and axially-symmetric flow fields. Solutions were obtained using an implicit finite-difference scheme and results are presented for hypersonic flow over spherically-blunted cone configurations at freestream conditions representative of entry into the atmosphere of Venus. These data are compared with solutions obtained using other methods of analysis.

Anderson, E. C.↗

NASA NTRS1987

Direct simulation of aerothermal loads for an aeroassist flight experiment vehicle

Results of a numerical study using the direct simulation Monte Carlo (DSMC) method are presented for the hypersonic flow about an elliptically blunted cone. The flow conditions are those for a proposed Aeroassist Flight Experiment (AFE) vehicle. The altitude range considered is that from 130 to 90 km which encompasses most of the transitional flow regime for the AFE vehicle, that is, the region bounded by free molecular and continuum flow. Freestream velocities of 9.9 to 7.5 km/sec are considered. The numerical simulations show that noncontinuum effects are evident for all cases considered. The onset of chemical dissociation occurs at a simulated altitude of about 130 km. Results presented highlight the thermal and chemical nonequilibrium nature of the flowfield and the impact of these effects on the surface heating and body drag. A calculation which included the additional effects of ionization and thermal radiation demonstrates that the inclusion of such efects would not significantly alter the surface quantities calculated in the present study. The radiative heating is negligible when compared with the convective heating, and the same would be true for the other conditions considered.

Dogra, Virendra K.↗

NASA NTRS1988

Explicit upwind algorithm for the parabolized Navier-Stokes equations

A new explicit upwind algorithm based on Roe's flux-difference splitting (FDS) method has been developed for the three-dimensional Parabolized Navier-Stokes (PNS) equations. For three-dimensional flows, FDS's are determined separately for the two nonmarching directions and modified to account for the calculated shock angle in the crossflow plane. Second-order FDS is applied to the pressure and convection terms with the streamwise pressure gradient limited in the subsonic region to maintain a hyperbolic inviscid equation set. Second-order central differencing is obtained in the two-step algorithm for the shear and heat flux terms. The new algorithm is demonstrated for three laminar flow test cases: supersonic flow over a flat plate, hypersonic flow over a 15 deg ramp, and hypersonic flow past a 10 deg cone at a 24 deg angle of attack. The computed results agree well with experimental measurements.

Korte, John J.↗

NASA NTRS1991

Numerical flux formulas for the Euler and Navier-Stokes equations. 2: Progress in flux-vector splitting

The accuracy of various numerical flux functions for the inviscid fluxes when used for Navier-Stokes computations is studied. The flux functions are benchmarked for solutions of the viscous, hypersonic flow past a 10 degree cone at zero angle of attack using first order, upwind spatial differencing. The Harten-Lax/Roe flux is found to give a good boundary layer representation, although its robustness is an issue. Some hybrid flux formulas, where the concepts of flux-vector and flux-difference splitting are combined, are shown to give unsatisfactory pressure distributions; there is still room for improvement. Investigations of low diffusion, pure flux-vector splittings indicate that a pure flux-vector splitting can be developed that eliminates spurious diffusion across the boundary layer. The resulting first-order scheme is marginally stable and not monotone.

Coirier, William J.↗

NASA NTRS1991

Numerical flux formulas for the Euler and Navier-Stokes equations. II - Progress in flux-vector splitting

The accuracy of various numerical flux functions for the inviscid fluxes when used for Navier-Stokes computations is studied. The flux functions are benchmarked for solutions of the viscous, hypersonic flow past a 10 degree cone at zero angle of attack using first order, upwind spatial differencing. The Harten-Lax/Roe flux is found to give a good boundary layer representation, although its robustness is an issue. Some hybrid flux formulas, where the concepts of flux-vector and flux-difference splitting are combined, are shown to give unsatisfactory pressure distributions; there is still room for improvement. Investigations of low diffusion, pure flux-vector splittings indicate that a pure flux-vector splitting can be developed that eliminates spurious diffusion across the boundary layer. The resulting first-order scheme is marginally stable and not monotone.

Coirier, William J.↗

NASA NTRS1991

Viscous equilibrium computations using program LAURA

The Langley Aerothermodynamic Upwind Relaxation Algorithm (LAURA) has been modified to compute viscous equilibrium flow. Periodic calls to the thermodynamic and transport property curve-fits enable solutions to be computed for small percentage increase in computer time when compared with perfect gas times. The code is used to compute the hypersonic flow over slender and blunt cones, and solutions are compared with other computational techniques and flight data.

Greene, Francis A.↗

NASA NTRS2010

Design of Modular, Shape-transitioning Inlets for a Conical Hypersonic Vehicle

For a hypersonic vehicle, propelled by scramjet engines, integration of the engines and airframe is highly desirable. Thus, the forward capture shape of the engine inlet should conform to the vehicle body shape. Furthermore, the use of modular engines places a constraint on the shape of the inlet sidewalls. Finally, one may desire a combustor cross- section shape that is different from that of the inlet. These shape constraints for the inlet can be accommodated by employing a streamline-tracing and lofting technique. This design technique was developed by Smart for inlets with a rectangular-to-elliptical shape transition. In this paper, we generalise that technique to produce inlets that conform to arbitrary shape requirements. As an example, we show the design of a body-integrated hypersonic inlet on a winged-cone vehicle, typical of what might be used in a three-stage orbital launch system. The special challenge of inlet design for this conical vehicle at an angle-of-attack is also discussed. That challenge is that the bow shock sits relatively close to the vehicle body.

Gollan, Rowan J.↗

NASA NTRS1987

Prediction and control of transition in hypersonic boundary layers

In this paper, the role of compressible linear stability theory in prediction of boundary layer transition at supersonic and hypersonic speeds is investigated. Computations for sharp cones, using the e exp N method with N = 10, show that the first oblique Tollmien-Schlichting mode is responsible for transition at adiabatic wall conditions for freestream Mach numbers up to 7. For cold walls, the two-dimensional second mode dominates the transition process at lower hypersonic Mach numbers due to the well-known destabilizing effect of cooling on the second mode. It is shown that pressure gradient and suction may be used to stabilize this mode. Some results on the real gas effects on hypersonic boundary-layer stability are presented.

Malik, Mujeeb R.↗