Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Hybrid Work”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Dynamic Analysis of the hFan, a Parallel Hybrid Electric Turbofan Engine

NASA and a variety of aerospace industry stakeholders are investing in conceptual studies of electrified aircraft, including parallel hybrid electric aircraft such as the Subsonic Ultra Green Aircraft Research (SUGAR) Volt. At this point, little of the work published in the literature has examined the transient behavior of the turbomachinery in these systems. This paper describes a control system built around the hFan, the parallel hybrid electric turbofan engine designed for the SUGAR Volt concept aircraft. This control system is used to show that the hFan, running with its baseline concept of operations, is capable of transient operation throughout the envelope. The design parameters of this controller are varied to assess the amount of operability margin built into the engine design, and whether this margin can be reduced to enable more aggressive designs, that may feature better fuel economy. Further, studies are performed as parameters for the hFan electric motor are varied to determine how the motor impacts the engine's need for transient operability margin. The studies suggest that the engine may be redesigned with as much as a 3% reduction in high pressure compressor stall margin. It was also demonstrated that appropriate design and control of the electric motor may be able to buy an additional 0.5% stall margin reduction or a turbine inlet temperature reduction of 35 R, as tested at the sea-level static condition.

SUGAR Volt↗
NASA NTRS2019

Composites for Advanced Drive Systems, A Systems Analysis-Revolutionary Vertical Lift Technology (RVLT)

Rotorcraft propulsion systems are continually looking to improve power density; that is reducing weight and increasing power throughput. In order to advance rotorcraft propulsion system technology, NASA Glenn Research Center (NGRC) contracted Boeing Vertical Lift (Contract #NNA15AB12B, Task Order NNA16BE07T) to perform system level benefit assessments for incorporation of composite materials into rotorcraft transmission gear and shaft systems, in the rotating frame. In general, the environment inside a typical rotorcraft transmission is aggressive for typical composite materials. Design challenges in the rotating frame and related safety risks must be understood and accounted for in the design. Boeing developed a technical approach that evaluated a relatively large population of rotorcraft main transmissions. This technical approach took rotorcraft from various size classes and configurations and applied parametric weight estimating principles to assess the performance impact of composite hybrid technologies inside transmissions, in the rotating frame. Parametric weight estimates showed that composite hybrid technologies account for an average 9% weight savings over the baseline transmissions. More weight savings may be observed when accounting for quantity of transmissions in an aircraft configuration and benefits to airframe, landing gear, and fuel systems. A weight reduction of 595 lbs was calculated for NASA's Large Civil Tilt Rotor (LCTR2) by utilizing composite hybrid components inside the Prop-Rotor Transmission in the rotating frame and accounting for design changes to the airframe, landing gear, and fuel system. In order to develop composite hybrid technologies, sub-scale and full-scale testing should continue, building on the work that NGRC has begun. Design and testing efforts should focus on technical challenges, such as joint and attachment interfaces, temperature effects, inspection procedures, and fault detection. It is recommended to address technical challenges with targeted research and development efforts, conducted at relevant scale, prior to incorporating composite hybrid technologies within the rotating frame of helicopter transmissions.

Darmstadt, Patrick R.↗
NASA NTRS1999

Fabrication Of Carbon-Boron Reinforced Dry Polymer Matrix Composite Tape

Future generation aerospace vehicles will require specialized hybrid material forms for component structure fabrication. For this reason, high temperature composite prepregs in both dry and wet forms are being developed at NASA Langley Research Center (LaRC). In an attempt to improve compressive properties of carbon fiber reinforced composites, a hybrid carbon-boron tape was developed and used to fabricate composite laminates which were subsequently cut into flexural and compression specimens and tested. The hybrid material, given the designation HYCARB, was fabricated by modifying a previously developed process for the manufacture of dry polymer matrix composite (PMC) tape at LaRC. In this work, boron fibers were processed with IM7/LaRC(TradeMark)IAX poly(amide acid) solution-coated prepreg to form a dry hybrid tape for Automated Tow Placement (ATP). Boron fibers were encapsulated between two (2) layers of reduced volatile, low fiber areal weight poly(amide acid) solution-coated prepreg. The hybrid prepreg was then fully imidized and consolidated into a dry tape suitable for ATP. The fabrication of a hybrid boron material form for tow placement aids in the reduction of the overall manufacturing cost of boron reinforced composites, while realizing the improved compression strengths. Composite specimens were press-molded from the hybrid material and exhibited excellent mechanical properties.

Belvin, Harry L.↗
NASA NTRS1992

Grid generation research at OSU

In the last two years, effort was concentrated on: (1) surface modeling; (2) surface grid generation; and (3) 3-D flow space grid generation. The surface modeling shares the same objectives as the surface modeling in computer aided design (CAD), so software available in CAD can in principle be used for solid modeling. Unfortunately, however, the CAD software cannot be easily used in practice for grid generation purposes, because they are not designed to provide appropriate data base for grid generation. Therefore, we started developing a generalized surface modeling software from scratch, that provides the data base for the surface grid generation. Generating surface grid is an important step in generating a 3-D space for flow space. To generate a surface grid on a given surface representation, we developed a unique algorithm that works on any non-smooth surfaces. Once the surface grid is generated, a 3-D space can be generated. For this purpose, we also developed a new algorithm, which is a hybrid of the hyperbolic and the elliptic grid generation methods. With this hybrid method, orthogonality of the grid near the solid boundary can be easily achieved without introducing empirical fudge factors. Work to develop 2-D and 3-D grids for turbomachinery blade geometries was performed, and as an extension of this research we are planning to develop an adaptive grid procedure with an interactive grid environment.

Nakamura, S.↗
NASA NTRS1987

A hybrid-stress finite element approach for stress and vibration analysis in linear anisotropic elasticity

A hybrid stress finite element method is developed for accurate stress and vibration analysis of problems in linear anisotropic elasticity. A modified form of the Hellinger-Reissner principle is formulated for dynamic analysis and an algorithm for the determination of the anisotropic elastic and compliance constants from experimental data is developed. These schemes were implemented in a finite element program for static and dynamic analysis of linear anisotropic two dimensional elasticity problems. Specific numerical examples are considered to verify the accuracy of the hybrid stress approach and compare it with that of the standard displacement method, especially for highly anisotropic materials. It is that the hybrid stress approach gives much better results than the displacement method. Preliminary work on extensions of this method to three dimensional elasticity is discussed, and the stress shape functions necessary for this extension are included.

Oden, J. Tinsley↗
NASA NTRS2003

Impact Resistance of Lightweight Hybrid Structures for Gas Turbine Engine Fan Containment Applications

The ballistic impact resistance of hybrid composite sandwich structures was evaluated with the ultimate goal of developing new materials or structures for potential gas turbine engine fan containment applications. The sandwich structures investigated consisted of GLARE-5 laminates as face sheets with lightweight cellular metallic materials such as honeycomb, foam, and lattice block as a core material. The impact resistance of these hybrid sandwich structures was compared to GLARE-5 laminates and 2024-T3 Al sheet, which were tested as a function of areal weight (material thickness). The GLARE-5 laminates exhibited comparable impact properties to that of 2024-T3 Al at low areal weights, even though there were significant differences in the static tensile properties of these materials. The GLARE-5, however, did have a greater ballistic limit than straight aluminum sheet at higher areal weights. Furthermore, there is up to a 25% advantage in ballistic limit for the GLARE-5/foam sandwich structures compared to straight 2024-T3 Al. But no advantage in ballistic limit was observed between any of the hybrid sandwich structures and thicker versions of GLARE-5. Recommendations for future work are provided, based on these preliminary data.

Hebsur, Mohan G.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-33512-DND

INTRODUCTION: In an effort to quantify the predictive capability of the Livermore Software Technology Corporation (LSTC)-provided Hybrid III (small female, mid-size male, and large male) anthropomorphic test device (ATD) finite element models (FEMs) within aerospace loading environments, the National Aeronautics and Space Administration (NASA) performed a series of sled tests with the isolated head-neck complex of each ATD. These tests and subsequent modeling efforts revealed significant deficiencies in the large male head neck FEM. Differences in both the shape and material properties between the FEM and the physical ATD were identified. In order to improve the predictive response of the FEM, a model development effort was undertaken to update the head-neck complex to better represent the geometric and material properties of the physical ATD.METHODS: To better match the physical geometry, a new neck component model was meshed and implemented into the Hybrid III large male head-neck complex. The updated geometry and weight were verified against measurements of the physical ATD to insure accuracy. The primary source of material discrepancy between the physical ATD and FEM was found to be in the material definition of the rubber neck pucks. Using LS-Opt the material properties of this part were calibrated to match physical response of the head-neck complex in the isolated head-neck testing performed. RESULTS AND DISCUSSION: The updated geometry and calibrated material properties were shown to significantly improve the FEM predictive accuracy under lateral, rear, and frontal impacts with combined horizontal and vertical loading. The results of this study demonstrate an effective means for improving ATD FEM response through isolated component level testing and material parameter optimization. The improved and quantified accuracy of the Hybrid III large male FEM head-neck complex stemming from with work lends to confidence in its future use for occupant protection evaluation of large male occupants

J Putnam↗
NASA NTRSDate not supplied

An Improved Impedance Eduction Process for the NASA Langley GFIT

The Grazing Flow Impedance Tube (GFIT) is regularly employed to characterize the frequency response of acoustic liners through the eduction of their specific acoustic impedance. Acoustic pressures acquired in the facility are processed with various eduction methods to arrive at these impedance values. Recent implementation of the Swept-Sine Method provides much greater frequency resolution when characterizing the acoustic properties of a liner. The attendant increase in data that must be processed from this method has highlighted a need for greater efficiency in educing acoustic impedance. The current work details efforts to improve the eduction process through use of a hybrid approach that combines a Prony-based method with the Convected Helmholtz-based calculation generally used for this type of data. Comparisons of efficiency and accuracy are shown for this new hybrid approach versus earlier methods for three acoustic liners tested under various conditions in the GFIT with stepped-sine and recently implemented swept-sine sources.

Eduction↗
NASA NTRS1983

A comparison of methods for computing the sigma-coordinate pressure gradient force for flow over sloped terrain in a hybrid theta-sigma model

In connection with the employment of the sigma coordinates introduced by Phillips (1957), problems can arise regarding an accurate finite-difference computation of the pressure gradient force. Over steeply sloped terrain, the calculation of the sigma-coordinate pressure gradient force involves computing the difference between two large terms of opposite sign which results in large truncation error. To reduce the truncation error, several finite-difference methods have been designed and implemented. The present investigation has the objective to provide another method of computing the sigma-coordinate pressure gradient force. Phillips' method is applied for the elimination of a hydrostatic component to a flux formulation. The new technique is compared with four other methods for computing the pressure gradient force. The work is motivated by the desire to use an isentropic and sigma-coordinate hybrid model for experiments designed to study flow near mountainous terrain.

Johnson, D. R.↗
NASA NTRS2005

Diagnosing Hybrid Systems: a Bayesian Model Selection Approach

In this paper we examine the problem of monitoring and diagnosing noisy complex dynamical systems that are modeled as hybrid systems-models of continuous behavior, interleaved by discrete transitions. In particular, we examine continuous systems with embedded supervisory controllers that experience abrupt, partial or full failure of component devices. Building on our previous work in this area (MBCG99;MBCG00), our specific focus in this paper ins on the mathematical formulation of the hybrid monitoring and diagnosis task as a Bayesian model tracking algorithm. The nonlinear dynamics of many hybrid systems present challenges to probabilistic tracking. Further, probabilistic tracking of a system for the purposes of diagnosis is problematic because the models of the system corresponding to failure modes are numerous and generally very unlikely. To focus tracking on these unlikely models and to reduce the number of potential models under consideration, we exploit logic-based techniques for qualitative model-based diagnosis to conjecture a limited initial set of consistent candidate models. In this paper we discuss alternative tracking techniques that are relevant to different classes of hybrid systems, focusing specifically on a method for tracking multiple models of nonlinear behavior simultaneously using factored sampling and conditional density propagation. To illustrate and motivate the approach described in this paper we examine the problem of monitoring and diganosing NASA's Sprint AERCam, a small spherical robotic camera unit with 12 thrusters that enable both linear and rotational motion.

McIlraith, Sheila A.↗
NASA NTRS2018

Low Temperature Hybrid Mars Ascent Vehicle Concept Development and Planning at MSFC

Return of samples from Mars has been a goal of NASA's for decades. The current Mars Sample Return mission concepts have a multiple launch rocket from the earth, where one mission delivers a caching rover to collect and package the Martian soil samples. Another rocket sends the Mars Ascent Vehicle that takes those samples to orbit. Another rocket sends an orbiter, that also meets up with the samples in orbit, and brings them back to earth. Our tasks have been focused on the Mars Ascent Vehicle. To leave the Martian surface, it requires a two burn trajectory, one to get off the planet and another to circularize the orbit. Recent studies have led to the investigation of a hybrid rocket solution. That technology has been under development for several years. This paper will discuss some of the work going on at MSFC to understand how to process the fuel, some test firings done to characterize some design features and some planning done to scope out what it would take to qualify a hybrid rocket motor for this application.

Story, George↗
NASA NTRS2018

Hybrid Reduced Order Model for N2-N2 Interactions for Application to Dissociation and Energy Transfer Processes

This work presents a general framework for model reduction of non-equilibrium energy transfer and dissociation processes. The multi-group maximum-entropy method is coupled with the quasi-classical trajectory method to directly construct a reduced order model for chemical non-equilibrium. Kinetic data is calculated by applying detailed balance at a microscopic level, overcoming the limitation of calculating recombination kinetic data. This approach enables the construction of a reduced order model for kinetics which bypasses the need to compute state-to-state kinetic data. This physics based reduced order model ensures that an equilibrium distribution is reached given infinite time, while allowing for non-equilibrium distributions during the relaxation and dissociation processes. A proof-of-concept test case demonstrates the applicability of this model by comparison with state-to-state kinetic data for the N2(Chi (sup 1) Sigma ((sub g), (sup plus sign)) minus N ((exp 4) S (sub u)) system with excellent agreement.

Maximum Entropy↗
NASA NTRS1991

Areas of Seal R/D at GE

About four years ago, work was completed on a 36 inch diameter gas to gas carbon ring seal used to buffer low pressure turbine air at the rim of the forward outer flowpath on the GE36 unducted fan (UDF) engine. At about the same time, we were developing a long life counter-rotating intershaft air-oil seal of approximately 7.6 inch diameter for operation at 800 fps, 800 F, and 50 psid. Although we were successful in meeting most program goals with a split ring seal of the axial bushing type, the seal with the greatest payoff in life and air leakage rates, bearing many features in common with the GE36 seal, could not be successfully tested because of the structural weakness of the primary seal ring carbon material. This was a split ring seal using a hybrid combination of orifice compensated hydrostatic and shrouded hydrodynamic gas bearings. We are presently working to develop this design in conjunction with high strength materials being developed by Pure Carbon Co. In the area of engine secondary gas flow path-sealing for performance improvement, we are currently working with carbon and all metal face seals. A 15 inch diameter all metal 'aspirating' face seal, using self-acting hydrostatic bearings, was successfully tested to 700 fps, 100 psid, and 1000 F, demonstrating long life at flow reduction of 86 percent compared to a 'best' labyrinth. This seal will be developed through 1400 F, 900 fps, and 350 psid. The seal 'aspirates' closed at about idle speed pressure during engine start and reopens at engine shutdown. A hydraulic thrust balance seal, currently using orifice compensated hydrostatics, is under development. Other aspects of these projects are briefly covered.

Pope, A. Nelson↗
NASA NTRS1975

Advances in superconducting quantum electronic microcircuit fabrication

Standard microelectronic fabrication techniques have been utilized to produce batch quantities of superconducting quantum electronic devices and circuits. The overall goal is a fabrication technology yielding circuits that are rugged and stable and capable of being fabricated controllably and reproducibly in sizeable quantities. Our progress toward this goal is presented, with primary emphasis on the most recent work, which includes the use of electron-beam lithography and techniques of hybrid microelectronics. Several prototype microcircuits have been successfully fabricated. These microcircuits are formed in a thin-film parent material consisting of layers of superconducting and normal metals, and use proximity-effect structures as the active circuit elements.

Kirschman, R. K.↗
NASA NTRS2002

Performance of OVERFLOW-D Applications based on Hybrid and MPI Paradigms on IBM Power4 System

This report briefly discusses our preliminary performance experiments with parallel versions of OVERFLOW-D applications. These applications are based on MPI and hybrid paradigms on the IBM Power4 system here at the NAS Division. This work is part of an effort to determine the suitability of the system and its parallel libraries (MPI/OpenMP) for specific scientific computing objectives.

Djomehri, M. Jahed↗
NASA NTRS2004

A Massively Parallel Hybrid Dusty-Gasdynamics and Kinetic Direct Simulation Monte Carlo Model for Planetary Applications

In order to understand the global structure, dynamics, and physical and chemical processes occurring in the upper atmospheres, exospheres, and ionospheres of the Earth, the other planets, comets and planetary satellites and their interactions with their outer particles and fields environs, it is often necessary to address the fundamentally non-equilibrium aspects of the physical environment. These are regions where complex chemistry, energetics, and electromagnetic field influences are important. Traditional approaches are based largely on hydrodynamic or magnetohydrodynamic (MHD) formulations and are very important and highly useful. However, these methods often have limitations in rarefied physical regimes where the molecular collision rates and ion gyrofrequencies are small and where interactions with ionospheres and upper neutral atmospheres are important. At the University of Michigan we have an established base of experience and expertise in numerical simulations based on particle codes which address these physical regimes. The Principal Investigator, Dr. Michael Combi, has over 20 years of experience in the development of particle-kinetic and hybrid kinetichydrodynamics models and their direct use in data analysis. He has also worked in ground-based and space-based remote observational work and on spacecraft instrument teams. His research has involved studies of cometary atmospheres and ionospheres and their interaction with the solar wind, the neutral gas clouds escaping from Jupiter s moon Io, the interaction of the atmospheres/ionospheres of Io and Europa with Jupiter s corotating magnetosphere, as well as Earth s ionosphere. This report describes our progress during the year. The contained in section 2 of this report will serve as the basis of a paper describing the method and its application to the cometary coma that will be continued under a research and analysis grant that supports various applications of theoretical comet models to understanding the inner comae of comets (grant NAGS- 13239 from the Planetary Atmospheres program).

Combi, Michael R.↗
NASA NTRS2014

Validation of the 5th and 95th Percentile Hybrid III Anthropomorphic Test Device Finite Element Model

NASA spacecraft design requirements for occupant protection are a combination of the Brinkley criteria and injury metrics extracted from anthropomorphic test devices (ATD's). For the ATD injury metrics, the requirements specify the use of the 5th percentile female Hybrid III and the 95th percentile male Hybrid III. Furthermore, each of these ATD's is required to be fitted with an articulating pelvis and a straight spine. The articulating pelvis is necessary for the ATD to fit into spacecraft seats, while the straight spine is required as injury metrics for vertical accelerations are better defined for this configuration. The requirements require that physical testing be performed with both ATD's to demonstrate compliance. Before compliance testing can be conducted, extensive modeling and simulation are required to determine appropriate test conditions, simulate conditions not feasible for testing, and assess design features to better ensure compliance testing is successful. While finite element (FE) models are currently available for many of the physical ATD's, currently there are no complete models for either the 5th percentile female or the 95th percentile male Hybrid III with a straight spine and articulating pelvis. The purpose of this work is to assess the accuracy of the existing Livermore Software Technology Corporation's FE models of the 5th and 95th percentile ATD's. To perform this assessment, a series of tests will be performed at Wright Patterson Air Force Research Lab using their horizontal impact accelerator sled test facility. The ATD's will be placed in the Orion seat with a modified-advanced-crew-escape-system (MACES) pressure suit and helmet, and driven with loadings similar to what is expected for the actual Orion vehicle during landing, launch abort, and chute deployment. Test data will be compared to analytical predictions and modelling uncertainty factors will be determined for each injury metric. Additionally, the test data will be used to further improve the FE model, particularly in the areas of the ATD neck components, harness, and suit and helmet effects.

Lawrence, C.↗
NASA NTRS2016

Green Monopropellant Status at Marshall Space Flight Center

NASA Marshall Space Flight Center is continuing investigations into the use of green monopropellants as a replacement for hydrazine in spacecraft propulsion systems. Work to date has been to push technology development through multiple activities designed to understand the capabilities of these technologies. Future work will begin to transition to mission pull as these technologies are mature while still keeping a solid goal of pushing technology development as opportunities become available. The AF-M315E activities began with hot-fire demonstration testing of a 1N monopropellant thruster in FY 14 and FY15. Following successful completion of the preliminary campaign, changes to the test stand to accommodate propellant conditioning capability and better control of propellant operations was incorporated to make testing more streamlined. The goal is to conduct hot-fire testing with warm and cold propellants using the existing feed system and original thruster design. Following the 1N testing, a NASA owned 100 mN thruster will be hot-fire tested in the same facility to show feasibility of scaling to smaller thrusters for cubesat applications. The end goal is to conduct a hot-fire test of an integrated cubesat propulsion system using an SLM printed propellant tank, an MSFC designed propulsion system electronic controller and the 100 mN thruster. In addition to the AF-M315E testing, MSFC is pursuing hot-fire testing with LMP-103S. Following our successful hot-fire testing of the 22N thruster in April 2015, a test campaign was proposed for a 440N LMP-103S thruster with Orbital ATK and Plasma Processes. This activity was funded through the Space Technology Mission Directorate (STMD) ACO funding call in the last quarter of CY15. Under the same funding source a test activity with Busek and Glenn Research Center for testing of 5N AF-M315E thrusters was proposed and awarded. Both activities are in-work with expected completion of hot-fire testing by the end of FY17. MSFC is continuing to coordinate with the AF and academia on understanding the chemical reactions that occur in AF-M315E. An on-going investigation of the catalyst bed species using Raman Spectroscopy through the NASA Technology Research Fellowship Program (NSTRF) is looking for ways to minimize the amount of computation required by understanding the intermediate species created in the catalyst bed. The MSFC team is also working with commercial partners through Cooperative Agreement Notices (CAN's). Partnerships with commercial and academia include work in non-catalytic ignition of AF-M315, spark ignition of hybrid cubesat systems, printed SLM tanks, and dual-mode (electric and chemical) propulsion systems is continuing.

Burnside, Christopher G.↗