Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HARDENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Strain hardening magnesium-silicate-hydrate composites (SHMSHC) reinforced with short and randomly oriented polyvinyl alcohol microfibers

Magnesium-silicate-hydrate (M-S-H) cement has emerged as an alternative binder with potentially lower energy requirements and emissions. Due to the intrinsically low pH values of its matrix, however, normal steel reinforcement is not appropriate for M-S-H system. To toughen the matrix and to overcome the brittle nature of the material, a new strain hardening magnesium-silicate-hydrate composite (SHMSHC) is developed for the first time by incorporating 2 vol% short and randomly oriented polyvinyl alcohol (PVA) microfibers. The resulting SHMSHC exhibits significant strain hardening with a tensile strain capacity of more than 3%, a compressive strength beyond 50 MPa and a tensile strength of around 3 MPa. Remarkably, saturated multiple cracking with a tight crack width less than 10 μm invisible to the human naked eyes was observed. The newly developed SHMSHC addresses the fundamental challenge of M-S-H binder and is expected to widen possible application areas of M-S-H system.

36 MATERIALS SCIENCE↗

3D-printable engineered cementitious composites (3DP-ECC): Fresh and hardened properties

3D printing (3DP) is an emerging digital construction method for concrete materials. A major impediment to efficient 3D concrete printing (3DCP) is the need for steel reinforcement, the placement of which is incompatible with the 3DP process. Unlike plain concrete, ductile self-reinforced engineered cementitious composite (ECC) holds promise to remove the dependence on steel reinforcement. The objective of this research is to develop a 3D-printable ECC (3DP-ECC). The fresh rheological and hardened mechanical properties of 3DP-ECC are investigated. The robotically printed tensile specimens demonstrated the familiar multiple microcracking and strain-hardening behavior of conventionally cast ECC. Significant orthotropy is revealed in the compressive properties. The interface between printed layers is found to be toughened by a printed groove-tongue joint. The developed 3DP-ECC was used to print a twisted column with 150 layers, reaching a height of 1.5 m. This research lays the groundwork for efficient robotically 3D-printed structures of complex shapes.

36 MATERIALS SCIENCE↗

Fracture properties and microstructure formation of hardened alkali-activated slag/fly ash pastes

This study presents a comprehensive experimental investigation on the fracture properties of hardened alkali-activated slag/fly ash (AASF) pastes in relation to the microstructure formation and reaction product composition. The main reaction product in AASF is C-(N-)A-S-H gel along with minor hydrotalcite phase, with the polymerization of C-(N-)A-S-H gel substantially governed by its Ca/Si ratio. Strong positive correlations are identified between the Ca/Si ratios of C-(N-)A-S-H gel and the fracture properties K{sub Ic} (J{sub tip}), whereas, the compressive strength of AASF pastes is primarily determined by its capillary porosity (>0.01 μm). The disagreements between the Ca/Si ratios and corresponding intrinsic mechanical properties of C-(N-)A-S-H gel as proof by contradiction indicate that the fracture properties K{sub Ic} (J{sub tip}) of AASF pastes could be dominated by a cohesion/adhesion-based mechanism. These findings provide promising guidance for fine-tuning the fracture properties of AASF and also advise on the tailoring strategies for high-performance composite such as strain-hardening geopolymer composite.

36 MATERIALS SCIENCE↗

A review of the effect of nanoclays on the fresh and hardened properties of cement-based materials

This paper provides an overview of the use of nanoclays in cement-based materials. The effect of nanoclays on shear rheological properties will be discussed, with a focus on structural build-up behavior. This macroscale flow behavior will then be tied to the effect of nanoclays on the fresh microstructure as characterized via in-situ particle size measurements and rheological techniques. This will provide insight on the mechanisms underlying the effect of nanoclays on fresh state properties through an improved understanding of their effect on flocculation and coagulation behavior. In addition, secondary effects nanoclays have on the hardening and hardened properties will also be discussed. Examples of casting applications in which nanoclays have been effectively utilized as rheological modifiers, i.e. reducing self-consolidating concrete formwork pressure, extrusion, semi-flowable concrete for slipform paving, and 3D concrete printing, will be presented. Finally, some thoughts on potential directions for future work will be shared.

36 MATERIALS SCIENCE↗

A high-order, localized-artificial-diffusivity method for Eulerian simulation of multi-material elastic-plastic deformation with strain hardening

A high-order method for Eulerian simulation of material undergoing large elastic–plastic deformation is developed. Thermodynamically consistent hyperelastic constitutive relations are assumed, facilitating the treatment of solids, liquids, and gases in a unified manner. Here, the method enables the simulation of multi-material interactions using a diffuse interface approach. Numerical capturing of material interfaces, shock waves, contact surfaces, and elastic-plastic strain discontinuities using high-order compact-difference schemes is assisted by Localized Artificial Diffusivity (LAD). In the new setting involving elastic–plastic deformation, the previously established terms for the artificial properties are verified to effectively regularize normal shocks. Additional LAD terms are introduced to the elastic and plastic kinematic equations to regularize shear shocks and other strain discontinuities, improving solution stability. Other important features of the method that improve robustness include the numerical treatment of compatibility terms in the kinematic equations, and the treatment of rotation. Particular emphasis is focused toward new advancements of the methods for plastic-deformation integration and the associated strain hardening of the material, including rate-dependent plasticity. The method is demonstrated on a variety of test problems, including 1-D impacts, a variant of the Shu-Osher problem, a Taylor impact, and a Richtmyer-Meshkov instability between two elastic–plastic solids with strain hardening.

42 ENGINEERING↗

Twinning-mediated work hardening and texture evolution in CrCoFeMnNi high entropy alloys at cryogenic temperature

The cryogenic plastic deformation of CrCoFeMnNi high entropy alloy is characterized by three distinct stages based on the change of the work hardening rate. Microstructure and bulk texture at different strain levels were studied by electron backscatter diffraction (EBSD) and neutron diffraction. Our findings indicate that the deformation twins led to the constant work hardening rate at Stage II and resulted in the appearance of <115 >//TA texture component, while the dislocation slip was involved all though the entire plastic deformation. As a result, the twinning-mediated tensile plastic deformation at cryogenic temperature finally induced the strong {111}- < 112 > texture component and minor {001} < 110 > texture component accompanied with twinning-induced {115}< 552 > texture component.

36 MATERIALS SCIENCE↗

Age hardening response of Cu-30Ni alloys: The role of Si microalloying additions

Cu-30Ni alloys offer high strength and excellent corrosion resistance for maritime applications. While primarily a solid solution system, industrial alloys typically include microalloying additions of Fe, Mn, Nb and/or Si to enable age hardening. However, an understanding of the microstructural evolution during age hardening remains incomplete. Here, we conduct systematic ageing treatments and report the resulting hardness and microstructures. The Cu-30Ni alloy with Si aged at 650 °C for 6 h demonstrates significantly enhanced Vickers hardness, reaching ∼201 HV 1 compared to 103 HV 1 for the as-homogenised sample. Si-rich clusters and γ′ precipitates are identified, with their composition, size, and volume fraction quantified to determine their strengthening contributions. First-principles atomistic simulations elucidate the underlying formation mechanisms of these clusters and precipitates, highlighting the critical role of Si in driving their nucleation and growth. This study advances the design of high-strength, Cu alloys with the potential for corrosion resistance in demanding maritime environments.

Age hardening↗

Hardness-based plasticity and fracture model for quench-hardenable boron steel (22MnB5)

A comprehensive strain hardening and fracture characterization of different grades of boron steel blanks has been performed, providing the foundation for the implementation into the modular material model (MMM) framework developed by Volkswagen Group Research for an explicit crash code. Due to the introduction of hardness-based interpolation rules for the characterized main grades, the hardening and fracture behavior is solely described by the underlying Vickers hardness. In other words, knowledge of the hardness distribution within a hot-formed component is enough to set up the newly developed computational model. The hardness distribution can be easily introduced via an experimentally measured hardness curve or via hardness mapping from a corresponding hot-forming simulation. For industrial application using rather coarse and computationally inexpensive shell element meshes, the user material model has been extended by a necking/post-necking model with reduced mesh-dependency as an additional failure mode. The present paper mainly addresses the necking/post-necking model.

36 MATERIALS SCIENCE↗

Beam hardening and smoothing correction effects on performance of micro-ct SkyScan 1173 for imaging low contrast density materials

We have designed and fabricated phantom mimicking breast cancer composition known as a region that has low contrast density. The used compositions are a microcalcifications, fatty tissues and tumor mass by using Al{sub 2}O{sub 3}, C{sub 27}H{sub 46}O, and hard nylon materials. Besides, phantom also has a part to calculate low cost criteria /CNR (Contrast to Noise Ratio). Uniformity will be measured at water distillation medium located in a part of phantom scale contrast. Phantom will be imaged by using micro ct-sky scan 1173 high energy type, and then also can be quantified CT number to examine SkyScan 1173 performance in imaging low contrast density materials. Evaluation of CT number is done at technique configuration parameter using voltage of 30 kV, exposure 0.160 mAs, and camera resolution 560x560 pixel, the effect of image quality to reconstruction process is evaluated by varying image processing parameters in the form of beam hardening corrections with amount of 25%, 66% and100% with each smoothing level S10,S2 and S7. To obtain the better high quality image, the adjustment of beam hardening correction should be 66% and smoothing level reach maximal value at level 10.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

ORIGIN OF THE COSMIC-RAY SPECTRAL HARDENING

Recent data from ATIC, CREAM, and PAMELA indicate that the cosmic-ray energy spectra of protons and nuclei exhibit a remarkable hardening at energies above 100 GeV nucleon{sup -1}. We propose that the hardening is an interstellar propagation effect that originates from a spatial change of the cosmic-ray transport properties in different regions of the Galaxy. The key hypothesis is that the diffusion coefficient is not separable into energy and space variables as usually assumed. Under this scenario, we can reproduce the observational data well. Our model has several implications for cosmic-ray acceleration/propagation physics and can be tested by ongoing experiments such as the Alpha Magnetic Spectrometer or Fermi-LAT.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

On the constitutive stress-strain relationships and evaluation of the softening coefficient in work hardening mechanisms

The constitutive stress-strain relationships for structural alloys, such as additively manufactured Ti- 6Al-4V, are reconstructed by assessing the form and mechanism of work hardening relationships. The stress-strain relationships are best fit using both the Hollomon and Voce expressions wherein the Voce expression well-reproduces the later stage(s) of work hardening whereas the Hollomon relationship provides a better fit just beyond the proportional limit.

36 MATERIALS SCIENCE↗

Model for the Softening Factor within Stages of Work Hardening

A formulation for a dimensionless coefficient c b is derived that represents a scale of microstructural softening for alloys which follow Kocks-Mecking (K-M) work hardening behavior. The variation of the true plastic strain ε p between the proportional limit σ y and the strength σ u at the instability is determined using the Considère criterion. Parameterization of the model is limited to variables expressly measured within tensile experiments. Further development is now made for the softening factor c bi through the individual and sequential stages 3 and 4 of plastic deformation during K-M work hardening Q behavior. Application is shown for tensile test results of Ti-6Al-4V made by different additively manufactured (AM) processes. It is found that the variation in plastic strain as a function of c bi produces a continuous curve representative of the alloy system. The results of data analysis indicate that Θ o3 and c b3 increase, while Θ o4 and c b4 decrease, as the total plastic strain ε p increases. Furthermore, formulations derived for K-M stages 3 and 4 enable the evaluation of other material parameters such as the activation volume ν* for the onset of plastic deformation. This activation volume is found to be near constant, at a ν*-value of 0.353±0.036 nm 3 as computed using a strain-rate sensitivity of strength exponent m of 0.014, irrespective of the AM method used to produce the Ti-6Al-4V alloy.

36 MATERIALS SCIENCE↗

Electromechanical Hardening of VT22 Titanium Alloy in Screw-Cutting Lathes

The influence of electromechanical treatment on the hardening of VT22 titanium alloy is determined. The microstructure of the hardened surfaces is investigated, and the hardness is measured at different depths. Recommendations are made regarding the selection of electromechanical treatment methods.

36 MATERIALS SCIENCE↗

Influence of Diffusional Surface Alloying on the Hardened-Layer Thickness for Gray-Iron Machine Parts

In diffusional surface alloying, gray-iron components of vehicles and machines are heated in contact with oxides of the alloying elements (chromium, titanium, vanadium, and molybdenum). The influence of the sample temperature and holding time in diffusional surface alloying on the thickness of the hardened layer is investigated, on the basis of experiment planning. The models obtained may be used to ensure specified thickness of the hardened layer in diffusional surface alloying, with maximum productivity in both production and repair processes.

36 MATERIALS SCIENCE↗

Work Hardening Model of Structure in Hall-Petch Strengthening

The microstructural length scale of metals changes by orders of magnitude under extreme processing conditions producing a concurrent wide range of mechanical strength and plasticity behaviors. A unified stress-strain σε σ(ε) model is formulated that’s based on superposing the components of asymptotic-curvilinear work hardening Θσ Θ(σ) to qualify and quantify these mechanical behaviors. This approach accounts for the rapid strengthening of metals beyond the initial yield point, through extended steady-state deformation, to the structural instability. The relationship between the softening coefficients cbi c bi of the work hardening formulation Θσ Θ(σ) and strength are found to reveal the microstructural scale in the material. Specifically, the rapid decrease in the slope of the Θσ Θ(σ) curve provides a measure for microstructural size consistent with a functional Hall-Petch relationship of strength. A successful application is shown for the tensile behavior of pure aluminum microstructures that result from extreme plastic deformation by equal-channel angle pressing.

Hall-Petch strengthening↗

Irradiation hardening in F82H irradiated at 573 K in the HFIR

Post-irradiation tensile tests were conducted on alloy F82H and variants of this steels irradiated at 573 K up to 19 dpa in the High Flux Isotope Reactor (HFIR) in Oak Ridge National Laboratory. Post-irradiation tensile and hardness tests revealed that the strength of F82H steeply increased below 5 dpa, and the total elongation decreased. The ductility of the variants, which showed more ductility in the unirradiated condition was the same as irradiated F82H, even though the magnitude of irradiation hardening is smaller than F82H. This suggests that the softened parts of the blanket, such as heat affected zones, could show more ductility loss at this temperature. The hardening behavior of F82H with 0.09% additional tantalum (mod3), which demonstrated microstructural stability under high temperature processing, was very similar to that of F82H. Therefore mod3 can be an attractive alternate structural material for a blanket when processed above 1373 K.

36 MATERIALS SCIENCE↗

PV Storm Hardening Costs

While solar arrays often survive severe weather events, systems are occasionally compromised and left unable to provide power. For PV systems to act as resilient power providers, they must remain operational. Building a system that is more likely to survive a storm comes at a cost, though. Previous efforts have identified various system measures and practices that can increase the likelihood of a PV system surviving a severe weather event. But what is the cost premium for a storm hardened PV system? This report provides initial estimates for the up-front cost premiums for various methods of storm hardening PV systems.

14 SOLAR ENERGY↗

Thermal creep model for CWSR zircaloy-4 cladding taking into account the annealing of the irradiation hardening

After irradiation and cooling in a pool, spent nuclear fuel assemblies are either transported for wet storage to a devoted site or loaded in casks for dry storage. During dry transportation or at the beginning of dry storage, the cladding is expected to be submitted to creep deformation under the hoop stress induced by the internal pressure of the fuel rod. The thermal creep is a potential mechanism that might lead to cladding failure. A new creep model was developed, based on a database of creep tests on as-received and irradiated cold-worked stress-relieved Zircaloy-4 cladding in a wide range of temperatures (310 degrees C to 470 degrees C) and hoop stress (80 to 260 MPa). Based on three laws-a flow law, a strain-hardening recovery law, and an annealing of irradiation hardening law this model allows the simulation of not only the transient creep and the steady-state creep, but also the early creep acceleration observed on irradiated samples tested in severe conditions, which was not taken into account in the previous models. The extrapolation of the creep model in the conditions of very long-term creep tests is reassuring, proving the robustness of the chosen formalism. The creep model has been assessed in progressively decreasing stress conditions, more representative of a transport. Set up to predict the cladding creep behavior under variable temperature and stress conditions, this model can easily be implemented into codes in order to simulate the thermomechanical behavior of spent fuel rods in various scenarios of postirradiation phases. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗