Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fluidized bed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Advanced Syngas Cleanup Using Radically Engineered Modular Systems

The overall objective of this project was to address key knowledge gaps and develop modular sorbent-based warm syngas cleanup designs that will enable 1- to 5-MW REMS-based plants to be cost-competitive with large state-of-the-art commercial plants utilizing all of our abundant domestic coal reserves. We proposed to develop two potential new desulfurization process designs specifically targeted for REMS plants for combined heat and power or polygeneration from coal gasification. The first design is a modification of our commercially offered dual transport reactor design based Warm-gas Desulfurization Process (WDP) where the transport-reactor regenerator is replaced with a fluidized-bed regenerator. This design leverages the learnings obtained from our pre-commercial demonstration testing of the WDP technology for over 3,000 hours and conclusions from the lessons learned workshop. The second design is a fixed-bed process that leverages the successful composition and chemistry of our WDP sorbent to develop an effective fixed-bed sorbent formulation and fixed-bed process design. These two potential desulfurization process designs have a strong technical likelihood of success and offer the best opportunity to effectively employ design standardization, mass production and advanced manufacturing techniques to enable cost competitiveness for syngas cleanup at smaller scale.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Optimization of Hydrogen Production from Pyrolysis of Biomass Waste [Poster]

We developed an CFD aided ML-based tool for rapid assessment and optimization of different compositions of biomass in a fluidized bed reactor. First, we use CFD to simulate fluidized bed reactors with known inlet biomass mixtures and obtain corresponding syngas yields. A lumped kinetic mechanisms represents the conversion of cellulose, hemicellulose, and lignin, as well as subsequent cracking of tars into non-condensable gases (H 2 , CO, CO 2 , CH 4 ). We use Bayesian analysis/optimization to obtain the ideal operational and mass flow conditions for hydrogen production.

08 HYDROGEN↗
DOE OSTI2022

An index to characterize gas‐solid and solid‐solid mixing from average volume fraction fields

Abstract A mixing index based on solid volume fraction fields is developed for gas‐solid flows. Conventional mixing indices are based on particle realizations of granular mixing and are applicable to experimental data or discrete element method simulations. However, these indices cannot be used as‐is for multifluid models, and an index for characterizing mixing in gas‐solid flows from continuous fields is needed. The performance of the new mixing index is tested in two applications. The first is a 3D simulation of the mixing of biomass and sand in a fluidized bed reactor, and the second is a 2D simulation of binary particle segregation in a fluidized bed. The simulations are performed using OpenFOAM®. The mixing index is used to quantify gas‐solid mixing using solid volume fractions and solid‐solid mixing using solid fractions. The formulation of conventional mixing indices is extended to be used with solid volume fractions fields, and methods for performance improvement are presented.

09 BIOMASS FUELS↗
NASA NTRSDate not supplied

Parameters Impacting Columnated Granular Soil Pneumatic Seal Performance

The ability of a column of loose granular soil to form a pneumatic seal was investigated by varying the diameter of the soil column, the effective column height, and the level of compaction in the soil. The soil column diameter was tested at three levels using pipes with inner diameters measuring 5.08, 10.16, and 15.24 centimeters (2, 4, and 6 inches). Soil was filled in each pipe to form 15, 30, and 45 centimeter (6, 12, and 18 inch) tall soil columns. Each diameter/height configuration was also tested at three levels of soil compaction, compared by calculating the bulk density of the soil with mass and volume measurements. GRC-1a simulant was used, with approximate low/medium/high bulk densities of 1.6, 1.75, and 1.9 g/cc achieved with a combination of vibration and tamping. The order of tests for a given column diameter was randomized and repeated three times. With the top of the soil open to atmosphere at room temperature, compressed air was injected through a small diffuser at the column base with several small downward-facing holes. The number and size of these holes was scaled such that a constant total inlet orifice area to column cross sectional area ratio was maintained for each column diameter. Inlet air pressure was slowly increased via a precision regulator to preserve quasi-static equilibrium in the soil column to minimize the impact of dynamics. Air pressure was increased all the way through the static and bubbling regimes until slugging or turbulent behavior was observed in the soil to ensure that the entire static regime had been captured during data collection. A three-factor, three-level analysis of variance (ANOVA) statistical analysis was performed on the resulting data to determine the extent to which each physical parameter impacted the soil column seal performance. It was concluded that there is statistically significant evidence that column height, and the interaction between column height and diameter impact soil seal performance. In all other cases there was insufficient data to identify a statistically significant causal relationship. Additionally, plots were generated comparing experimental data to the predictive formula developed by Ogino et al. for fluidized beds in 1993. Because this model was developed for industrial spouted fluidized beds, the accuracy of its output prior to fluidization in the static seal ‘edge case’ is unknown, especially considering in this application the working gas was diffused across the column base rather than being injected through a spout. Further, the fidelity of the model had not yet been tested with lunar soil simulants. Plotting the Ogino et al. model alongside test data allows for a more intuitive sense of the impact of test parameters on soil seal performance, as well as providing a quick means to further tune this predictive model for more accurate use with static seals across granular lunar soil simulants. The model provided by Ogino et al. was further tuned using test data to determine the degree to which a spouted bed model could be applied to a slightly modified set of testing conditions: lunar soil simulants and a more diffuse, homogeneous application of pneumatic pressure. A Matlab script was created to test different values for the leading coefficient and exponents in Ogino’s formula. The script swept preset ranges, then iterated with higher resolutions across narrower ranges to converge on the optimal value for each parameter. The resulting adjusted model was compared to the original, as well as test data with noticeable improvements across the entire test domain.

Jack Stewart↗
NASA NTRS1987

Desulfurizing Coal With an Alkali Treatment

Experimental coal-desulfurization process uses alkalies and steam in fluidized-bed reactor. With highly volatile, high-sulfur bituminous coal, process removed 98 percent of pyritic sulfur and 47 percent of organic sulfur. Used in coal liquefaction and in production of clean solid fuels and synthetic liquid fuels. Nitrogen or steam flows through bed of coal in reactor. Alkalies react with sulfur, removing it from coal. Nitrogen flow fluidizes bed while heating or cooling; steam is fluidizing medium during reaction.

Ravindram, M.↗
DOE OSTI2026

Onset of Fluidization in MP-PIC Simulations using MFIX-Exa

Fluidized bed reactors are used across a variety of industries, including for energy processes like pyrolysis that result in low-cost energy products. Design and scale-up of fluidized beds is de-risked by modeling and simulation, utilizing tools like NETL’s MFIX-Exa High-Performance Computing (HPC) code for reacting multiphase flow. This report summarizes an investigation into the breadth of problems to which MFIX-Exa may be applied, specifically with regard to low fluid velocities and the onset of fluidization. A simple fluidization study is conducted both experimentally and numerically for particles of interest, then reactor simulations are compared to cold flow experiments for uniform distributor plates. Approaches for modeling bubble caps are also presented.

discrete particle method↗
DOE OSTI2022

Uranium Oxide Elutriation at Higher Flow Rates and Longer Times

This work supports the recovery of high-assay low-enriched uranium (i.e., U enriched in 235 U to >5% and <20%) from used nuclear fuel. One step includes elutriating triuranium octoxide (U 3 O 8 ) from a fluidized bed of alumina (Al 2 O 3 ) that fills the main reaction chamber. The experiments outlined in this report assessed the effects of the time and flow rate on the elutriation of U 3 O 8 powder from the reaction vessel. Testing at Oak Ridge National Laboratory (ORNL) was performed in a one-fourth scale experimental apparatus based on a pilot-scale system, which is the Material Recovery Pilot Plant (MRPP) at Idaho National Laboratory (INL). The experimental system comprises a supply of pressurized nitrogen (N 2 ), a gas heater, the reaction vessel, a knock-out pot, and a water trap where elutriated particles are collected for sampling. An Al 2 O 3 fluidized bed is contained within the reaction vessel. A bed of Al 2 O 3 with a nominal size of 180 µm and U 3 O 8 with a nominal size of 7 µm was fluidized at 2 different flow rates so the U 3 O 8 physically separated from the bed. The apparatus was simple and had no valves or sharp bends downstream from the reactor. The flow exited the reactor through a side port at the top. The flow passed through a knock-out vessel before the flow was passed through a bubbler to capture the U 3 O 8 . Seven tests were completed with U 3 O 8 using an elutriating gas of N 2 heated to 200°C. Tests were performed with bed loadings that comprise 25.0 g of U 3 O 8 , or 3.6 wt% of the bed mass. Except for one test performed at 12 SLPM, the gas flow rate through the bed for the other experiments was set at 10 SLPM as measured by the mass flow meter. Linear velocities through the bed were calculated as 28 and 34 cm/s, or 0.9 and 1.1 ft·s -1 . The duration of the tests ranged from 20 to 180 min, and one test had a flow cycled between 0 and 5 SLPM every 5 min for 40 min. The testing successfully demonstrated elutriation of U 3 O 8 from the fluidized bed as up to a 100% of the U 3 O 8 was transferred out of the bed. The removal of U 3 O 8 had a logarithmic dependence on flow rate. The design changes made the apparatus easier to clean, and the mass balances were better than those used in previous studies. Some elutriated Al 2 O 3 collected in the tubing that connected the reactor to the knock-out pot, but the amount of Al 2 O 3 was minimal for 10 SLPM. The flow at 12 SLPM showed considerable transport of Al 2 O 3 bed material into the reaction-vessel headspace and the transfer line to the knock-out pot.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

The role of biochar in the degradation of sugars during fast pyrolysis of biomass

With appropriate pretreatment, sugars can be a major product from fast pyrolysis of lignocellulosic biomass. Analytical pyrolysis of pure cellulose can produce up to 60 wt% yield of levoglucosan although yields are significantly lower in continuous pyrolysis at larger scales. Secondary reactions of vaporized levoglucosan are thought to be responsible for this loss of sugar yield, suggesting changes in the design and operation of pyrolysis reactors to minimize these reactions. Micropyrolysis experiments were performed to better understand the mechanism of sugar degradation in the presence of biochar. A 57% loss in levoglucosan yield was observed for cellulose overlain with untreated biochar powder compared to the pure cellulose control sample. The addition of biochar derived from pyrolysis of untreated corn stover to a fluidized bed pyrolyzer reduced sugar yields from cellulose from 61.3 wt% to 21.3 wt% and 41.5–11.6 wt% for conventional and autothermal operation, respectively. The significant drop in sugar yield due to biochar interaction inspired change in feeder configuration for the fluidized bed pyrolyzer to reduce vapor-char interactions. Biomass feeding was changed from in-bed to above-bed injection, which allowed significant devolatilization to occur above the layer of biochar that exists at the surface of the bed. Finally, by reducing secondary reactions, bio-oil and sugar yields increased by 7.9% and 14%, respectively, for autothermal pyrolysis.

09 BIOMASS FUELS↗
DOE OSTI2020

Analysis of hematite attrition in a grid jet apparatus

Particulate attrition is of interest for novel carbon-capture processes such as chemical looping combustion because the makeup cost of oxygen carrier is a significant portion of operating cost. As such, models to study and predict attrition of various oxygen carriers in fluidized bed systems are being developed. One of the regions of concern in fluidized bed systems is the high-velocity jet region near gas distributors in a fluid bed. This work studies the attrition of hematite particles using a modified ASTM apparatus to measure the particle size distribution throughout the experiment. Bed weight and gas velocity were varied. Hematite particles above the corresponding threshold value had a severe variation of particle size distributions which decreased with time. Weight fractions of the sieves over time were fit to a linear, time-variant population balance model to offer insight into particle attrition. The first-order rate constant was modified as a decaying exponential.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2010

Microwave Plasma Hydrogen Recovery System

A microwave plasma reactor was developed for the recovery of hydrogen contained within waste methane produced by Carbon Dioxide Reduction Assembly (CRA), which reclaims oxygen from CO2. Since half of the H2 reductant used by the CRA is lost as CH4, the ability to reclaim this valuable resource will simplify supply logistics for longterm manned missions. Microwave plasmas provide an extreme thermal environment within a very small and precisely controlled region of space, resulting in very high energy densities at low overall power, and thus can drive high-temperature reactions using equipment that is smaller, lighter, and less power-consuming than traditional fixed-bed and fluidized-bed catalytic reactors. The high energy density provides an economical means to conduct endothermic reactions that become thermodynamically favorable only at very high temperatures. Microwave plasma methods were developed for the effective recovery of H2 using two primary reaction schemes: (1) methane pyrolysis to H2 and solid-phase carbon, and (2) methane oligomerization to H2 and acetylene. While the carbon problem is substantially reduced using plasma methods, it is not completely eliminated. For this reason, advanced methods were developed to promote CH4 oligomerization, which recovers a maximum of 75 percent of the H2 content of methane in a single reactor pass, and virtually eliminates the carbon problem. These methods were embodied in a prototype H2 recovery system capable of sustained high-efficiency operation. NASA can incorporate the innovation into flight hardware systems for deployment in support of future long-duration exploration objectives such as a Space Station retrofit, Lunar outpost, Mars transit, or Mars base. The primary application will be for the recovery of hydrogen lost in the Sabatier process for CO2 reduction to produce water in Exploration Life Support systems. Secondarily, this process may also be used in conjunction with a Sabatier reactor employed to stockpile life-support oxygen as well as propellant and fuel production from Martian atmospheric CO2

Atwater, James↗
DOE OSTI2020

Oxidation kinetics of biochar from woody and herbaceous biomass

The goal of this study was to determine oxidation kinetics for biochar produced from fast pyrolysis of various biomass feedstocks. In particular, the role of inherent ash content on the oxidation rate was evaluated. Thermogravimetric analysis (TGA) and fluidized bed combustion experiments were used to explore oxidation kinetics of six fast pyrolysis produced biochars with diverse ash content. Here, the reaction rates varied by a factor of three under chemical kinetic-limited conditions, demonstrating inorganic content impacts oxidation rate. Chemical kinetic rate coefficients were proposed as a function of compositional parameters to determine overall fit and impact. Potassium content was found to have a positive correlation, best describing the differences in the oxidation kinetic rate coefficients. Additionally, feedstocks were subjected to a 1 M HCl acid wash mitigating the catalytic activity of the metals. Acid washed biochars had lower oxidation kinetic rates compared to their unwashed counterparts, indicating the removal of catalytically active metals reduced oxidation rate. Gas composition (CO/CO 2 ) was measured during fluidized bed experiments for both acid-washed and unwashed biochars, which varied between the six biochars. Formation of CO 2 was greatly affected by catalytic metals, finding potassium content to correlate well with a higher percentage of CO 2 formation as compared to CO. Comparison of oxidation rates were made between the two experimental apparatuses to measure the effect of attrition on biochar oxidation.

09 BIOMASS FUELS↗
DOE OSTI2026

Prototype Modeling for a Light-Trapping Planar-Cavity Enclosed Particle Solar Receiver

Concentrating solar thermal (CST) systems present a promising avenue for affordable and reliable energy production. Solar receivers are key components that determine the efficiency and longevity of these systems. Particle-based solar receivers have emerged as a compelling alternative to traditional technologies, offering several advantages that address limitations in current CST systems. This is especially true as next-generation CST technologies target applications including electricity generation, thermochemical processes, and industrial process heat, many of which necessitate higher operating temperatures than current commercial molten salt systems. Molten-salt thermal energy storage (TES) systems, commonly used in CSP, face challenges related to freezing and corrosion. Particle-based TES systems, in contrast, do not experience these issues, as particles are stable at high temperatures, exceeding 1000 degrees Celsius. This capability allows for a wider range of applications, including those requiring higher temperatures for industrial processes and efficient electricity generation. A novel innovation in particle-based solar receiver technology is the light-trapping planar cavity receiver (LTPCR) configuration developed by NREL. The LTPCR design consists of small cavity-like structures using opaque planar surfaces, enabling efficient capture and absorption of solar energy. A high incident flux concentration at the cavity aperture is absorbed on the receiver walls, and subsequently transferred to particles on the inside of cavities. The particles flow through the system, forming a fluidized bed inside of the receiver panels, effectively capturing the absorbed solar heat. Air is used as a fluidizing medium in this process to enhance particle heat transfer and mixing. The effectiveness of this design lies in its ability to manage solar flux conditions and ensure high solar-to-thermal receiver efficiency. A 100-kW prototype is currently being tested at the King Saud University in Saudi Arabia to assess the receiver performance. A range of modeling analyses for the optical, thermal, and mechanical effects were conducted to assess the performance of the receiver under on-sun conditions. The solar flux resulting from the KSU heliostat field was modeled using NREL SolTrace software and produced up to 600 kW/m2 at the receiver aperture. The solar flux absorbed on the receiver walls was then used within a computational fluid dynamics (CFD) model to predict wall temperature distributions along with radiation and convection loss. A two-phase CFD model was developed for the fluidized bed of silica sand inside the receiver panels to predict local wall-to-particle heat transfer coefficients, particle temperature distributions, and outlet temperature of the particles. We have also conducted analyses to understand the thermomechanical behavior of these innovative enclosed light-trapping solar receivers optimized for particle heating. We used finite element analysis (FEA) to predict the receiver's performance using temperature distributions obtained from CFD and based on the resulting stress profiles, evaluated creep-fatigue damage with a goal of achieving a 30-year service life. Analysis showed a significant impact of the particle-to-wall heat transfer coefficients (HTCs) on receiver performance, with higher HTCs resulting in reduced stress and increased lifespan. For instance, when using Inconel 740H, increasing the HTC from 800 W/m2 K to 1400 W/m2 K increased the creep life from 4,000 hours to over 100,000 hours. This highlights the importance of understanding and optimizing heat transfer in the design of high-efficiency receivers.

14 SOLAR ENERGY↗
NASA NTRS1978

Evaluation of selected chemical processes for production of low-cost silicon, phases 1 and 2

A miniplant, consisting of a 5 cm-diameter fluidized-bed reactor and associated equipment was used to study the deposition parameters, temperature, reactant composition, seed particle size, bed depth, reactant throughput, and methods of reactant introduction. It was confirmed that the permissible range of fluidized-bed temperature was limited at the lower end by zinc condensation (918 C) and at higher temperatures by rapidly decreasing conversion efficiency. Use of a graded bed temperature was shown to increase the conversion efficiency over that obtained in an isothermal bed. Other aspects of the process such as the condensation and fused-salt electrolysis of the ZnCl2 by-product for recycle of zinc and chlorine were studied to provide information required for design of a 50 MT/year experimental facility. In view of the favorable technical and economic indications obtained, it was recommended that construction and operation of the 50 MT/year experimental facility be implemented.

Blocher, J. M.↗
DOE OSTI2025

Modeling the Impacts of Hydrogen Extraction on Anaerobic Fermentation Systems Using a Modified ADM1 Model

Here, this paper presents a modified ADM1 (mADM1) model for use in assessing the influence of active dissolved H 2 extraction on biogas production from anaerobic fermentation reactors, specifically in the context of high-strength brewery wastewater as the feed. The modified model adds regulation factors to account for the varying product stoichiometry of glucose degradation reactions as a function of H 2 concentration in anaerobic digestion, and incorporates the use of both lactate and ethanol as intermediates. The changes to the model are expected to better predict the effects of H 2 removal on the production of H 2 in fermentation processes. Both ADM1 and mADM1 were calibrated against experimental data from a fluidized-bed reactor containing encapsulated acidogenic-acetogenic microbial communities treating real brewery wastewater. The calibrated models were validated against another fluidized-bed reactor identical to the calibration reactor, with the addition of a hollow-fiber membrane module that was used to reduce dissolved H 2 concentrations in the validation reactor. It was found that ADM1 over-estimated the H 2 production rates of the validation reactor (117 mL/day simulated vs. 16.48 mL/day experimental), whereas mADM1 was able to successfully predict fermentation, and specifically the H 2 production rate (17 mL/day). The presented model is a first step towards a model that can predict the effects of dissolved H 2 removal on fermentation processes.

Anaerobic Digestion↗
NASA NTRS1987

Preventing Cracks in Silicon-Reactor Liners

Correct placement helps prevent contamination while eliminating crack-causing deposits. Repositioning quartz liner in silicon fluidized-bed reactor prevents cracking of liner when cools. Liner protects stainless-steel walls of reactor from abrasion by particles in fluidized bed. Prevents contamination of newly formed silicon by material abraded from wall and ensures high-quality product.

Lutwack, R.↗
NASA NTRS1976

Steady-state heat transfer in transversely heated porous media with application to focused solar energy collectors

A fluid flowing in a porous medium heated transversely to the fluid flow is considered. This configuration is applicable to a focused solar energy collector for use in an electric power generating system. A fluidized bed can be regarded as a porous medium with special properties. The solutions presented are valid for describing the effectiveness of such a fluidized bed for collecting concentrated solar energy to heat the working fluid of a heat engine. Results indicate the advantage of high thermal conductivity in the transverse direction and high operating temperature of the porous medium.

Nichols, L. D.↗
NASA NTRS1976

Evaluation of selected chemical processes for production of low-cost silicon

Plant construction costs and manufacturing costs were estimated for the production of solar-grade silicon by the reduction of silicon tetrachloride in a fluidized bed of seed particles, and several modifications of the iodide process using either thermal decomposition on heated filaments (rods) or hydrogen reduction in a fluidized bed of seed particles. Energy consumption data for the zinc reduction process and each of the iodide process options are given and all appear to be acceptable from the standpoint of energy pay back. Information is presented on the experimental zinc reduction of SiCl4 and electrolytic recovery of zinc from ZnCl2. All of the experimental work performed thus far has supported the initial assumption as to technical feasibility of producing semiconductor silicon by the zinc reduction or iodide processes proposed. The results of a more thorough thermodynamic evaluation of the iodination of silicon oxide/carbon mixtures are presented which explain apparent inconsistencies in an earlier cursory examination of the system.

Blocher, J. M., Jr.↗
NASA NTRS2007

Sintering of Lunar and Simulant Glass

Most oxygen-extraction techniques are temperature-dependent, with higher temperatures resulting in higher oxygen yield. An example is hydrogen reduction, in which the optimum process temperature is 1050 C. However, glass-rich lunar soil begins to show the effects of sintering at temperatures of 900 C or lower. Sintering welds particles together due to viscous relaxation of the glass in the sample. One approach to avoid problems related to sintering, such as difficulty in removing waste material from the reactor, is to keep the soil in motion. One of several methods being studied to accomplish this is fluidized-bed processing techniques, in which the grains are kept in motion by the action of flowing reductant gas. The spent material can be removed from the chamber while still fluidized, or the fluidizing motion can continue until the material has cooled below approx. 500 C. Until end-to-end prototypes are built that can remove the heated soil, the most practical option is to keep the bed fluidized while cooling the waste material. As ISRU technology advances, another option will become valuable, which is to intentionally sinter the material to a great enough extent that it becomes a brick. The free iron in lunar soil is magnetic, and ferromagnetic bricks can be manipulated by robotic systems using electromagnetic end effectors. Finally, if an electromagnetic field is applied to the soil while the brick is being formed, the brick itself will become a magnet. This property can be used to create self-aligning bricks or other building materials that do not require fasteners. Although sintering creates a challenge for early lunar surface systems, knowledge gained during prototype development will be valuable for the advanced lunar outpost.

Cooper, Bonnie L.↗