Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FFT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Evaluating the grain-scale deformation behavior of a single-phase FCC high entropy alloy using synchrotron high energy diffraction microscopy

We report although the deformation behavior of high-entropy alloys (HEAs) has been extensively studied at the macroscale, many important properties have yet to be explored for these alloys at the microscale, thus hampering accurate prediction of damage and failure processes. Synchrotron high-energy diffraction microscopy (HEDM) and fast-Fourier transform-based crystal plasticity modeling was conducted to investigate the three-dimensional (3D) grain-resolved micromechanical response for approximately 1,900 constituent grains within a single-phase FCC HEA up to 1% applied strain. The evolution of grain-resolved elastic strains, lattice reorientations, and maximum resolved shear stresses (mRSS) were evaluated to quantify elastic, yield, and fully plastic behavior. Overall, the initial critical resolved shear stress (CRSS), determined via in situ HEDM and companion modeling, was found to be > 20% higher than estimated using the classical polycrystalline Taylor factor (M = 3.06). However, a descriptive parameter based on the average grain-resolved Taylor factor ($\overline{M}$) was found to show excellent agreement with plastic yielding behavior observed within HEDM datasets. Noticeable deviations in HEDM lattice reorientations compared to both EVP-FFT simulations and classical predictions for FCC polycrystals were discovered, highlighting the complexity in correlating local lattice reorientations, Taylor, and Schmid factors with plastic response for this material at the grain-scale. Therefore, it is anticipated that the overall trends and parameter identification of 3D grain-resolved properties in this study can serve as an important foundation for continued mesoscale investigation on both well-established and newly developed Cantor-like HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of twin growth mechanisms in precipitate hardened AZ91

Here, in this work, an elasto-viscoplastic fast-Fourier-transform (EVP-FFT) model with a dislocation-density (DD) based hardening law is employed to study the growth of a {10$\bar{1}$2} tensile twin that is blocked by basal-precipitates in precipitate-hardened AZ91 magnesium alloy. It is frequently reported that twin growth is hindered in precipitate-hardened Mg alloys; however, thick twin domains are often observed experimentally in these material systems. Detailed numerical investigation of deformation twinning starting from an early propagation stage, before twin growth, reveals that the stress fields that result from two sequentially propagated twins co-impinging on a precipitate relaxes the twin back stress locally and promotes twin growth at the twin-precipitate junction. Based on these findings, a two-step growth mechanism is proposed for twins arrested by precipitates. In the first step, the interaction of a twin tip with a precipitate develops a stress concentration on the other side of the precipitate, prompting the formation of a second twin. Subsequently, the back stresses associated with the first twin are relaxed by the formation of the second twin, allowing the first twin to grow at the twin-precipitate junction and eventually engulf the precipitate. This mechanism suggests that twin growth can be achieved locally with minimal additional external forces, explaining how relatively large twin domains can develop even in the presence of arrays of precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multi-modal characterization of the B2 phase in the Ta-Re binary system

The energy and transportation industries demand materials that retain their mechanical property at high temperatures. Refractory complex concentrated alloys (RCCAs) with a BCC + B2 microstructure offer a potential solution, where maintaining the high temperature mechanical properties can be achieved by precipitation strengthening. This depends on the B2 phase in RCCAs being thermodynamically stable with a high solvus temperature. Recently, we predicted the high temperature stability of the B2 structure in the Ta-Re binary system, using density functional theory. Here, in this study, we provide experimental evidence for the existence of this phase for the first time, using a Ta 65 Re 35 alloy. Despite Ta-Re binary phase diagrams predicting a single-phase BCC microstructure for Ta 65 Re 35 , we show that a high Z nanoscale secondary phase appears after heat treatment at 1550 °C and 1100 °C. Scanning transmission electron microscopy (STEM) revealed that this phase has a cubic structure and is equiatomic TaRe though B2 superlattice reflections were absent in fast Fourier transforms (FFT) and diffraction patterns (DPs). DP simulations indicate that the B2 TaRe superlattice reflections are up to two orders of magnitude weaker than their fundamental reflections, making their detection challenging via electron microscopy. Neutron diffraction confirmed the second phase had a B2 structure. This study identified a previously unobserved high temperature stable B2 phase in the Ta-Re system, enabling the development of new high temperature BCC + B2 RCCAs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Online data-enabled predictive control

We develop an online data-enabled predictive (ODeePC) control method for optimal control of unknown systems, building on the recently proposed DeePC (Coulson et al., 2019). Our proposed ODeePC method leverages a primal-dual algorithm with real-time measurement feedback to iteratively compute the corresponding real-time optimal control policy as system conditions change. The proposed ODeePC conceptual-wise resembles standard adaptive system identification and model predictive control (MPC), but it provides a new alternative for the standard methods. ODeePC is enabled by computationally efficient methods that exploit the special structure of the Hankel matrices in the context of DeePC with Fast Fourier Transform (FFT) and primal-dual algorithm We provide theoretical guarantees regarding the asymptotic behavior of ODeePC, and we demonstrate its performance through numerical examples.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Evaluation of nature and intensity of fire concrete spalling by frequency analysis of sound records

Highlights: • Original sound-based NDT method to assess the spalling form and intensity within the time of the test is proposed. • Frequency analysis of recorded sound provides a quantitative and qualitative assessment of concrete propensity to spalling. • Nature of fire concrete spalling can be categorized by a well-defined frequency value. • Waveform and spectrogram analysis delivers information on the exact number of spalling events within the performed test. The paper presents a new method for identifying the form and intensity of spalling using an analysis of the acoustic signal emitted by concrete. To assess the intensity and monitor the course of concrete spalling during fire exposure, the analysis of the recorded sound from the furnace chamber is used. The spalling intensity was determined based on signal amplitude analysis. Investigation of sound records showed that the character of spalling can be categorized by a well-defined frequency value. Based on the analysis of the Fast Fourier Transform (FFT) spectrum, the authors have distinguished the following phenomena that are the source of the signal by assigning the corresponding frequency of the sound wave vibration: explosive spalling, aggregate spalling and destructive spalling.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of non-uniform void distributions on the yielding of metals

High-throughput (several thousand) calculations have been carried out to investigate the yield behavior of porous materials with randomly distributed pores, porosity levels over four orders of magnitude and up to a hundred pores per simulation box. To this end, a Galerkin based fast Fourier transform (FFT) formulation was enhanced to deal with high phase contrast materials. In addition, GPU parallelization was employed in solving the governing equation for strain fluctuations using a Krylov iterative solver. Emphasis is laid on the conditions under which percolation of plastically non-deforming zones through the porous network emerge, a regime termed unhomogeneous yielding. By way of contrast, the regime where the plastic strain fluctuations (associated with the heterogeneous void-matrix aggregate) fall below the percolation threshold is defined as homogeneous yielding. Here, we find that nonuniform pore distributions only affect unhomogeneous yielding and have a universal softening effect. The extent of this distribution softening is analyzed as a function of porosity, cell size and number of realizations. Whether the uncovered universal distribution softening has direct implications on failure resistance of porous materials is discussed.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2024

A parallel and performance portable implementation of a full-field crystal plasticity model

We have developed a parallel implementation of an Elasto-Viscoplastic Fast Fourier Transform-based (EVPFFT) micromechanical solver to enable computationally efficient crystal plasticity modeling for polycrystalline materials. Our primary focus lies in achieving performance portability, allowing a single EVPFFT implementation to run optimally on various homogeneous architectures, including multi-core Central Processing Units (CPUs), as well as on heterogeneous computer architectures comprising multi-core CPUs and Graphics Processing Units (GPUs) from different vendors. To accomplish this goal, we have leveraged MATAR, a C++ software library that simplifies the creation and utilization of multidimensional dense or sparse matrix and array data structures. These data structures are designed to be portable across diverse architectures through the use of Kokkos, a performance-portable library. Additionally, we have employed the Message Passing Interface (MPI) to efficiently distribute the computational workload among processors. The heFFTe (Highly Efficient FFT for Exascale) library is used to facilitate the performance portability of the fast Fourier transforms (FFTs) computation. The computational performance of EVPFFT is evaluated and presented in terms of parallel scalability and simulation runtime on different high-performance computing (HPC) architectures. As a result, the utility of the developed framework to efficiently simulate the micro-mechanical fields in polycrystalline microstructures in engineering applications is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

GPU-enabled extreme-scale turbulence simulations: Fourier pseudo-spectral algorithms at the exascale using OpenMP offloading

Fourier pseudo-spectral methods for nonlinear partial differential equations are of wide interest in many areas of advanced computational science, including direct numerical simulation of three-dimensional (3-D) turbulence governed by the Navier-Stokes equations in fluid dynamics. This paper presents a new capability for simulating turbulence at a new record resolution up to 35 trillion grid points, on the world's first exascale computer, Frontier, comprising AMD MI250x GPUs with HPE's Slingshot interconnect and operated by the US Department of Energy's Oak Ridge Leadership Computing Facility (OLCF). Key programming strategies designed to take maximum advantage of the machine architecture involve performing almost all computations on the GPU which has the same memory capacity as the CPU, performing all-to-all communication among sets of parallel processes directly on the GPU, and targeting GPUs efficiently using OpenMP offloading for intensive number-crunching including 1-D Fast Fourier Transforms (FFT) performed using AMD ROCm library calls. With 99% of computing power on Frontier being on the GPU, leaving the CPU idle leads to a net performance gain via avoiding the overhead of data movement between host and device except when needed for some I/O purposes. Memory footprint including the size of communication buffers for MPI_ALLTOALL is managed carefully to maximize the largest problem size possible for a given node count. Detailed performance data including separate contributions from different categories of operations to the elapsed wall time per step are reported for five grid resolutions, from 2048 3 on a single node to 32768 3 on 4096 or 8192 nodes out of 9408 on the system. Both 1D and 2D domain decompositions which divide a 3D periodic domain into slabs and pencils respectively are implemented. The present code suite (labeled by the acronym GESTS, GPUs for Extreme Scale Turbulence Simulations) achieves a figure of merit (in grid points per second) exceeding goals set in the Center for Accelerated Application Readiness (CAAR) program for Frontier. The performance attained is highly favorable in both weak scaling and strong scaling, with notable departures only for 2048 3 where communication is entirely intra-node, and for 32768 3 , where a challenge due to small message sizes does arise. Communication performance is addressed further using a lightweight test code that performs all-to-all communication in a manner matching the full turbulence simulation code. Performance at large problem sizes is affected by both small message size due to high node counts as well as dragonfly network topology features on the machine, but is consistent with official expectations of sustained performance on Frontier. Overall, although not perfect, the scalability achieved at the extreme problem size of 32768 3 (and up to 8192 nodes — which corresponds to hardware rated at just under 1 exaflop/sec of theoretical peak computational performance) is arguably better than the scalability observed using prior state-of-the-art algorithms on Frontier's predecessor machine (Summit) at OLCF. New science results for the study of intermittency in turbulence enabled by this code and its extensions are to be reported separately in the near future.

3D fast Fourier transform↗
DOE OSTI2021

Effect of neighboring grain orientation on strain localization in slip bands in HCP materials

Particularly in plastically anisotropic crystals, such as hexagonal close packed (HCP) materials, plastic deformation is realized by slip acting in the small volumes within individual crystals. Here we extend a full field fast Fourier transform (FFT)-based elasto-viscoplastic formulation to simulate the development of a single slip band on either prismatic or basal planes spanning a crystal. Calculations of the strain and stress fields induced locally within the band and parent crystal, and ahead of the band/grain boundary junction in the neighboring crystal are analyzed as the slip band intensifies under increasing applied strain. We report a substantial influence of the crystallographic orientation of the nearest neighboring grain on the rate of slip band localization. Performing the analysis on two materials, CP-Ti and Mg, indicates that the strength of the material affects the rate of localization, with stronger materials tending to localize more easily. A slip band tip stress-based criterion is proposed for identifying the nearest neighbor orientations in which slip band transmission is possible and the likely slip system for which it occurs. This indicator is validated against experimental studies on commercially pure Ti, an Mg–Y alloy, and Ti–6Al–4V. Finally, we show that for low GB misorientations, the slip band is likely to transmit into another slip band of the same type in the neighbor grain, while for high GB misorientations, it is likely to transmit into one of a different type or to not transmit at all.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Role of grain boundary crystallography on void growth in FCC metals

The growth of an isolated spherical void at and near a grain boundary or a triple junction is studied by means of full-field crystal plasticity simulations with explicit representation of the void. To examine the fundamental aspects of void/grain boundary interactions in these cases, a three-dimensional large-strain elasto-viscoplastic fast-Fourier transform (LS-EVP-FFT) model with axisymmetric tensile periodic boundary conditions was developed. We employ this model to reveal the role of crystallography (grain orientations, grain boundary misorientation and inclination angle with respect to the largest component of the applied stress) and type of loading on void growth. It was found that grain orientation was the primary crystallographic feature governing void growth in strain-rate controlled simulations. For strains small enough to not significantly alter the local geometry, the overall growth of the void in bicrystal boundaries was not strongly affected by grain boundary inclination angle. The relative amount of void growth experienced within each grain in a bicrystal or tri-crystal was strongly dependent on the grain boundary inclination angle. We found a subset of orientations that exhibit faster void growth in bicrystal boundaries than inside the constituent single crystals. Last, we show that when placed primarily in one grain but near the grain boundary, void growth was similar to void growth when placed at the grain boundary. Furthermore, the growing void remained in the original grain and did not grow into the other grain, regardless of crystallographic character.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of crossed-twin structure formation in magnesium and magnesium alloys

In this work, the effect of alloying addition on the propensity for twin-twin interactions to transform into crossed-twin structures in magnesium alloys is investigated. A full-field elasto-viscoplastic fast Fourier transform (EVP-FFT) framework combined with a discrete twin model and dislocation density-based hardening law for slip strengths is used to calculate the micromechanical fields in the crystalline matrix around the interacting twins. AZ31 and MgLi alloys are selected along with pure Mg to study the influence of plastic anisotropy in connection with alloying elements. These alloys were selected since their plastic anisotropy measure, which is defined as the ratio between the critical resolved shear stress for pyramidal $\langle$c +a$\rangle$ and basal $\langle$a$\rangle$ slip modes, spanned a wide range. To quantify the role of twin thicknesses, we probe a range of impinging twin thicknesses while fixing the recipient twin thickness. The analysis reveals that: (i) the local driving stress for crossed twin structure formation generated from the interaction of the two twins is lower in a low plastically anisotropic material, like a MgLi alloy, than a high plastically anisotropic material like pure Mg and (ii) the critical impinging twin thickness needed to form the crossed twin structure in pure Mg, AZ31 and MgLi alloys is ~0.5, ~0.75 and ~1.5 times the recipient twin thickness. We propose a relationship between the tendency for crossed twin structure formation and the experimentally observed higher ductility in MgLi alloys compared to pure Mg. Finally, one key implication of the findings is that crossed- twin structure formation can be hindered and the ductility of magnesium alloy thereby improved by properly choosing alloying elements that lower the slip strength for pyramidal $\langle$c + a$\rangle$ slip.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An immersed interface method for the 2D vorticity-velocity Navier-Stokes equations with multiple bodies

We present an immersed interface method for the vorticity-velocity form of the 2D Navier Stokes equations that directly addresses challenges posed by nonconvex immersed bodies, multiply connected domains, and the calculation of force distributions on immersed surfaces. The immersed interface method is re-interpreted as a polynomial extrapolation of flow quantities and boundary conditions into the immersed solid bodies, reducing computational cost and enabling simulations with nonconvex bodies that could not be discretized with previous immersed interface methods. In the flow, the vorticity transport equation is discretized using a conservative finite difference scheme and explicit Runge-Kutta time integration. The velocity reconstruction problem is transformed to a scalar Poisson equation that is discretized with conservative finite differences, and solved using an FFT-accelerated iterative algorithm. The use of conservative differencing throughout leads to exact enforcement of a discrete Kelvin's theorem, allowing for simulations with multiply connected domains and outflow boundaries that have challenged other immersed interface vortex methods. We also explore novel methods for recovering time-dependent pressure distributions on immersed bodies within a vorticity-based method and present a novel control volume formulation for recovering aerodynamic moments from only the vorticity and velocity fields. The method achieves second order spatial accuracy and third order temporal accuracy, and is validated on a variety of 2D flows in internal and free-space domains.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Implementation of a Mesh refinement algorithm into the quasi-static PIC code QuickPIC

Plasma-based acceleration (PBA) has emerged as a promising candidate for the accelerator technology used to build a future linear collider and/or an advanced light source. In PBA, a trailing or witness particle beam is accelerated in the plasma wave wakefield (WF) created by a laser or particle beam driver. The WF is often nonlinear and involves the crossing of plasma particle trajectories in real space and thus particle-in-cell methods are used. The distance over which the drive beam evolves is several orders of magnitude larger than the wake wavelength. This large disparity in length scales is amenable to the quasi-static approach. Three-dimensional (3D), quasi-static (QS), particle-in-cell (PIC) codes, e.g., QuickPIC, have been shown to provide high fidelity simulation capability with 2-4 orders of magnitude speedup over 3D fully explicit PIC codes. In PBA, the witness beam needs to be matched to the focusing forces of the WF to reduce the emittance growth. In some linear collider designs, the matched spot size of the witness beam can be 2 to 3 orders of magnitude smaller than the spot size (and wavelength) of the wakefield. Such an additional disparity in length scales is ideal for mesh refinement where the WF within the witness beam is described on a finer mesh than the rest of the WF. A mesh refinement scheme is described that has been implemented into the 3D QS PIC code, QuickPIC. Very fine (high) resolution is used in a small spatial region that includes the witness beam and progressively coarser resolutions in the rest of the simulation domain. A fast multigrid Poisson solver has been implemented for the field solve on the refined meshes and a Fast Fourier Transform (FFT) based Poisson solver is used for the coarse mesh. The code has been parallelized with both MPI and OpenMP, and the parallel scalability has also been improved by using pipelining. A preliminary adaptive mesh refinement technique is described to optimize the computational time for simulations with an evolving witness beam size. Several test problems are used to verify that the mesh refinement algorithm provides accurate results. Additionally, the results are benchmarked against highly resolved simulations exhibiting near-azimuthal symmetry, performed using QPAD—a novel hybrid QS PIC code that uses a PIC description in the coordinates (r, ct – z) and a gridless description in the azimuthal angle, Φ.

Linear collider↗
DOE OSTI2022

Study of the interplay between lower-order and higher-order energetic strain-gradient effects in polycrystal plasticity

in this report strain-gradient (SG) plasticity refers to a class of non-local theories in which gradients of plastic slip determine the storage of geometrically necessary dislocations, introducing a length-scale dependence in the mechanical behavior of crystalline materials, which is otherwise lacking in local theories. In this work, we incorporate lower-order (LO) and higher-order energetic (HOE) strain-gradient effects into a crystal plasticity fast Fourier transform (FFT)-based formulation to investigate the interplay of the length scale that each strain-gradient term introduces at the microscale, and the mechanical properties that result at the macroscale. For an applicable range of length scales, we consider two systems: a 1-D two-phase face centered cubic (FCC) laminate and a 3-D FCC polycrystal, and two uniaxial deformation modes: monotonic tension and cyclic tension–compression. We show that increases in the individual LO and HOE length scales increase the hardening rate and strength of the material, respectively. When combined, the strong LO hardening is less pronounced than the effect alone due to the lowering of the gradients due to the HOE microstress. We demonstrate that the LO and HOE hardening manifest as “isotropic” (yield surface expansion) and “kinematic” (yield surface shift) effects, respectively, consistent with their theoretical origins. We show that in cyclic loading, the Bauschinger effect emerges in both local and non-local calculations and link its origins and severity to the behavior in the strain field, slip-system rates, and the HOE microforce.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fast GPU 3D diffeomorphic image registration

3D image registration is one of the most fundamental and computationally expensive operations in medical image analysis. Here, we present a mixed-precision, Gauss–Newton–Krylov solver for diffeomorphic registration of two images. Our work extends the publicly available CLAIRE library to GPU architectures. Despite the importance of image registration, only a few implementations of large deformation diffeomorphic registration packages support GPUs. Our contributions are new algorithms to significantly reduce the run time of the two main computational kernels in CLAIRE: calculation of derivatives and scattered-data interpolation. Additionally, we deploy (i) highly-optimized, mixed-precision GPU-kernels for the evaluation of scattered-data interpolation, (ii) replace Fast-Fourier-Transform (FFT)-based first-order derivatives with optimized 8th-order finite differences, and (iii) compare with state-of-the-art CPU and GPU implementations. As a highlight, we demonstrate that we can register clinical images in less than 6 s on a single NVIDIA Tesla V100. This amounts to over 20 speed-up over the current version of CLAIRE and over 30 speed-up over existing GPU implementations.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

A discrete integral transform for rapid spectral synthesis

Accurate synthetic spectra that rely on large Line-By-Line (LBL)-databases are used in a wide range of applications such as high temperature combustion, atmospheric re-entry, planetary surveillance and laboratory plasmas. Conventionally synthetic spectra are calculated by computing a lineshape for every spectral line in the database and adding those together, which may take multiple hours for large databases. In this paper we propose a new approach for spectral synthesis based on an integral transform: the synthetic spectrum is calculated as the integral over the product of a Voigt profile and a newly proposed three-dimensional “lineshape distribution function”, which is a function of spectral position and Gaussian- & Lorentzian width coordinates. A fast discrete version of this transform based on the Fast Fourier Transform (FFT) is proposed, which improves performance compared to the conventional approach by several orders of magnitude while maintaining accuracy. Strategies that minimize the discretization error are discussed. A Python implementation of the method is compared against state-of-the-art spectral code RADIS, and is since adopted as RADIS's default synthesis method. The synthesis of a benchmark CO2 spectrum consisting of 1.8 M spectral lines and 200k spectral points took only 3.1 s using the proposed method (1011 lines × spectral points/s), a factor ~300 improvement over the state-of-the-art, with the relative improvement generally increasing for higher number of lines and/or number of spectral points. Finally, an experimental GPU-implementation of the method was also benchmarked, which demonstrated another 2~3 orders performance increase, achieving up to 5 ∙ 10 14 lines × spectral points/s.

42 ENGINEERING↗
DOE OSTI2022

A systematic study and framework of fringe projection profilometry with improved measurement performance for in-situ LPBF process monitoring

Fringe Projection Profilometry (FPP) is a cost-effective and non-invasive technology that has been shown to measure finer features. Here, in this work, we developed an in-situ FPP method to measure the dynamic topography of powder bed and printed layer during Laser Powder Bed Fusion (LPBF) additive manufacturing (AM) process. A systematic study towards developing a comprehensive framework of LPBF-specific FPP is demonstrated to enhance and evaluate the performance of applying FPP for in-situ LPBF monitoring, including 1) a modified sensor model with localized correction; 2) improved phase unwrapping with FFT filtering 3) quantitative uncertainty analysis; and 4) experimental validation with ex-situ characterization. The developed LPBF-specific FPP system and methods are implemented on a commercial LPBF-AM machine, achieving better accuracy, more robustness, and increased field of view while maintaining sufficient measurement range and decent resolution, in contrast to literature methods. The established FPP framework will facilitate the development of closed-loop control strategies for advancing LPBF based AM.

42 ENGINEERING↗
DOE OSTI2021

The effects of free surfaces on deformation twinning in HCP metals

Deformation twinning is a predominant mode of plastic deformation for hexagonal close packed metals, like Mg and Ti. The heterogenous microstructure and the local stresses associated with twinning play a key role in their mechanical response and fracture. Surface analyses, like electron microscopy, are frequently employed to spatially map microstructure and micromechanical fields in order to study twinning behavior. However, these measurements are inherently influenced by the vicinity of the free surface. In this work, an elasto-visco-plastic fast-Fourier-transform (EVP-FFT) polycrystal modeling approach is employed to investigate the effects of free surfaces on twin development before and after loading. We compare calculated micromechanical fields on free surfaces with those calculated inside the bulk and, in some cases, experimental surface measurements. The results indicate that the creation of free surfaces can promote twin propagation and growth and can influence twin morphology by causing a twin lamella to become larger, more blunted and irregular. The structure along the twin boundaries are also affected, due to the higher driving stresses that extend prismatic-basal and basal-prismatic facets. Furthermore, free surfaces invoke different slip activities in the twin and the surrounding parent crystal by enhancing basal, prismatic and pyramidal slip in some localized regions, while reducing slip in others. We demonstrate that the simulated free-surface effects lead to better qualitative and quantitative agreement with experimental measurements from scanning electron microscopy and digital image correlation.

36 MATERIALS SCIENCE↗