Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Expectation Maximization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Pressure Effects on the Self-Extinguishment Limits of Aerospace Materials

The Orion Crew Exploration Vehicle Module (CM) is being designed to operate in an atmosphere of up to 30% oxygen at a pressure of 10.2 psia for lunar missions. Spacecraft materials selection is based on an upward flammability test conducted in a closed chamber under the worst expected conditions of pressure and oxygen concentration. Material flammability depends on both oxygen concentration and pressure but, since oxygen concentration is the primary driver, all materials are certified in the 30% oxygen, 10.2 psia environment. Extensive data exist from the Shuttle Program at this condition which used relatively the same test methodology as currently used in the Constellation Program. When the CM returns to Earth, a snorkel device will be activated after splashdown to provide outside air to the crew; however, for operational reasons, it is desirable to maximize the time the crew is able to breathe cabin air before the snorkel device is activated. To maximize this time, it has been proposed to raise the partial pressure of oxygen in the CM immediately before reentry while maintaining the total cabin pressure at 14.7 psia. In addition, it has been proposed to leak-test the Orion CM with ambient air at a maximum pressure of 17.3 psia. No data exist to assess how high the cabin oxygen concentration can be at 14.7 psia or 17.3 psia. One is to re-test a large number of materials at these pressures at a significant cost. However, since the maximum oxygen concentration (MOC) at which a material will self-extinguish has been determined for a variety of spacecraft materials as a function of pressure, a second alternative is to use existing data to estimate the MOC at 14.7 psia and 17.3 psia. This data will be examined in this paper and an analysis presented to determine the oxygen concentrations at the increased pressures that will result in self-extinguishment of a material. This analysis showed that the oxygen concentration for the Orion CM at 14.7 psia cannot be set higher than 25.6% without potentially invalidating the materials flammability certification in 30% oxygen at 10.2 psia for some materials. Materials certified under these conditions would still be self-extinguishing in ambient air at 17.3 psia. alternative

Hirsch, David B.↗
NASA NTRS2012

The Search for Habitable Worlds. 1. The Viability of a Starshade Mission

As part of NASA's mission to explore habitable planets orbiting nearby stars, this article explores the detection and characterization capabilities of a 4 m space telescope plus 50 m starshade located at the Earth-Sun L2 point, known as the New Worlds Observer (NWO). Our calculations include the true spectral types and distribution of stars on the sky, an iterative target selection protocol designed to maximize efficiency based on prior detections, and realistic mission constraints. We conduct simulated observing runs for a wide range in exozodiacal background levels (epsilon = 1-100 times the local zodi brightness) and overall prevalence of Earth-like terrestrial planets (eta(sub solar halo))0.1-1). We find that even without any return visits, the NWO baseline architecture (IWA = 65 mas, limiting FPB = 4 x 10(exp -11) can achieve a 95% probability of detecting and spectrally characterizing at least one habitable Earth-like planet and an expectation value of approximately 3 planets found, within the mission lifetime and delta V budgets, even in the worst-case scenario (eta(sub solar halo) = 0.1 and = epsilon = 100 zodis for every target). This achievement requires about 1 yr of integration time spread over the 5 yr mission, leaving the remainder of the telescope time for UV-NIR general astrophysics. Cost and technical feasibility considerations point to a "sweet spot" in starshade design near a 50 m starshade effective diameter. with 12 or 16 petals, at a distance of 70,000-100,000 km from the telescope.

Turnbull, Margaret C.↗
NASA NTRS2013

Investigation of the Leak Response of a Carbon-Fiber Laminate Loaded in Biaxial Tension

Designers of pressurized structures have been reluctant to use composite materials because of concerns over leakage. Biaxial stress states are expected to be the worst-case loading condition for allowing leakage to occur through microcracks. To investigate the leakage behavior under in-plane biaxial loading, a cruciform composite specimen was designed that would have a relatively large test section with a uniform 1:1 biaxial loading ratio. A 7.6-cm-square test section was desired for future investigations of the leakage response as a result of impact damage. Many iterations of the cruciform specimen were evaluated using finite element analysis to reduce stress concentrations and maximize the size of the uniform biaxial strain field. The final design allowed the specimen to go to relatively high biaxial strain levels without incurring damage away from the test section. The specimen was designed and manufactured using carbon/epoxy fabric with a four-ply-thick, quasi-isotropic, central test section. Initial validation and testing were performed on a specimen without impact damage. The specimen was tested to maximum biaxial strains of approximately 4500micro epsilon without apparent damage. A leak measurement system containing a pressurized cavity was clamped to the test section and used to measure the flow rate through the specimen. The leakage behavior of the specimen was investigated for pressure differences up to 172 kPa

Jackson, Wade C.↗
NASA NTRSDate not supplied

Progress of 2.05 uM Fiber Laser Development for A Martian Co2 Dial

We have proposed a new concept for differential absorption lidar (DIAL) operating in the 2050 nm CO 2 absorption band for atmospheric CO 2 and pressure observations on Mars. This concept has earned us funding from NASA's PICASSO Program to advance 2050 nm fiber laser technology for future space applications. The laser design is an all-fiber master oscillator and power amplifier (MOPA) system. The master oscillator with pulse shaping and several stages of fiber preamplifiers has been built. Preliminary tests show the output pulse energy can reach 1 mJ, meeting our baseline goal. However, the current power amplifier design has an issue with undesired parasitic lasing at a different frequency, which exhausts pump energy and limits the laser energy. We have modified the power amplifier design to suppress parasitic lasing, and higher laser power energy is expected. To achieve high measurement accuracy, the laser frequency must be stabilized. A fraction of the master oscillator is split to lock the laser frequency to the center of the selected absorption line. The laser can then be shifted to a frequency far from the absorption line center, where extinction due to CO 2 and other trace gases is minimal, serving as the offline reference. The online wavelength is optimized at 2050.44156 nm, ensuring a CO 2 absorption optical depth (AOD) of approximately 1.1 at 3 km, which maximizes the signal-to-noise ratio (SNR) for measurements in the lower Martian atmosphere. At the conference, we will provide more details about this project and report on the progress of instrument development.

DIAL↗
NASA NTRS1988

Pulmonary function in microgravity: Spacelab 4 and beyond

This paper refers principally to the composition gradient of gases within the lung in various conditions of gravity, as revealed by exhaled breath. A rapid gas analyzer-based system has been developed for tests in Spacelab 4. The test sequence and expected results are presented.

Flight Experiment↗
NASA NTRS1994

Numerical comparison of convective heat transfer augmentation devices used in cooling channels of hypersonic vehicles

Hypersonic vehicles are exposed to extreme thermal conditions compared to subsonic aircraft; therefore, some level of thermal management is required to protect the materials used. Normally, hypersonic vehicles experience the highest temperatures in the nozzle throat, and aircraft and propulsion system leading edges. Convective heat transfer augmentation techniques can be used in the thermal management system to increase heat transfer of the cooling channels in those areas. The techniques studied in this report are pin-fin, offset-fin, ribbed and straight roughened channel. A smooth straight channel is used as the baseline for comparing the techniques. SINDA '85, a lumped parameter finite difference thermal analyzer, is used to model the channels. Subroutines are added to model the fluid flow assuming steady one dimensional compressible flow with heat addition and friction. Correlations for convective heat transfer and friction are used in conjunction with the fluid flow analysis mentioned. As expected, the pin-fin arrangement has the highest heat transfer coefficient and the largest pressure drop. All the other devices fall in between the pin-fin and smooth straight channel. The selection of the best heat augmentation method depends on the design requirements. A good approach may be a channel using a combination of the techniques. For instance, several rows of pin-fins may be located at the region of highest heat flux, surrounded by some of the other techniques. Thus, the heat transfer coefficient is maximized at the region of highest heat flux while the pressure drop is not excessive.

Maldonado, Jaime J.↗
NASA NTRS2003

Experimental Study of the Angle of Repose of Surrogate Martian Dust

Accumulation of wind-blown dust particles on solar cells and instruments will be a great challenge in the exploration of Mars, significantly reducing their lifetime, durability, and power output. For future Mars Lander missions it is crucial to gain information about the ideal angle at which solar panels can be positioned to minimize dust deposition and thus, maximize the power output and lifetime of the solar cells. The major determinant for the optimal panel angle is the angle of repose of the dust particles that is dependent on a variety of physical and chemical properties of the particles, the panel surface, and the environmental conditions on the Mars surface. To gain a basic understanding of the physical and chemical processes that govern dust deposition and to get feedback for the design of an experiment suitable for one of the future Mars Lander missions we simulate atmospheric conditions expected on the Mars surface in a controlled chamber, and observe the angle of repose of Mars dust surrogates. Dust deposition and angle of repose were observed on different sized spheres. To cover a range of potential materials we will use spheres made of 7075 aluminum (10 mm, and 15 mm), alumina oxide ceramic (10 mm), and Teflon(trademark) (10 mm) and wafers of gallium arsenide, silicon.

Moeller, L. E.↗
NASA NTRS2021

Extending the Licklider Transmission Protocol to Multi-Band Links

Most deep space missions return data to Earth using links operating at a single frequency band. Indeed, their data requirements are low enough that bandwidth regulations do not constrain the system. In contrast, spacecraft such as Kepler or Europa Clipper are transitioning to a new operational paradigm where engineering and science data are transmitted through simultaneous links operating at different frequency bands (henceforth termed multi-band links). This ensures, for instance, that critical data is correctly received using a well characterized X-band link, while science data at a much larger data rate can be returned efficiently (both in terms of bandwidth and energy) through a Ka-band link.Having a spacecraft establish two simultaneous links with a ground station opens a large span of potential improvements for space communications and mission operations. In this paper, we consider the problem of running a Licklider Transmission Protocol (LTP) session over a multi-band link. LTP is an implementation of a selective Automatic Repeat reQuest (ARQ) protocol, i.e. it ensures correct delivery of data over an error prone link with potentially long propagation delays. To maximize its efficiency in deep space environments, LTP operates in deferred-ACK mode and is typically included as one of the core protocols in the Delay Tolerant Networking (DTN) suite.The contributions of this paper are as follows: First, we propose an extension to LTP for multi-band links (denoted MBLTP) and sketch how it can be implemented without modifying the current definition of LTP data units. Next, we develop bounds on the performance of MBLTP when transmitting a single data file over a multi-band link. Three metrics are considered, file expected delivery time, total energy spent and bundle jitter. The results of the analytic model are first benchmarked against simulations to ensure validity, and then compared against the performance of both traditional LTP and Parallel LTP (PLTP).We demonstrate that MBLTP can significantly reduce the latency and jitter with which data products are delivered to destination over a deep space link compared to LTP at moderate energy cost. Similarly, we also demonstrate that MBLTP outperforms PLTP in all considered metrics.

Sanchez Net, Marc↗
NASA NTRS1988

Nucleate pool boiling: High gravity to reduced gravity; liquid metals to cryogens

Requirements for the proper functioning of equipment and personnel in reduced gravity associated with space platforms and future space station modules introduce unique problems in temperature control; power generation; energy dissipation; the storage, transfer, control and conditioning of fluids; and liquid-vapor separation. The phase change of boiling is significant in all of these. Although both pool and flow boiling would be involved, research results to date include only pool boiling because buoyancy effects are maximized for this case. The effective application of forced convection boiling heat transfer in the microgravity of space will require a well grounded and cogent understanding of the mechanisms involved. Experimental results are presented for pool boiling from a single geometrical configuration, a flat surface, covering a wide range of body forces from a/g = 20 to 1 to a/g = 0 to -1 for a cryogenic liquid, and from a/g = 20 to 1 for water and a liquid metal. Similarities in behavior are noted for these three fluids at the higher gravity levels, and may reasonably be expected to continue at reduced gravity levels.

Merte, Herman, Jr.↗
NASA NTRS2020

Mitigating Fading in Cislunar Communications: Application to the Human Landing System

NASA’s human exploration program is currently working towards landing astronauts on the surface of the Moon by 2024, close the lunar South Pole. To guarantee astronaut safety and maximize science data return, NASA is in the process of defining the communication architecture that will support all astronaut activities from launch to surface operations. Of particular interest to this paper are links from the lunar surface back to Earth without any intermediate relays. We show that the system geometry is such that antennas on the landing system will need to be pointed at low elevation angles, thus potentially causing multi-path fading effects not typically encountered in space communications. This paper is organized in three parts. First, we characterize the multi-path fading effects expected in links between the lunar South Pole and Earth and show that for moderate data rates (less than 1 Mbps) the links suffer from slow fading. We then show that for this operations regime the performance of forward error correction schemes is significantly worse for traditional Additive White Gaussian Noise channels. Finally, we investigate multi-copy mechanisms to mitigate the effects of fading, most notably repetition schemes and Automatic Repeat Request.

Sanchez Net, Marc↗
NASA NTRS2019

Development of the WFIRST CGI Integral Field Spectrograph

Future mission concepts such as LUVOIR and HabEx have baselined integral field spectrographs (IFS) for their coronagraph instruments. Exoplanet detection with an IFS has strong heritage at ground observatories, but to support future missions the WFIRST coronagraph instrument (CGI) must demonstrate the ability to measure exoplanet spectra with an IFS approaching contrast levels sufficient for future missions. The spectral resolution of the CGI IFS is R50 over a 20% bandpass within 600 and 970 nm. The bands and spectral resolution optimize signal-to-noise against sufficient sampling of methane absorption features expected in the exoplanet atmosphere. In addition to demonstrating on-orbit high contrast with the IFS, showing sufficient stability over very long observing periods with time resolved data in simultaneous spatial and spectral dimensions is key to the IFS demonstration. We present the impact of long durations and tight tolerances, how they drive the IFS design and performance.

Groff, Tyler D.↗
NASA NTRS2001

ISS Microgravity Research Payload Training Methodology

The NASA Microgravity Research Discipline has multiple categories of science payloads that are being planned and currently under development to operate on various ISS on-orbit increments. The current program includes six subdisciplines; Materials Science, Fluids Physics, Combustion Science, Fundamental Physics, Cellular Biology and Macromolecular Biotechnology. All of these experiment payloads will require the astronaut various degrees of crew interaction and science observation. With the current programs planning to build various facility class science racks, the crew will need to be trained on basic core operations as well as science background. In addition, many disciplines will use the Express Rack and the Microgravity Science Glovebox (MSG) to utilize the accommodations provided by these facilities for smaller and less complex type hardware. The Microgravity disciplines will be responsible to have a training program designed to maximize the experiment and hardware throughput as well as being prepared for various contingencies both with anomalies as well as unexpected experiment observations. The crewmembers will need various levels of training from simple tasks as power on and activate to extensive training on hardware mode change out to observing the cell growth of various types of tissue cultures. Sample replacement will be required for furnaces and combustion type modules. The Fundamental Physics program will need crew EVA support to provide module change out of experiment. Training will take place various research centers and hardware development locations. It is expected that onboard training through various methods and video/digital technology as well as limited telecommunication interaction. Since hardware will be designed to operate from a few weeks to multiple research increments, flexibility must be planned in the training approach and procedure skills to optimize the output as well as the equipment maintainability. Early increment lessons learned will be addressed.

Schlagheck, Ronald↗
NASA NTRSDate not supplied

Space Suit Portable Life Support System Fastener and Insert Summary, Issues, and Testing Results

Fasteners are included in every assembly on the Exploration External Mobility Unity Portable Life Support System (xEMU PLSS). However, fasteners and inserts have been the cause of many issues seen on the PLSS during development; furthermore, inserts with thermoplastics are not very well understood. The materials used in the PLSS are sometimes softer and lighter weight metals or thermoplastics which require the installation of inserts to improve the interface strength. In addition, space flight requirements call out the need for an additional running/locking torque, so they do not detach in case of failure of the final torque. The xEMU PLSS has experienced various issues with fasteners and inserts, from the bolt binding in an insert or the running torque failing prematurely. A study has been completed to address the running torque life problem. This study compares the insert and locking feature combinations to determine the combination which maximizes life. The study found that using a locking patch with an insert fails after the first installation. Therefore, it is no longer recommended to use a locking patch fastener with an insert for future installments. For the bolt binding issue, inserts have been installed too deep and have caused the bolt to bind near the final threads of the inserts where the hole is not tapped deep enough. Thermoplastics, on the other end, can either use standard helical inserts or heat set inserts. Another study was performed using tangless inserts and heat inserts installed in thermoplastics to quantify the expected pull-out strength for various insert installation parameters (insert type, temperature, and pressure). This paper will review the issues and lessons learned with fasteners on the xEMU PLSS, provide results of a locking feature study, and provide results and recommended installation settings from a heat insert study.

Ryan Ogilvie↗
NASA NTRS2024

Effect of Varying HUT Sizing on Human-Spacesuit Contact Patterns

Fit, comfort, and mobility of the spacesuit rely on the location, magnitude, and type of contact between the suit and wearer. Typically, spacesuits include the Hard Upper Torso (HUT) comprising the upper torso of the spacesuit. Potential injuries from hard contact between the wearer’s shoulders and the HUT are a concern; therefore, to investigate spacesuit-wearer contact patterns, data from a retrospective study was analyzed. This study had eight subjects wearing the Shuttle Extravehicular Mobility Unit (EMU) spacesuit in two configurations, one with a nominally sized HUT and another with an oversized HUT. The subjects were sized per the NASA standard suit fit procedure. The suit’s arms and lower body were also resized to provide nominal arm and lower body fit, accounting for the larger HUT. Subjects held various shoulder postures (neutral posture, and various maximum shoulder rotations) with the suit pressurized to 4.3 PSI. For each posture, subjects reported the intensity of their perceived contact with the suit on a Borg CR10 scale, 0 indicating a non-existent contact intensity, and 10 representing a maximal contact intensity. Ratings were recorded for 11 regions covering the upper body and these ratings were used to determine the impact of body shape and size on suit contact. Our preliminary findings suggest that oversized HUTs had less contact regions than compared to the nominal HUT; and the region of contact, contact patterns, and contact intensities varied from person to person with the oversized HUT. This variance could be linked to subjects’ body shape and size. The next goal is to establish a causal factor between body shape and size, pose, contact region, and the HUT size. The outcome is expected to help understand the overall contact trends and insights into the influence of HUT sizing on suit fit.

Will Green↗
NASA NTRS2013

Exploration of Near-Earth Asteroids

A major goal for NASA's human spaceflight program is to send astronauts to near-Earth asteroids (NEAs) in the coming decades. Missions to NEAs would undoubtedly provide a great deal of technical and engineering data on spacecraft operations for future human space exploration while conducting in-depth scientific examinations of these primitive objects. However, prior to sending human explorers to NEAs, robotic investigations of these bodies would be required in order to maximize operational efficiency and reduce mission risk. These precursor missions to NEAs would fill crucial strategic knowledge gaps concerning their physical characteristics that are relevant for human exploration of these relatively unknown destinations. Information obtained from a human investigation of a NEA, together with ground-based observations and prior spacecraft investigations of asteroids and comets, will also provide a real measure of ground truth to data obtained from terrestrial meteorite collections. Major advances in the areas of geochemistry, impact history, thermal history, isotope analyses, mineralogy, space weathering, formation ages, thermal inertias, volatile content, source regions, solar system formation, etc. can be expected from human NEA missions. Samples directly returned from a primitive body would lead to the same kind of breakthroughs for understanding NEAs that the Apollo samples provided for understanding the Earth-Moon system and its formation history. In addition, robotic precursor and human exploration missions to NEAs would allow the NASA and its international partners to gain operational experience in performing complex tasks (e.g., sample collection, deployment of payloads, retrieval of payloads, etc.) with crew, robots, and spacecraft under microgravity conditions at or near the surface of a small body. This would provide an important synergy between the worldwide Science and Exploration communities, which will be crucial for development of future international deep space exploration architectures and has potential benefits for future exploration of other destinations beyond low-Earth orbit.

Abell, Paul↗
NASA NTRS1997

Resistance exercise training and the orthostatic response

Resistance exercise has been suggested to increase blood volume, increase the sensitivity of the carotid baroreceptor cardiac reflex response (BARO), and decrease leg compliance, all factors that are expected to improve orthostatic tolerance. To further test these hypotheses, cardiovascular responses to standing and to pre-syncopal limited lower body negative pressure (LBNP) were measured in two groups of sedentary men before and after a 12-week period of either exercise (n = 10) or no exercise (control, n = 9). Resistance exercise training consisted of nine isotonic exercises, four sets of each, 3 days per week, stressing all major muscle groups. After exercise training, leg muscle volumes increased (P < 0.05) by 4-14%, lean body mass increased (P = 0.00) by 2.0 (0.5) kg, leg compliance and BARO were not significantly altered, and the maximal LBNP tolerated without pre-syncope was not significantly different. Supine resting heart rate was reduced (P = 0.03) without attenuating the heart rate or blood pressure responses during the stand test or LBNP. Also, blood volume (125I and 51Cr) and red cell mass were increased (P < 0.02) by 2.8% and 3.9%, respectively. These findings indicate that intense resistance exercise increases blood volume but does not consistently improve orthostatic tolerance.

NASA Discipline Musculoskeletal↗
NASA NTRS2009

Austere Human Missions to Mars

The Design Reference Architecture 5 (DRA 5) is the most recent concept developed by NASA to send humans to Mars in the 2030 time frame using Constellation Program elements. DRA 5 is optimized to meet a specific set of requirements that would provide for a robust exploration program to deliver a new six-person crew at each biennial Mars opportunity and provide for power and infrastructure to maintain a highly capable continuing human presence on Mars. This paper examines an alternate architecture that is scaled back from DRA 5 and might offer lower development cost, lower flight cost, and lower development risk. It is recognized that a mission set using this approach would not meet all the current Constellation Mars mission requirements; however, this 'austere' architecture may represent a minimum mission set that would be acceptable from a science and exploration standpoint. The austere approach is driven by a philosophy of minimizing high risk or high cost technology development and maximizing development and production commonality in order to achieve a program that could be sustained in a flat-funded budget environment. Key features that would enable a lower technology implementation are as follows: using a blunt-body entry vehicle having no deployable decelerators, utilizing aerobraking rather than aerocapture for placing the crewed element into low Mars orbit, avoiding the use of liquid hydrogen with its low temperature and large volume issues, using standard bipropellant propulsion for the landers and ascent vehicle, and using radioisotope surface power systems rather than a nuclear reactor or large area deployable solar arrays. Flat funding within the expected NASA budget for a sustained program could be facilitated by alternating cargo and crew launches for the biennial Mars opportunities. This would result in two assembled vehicles leaving Earth orbit for Mars per Mars opportunity. The first opportunity would send two cargo landers to the Mars surface to preposition a habitat, supplies, and exploration equipment. The next opportunity, two years later, would send to Mars orbit 1) a lander with a Mars Ascent Vehicle (MAV) and 2) a crewed Mars Transit Habitat with an Orion CEV for Earth return. The following opportunity, two years after the first crew, would go back to cargo-only launches. This alternation of cargo and crew opportunities results in a sustainable launch rate of six Ares V launches every two years. It is notable that four of the six launches per Mars opportunity are identical, build-to-print, Tran-Mars Injection stages. This type of production rate could lend itself well to a COTStype service provider, and would make it feasible to have a live spare in place in the event of a single launch failure.

landers↗
NASA NTRS2004

The Use of Pristine and Intercalated Graphite Fiber Composites as Buss Bars in Lead-Acid Batteries

This study was conducted as a part of the Firefly Energy Space Act Agreement project to investigate the possible use of composite materials in lead acid batteries. Specifically, it examined the use of intercalated graphite composites as buss bars. Currently, buss bars of these batteries are made of lead, a material that is problematic for several reasons. Over time, the lead is subject to both corrosion at the positive plate and sulfation at the negative plate, resulting in decreased battery life. In addition, the weight and size of the lead buss bars make for a heavy and cumbersome battery that is undesirable. Functionality and practicality of lead buss bars is adequate at best; consequently, investigation of more efficient composite materials would be advantageous. Practically speaking, graphite composites have a low density that is nearly one fourth that of its lead counterpart. A battery made of less dense materials would be more attractive to the consumer and the producer because it would be light and convenient. More importantly, low weight would be especially beneficial because it would result in greater overall power density of the battery. In addition to power density, use of graphite composite materials can also increase the life of the battery. From a functional standpoint, corrosion and sulfation at the positive and negative plates are major obstacles when considering how to extend battery life. Neither of these reactions are a factor when graphite composites replace lead parts because graphite is chemically non-reactive with the electrolyte within the battery. Without the problem of corrosion or sulfation, battery life expectancy can be almost doubled. The replacement of lead battery parts with composite materials is also more environmentally favorable because of easy disposal of organic materials. For this study, both pristine and bromine intercalated single-ply graphite fiber composites were created. The composites were fabricated in such a way as to facilitate their use in a 3" x 1/2" buss bar test cell. The prime objective of this investigation was to examine the effectiveness of a variety of graphite composite materials to act as buss bars and carry the current to and from the positive and negative battery plates. This energy transfer can be maximized by use of materials with high conductivity to minimize the buss resistance. Electrical conductivity of composites was measured using both a contactless eddy current probe and a four point measurement. In addition, the stability of these materials at battery-use conditions was characterized.

Opaluch, Amanda M.↗