Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electrical components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Tesla Valve Integration into Propulsion Systems for Water Hammer Mitigation

Water hammer is a pressure surge or wave caused when a liquid in motion is forced to stop or change direction suddenly. Satellite and in-space propulsion systems exhibit this effect when valves, which can pulse several times per second, close quickly to isolate propellant from thrusters. The inherent nature of pulsing thrusters quickly has made water hammer a constant design challenge for these systems. Historically, the standard is to accept that the Maximum Design Pressure (MDP) of the system must account for a full worst case water-hammer event, which can be several times the Maximum Expected Operating Pressure (MEOP). An investigation is being conducted to determine the effectiveness of tesla valves in reducing water hammer amplitudes. Tesla Valves can be used in-line within propulsion systems to allow unrestricted flow in one direction and restricted flow in the opposite direction without the use of added mechanical or electrical components. Tesla valves use fixed internal geometry to allow for this unrestricted and restricted flow. With the increase and capability of Additive Manufacturing (AM), different configurations and concepts of tesla valves can be manufactured and tested at minimal cost. This concept could possibly be used to allow for a less complicated, or robust satellite and in-space propulsion system. This presentation will cover topics of additive manufactured design of tesla valves, testing, and variables to consider within tesla valve creation.

Michael A Willis↗
NASA NTRSDate not supplied

Solid-State Exergy Optimized Electric Aircraft Thermal and Fault Management

Future air vehicles will increasingly incorporate electrical powertrains that require very tight system level integration of power, propulsion, thermal, fault protection, and airframe technologies. This paper provides an overview of a new category of thermal energy conversion technology that can be used to enable a fully solid-state integrated thermal and fault management electric aircraft protection system, while synergistically managing and recycling both the low-grade waste heat from electrical components and the high-grade waste heat from engine components. This is achieved with exergy amplification of the powertrain waste-heat, a new class of fast flight-weight breakers, new class of long variable conductance heat pipe with multiple switchable condensers, new class of turbofan integrated heat exchangers and a gradient-based powertrain system optimizer.

safety↗
NASA NTRS2020

Electric Aircraft Cooling with Bio-Inspired Exergy Management

Future air vehicles will increasingly incorporate electrical powertrains that require very tight system-level integration of power, propulsion, thermal, fault protection, and airframe technologies. This chapter provides an overview of a new category of thermal energy conversion technology and describes the development of the resulting Thermal Recovery Exergy Efficient System, TREES. TREES can be used to enable a fully solid-state integrated thermal and fault management electric aircraft protection system, while synergistically managing and recycling both the low-grade waste heat from electrical components and the high-grade waste heat from engine components. This is achieved with exergy amplification of the powertrain waste heat, a new class of fast flight-weight breakers, a new class of long variable-conductance heat pipes with multiple switchable condensers, a new class of turbofan-integrated heat exchangers, and a gradient-based powertrain system optimizer. This approach is like the human body’s thermal management system in which the heart, arteries, and veins are analogous to the turbofan, acoustic tubes, and heat pipes proposed herein.

Rodger W Dyson↗
NASA NTRSDate not supplied

Computational Evaluation of an OML-based Heat Exchanger Concept for HEATheR

Feasibility of outer mold line (OML) heat exchangers for electrified aircraft is computationally explored for three different aircraft concepts within The High-efficiency Electrified Aircraft Thermal Research (HEATheR) project. OML surface temperature limits were selected based on aluminum-alloy and carbon-fiber composite materials commonly used in transport aircraft. Heat flux distribution over the aircraft OML at the surface temperature limit was evaluated with computational fluid dynamics (CFD) analysis. The candidate OML locations and the size for the implementation of the OML-based heat exchanger is down-selected using this initial analysis and other considerations including the concern for structural integrity and proximity to heat-generating electrical components. The sensitivity of the heat transfer analysis to the computational grid, aircraft angle of attack, surface temperature, and the interaction of individual OML heat exchanger patches were investigated.

CAS↗
NASA NTRS2022

Updated Assessment of Turboelectric Boundary Layer Ingestion Propulsion Applied to a Single-Aisle Commercial Transport

Recent advances in technology and a push for more environmentally friendly air transportation has led to interest in electrified aircraft propulsion (EAP). EAP encompasses many different propulsion system architectures which can also enable new, synergistic propulsion-airframe integration approaches. This report evaluates the combination of turboelectric EAP and fuselage boundary layer ingestion (BLI) propulsion in a concept called “STARC-ABL.” The predicted fuel consumption benefits of STARC-ABL are updated from a prior 2016 study with new mission requirements and analysis methodologies. Additionally, certification noise is added to the concept evaluation. To properly assess the impact of EAP, a new concept, “ST-ABL,” is developed for comparison which includes the fuselage BLI propulsor driven mechanically instead of by a turboelectric system. STARC-ABL is predicted to provide a 3.4% reduction in fuel consumption for a single-aisle class, 3500 nmi design mission and a 2.7% reduction for a 900 nmi mission, both relative to an advanced technology conventional aircraft. STARC-ABL is also predicted to have a Chapter 14 cumulative noise margin of 7 EPNdB. The non-EAP ST-ABL concept results in slightly higher fuel consumption and noise than STARC-ABL, indicating that the turboelectric system provides benefits over the mechanical drive approach to fuselage BLI. Areas for future research and evolution of the concept include assessing its applicability to other aircraft sizes, increasing the fidelity of BLI and electric component modeling, and investigating other EAP architecture options.

BLI↗
NASA NTRSDate not supplied

Electrical System Trade Study for SUSAN Electrofan Concept Vehicle

The SUSAN Electrofan Aircraft concept is a subsonic regional jet transport aircraft that utilizes a single turbofan engine and Electrified Aircraft Propulsion (EAP) to enable propulsive and aerodynamic benefits to reduce fuel usage, emissions, and cost. This paper is a trade space exploration of the electrical system for the concept aircraft, including possible system architectures, and a review of the specific powers and efficiencies required for the electrical components to realize the EAP system.

Joseph M Haglage↗
NASA NTRSDate not supplied

Comparing the Electrical Modeling and Thermal Analysis Toolbox Simulation Data to Electrified Aircraft Propulsion Test Hardware Data

A model using the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), a National Aeronautics and Space Administration (NASA)-developed Simulink® model block library of electrical components, was developed to mirror the Hybrid Propulsion Emulation Rig (HyPER) hardware, a laboratory focused on Electrified Aircraft Propulsion (EAP) hardware tests. The goal of the model was to demonstrate the utility of the library by comparing the accuracy of the library models to the performance of real hardware, with the primary metrics being the simulation outputs matching physical test hardware data within 5% of full scale.The objective of this paper is to present the background, setup, testing and results of this comparison. It describes some of the adjustments that were necessary to match the system hardware, as well as next steps in verification and validation. The outputs of the model were compared to the results of several tests in HyPER, and in the process captured an additional torque loss that is still being analyzed for the root cause but has been confirmed in the hardware. Across all the test series, only one key model parameter was outside the target 5% full scale matching, and nearly 70% were within 1%.

Mark E Bell↗
NASA NTRS2023

Comparing the Electrical Modeling and Thermal Analysis Toolbox Simulation Data to Electrified Aircraft Propulsion Test Hardware Data

A model using the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), a National Aeronautics and Space Administration (NASA)-developed Simulink® model block library of electrical components, was developed to mirror the Hybrid Propulsion Emulation Rig (HyPER) hardware, a laboratory focused on Electrified Aircraft Propulsion (EAP) hardware tests. The goal of the model was to demonstrate the utility of the library by comparing the accuracy of the library models to the performance of real hardware, with the primary metrics being the simulation outputs matching physical test hardware data within 5 percent of full scale. The objective of this paper is to present the background, setup, testing and results of this comparison. It describes some of the adjustments that were necessary to match the system hardware, as well as next steps in verification and validation. The outputs of the model were compared to the results of several tests in HyPER, and in the process captured an additional torque loss that is still being analyzed for the root cause but has been confirmed in the hardware. Across all the test series, only one key model parameter was outside the target 5 percent full scale matching, and nearly 70 percent were within 1 percent.

Mark E. Bell↗
NASA NTRS2023

ISM In-Space Manufacturing

In-Space Manufacturing (ISM), managed out of the Marshall Space Flight Center, is working to provide capabilities for on-demand sustainable manufacturing of mechanical and electrical components during NASA Exploration Missions (transit and on-surface). ISM continues to pursue the development and evaluation of new technologies that will be applied in space for years to come.

Zach Courtright↗
NASA NTRSDate not supplied

Electronic Speed Controller Thermal Management

This experiment was coupled with an acoustic test for NASA’s QUiet Electric ENgine (QUEEN). A cold plate with water was used to cool the electronic speed controller of the motor under different conditions (shown on right). Part 1: Fixed motor RPM, translating to fixed power/heat dissipation (4W per MOSFET) of electrical components, with variable cooling capacity measured by flow rate of cold plate water in gpm. Part 2: Fixed cooling power (1 gpm) with variable RPM.

thermal↗
NASA NTRS2016

Sizing Power Components of an Electrically Driven Tail Cone Thruster and a Range Extender

The aeronautics industry has been challenged on many fronts to increase efficiency, reduce emissions, and decrease dependency on carbon-based fuels. The NASA Aeronautics Research Mission Directorate has identified a suite of investments to meet long term research demands beyond the purview of commercial investment. Electrification of aviation propulsion through turboelectric or hybrid electric propulsion is one of many exciting research areas which has the potential to revolutionize the aviation industry. This paper will provide an overview of the turboelectric and hybrid electric technologies being developed under NASAs Advanced Air Transportation Technology (AATT) Project, and how these technologies can impact vehicle design. An overview will be presented of vehicle system studies and the electric drive system assumptions for successful turboelectric and hybrid electric propulsion in single aisle size commercial aircraft. Key performance parameters for electric drive system technologies will be reviewed, and the technical investment made in materials, electric machines, power electronics, and integrated power systems will be discussed. Finally, power components for a single aisle turboelectric aircraft with an electrically driven tail cone thruster and a hybrid electric nine passenger aircraft with a range extender will be parametrically sized.

turbogenerator↗
NASA NTRS2016

Sizing Power Components of an Electrically Driven Tail Cone Thruster and a Range Extender

The aeronautics industry has been challenged on many fronts to increase efficiency, reduce emissions, and decrease dependency on carbon-based fuels. This paper provides an overview of the turboelectric and hybrid electric technologies being developed under NASA's Advanced Air Transportation Technology (AATT) Project and discusses how these technologies can impact vehicle design. The discussion includes an overview of key hybrid electric studies and technology investments, the approach to making informed investment decisions based on key performance parameters and mission studies, and the power system architectures for two candidate aircraft. Finally, the power components for a single-aisle turboelectric aircraft with an electrically driven tail cone thruster and for a hybrid-electric nine-passenger aircraft with a range extender are parametrically sized, and the sensitivity of these components to key parameters is presented.

hybrid propulsion↗
NASA NTRS2000

Reliability Modeling of Microelectromechanical Systems Using Neural Networks

Microelectromechanical systems (MEMS) are a broad and rapidly expanding field that is currently receiving a great deal of attention because of the potential to significantly improve the ability to sense, analyze, and control a variety of processes, such as heating and ventilation systems, automobiles, medicine, aeronautical flight, military surveillance, weather forecasting, and space exploration. MEMS are very small and are a blend of electrical and mechanical components, with electrical and mechanical systems on one chip. This research establishes reliability estimation and prediction for MEMS devices at the conceptual design phase using neural networks. At the conceptual design phase, before devices are built and tested, traditional methods of quantifying reliability are inadequate because the device is not in existence and cannot be tested to establish the reliability distributions. A novel approach using neural networks is created to predict the overall reliability of a MEMS device based on its components and each component's attributes. The methodology begins with collecting attribute data (fabrication process, physical specifications, operating environment, property characteristics, packaging, etc.) and reliability data for many types of microengines. The data are partitioned into training data (the majority) and validation data (the remainder). A neural network is applied to the training data (both attribute and reliability); the attributes become the system inputs and reliability data (cycles to failure), the system output. After the neural network is trained with sufficient data. the validation data are used to verify the neural networks provided accurate reliability estimates. Now, the reliability of a new proposed MEMS device can be estimated by using the appropriate trained neural networks developed in this work.

Perera. J. Sebastian↗
NASA NTRS1991

Electrical emissions of airplanes flying in electrified clouds and their effect on airplane measurements of cloud electric fields

The signature of the cloud electric field components deduced from measurements made with electric field meters carried on airplane penetrating electrified clouds is often complex, especially when the airplane experiences strong electrical charging. However, simple electric field variations were obtained for penetrations involving severe charging of the airplane on flights over KSC on 19 Aug. 1989. During these episodes of severe electrical charging, the airplane typically became negatively charged as it approached a region of negative cloud charge and then became positively charged as it receded from the cloud charge. The charge acquired by the airplane within the cloud was so large that the electric fields at the faces of the mills mounted on the fuselage were as large as for an ambient electric field of 60 to 80 kV/m. However, the deduced electric field components perpendicular to the direction of flight, to which these mills respond, were only about 5 to 10 kV/m. The variation of the deduced ambient field component in the direction of flight was antisymmetric about the charge region for these penetrations. Analysis of these results suggest that intense plumes of electric charge were emitted from the airplane and that the electric field associated with these plumes overcame the electric field due to the cloud charge at the tail-mounted field mill. As a consequence, the deduced component of the ambient electric field in the direction of flight was severely distorted. These findings emphasize the need for careful evaluation of airplane electric field measurements and of the need for further work on techniques for improving the measurements.

Jones, James J.↗
NASA NTRS1983

Advanced electrical power system technology for the all electric aircraft

The application of advanced electric power system technology to an all electric airplane results in an estimated reduction of the total takeoff gross weight of over 23,000 pounds for a large airplane. This will result in a 5 to 10 percent reduction in direct operating costs (DOC). Critical to this savings is the basic electrical power system component technology. These advanced electrical power components will provide a solid foundation for the materials, devices, circuits, and subsystems needed to satisfy the unique requirements of advanced all electric aircraft power systems. The program for the development of advanced electrical power component technology is described. The program is divided into five generic areas: semiconductor devices (transistors, thyristors, and diodes); conductors (materials and transmission lines); dielectrics; magnetic devices; and load management devices. Examples of progress in each of the five areas are discussed. Bipolar power transistors up to 1000 V at 100 A with a gain of 10 and a 0.5 microsec rise and fall time are presented. A class of semiconductor devices with a possibility of switching up to 100 kV is described. Solid state power controllers for load management at 120 to 1000 V and power levels to 25 kW were developed along with a 25 kW, 20 kHz transformer weighing only 3.2 kg.

Finke, R. C.↗