Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EFFECT OF COMPRESSIBILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Use of potential flow theory to evaluate subsonic inlet data from a simulator-powered nacelle at cruise conditions

Incompressible potential flow theory corrected for compressibility effects, using the Lieblein-Stockman compressibility correction, was used to predict surface and flow field static pressures for a subsonic inlet at cruise conditions. The calculated internal and external surface static pressures were in good agreement with data at most conditions. The analysis was used to determine the capture stream-tube location and static-pressure distribution. Additive drag coefficients obtained from these results were consistently higher than those obtained using one-dimensional compressible flow theory. Increasing the distance between the inlet and boattail increased the cowl drag force. The effect of the boundary layer on internal and external surface static-pressure distributions was small at the design cruise condition. The analytical results may be used as an aid to data reduction and for predicting inlet mass flow, stagnation point location, and inlet additive drag.

Bober, L. J.↗
NASA NTRS2000

Anisotropic Nanomechanics of Boron Nitride Nanotubes: Nanostructured "Skin" Effect

The stiffness and plasticity of boron nitride nanotubes are investigated using generalized tight-binding molecular dynamics and ab-initio total energy methods. Due to boron-nitride BN bond buckling effects, compressed zigzag BN nanotubes are found to undergo novel anisotropic strain release followed by anisotropic plastic buckling. The strain is preferentially released towards N atoms in the rotated BN bonds. The tubes buckle anisotropically towards only one end when uniaxially compressed from both. A "skin-effect" model of smart nanocomposite materials is proposed which will localize the structural damage towards the 'skin' or surface side of the material.

Srivastava, Deepak↗
NASA NTRS1989

Flow visualization studies of the Mach number effects on the dynamic stall of an oscillating airfoil

Compressibility effects on the dynamic stall of a NACA 0012 airfoil undergoing sinusoidal oscillatory motion were studied using a stroboscopic schlieren system. Schlieren pictures and some quantitative data derived from them are presented and show the influence of free-stream Mach number and reduced frequency on the dynamic-stall vortex. This study shows that a dynamic stall vortex always forms near the leading edge and convects on the airfoil upper surface at approximately 0.3 times the free stream velocity for all cases studied. The results also demonstrate that initiation of the dynamic stall vortex is delayed to higher angles of attack with increased reduced frequency, but that dynamic stall occurs at lower angles of incidence with increasing Mach numbers.

Chandrasekhara, M. S.↗
NASA NTRS1985

Three-dimensional airflow and hydrometeor trajectory calculation with applications

Numerical codes developed to model potential flows about three-dimensional bodies and applied to examining the flowfields around aircraft nose probes for gathering hydrometeor data are described. The potential flow code accounts for lifting or nonlifting surfaces, the effects of lift vorticity, inlet flows, and compression effects. Particle trajectories are calculated using particle equations of motion, with note taken of conditions in both the far- and near-fields of the flow. Graphic projections of the trajectories can be made from any view angle using another code. The codes also contain routines for handling flow velocities around arrays of spatial locations, trajectory arrays, and the effects of flow distortion on the particle flux.

Norment, H. G.↗
NASA NTRS2000

Description of Panel Method Code ANTARES

Panel method code ANTARES was developed to compute wall interference corrections in a rectangular wind tunnel. The code uses point doublets to represent blockage effects and line doublets to represent lifting effects of a wind tunnel model. Subsonic compressibility effects are modeled by applying the Prandtl-Glauert transformation. The closed wall, open jet, or perforated wall boundary condition may be assigned to a wall panel centroid. The tunnel walls can be represented by using up to 8000 panels. The accuracy of panel method code ANTARES was successfully investigated by comparing solutions for the closed wall and open jet boundary condition with corresponding Method of Images solutions. Fourier transform solutions of a two-dimensional wind tunnel flow field were used to check the application of the perforated wall boundary condition. Studies showed that the accuracy of panel method code ANTARES can be improved by increasing the total number of wall panels in the circumferential direction. It was also shown that the accuracy decreases with increasing free-stream Mach number of the wind tunnel flow field.

Ulbrich, Norbert↗
NASA NTRS1994

Low-Noise Rotorcraft Blades

Blades of helicopter rotors, tilt rotors, and like reshaped to reduce noise, according to proposal. Planform features combination of rearward and forward sweep. Forward sweep over large outer portion of blade constitutes primary noise-reduction feature. Relieves some of compressive effect in tip region, with consequent reduction of noise from compressive sources. Performance at high advance ratio improved. Cabin vibration and loading noise reduced by load-averaging effect of double-sweep planform. Aft-swept section provides balancing of aerodynamic and other dynamic forces on blade along 1/4-chord line of straight inboard section and along projection of line to outermost blade radius. Possible for hub-hinge forces and moments to remain within practical bounds. Provides stabilizing blade forces and moments to counteract any instability caused by forward sweep.

Brooks, Thomas F.↗
NASA NTRS2003

Thermal Effects on the Compressive Behavior of IM7/PET15 Laminates

The effect of changing operating temperature on the compressive response of IM7/PETI5 composite laminates is investigated within this paper. The three temperatures evaluated for this study were 129 C, 21 C, and 177 C, a spectrum from cryogenic to an elevated operating temperature. Laminate compressive strength property testing was conducted using the Wyoming Combined Load Compression fixture to generate strength data at the three operating temperatures of interest for several lay-ups. A three-dimensional finite element analysis model of a [90/0]8s composite laminate subject to compressive loading is developed. The model is used to study the key attributes of the laminate that significantly influence the state of stress in the laminate. Both the resin rich layer located between lamina and the thermal residual stresses present in the laminate due to curing are included in the analysis model. For the laminate modeled, the effect of modeling temperature dependent material properties was determined to be insignificant for the operating temperatures studied. Simply using the material properties measured at the operating temperature of interest was sufficient for predicting stresses accurately in a linear analysis for the current problem. The three-dimensional analysis results revealed that the application of an applied compressive axial load in the 0-degree direction decreased the interlaminar stresses present in the laminate initially due to curing. Therefore, failure was concluded not be attributable to the interlaminar stresses in the composite laminate being studied when a compressive load is applied. The magnitude of the measured laminate compressive strength change with a change in temperature is concluded to be dominated by the change in the lamina compressive axial strength with a change in temperature.

Walker, Sandra Polesky↗
NASA NTRS1998

Studies of Shock Wave Interactions with Homogeneous and Isotropic Turbulence

A nearly homogeneous nearly isotropic compressible turbulent flow interacting with a normal shock wave has been studied experimentally in a large shock tube facility. Spatial resolution of the order of 8 Kolmogorov viscous length scales was achieved in the measurements of turbulence. A variety of turbulence generating grids provide a wide range of turbulence scales. Integral length scales were found to substantially decrease through the interaction with the shock wave in all investigated cases with flow Mach numbers ranging from 0.3 to 0.7 and shock Mach numbers from 1.2 to 1.6. The outcome of the interaction depends strongly on the state of compressibility of the incoming turbulence. The length scales in the lateral direction are amplified at small Mach numbers and attenuated at large Mach numbers. Even at large Mach numbers amplification of lateral length scales has been observed in the case of fine grids. In addition to the interaction with the shock the present work has documented substantial compressibility effects in the incoming homogeneous and isotropic turbulent flow. The decay of Mach number fluctuations was found to follow a power law similar to that describing the decay of incompressible isotropic turbulence. It was found that the decay coefficient and the decay exponent decrease with increasing Mach number while the virtual origin increases with increasing Mach number. A mechanism possibly responsible for these effects appears to be the inherently low growth rate of compressible shear layers emanating from the cylindrical rods of the grid.

Briassulis, G.↗
NASA NTRS1993

Effect of fluid compressibility on journal bearing performance

An analysis was undertaken to determine the effect of fluid film compressibility on the performance of fluid film bearings. A new version of the Reynolds equation was developed, using a polytropic expansion, for both steady-state and dynamic conditions. Polytropic exponents from 1 (isothermal) to 1000 (approaching an incompressible liquid) were evaluated for two bearing numbers, selected from a range of practical interest for cryogenic application, and without cavitation. Bearing loads were insensitive to fluid compressibility for low bearing numbers, as was expected. The effect of compressibility on attitude angle was significant, even when the bearing number was low. A small amount of fluid compressibility was enough to obtain stable running conditions. Incompressible liquid lacked stability at all conditions. Fluid compressibility can be used to control the bearing dynamic coefficients, thereby influencing the dynamic behavior of the rotor-bearing system.

Dimofte, Florin↗
NASA NTRS1989

Evolution of the Orszag-Tang vortex system in a compressible medium. I - Initial average subsonic flow

The results of fully compressible, Fourier collocation, numerical simulations of the Orszag-Tang vortex system are presented. The initial conditions for this system consist of a nonrandom, periodic field in which the magnetic and velocity field contain X points but differ in modal structure along one spatial direction. The velocity field is initially solenoidal, with the total initial pressure field consisting of the superposition of the appropriate incompressible pressure distribution upon a flat pressure field corresponding to the initial, average Mach number of the flow. In these numerical simulations, this initial Mach number is varied from 0.2-0.6. These values correspond to average plasma beta values ranging from 30.0 to 3.3, respectively. It is found that compressible effects develop within one or two Alfven transit times, as manifested in the spectra of compressible quantities such as the mass density and the nonsolenoidal flow field. These effects include (1) a retardation of growth of correlation between the magnetic field and the velocity field, (2) the emergence of compressible small-scale structure such as massive jets, and (3) bifurcation of eddies in the compressible flow field. Differences between the incompressible and compressible results tend to increase with increasing initial average Mach number.

Dahlburg, R. B.↗
NASA NTRS1980

Aero-optics overview

Various aero-optical phenomena are discussed with reference to their effect on airborne high energy lasers. Major emphasis is placed on: compressibility effects induced in the surrounding flow field; viscous effects which manifests themselves as aircraft boundary layers or shear layers; inviscid flow fields surrounding the aircraft due to airflow around protuberance such as laser turret assemblies; and shocks, established whenever local flow exceeds Mach one. The significant physical parameters affecting the interaction of a laser beam with a turbulent boundary layer are also described.

Gilbert, K. G.↗
NASA NTRS1986

Flight research on natural laminar flow

Five decades of flight experiences with natural laminar flow (NLF) have provided a basis of understanding how this technology can be used for reduction of viscous drag on modern practical aircraft. The effects of cruise unit Reynolds number on NLF achievability and maintainability; compressibility effects on Tollmein-Schlichting growth; flight experiment on the Cessna Citation III business jet; flight instrumentation on Lear 28/29; OV-I NLF engine nacelle experiments; and viscous drag reduction are examined.

Holmes, B. J.↗
NASA NTRS1990

Modeling of compressible turbulence

The work is directed toward understanding and modeling compressibility effects in turbulent flows. The primary objective is to investigate how compressibility influences the basic turbulence processes such as turbulence production and dissipation, length scale modification, spectral energy transfer, etc. The second objective is to develop parameterization schemes and models to incorporate compressibility into one-point closure models and into the subgrid scale models for LES techniques. The ultimate purpose of this research is to develop compressible turbulence models which are capable of handling the hypersonic regime. Specifically, the emphasis will be on the model capability of predicting: (1) heat and momentum transfer in hypersonic boundary layers; and (2) mixing and growth of high Mach number shear layers, jet and wakes.

Zeman, O.↗
NASA NTRS1990

F-18 high alpha research vehicle surface pressures: Initial in-flight results and correlation with flow visualization and wind-tunnel data

Pressure distributions measured on the forebody and the leading-edge extensions (LEX's) of the NASA F-18 high alpha research vehicle (HARV) were reported at 10 and 50 degree angles of attack and at Mach 0.20 to 0.60. The results were correlated with HARV flow visualization and 6-percent scale F-18 wind-tunnel-model test results. The general trend in the data from the forebody was for the maximum suction pressure peaks to first appear at an angle of attack (alpha) of approximately 19 degrees and increase in magnitude with angle of attack. The LEX pressure distribution general trend was the inward progression and increase in magnitude of the maximum suction peaks up to vortex core breakdown and then the decrease and general flattening of the pressure distribution beyond that. No significant effect of Mach number was noted for the forebody results. However, a substantial compressibility effect on the LEX's resulted in a significant reduction in vortex-induced suction pressure as Mach number increased. The forebody primary and the LEX secondary vortex separation lines, from surface flow visualization, correlated well with the end of pressure recovery, leeward and windward, respectively, of maximum suction pressure peaks. The flight to wind-tunnel correlations were generally good with some exceptions.

Fisher, David F.↗
NASA NTRS1984

Hole interaction and load introduction effects for compression-loaded laminates with holes

The effects of hole interaction and load introduction for (+ or - 30/90) sub 8 (s) and (+ or - 45) sub 12 (s) laminates with holes was conducted. A hole interaction region was identified in some specimens, and this region was ineffective for carrying load. The membrane stiffness of a specimen with a hole interaction region is less than the membrane stiffness of a similar specimen without a hole interaction region. A load introduction effect that occurs on the sublaminate level was also observed. This effect can cause a nonuniform load diffusion into the interior of the specimen.

Shuart, M. J.↗