Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EARTH SHAPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Small craters on the meteoroid and space debris impact experiment

Examination of 9.34 m(exp 2) of thick aluminum plates from the Long Duration Exposure Facility (LDEF) using a 25X microscope revealed 4341 craters that were 0.1 mm in diameter or larger. The largest was 3 mm in diameter. Most were roughly hemispherical with lips that were raised above the original plate surface. The crater diameter measured was the diameter at the top of the raised lips. There was a large variation in the number density of craters around the three-axis gravity-gradient stabilized spacecraft. A model of the near-Earth meteoroid environment is presented which uses a meteoroid size distribution based on the crater size distribution on the space end of the LDEF. An argument is made that nearly all the craters on the space end must have been caused by meteoroids and that very few could have been caused by man-made orbital debris. However, no chemical analysis of impactor residue that will distinguish between meteoroids and man-made debris is yet available. A small area (0.0447 m(exp 2)) of one of the plates on the space end was scanned with a 200X microscope revealing 155 craters between 10 micron and 100 micron in diameter and 3 craters smaller than 10 micron. This data was used to extend the size distribution of meteoroids down to approximately 1 micron. New penetration equations developed by Alan Watts were used to relate crater dimensions to meteoroid size. The equations suggest that meteoroids must have a density near 2.5 g/cm(exp 3) to produce craters of the shape found on the LDEF. The near-Earth meteoroid model suggests that about 80 to 85 percent of the 100 micron to 1 mm diameter craters on the twelve peripheral rows of the LDEF were caused by meteoroids, leaving 15 to 20 percent to be caused by man-made orbital debris.

Humes, Donald H.↗
NASA NTRS1986

Preparation, analysis and release of simulated interplanetary grains into low Earth orbit

Astronomical observations which reflect the optical and dynamical properties of interstellar and interplanetary grains are the primary means of identifying the shape, size, and the chemistry of extraterrestrial grain materials. Except for recent samplings of extraterrestrial particles in near-Earth orbit and in the stratosphere observations were the only method of deducing the properties of extraterrestrial particles. In order to elucidate the detailed characteristics of observed dust, the observations must be compared with theoretical studies, some of which are discussed in this volume, or compared with terrestrial laboratory experiments. The formation and optical characterization of simulated interstellar and interplanetary dust with particular emphasis on studying the properties on irregularly shaped particles were discussed. Efforts to develop the techniques to allow dust experiments to be carried out in low-Earth orbit were discussed, thus extending the conditions under which dust experiments may be performed.

Stephens, J. R.↗
NASA NTRS2018

Modeling and Flight Performance of Supersonic Disk-Gap-Band Parachutes in Slender Body Wakes

NASA's ASPIRE (Advanced Supersonic Parachute Inflation Research and Experiments) project is investigating the supersonic deployment and inflation of full-scale parachutes. To achieve Mars-relevant conditions, the parachutes are deployed at high altitudes over Earth on a sounding rocket platform. During the flight test, Disk-Gap-Band parachutes of 21.5 meter diameter are deployed behind a slender payload 1/6th the diameter of the blunt Mars2020 capsule. Due to the differences in leading body geometry between the test flight and a parachute deployment at Mars, high fidelity numerical simulations of slender and blunt bodywakes, and of rigid parachutes behind them, were used to understand differences and similarities in the flow and the effect on parachute drag. The slender body wake is thinner, closes earlier, and presents a smaller wake deficit. Thus, a parachute deployed in the wake of a slender body is more likely to see a higher dynamic pressure than a parachute deployed behind a blunt body. In the presence of a parachute, the interaction of the unsteady wake with the parachute bow shock is stronger behind the blunt body. Simulations yield highly unsteady forces on the parachute, which was modeled as a rigid body. The mean parachute force behind a slender body is between 3 and 12 percent higher than behind a blunt body, depending on the angle of the parachute with the flow. As the angle of incidence increases, more of the parachute moves out of the leading body wakes, decreasing the sensitivity to leading body shape. To compare the flow past parachutes in Earth's and Mars' atmospheres, simulations were also performed in CO2. At the Mach number considered (1.75), the shock standoff distance ahead of the parachute, post-shock jump conditions, and the resulting parachute forces were found to be very similar in both air and CO2, indicating that a high altitude test is a good proxy for a Mars descent. The results of these numerical simulations and available data on past flight and wind tunnel tests of supersonic Disk-Gap-Band parachutes behind slender bodies were used to generate a parachute drag model for ASPIRE, which in turn was used to help design the flight test. The first flight test occurred in October 2017. The parachute was successfully deployed at Mach 1.77 and an altitude of 42 kilometers. Test instrumentation provided the atmospheric conditions, test vehicle trajectory, and the loads on the parachute along with detailed high-resolution imagery of the inflation process. Reconstruction of the flight test indicated that the measured forces on the parachute were within the model's bounds, although the model over-predicted the parachute force during the first few seconds. The parachute forces during the long subsonic period were well-predicted by the ASPIRE drag model.

Muppidi, Suman↗
NASA NTRS2004

Visible/Near-Infrared Spectral Properties of MUSES C Target Asteroid 25143 Itokawa

The Japanese MUSES C mission launched the Hayabusa spacecraft last May 15, 2003, to encounter and study the near-Earth asteroid 25143 Itokawa. The spacecraft will obtain visible images through broadband filters similar to the ECAS filters, and near-infrared spectra from 0.85 - 2.1 microns. In preparation for this encounter, opportunities to study the asteroid with Earth-based telescopes have been fully leveraged. Visible and near-infrared spectral observations were made of asteroid 25143 Itokawa during several nights of March, 2001, around the last apparition. We report here on the results of extensive spectral observations made to address the questions of compositional variations across the surface of the asteroid (as determined by the rotational period and shape model); variations in phase angle (Sun-Itokawa-Earth angle) on spectral characteristics; and predictions of Itokawa observations by Hayabusa based on the spectral resolution and responsivity of the NIRS and AMICA instruments.

Jarvis, K. S.↗
NASA NTRSDate not supplied

Phase transition energetics-based mass loss modeling of chondritic Near Earth Objects

Mitigating potentially hazardous asteroids relies on accurate knowledge of their composition and critical physical characteristics such as shape and mass. Ground-based observatories and sample return missions in recent years have focused on such characterization to track Near Earth Objects. Historically, entry speeds of asteroids or mass change due to break-up/airburst have been considered in risk assessment studies as critical parameters. To this effect, most hydrocode simulations that consider energy deposition techniques rely on gross meteor modeling with simplistic spherical shapes while neglecting heat of ablation considerations. This is the general approach for fragment-cloud, pancake and hybrid fragmentation models. Alternatively, aerothermal fragmentation modeling that accounts for meteoritic shape change have typically focused on environmental modeling to understand break-up points primarily due to radiative heating. A physics-based risk assessment could benefit by modeling the environment and material response of typical meteoroidal materials as precursors to fragmentation. A greater focus on the material response to applied environmental heating will be emphasized here. This work presents a forward analysis of thermal and material response of stony meteorites by ac-counting for mass loss and shape change effects through a boundary layer formalism. This allows for simulations starting from simplistic shapes that could eventually lead to alterations in contours due to ablation. These effects would be characterized through phase transitions of the surface, such as melting and vaporization, in response to aerodynamic heating. Coupled ablation and radiative heating effects have been found to lead to reduced heat transfer coefficients in the computation of meteor mass loss rates. This has the potential to increase ground damage footprints for hazardous impacts. The effort here quantifies the heat transfer coefficient by accounting for ablation assisted by phase transition. The melt and vaporization mediated ablation of chondritic meteors provides essential recession estimates based upon surface environments. The altered mass due to such phenomena would be presented for a H-chondrite meteoritic sample.

Pratibha Raghunandan↗
NASA NTRS1973

Robot vision.

The work reported had been undertaken to develop hardware that would guide an automatic vehicle in the exploration of the surface of Mars, recognize objects, and report the findings to earth. Approaches for automatically determining the range and shape of objects are discussed, giving attention to the automatic comparison of one scan line of the left with one scan line of the right TV image. Methods of mapping binocular space into match space are considered together with the use of a model in match space, rules for processing random-dot stereograms, the elimination of spurious matches, random-square stereograms, questions of the processing of a real scene, and aspects of range accuracy. Methods of computation for extracting other features are also discussed along with stereo TV cameras and approaches for reconstructing the appearance of a scene.

Sutro, L. L.↗
NASA NTRS1984

Planetary Mach cones - Theory and observation

The asymptotic behavior of planetary bow shocks and the ability of gas dynamic theory to describe it are studied. Spacecraft observations at Venus, earth, and Mars are used to model the shapes and positions of their distant bow waves. The measured planetary Mach cone angles are compared with the mean sonic and MHD fast wave Mach numbers at 0.7, 1.0, and 1.5 AU to assess the downstream influence of the interplanetary magnetic field. Numerical gas dynamic flow solutions extending to 50 obstacle radii behind each planet are obtained and tested against the observed location of the downstream bow shock.

Slavin, J. A.↗
NASA NTRS1985

Launching rockets and small satellites from the lunar surface

Scientific payloads and their propulsion systems optimized for launch from the lunar surface differ considerably from their counterparts for use on earth. For spin-stabilized payloads, the preferred shape is a large diameter-to-length ratio to provide stability during the thrust phase. The rocket motor required for a 50-kg payload to reach an altitude of one lunar radius would have a mass of about 41 kg. To place spin-stabilized vehicles into low altitude circular orbits, they are first launched into an elliptical orbit with altitude about 840 km at aposelene. When the spacecraft crosses the desired circular orbit, small retro-rockets are fired to attain the appropriate direction and speed. Values of the launch angle, velocity increments, and other parameters for circular orbits of several altitudes are tabulated. To boost a 50-kg payload into a 100-km altitude circular orbit requires a total rocket motor mass of about 90 kg.

Anderson, K. A.↗
NASA NTRS1988

Effects of cirrus composition on atmospheric radiation budgets

A radiative transfer model that can be used to determine the change in solar and infrared fluxes caused by variations in the composition of cirrus clouds was used to investigate the importance of particle size and shape on the radiation budget of the Earth-atmosphere system. Even though the cloud optical thickness dominates the radiative properties of ice clouds, the particle size and nonsphericity of ice crystals are also important in calculations of the transfer of near-IR solar wavelengths. Results show that, for a given optical thickness, ice clouds composed of larger particles would produce larger greenhouse effects than those composed of smaller particles. Moreover, spherical particles with equivalent surface areas, frequently used for ice crystal clouds, would lead to an overestimation of the greenhouse effect.

Kinne, Stefan↗
NASA NTRS1989

Radar detection of Phobos

Radar echoes from the martian satellite Phobos provide information about that object's surface properties at scales near the 3.5-cm observing wavelength. Phobos appears less rough than the moon at centimeter-to-decimeter scales. The uppermost few decimeters of the satellite's regolith have a mean bulk density within 20 percent of 2.0 g/cu cm. The radar signature of Phobos (albedo, polarization ratio, and echo spectral shape) differs from signatures measured for small, earth-approaching objects, but resembles those of large (greater than 100-km), C-class, mainbelt asteroids.

Ostro, S. J.↗
NASA NTRS1989

Effect of earth albedo variation on the performance of spatial acquisition subsystem aboard a planetary spacecraft

Deep-space optical communication systems generally require the use of the sunlit earth as the pointing reference. For simple single-frame spatial acquisition processors, the uncertainties in earth albedo can result in an irreducible error in acquiring the spatial location of the receiver. Multiple frame processing algorithms can be used to estimate the earth albedo. The prior knowledge of the image shape and orientation can then be used to derive the location of the receiver.

Chen, Chien-Chung↗
NASA NTRS1990

Radiation force modeling for the Topex/Poseidon spacecraft

The largest nongravitational forces that will be acting on the Topex satellite will be those due to incident and emitted radiation on the spacecraft surfaces. In order to minimize the effects of these forces on orbit determination, a detailed model is being developed so that they may be accurately predicted. This model requires a precise description of the spacecraft shape and orientation, evaluation of the solar and earth radiation impinging on the surfaces, and a determination of the radiation being emitted from the surfaces as they heat and cool throughout the orbit. The TRASYS software system is used to evaluate the solar and earth radiation striking each surface of the spacecrat. This software has been modified to include an earth radiation model which follows the seasonal variations in albedo and IR radiation. The SINDA software system is then used to determine the transient temperatures of the spacecraft surfaces.

Rosborough, George W.↗
NASA NTRS2002

STS-109 Flight Day 3 Highlights

This footage from the third day of the STS-109 mission to service the Hubble Space Telescope (HST) begins with the grappling of the HST by the robotic arm of the Columbia Orbiter, operated by Mission Specialist Nancy Currie. During the grappling, numerous angles deliver close-up images of the telescope which appears to be in good shape despite many years in orbit around the Earth. Following the positioning of the HST on its berthing platform in the Shuttle bay, the robotic arm is used to perform an external survey of the telescope. Some cursory details are given about different equipment which will be installed on the HST including a replacement cooling system for the Near Infrared Camera Multi-Object Spectrometer (NICMOS) and the Advanced Camera for Surveys. Following the survey, there is footage of the retraction of both of the telescope's two flexible solar arrays, which was successful. These arrays will be replaced by rigid solar arrays with decreased surface area and increased performance.

Source record↗
NASA NTRS1961

Subsonic Longitudinal Aerodynamic Characteristics of Disks with Elliptic Cross Sections and Thickness-Diameter Ratios from 0.225 to 0.425

General interest in manned space flight has provided a stimulus for the investigation of shapes which appear to be attractive for application to re-entry vehicles. Such vehicles can be classed as either nonlifting or lifting. Nonlifting types, such as used in Project Mercury, have certain advantages which include structural simplicity, no requirement for an elaborate flight-control system, ease of mating with the booster, and short exposure times to high heating rates during entry. Advantages of lifting types, by comparison, include lower peak heating rates and decelerations, the possibility for a conventional horizontal landing, and the ability to maneuver, thus providing control over longitudinal and lateral range and a wider entry corridor on return from planetary or lunar missions. A lifting shape which appears attractive in terms of the considerations is a thick disk. At high attitudes, the weight to drag ratio is low and the radius of curvature of the surface exposed to the airstream is large, a combination of parameters which results in reduced convective heating rates. The low-speed lift-drag ratios associated with this type of shape appear sufficiently high to permit a conventional horizontal landing. The investigation reported herein was undertaken to assess the effects of thickness on the aerodynamic characteristics of disk shapes suitable for lifting re-entry into the earth's atmosphere and potentially capable of conventional horizontal landing. The models had elliptic cross sections which varied in thickness from 0.225 to 0.425 diameter. The tests were conducted in the Ames 12-Foot Pressure Wind Tunnel over a Mach number range from 0.25 to 0.90 at a Reynolds number of 3.3x10 (exp 6) and at Reynolds numbers to 16x10 (exp 6) at a Mach number of 0.25. Tests on similar shapes have been conducted at subsonic, transonic, and supersonic speeds and the results have been presented.

Demele, Fred A.↗
NASA NTRS1982

Plasma injection and transport in the mid-altitude polar cusp

DE-1 hot plasma observations in the mid-altitude polar cusp have shown evidence of a significant velocity filtering phenomenon which is consistent with a latitudinally narrow region of plasma injection located at a geocentric distance of about eight earth radii (in a dipole approximation). Plasma convection from the injection region into the polar cap results in a V-shaped log E vs. observed pitch angle relation at geocentric distances near 4 earth radii. This velocity filtering effect allows the measurement of much smaller flow velocities (about 10 km/sec) than have heretofore been possible with hot plasma measurements. The flows thus determined are consistent with ionospheric flows measured nearly simultaneously by the DE-2 spacecraft, although the magnitudes of the higher altitude flows are higher by a factor of 2 or more than an approximately r to the 3/2 power dipole-field mapping would predict.

Burch, J. L.↗
NASA NTRS1973

Atmosphere-entry behavior of a modular, disk-shaped, isotope heat source.

The authors have studied the entry and impact behavior of an isotope heat source for space nuclear power that disassembles into a number of modules which would enter the earth's atmosphere separately if a flight aborted. These modules are disk-shaped units, each with its own reentry heat shield and protective impact container. In normal operation, the disk modules are stacked inside the generator, but during a reentry abort they separate and fly as individual units of low ballistic coefficient. Flight tests at hypersonic speeds have confirmed that a stack of disks will separate and assume a flat-forward mode of flight. Free-fall tests of single disks have demonstrated a nominal impact velocity of 30 m/sec at sea level for a practical range of ballistic coefficients.

Vorreiter, J. W.↗
NASA NTRS2014

STEREO as a "Planetary Hazards" Mission

NASA's twin STEREO probes, launched in 2006, have advanced the art and science of space weather forecasting more than any other spacecraft or solar observatory. By surrounding the Sun, they provide previously-impossible early warnings of threats approaching Earth as they develop on the solar far side. They have also revealed the 3D shape and inner structure of CMEs-massive solar storms that can trigger geomagnetic storms when they collide with Earth. This improves the ability of forecasters to anticipate the timing and severity of such events. Moreover, the unique capability of STEREO to track CMEs in three dimensions allows forecasters to make predictions for other planets, giving rise to the possibility of interplanetary space weather forecasting too. STEREO is one of those rare missions for which "planetary hazards" refers to more than one world. The STEREO probes also hold promise for the study of comets and potentially hazardous asteroids.

Heliosphere↗