SEARCH · Engineering Papers

Results for “Dynamic Pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1961

An Investigation of the Effect of Downwash from a VTOL Aircraft and a Helicopter in the Ground Environment

Dynamic-pressure measurement, in ground effect, have been obtained about a single-rotor helicopter and a dual-propeller VTOL (Vertical Take-Off and Landing) aircraft. The results indicate that the slipstream dynamic pressure along the ground, some distance from the center of rotation, is not a function of disk loading but merely a function of the gross weight or thrust of the aircraft. Furthermore, for a given gross weight the thickness of this outward flowing sheet of air is less for a small-diameter propeller (higher disk loading propeller). The variation of the dynamic-pressure flow field for single and dual propellers or rotors is significantly different in the plane of symmetry between the two rotors than in a direction normal to this plane. The interaction of the two flows produces a region of upflow in this plane where the fuselage is located, and the decay of the maximum dynamic pressure with distance ahead of the fuselage is slower.

O'Bryan, Thomas C.↗

NASA NTRS1999

Global Auroral Response to a Solar Wind Pressure Pulse

A global intensification of the aurora was observed by the Ultraviolet Imager on the NASA Polar spacecraft in conjunction with the arrival of the sheath from a solar coronal mass ejection. The aurora was first observed to brighten on the dayside and then the intensification progressed rapidly toward the nightside. During this time the IMP-8 spacecraft in the solar wind recorded a 35-minute period of increased solar wind dynamic pressure. A small substorm (or, possibly pseudobreakup) occurred within a minute of the arrival of the auroral intensification on the nightside in conjunction with a second peak in the dynamic pressure. We propose that the intensification of the aurora can be explained on the basis of the compression of the magnetopause and the generation of hydrodynamic waves by the rapid increase in the solar wind dynamic pressure. It is also evident that the substorm was triggered by waves, generated by a second rise in the dynamic pressure, that propagated to flux tubes connected to the premidnight aurora region.

Brittnacher, M.↗

NASA NTRSDate not supplied

Using Thermally Imperfect and Ideal Gas Equations for Determining Conditions in Slotted Throat Wind Tunnels

The derivation and application of two back pressure controlling methods for setting the dynamic pressure, Mach number, and Reynolds number of subsonic wind tunnels with a slotted-throat test section are discussed. The first method uses a pressure difference to determine the tunnel dynamic pressure via the compressible Bernoulli equations and is used in the ideal gas path in the CFD code. The second method uses an enthalpy difference in the flow to determine the velocity in the test section and can be applied to multispecies, calorically imperfect and calorically perfect gas flow simulations. For a tunnel operating point close to standard atmosphere conditions, Mach number, pressure, and temperature along the tunnel centerline were very closely matched between the various thermodynamic equation assumption controller methods.

Ground Testing↗

NASA NTRS2009

Design of Mach-4 and Mach-6 Nozzles for the NASA LaRC 8-Ft High Temperature Tunnel

The aerodynamic contours for two new nozzles have been designed for the NASA Langley Research Center 8-Foot High Temperature Tunnel. The new Mach-4 and Mach-6 contours have 54.5-inch exit-diameters allowing for testing at high dynamic pressures. The Mach-4 nozzle will extend the test capability of the facility and allow turbine-based combined-cycle propulsion systems to be tested at conditions appropriate for the transition from the turbine to the scramjet flowpath. The Mach-6 nozzle will serve a dual purpose; to provide a Mach-6 test capability at high dynamic pressure and to be used in conjunction with an existing mixer section for testing at lower enthalpy conditions. This second use will extend the life of the existing Mach-7 nozzle which has been used for this purpose. The two new nozzles, in conjunction with existing nozzles, will allow for testing at Mach numbers of 3, 4, 5 and 6 at high dynamic pressures, and Mach 4, 5 and 7 at lower dynamic pressures but larger scales.

Gaffney, Richard L., Jr.↗

NASA NTRS2004

Wind Tunnel to Atmospheric Mapping for Static Aeroelastic Scaling

Wind tunnel to Atmospheric Mapping (WAM) is a methodology for scaling and testing a static aeroelastic wind tunnel model. The WAM procedure employs scaling laws to define a wind tunnel model and wind tunnel test points such that the static aeroelastic flight test data and wind tunnel data will be correlated throughout the test envelopes. This methodology extends the notion that a single test condition - combination of Mach number and dynamic pressure - can be matched by wind tunnel data. The primary requirements for affecting this extension are matching flight Mach numbers, maintaining a constant dynamic pressure scale factor and setting the dynamic pressure scale factor in accordance with the stiffness scale factor. The scaling is enabled by capabilities of the NASA Langley Transonic Dynamics Tunnel (TDT) and by relaxation of scaling requirements present in the dynamic problem that are not critical to the static aeroelastic problem. The methodology is exercised in two example scaling problems: an arbitrarily scaled wing and a practical application to the scaling of the Active Aeroelastic Wing flight vehicle for testing in the TDT.

Heeg, Jennifer↗

NASA NTRS1990

Some buffet response characteristics of a twin-vertical-tail configuration

A rigid, 1/6 size, full span model of an F-18 airplane was fitted with flexible vertical tails of two different levels of stiffness that were buffet tested in the Langley Transonic Dynamics Tunnel. Vertical tail buffet response results that were obtained over the range of angles of attack from -10 to 40 degs, and over the range of Mach numbers from 0.30 to 0.95 are presented. These results indicate the following: (1) the response occurs in the first bending mode; (2) the response increases with increasing dynamic pressure, but changes in response are not linearly proportional to the changes in dynamic pressure; (3) the response is larger at M = 0.30 than it is at the higher Mach numbers; (4) the maximum intensity of the buffeting is described as heavy to severe using an assessment criteria proposed by another investigator; and (5) the data at different dynamic pressures and for the different tails correlate reasonably well using the buffet excitation parameter derived from the dynamic analysis of buffeting.

Cole, Stanley R.↗

NASA NTRS1975

Nonreactive mixing study of a scramjet swept-strut fuel injector

The results are presented of a cold-mixing investigation performed to supply combustor design information and to determine optimum normal fuel-injector configurations for a general scramjet swept-strut fuel injector. The experimental investigation was made with two swept struts in a closed duct at a Mach number of 4.4 and a nominal ratio of jet mass flow to air mass flow of 0.0295, with helium used to simulate hydrogen fuel. Four injector patterns were evaluated; they represented the range of hole spacing and the ratio of jet dynamic pressure to free-stream dynamic pressure. Helium concentration, pitot pressure, and static pressure in the downstream mixing region were measured to generate the contour plots needed to define the mixing-region flow field and the mixing parameters. Experimental results show that the fuel penetration from the struts was less than the predicted values based on flat-plate data; but the mixing rate was faster and produced a mixing length less than one-half that predicted.

Mcclinton, C. R.↗

NASA NTRS1991

Active flutter suppression - Control system design and experimental validation

The synthesis and experimental validation of an active flutter suppression controller for the Active Flexible Wing wind-tunnel model is presented. The design is accomplished with traditional root locus and Nyquist methods using interactive computer graphics tools and with extensive use of simulation-based analysis. The design approach uses a fundamental understanding of the flutter mechanism to formulate a simple controller structure to meet stringent design specifications. Experimentally, the flutter suppression controller succeeded in simultaneous suppression of two flutter modes, significantly increasing the flutter dynamic pressure despite errors in flutter dynamic pressure and flutter frequency in the mathematical model. The flutter suppression controller was also successfully operated in combination with a roll maneuver controller to perform flutter suppression during rapid rolling maneuvers.

Waszak, Martin R.↗

NASA NTRS2004

The O(+) Density Trough at 5000 km Altitude in the Polar Cap

At altitudes near 5000 km over the southern polar cap region of the terrestrial magnetosphere/ionosphere, the Thermal Ion Dynamics Experiment (TIDE) on board the Polar satellite has observed O(+) ion density trough regions, in which the densities were at least one order of magnitude lower than the surrounding O(+) densities. In the 0" density trough regions, the estimated O+ densities were generally lower than 0.01 per cc. The boundaries between normal density level regions and the trough density regions were usually abrupt transitions. From 1 December 1997 to 30 November 1998, polar cap O(+) troughs in Polar/TIDE observations occurred at a frequency of about 48%. Statistical examination of the Polar perigee observations from 1 December 1997 to 30 November 1998 shows that the Polar perigee passes evenly covered the southern polar cap region, while the O(+) density trough was always located on the nightside portion of the polar cap magnetosphere/ionosphere, and that invariant latitude spans of such troughs could be as large as 23 deg. in extent. The trough occurrence displayed a strong seasonal dependence; in the winter season (e.g., for July in the Southern Hemisphere) the O(+) ion density trough occurrence frequency ranged up to 92%, while in the summer season (e.g., for January in the Southern Hemisphere) it decreased to as low as 15%. Our statistical results show that the trough occurrence was generally anticorrelated with solar wind dynamic pressure in the solar wind dynamic pressure range 0.8 - 2.6 nanopascal. The O(+) ion density trough occurrence appeared relatively independent of the geomagnetic Kp index, IMF Bz, and By conditions. However, as suggested by the seasonal dependence, the O(+) ion density trough occurrence was strongly related to the solar zenith angle (SZA). In the SZA range 50 deg. to 125 deg., the trough occurrence increased monotonically with SZA. In addition, we sought to determine consistent density and velocity signatures at lower altitudes associated the O(+) ion density trough at 5000 km by examining the near-simultaneous O(+) densities and vertical velocities observed by the DMSP satellite group orbiting at 840 km altitude. However, consistent correlations between the dual altitudes were not reliably established from the present examinations.

Zeng, W.↗

NASA NTRS1960

Flight Measurement of Wall-Pressure Fluctuations and Boundary-Layer Turbulence

The results are presented for a flight test program using a fighter type jet aircraft flying at pressure altitudes of 10,000, 20,000, and 30,000 feet at Mach numbers from 0.3 to 0.8. Specially designed apparatus was used to measure and record the output of microphones and hot-wire anemometers mounted on the forward-fuselage section and wing of the airplane. Mean-velocity profiles in the boundary layers were obtained from total-pressure measurements. The ratio of the root-mean-square fluctuating wall pressure to the free-stream dynamic pressure is presented as a function of Reynolds number and Mach number. The longitudinal component of the turbulent-velocity fluctuations was measured, and the turbulence-intensity profiles are presented for the wing and forward-fuselage section. In general, the results are in agreement with wind-tunnel measurements which have been-reported in the literature. For example, the variation the square root of p(sup 2)/q times the square root of p(sup 2) is the root mean square of the wall-pressure fluctuation, and q is the free-stream dynamic pressure) with Reynolds number was found to be essentially constant for the forward-fuselage-section boundary layer, while variations at the wing station were probably unduly affected by the microphone diameter (5/8 in.), which was large compared with the boundary-layer thickness.

Mull, Harold R.↗

NASA NTRS1984

Investigation of the external flow analysis for density measurements at high altitude

The results of analysis performed on the external flow around the shuttle orbiter nose regions at the Shuttle Upper Atmosphere Mass Spectrometer (SUMS) inlet orifice are presented. The purpose of the analysis is to quantitatively characterize the flow conditions to facilitate SUMS flight data reduction and subsequent determination of orbiter aerodynamic force coefficients in the hypersonic rarefied flow regime. Experimental determination of aerodynamic force coefficients requires accurate simultaneous measurement of forces (or acceleration) and dynamic pressure along with independent knowledge of density and velocity. The SUMS provides independent measurement of dynamic pressure; however, it does so indirectly and requires knowledge of the relationship between measured orifice conditions and the dynamic pressure which can only be determined on the basis of molecule or theory for a winged configuration. Monte Carlo direct simulation computer codes were developed for both the flow field solution at the orifice and for the internal orifice flow. These codes were used to study issues associated with geometric modeling of the orbiter nose geometry and the modeling of intermolecular collisions including rotational energy exchange and a preliminary analysis of vibrational excitation and dissociation effects. Data obtained from preliminary simulation runs are presented.

Bienkowski, G. K.↗

NASA NTRS1960

Noise Considerations for Manned Reentry Vehicles

Noise measurements pertaining mainly to the static firing, launch, 0 and exit flight phases are presented for three rocket-powered vehicles 4 in the Project Mercury test program. Both internal and external data 4 from onboard recordings are presented for a range of Mach numbers and dynamic pressures and for different external vehicle shapes. The main sources of noise are noted to be the rocket engines during static firing and launch and the aerodynamic boundary layer during the high-dynamic-pressure portions of the flight. Rocket-engine noise measurements along the surface of the Mercury Big Joe vehicle were noted to correlate well with data from small models and available data for other large rockets. Measurements have indicated that the aerodynamic noise pressures increase approximately as the dynamic pressure increases and may vary according to the external shape of the vehicle, the highest noise levels being associated with conditions of flow separation. There is also a trend for the aerodynamic noise spectra to peak at higher frequencies as the flight Mach number increases.

Hilton, David A.↗

NASA NTRS2004

Nonlinear Oscillations and Flow of Gas Within Closed and Open Conical Resonators

A dissonant acoustic resonator with a conical shaped cavity was tested in four configurations: (A) baseline resonator with closed ends and no blockage; (B) closed resonator with internal blockage; (C) ventilated resonator with no blockage; and (D) ventilated resonator with an applied pressure differential. These tests were conducted to investigate the effects of blockage and ventilation holes on dynamic pressurization. Additionally, the investigation was to determine the ability of acoustic pressurization to impede flow through the resonator. In each of the configurations studied, the entire resonator was oscillated at the gas resonant frequency while dynamic pressure, static pressure, and temperature of the fluid were measured. In the final configuration, flow through the resonator was recorded for three oscillation conditions. Ambient condition air was used as the working fluid. The baseline results showed a marked reduction in the amplitude of the dynamic pressure waveforms over previously published studies due to the use of air instead of refrigerant as the working fluid. A change in the resonant frequency was recorded when blockages of differing geometries were used in the closed resonator, while acoustic pressure amplitudes were reduced from baseline measurements. A sharp reduction in the amplitude of the acoustic pressure waves was expected and recorded when ventilation ports were added. With elevated pressure applied to one end of the resonator, flow was reduced by oscillating the cavity at the fluid fundamental resonant frequency compared to cases without oscillation and oscillation off-resonance.

Daniels, Christopher↗

NASA NTRS2015

An Assessment of Combustion Dynamics in a Low-Nox, Second-Generation Swirl-Venturi Lean Direct Injection Combustion Concept

Dynamic pressure measurements were taken during flame-tube emissions testing of three second-generation swirl-venturi lean direct injection (SV-LDI) combustor configurations. These measurements show that combustion dynamics were typically small. However, a small number of points showed high combustion dynamics, with peak-to-peak dynamic pressure fluctuations above 0.5 psi. High combustion dynamics occurred at low inlet temperatures in all three SV-LDI configurations, so combustion dynamics were explored further at low temperature conditions. A point with greater than 1.5 psi peak-to-peak dynamic pressure fluctuations was identified at an inlet temperature of 450!F, a pressure of 100 psia, an air pressure drop of 3%, and an overall equivalence ratio of 0.35. This is an off design condition: the temperature and pressure are typical of 7% power conditions, but the equivalence ratio is high. At this condition, the combustion dynamics depended strongly on the fuel staging. Combustion dynamics could be reduced significantly without changing the overall equivalence ratio by shifting the fuel distribution between stages. Shifting the fuel distribution also decreased NOx emissions.

low emissions combustors↗

NASA NTRS1991

Optimal Control Problems with Switching Points

The main idea of this report is to give an overview of the problems and difficulties that arise in solving optimal control problems with switching points. A brief discussion of existing optimality conditions is given and a numerical approach for solving the multipoint boundary value problems associated with the first-order necessary conditions of optimal control is presented. Two real-life aerospace optimization problems are treated explicitly. These are altitude maximization for a sounding rocket (Goddard Problem) in the presence of a dynamic pressure limit, and range maximization for a supersonic aircraft flying in the vertical, also in the presence of a dynamic pressure limit. In the second problem singular control appears along arcs with active dynamic pressure limit, which in the context of optimal control, represents a first-order state inequality constraint. An extension of the Generalized Legendre-Clebsch Condition to the case of singular control along state/control constrained arcs is presented and is applied to the aircraft range maximization problem stated above. A contribution to the field of Jacobi Necessary Conditions is made by giving a new proof for the non-optimality of conjugate paths in the Accessory Minimum Problem. Because of its simple and explicit character, the new proof may provide the basis for an extension of Jacobi's Necessary Condition to the case of the trajectories with interior point constraints. Finally, the result that touch points cannot occur for first-order state inequality constraints is extended to the case of vector valued control functions.

Seywald, Hans↗

NASA NTRS2000

The Strategy for the Second Phase of Aerobraking Mars Global Surveyor

On February 19, 1999, the Mars Global Surveyor (MGS) spacecraft was able to propulsively establish its mapping orbit. This event followed the completion of the second phase of aerobraking for the MGS spacecraft on February 4, 1999. For the first time, a spacecraft at Mars had successfully employed aerobraking methods in order to reach its desired pre-launch mapping orbit. This was accomplished despite a damaged spacecraft solar array. The MGS spacecraft was launched on November 7, 1996, and after a ten month interplanetary transit was inserted into a highly elliptical capture orbit at Mars on September 12, 1997. Unlike other interplanetary missions, the MGS spacecraft was launched with a planned mission delta-V ((Delta)V) deficit of nearly 1250 m/s. To overcome this AV deficit, aerobraking techniques were employed. However, damage discovered to one of the spacecraft's two solar arrays after launch forced major revisions to the original aerobraking planning of the MGS mission. In order to avoid a complete structural failure of the array, peak dynamic pressure levels for the spacecraft were established at a major spacecraft health review in November 1997. These peak dynamic pressure levels were roughly one-third of the original mission design values. Incorporating the new dynamic pressure limitations into mission replanning efforts resulted in an 'extended' orbit insertion phase for the mission. This 'extended' orbit insertion phase was characterized by two distinct periods of aerobraking separated by an aerobraking hiatus that would last for several months in an intermediate orbit called the "Science Phasing Orbit" (SPO). This paper describes and focuses on the strategy for the second phase of aerobraking for the MGS mission called "Aerobraking Phase 2." This description will include the baseline aerobraking flight profile, the trajectory control methodology, as well as the key trajectory metrics that were monitored in order to successfully "guide' the spacecraft to its desired mapping orbit. Additionally, the actual aerobraking progress is contrasted to the planned aerobraking flight profile. (A separate paper will describe the navigation aspects of MGS aerobraking in detail.) Key to the success of the MGS mission is the delivery of the spacecraft to its final mapping orbit and the synergy the instrument complement provides to its scientific investigators when science data is returned from that orbit. The MGS mapping orbit is characterized as a low altitude, near-circular, near-polar orbit that is Sun-synchronous with the descending equatorial crossing at 2:00 AM local mean solar time (LMST).

Johnston, M. D.↗

NASA NTRS1989

Active flutter suppression using invariant zeros/eigensystem assignment

An active control law is synthesized to raise the flutter dynamic pressure boundary of an active flexible wing wind tunnel model. The multi-input/multi-output controller has a two-degree-of-freedom structure consisting of: (1) an output dynamic compensator selected to assign system invariant zeros to shape the multivariable root loci, and (2) an output gain feedback controller, based on eigensystem assignment theory, using the compensator augmented system to stabilize the flutter mode and optimize a specified performance index. Evaluation of a digital implementation of a constant gain controller in a general batch simulation of the system reveals that the feedback system is stable over a dynamic pressure range of 50-400 psf, indicating robustness of design to dynamic pressure variations.

Srinathkumar, S.↗

DOE OSTI2023

Dynamic high pressure phase transformation of ZrW 2 O 8

Phase transformations under high strain rates (dynamic compression) are examined in situ on ZrW 2 O 8 , a negative thermal expansion ternary ceramic displaying polymorphism. Amorphization, consistent with prior quasi-static measurements, was observed at a peak pressure of 3.0 GPa under dynamic conditions, which approximate those expected during fabrication. Evidence of partial amorphization was observed at lower pressure (1.8 GPa) that may be kinetically restrained by the short (<~150 ns) time scale of the applied high pressure. The impact of kinetics of pressure-induced amorphization from material fabrication methods is briefly discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗