Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dendrites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High-performance all-solid-state Li–S batteries enabled by an all-electrochem-active prelithiated Si anode

The development of all-solid-state Li–S batteries has been greatly impeded by dendrite growth and dendrite penetration, which are both related to the Li metal anode. As a compromised alternative, we report lithium silicide (Li x Si) as a dendrite-free and high-capacity anode with Li source. Here, the as-synthesized Li x Si is relatively soft, highly electronically conductive, and with a high Li diffusivity. These distinctive properties make Li x Si anode viable as an “all-electrochem-active” electrode (consisted of 100 wt.% Li x Si). Compared with the typical composite electrode, the all-electrochem-active electrode not merely maximizes the electrode-level energy density but also minimizes the electrolyte-related interfacial degradation. Li x Si symmetric cell demonstrates a reversible cycling at 4 mA cm –2 for over 320 h. Stress change and morphological evolution of the Li x Si electrode are investigated upon dealloying/alloying. When paired with a S cathode (active mass loading of 3 mg cm –2 ), Li x Si–S full cell shows a good cycling behavior over 500 cycles and rate performance (69% capacity retained at 1.2C) even at 25 °C.

25 ENERGY STORAGE↗
DOE OSTI2020

A New General Paradigm for Understanding and Preventing Li Metal Penetration through Solid Electrolytes

The use of lithium (Li) or sodium (Na) metal anodes together with highly ion-conductive solid electrolytes (SEs) could provide batteries with a step improvement in volumetric and gravimetric energy densities. Unfortunately, these SEs face significant technical challenges, in large part because Li and Na dendrites can penetrate through SEs, leading to short circuits. The ability of such a soft material (Li or Na metal) to penetrate through ceramic is surprising from the point of view of models widely used in the Li-battery field. We introduce a concept, new to the battery field, for preventing penetration of lithium dendrites through SEs by putting the SE surfaces into a state of residual compressive stress. For a sufficiently high compressive stress, cracks have difficulty forming, and cracks that do form are forced to close, inhibiting dendrite penetration. This approach is widely used to solve commercially important stress corrosion cracking problems in metals and static fatigue problems in ceramics and glasses (e.g., Gorilla Glass). However, the technique will not be useful for SEs if the Li-ion transport rate through a SE is substantially reduced when the SE is under compression. Our molecular dynamics calculations for Li-ion transport through a common SE demonstrate that the introduction of even very high residual compressive stresses (~10 GPa) has only a modest effect on Li-ion transport kinetics, suggesting that this approach is viable and capable of providing a new paradigm for developing high-performance and mechanically stable SEs.

25 ENERGY STORAGE↗
DOE OSTI2023

Surface grain refinement of casting A380 aluminum alloy by ultrasonic-assisted surface mechanical grinding treatment

A novel surface processing technique, ultrasonic-assisted surface mechnical grinding treatment (U-SMGT), was proposed and applied to modify the surface micriostructure of the casting aluminum alloy (A380). Comprehensive post-process chracterization techniques including 3D profilometry, optical microscope, scanning electric microscopy (SEM), and electron backscatter diffraction (EBSD) were carried out to investigate the surface morphology and microstructure of the processed region (PR). It was found that a surface layer of grain refinement with a thickness of about 50 µm was formed. In the as-received base material (BM), large clusters of dendritic eutectic phase with a size of approximately 20 µm were isolated by α-Al matrix. Nano-indentation tests showed that hardness of the eutectic and α-Al in the as-received BM was 2.15 GPa and 1.2 GPa respectively. After U-SMGT, the large dendritic eutectic phase was broken down into much fine particles with an average size of 0.57 µm. These fine particles were uniformly distributed into the α-Al matrix. Nano-indentation measurement exhibited a hardness of 2.27 GPa within the processed region. The overall high hardness in the processed region is a result of the pinning effect of uniformly distributed fine dendrites and grain refinement of Al-matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electrolyte design for Li metal-free Li batteries

Li metal, with the lowest thermodynamically achievable negative electrochemical potential and the highest specific capacity (3860 mAh g -1 ), is the ultimate anode choice for Li batteries. However, the highest reported Li plating/stripping Coulombic efficiency (CE) of 99.5% after extensive efforts is still too low for the Li metal-free (all the Li metal in cycling comes from cathode, without anode pre-lithiation) Li metal batteries. The low CE is attributed to both non-uniform Li plating/stripping on the lithiophobic Cu current collector and Li dendrite growth through lithiophilic organic–inorganic solid electrolyte interphase (SEI) formed in carbonate electrolytes. Here, we use a lithiophilic Bismuth graphite blend (Bi–Gr) substrate to replace lithiophobic Cu current collector to seed a uniform Li nucleation, and form a lithiophobic LiF-rich SEI rather than lithiophilic organic-rich SEI to suppress Li dendrite growth. Molecular dynamics simulations reveal the preferential reduction of anions in 2.0 M LiPF 6 in tetrahydrofuran/2-methyl tetrahydrofuran (2.0 M LiPF 6 –mixTHF) electrolyte to generate LiF-rich SEI on plated Li. Bi–Gr substrate and 2.0 M LiPF 6 –mixTHF electrolyte enable the Li anodes to achieve a record high CE of 99.83% at a high capacity of 1.0 mAh cm -2 and current of 0.5 mA cm -2 . The Bi particles serve as dispersed nucleation centers that promote uniform Li deposition with strong adhesion to the substrate to avoid dead Li, while the lithiophobic LiF-rich SEI promotes lateral Li growth and suppresses the vertical Li dendrite growth even at a high current density of 3.0 mA cm -2 and high areal capacities of 3.0 mAh cm -2 . The regulation of Li nucleation and growth enables the Li metal-free LiFePO 4 full cells to achieve 100 cycles at a practical areal capacity of >2.0 mAh cm -2 . This article highlights the benefits of simultaneous substrate design to improve Li nucleation and electrolyte design to promote lithiophobic SEI growth, enabling a promising and practical route Li metal-free Li metal batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and mechanical properties of hypoeutectic Al–6Ce–3Ni-0.7Fe (wt.%) alloy

Here, a hypoeutectic, Fe-modified Al–Ce–Ni alloy (Al–6Ce–3Ni-0.7Fe, wt.%) is studied in terms of microstructure, thermal stability, ambient temperature strengthening, and creep resistance. The as-cast microstructure consists of primary Al dendrites and interdendritic binary eutectic regions (Al–Al11Ce3 and/or Al–Al9(Fe,Ni)2), with micron/submicron lamellar spacing, depending on the location along the height of the ingot. The cast alloy exhibits excellent coarsening resistance at 400 °C, with mostly unchanged microstructure and microhardness after 6 weeks of aging, indicating good thermal stability of Al11Ce3 and Al9(Fe,Ni)2. Orowan strengthening and load transfer are identified as strengthening mechanisms at ambient and elevated temperature. A high volume fraction of the intermetallic phases (providing load transfer) and relatively coarse eutectic spacing (for modest Orowan strengthening) result in a moderate as-cast microhardness of 566 ± 32 MPa. Creep resistance at 300 and 350 °C is similar to a binary Al-12.5Ce eutectic alloy (with twice the Ce content) because of two countering effects: Al–6Ce–3Ni-0.7Fe shows a higher volume fraction of strengthening intermetallic phases, but it also exhibits a large fraction of primary Al dendrites which weaken the alloy. By contrast, the alloy, when laser-remelted at the surface, has a fully eutectic microstructure without primary aluminum dendrites achieved by high undercooling on solidification, with a refined network of eutectic phases that doubles the microhardness as compared to the cast alloy. Whereas coarsening is faster due to the shorter diffusion distances between the eutectic phases, hardness remains ~30% higher than the as-cast alloy after ~6 weeks aging at 400 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Friction stir processing on a strontium modified, thin-wall, vacuum-assisted high-pressure die-cast Aural-5 alloy to improve tensile and fatigue performance

Here, this study explores the application of friction stir processing (FSP) to enhance the material properties of Sr-modified Aural-5 alloy, with a focus on improved tensile and fatigue properties. Aural-5 is a well-known vacuum-assisted high-pressure die-cast (HPDC) Al-Si7-Mg alloy used in the automotive industry to reduce vehicle weight, enhance fuel efficiency, and lower carbon emissions. This alloy modifies its material chemistry with Sr for fine fibrous networks of eutectic silicon and manganese (Mn) to reduce die soldering. It has significantly less iron (Fe) content resulting in the elimination of detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. The initial microstructure of as-received HPDC Aural-5 exhibits shrinkage porosity in the middle section, a dendritic microstructure with fibrous Al-Si eutectic colonies, a shear-band structure beneath the die-wall, large dendritic externally solidified crystals (ESCs), needle-shaped Mg 2 Si phase and significant second-phase particulates. Some of those microstructural features, such as porosity, ESCs, needle-shaped Mg 2 Si phase, and large second-phase particles, serve as initiation sites for cracks under mechanical loading, resulting in adverse effects on tensile properties, particularly ductility. FSP effectively transforms the microstructure into a wrought configuration with uniform particle distribution by eliminating porosity and disintegrating dendrites, eutectic colonies, ESCs, second-phase particles, and shear-band structures. FSP-driven microstructure modification enhances yield strength and tensile ductility by ~30% and ~35%, respectively. The fatigue life of the material in a bending mode configuration (stress ratio R = 0.1) after FSP exhibits enhancements ranging from 2.0 to 3.9 times that of the original HPDC Aural-5 alloy, depending on the applied stress level.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Friction surface layer deposition of triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high entropy alloy: Process optimization and microstructural evolution

A high-strength Co-free triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high-entropy alloy (HEA) was successfully fabricated using Friction Surface Layer Deposition (FSLD), a bulk manufacturing method. Multiple single-layer deposits were produced by varying forging force (F) and traverse speeds (T r ) to optimize the process parameters. The optimized conditions (F = 40 kN & T r = 200 mm/min) were then applied to manufacture a scaled-up multi-layer specimen. The initial microstructure of the HEA consisted of coarse grains of the soft FCC-phase, long columnar dendrites of the hard BCC-phase, and small precipitates of the harder B2-phase within the BCC-dendrites. During FSLD, the FCC-matrix underwent continuous dynamic recrystallization due to high-temperature severe plastic deformation, forming finer equiaxed grains. Simultaneously, the BCC-dendrites fractured into smaller fragments, some of which experienced partial growth and coarsening under applied stress, resulting in an hourglass morphology. In contrast, the small B2-precipitates within the BCC-fragments dissolved during the elevated temperatures of FSLD and reprecipitated as substantially finer precipitates during continuous cooling post-FSLD. Additionally, the orientation relationships between the FCC and BCC/B2 phases were completely destroyed by the severe thermoplastic deformation inherent to FSLD. The microstructural refinements led to a substantial improvement in hardness from 177 HV to 283 HV, driven by Hall-Petch strengthening. The increased number of interfaces, including coherent BCC-B2 interfaces, potentially enhances the sink strength and radiation tolerance of the HEA, making it a promising candidate for nuclear applications. In conclusion, this study also highlights FSLD as a versatile technique for achieving tunable properties in HEAs, with detailed schematics illustrating the complex mechanisms of phase transformations during processing.

Additive Manufacturing↗
DOE OSTI2020

Deformation behavior of metallic glass composites and plasticity accommodation at microstructural length-scales

Bulk metallic glass matrix composites represent a unique microstructural design strategy for overcoming the strength/ductility trade-off in structural alloys. Site-specific mechanical behavior of a Ti-based bulk metallic glass composite was evaluated at microstructural length-scale. The micro-pillars on the amorphous matrix showed on average a yield point of 1.9 GPa followed by serrated plastic deformation characteristic of shear banding. In contrast, micro-pillars on the crystalline dendritic phase showed a much lower yield strength of 0.72 GPa on average for the four different crystallographic orientations chosen, smooth plastic flow with no recognizable load burst, and stable strain-hardening after yield point. A number of micro-pillars were made at the interface between the glassy matrix and the crystalline dendrite. The mixed micro-pillars showed homogeneous deformation and greater plasticity which was attributed to their smaller stored elastic energy. Shear bands initiated in the amorphous matrix were arrested by the crystalline dendrite, which accommodated plasticity through slip bands and dislocations pile-ups. The interface remained intact after plastic deformation, with no observable signs of devitrification in the amorphous phase.

Bulk metallic glass matrix composite, Micro-pillar↗
DOE OSTI2025

Crack mitigation and wear performance of high-strength steel coatings deposited by high-speed laser cladding

This article investigates the fabrication of defect-free Rockit® 606, a high‑carbon, vanadium- and chromium-enriched precipitation-hardening martensitic steel coating, using high-speed laser cladding (HSLC). Compared to conventional laser cladding, HSLC offers higher deposition efficiency, improved coating quality, minimal thermal distortion, and a reduced heat-affected zone. Various HSLC parameters—including laser power, travel speed, powder feed rate, and overlap distance—were optimized to achieve superior coating properties. Microstructural analysis revealed solidification cracks in coatings deposited on carburized steel, regardless of processing parameters. However, preheating the substrate to 250 °C effectively eliminated cracking by reducing thermal gradients. The coatings exhibited a columnar dendritic microstructure, with coarser dendrites near the substrate and finer dendrites towards the surface. Hardness measurements confirmed that all coatings significantly exceeded the industry-specified threshold of 60 HRC, with preheating having minimal effect on overall hardness distribution. Reciprocating sliding wear tests demonstrated a substantial improvement in wear resistance for the defect-free HSLC coatings compared to baseline carburized steel. These findings underscore the potential of HSLC for producing high-performance, wear-resistant coatings suitable for industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Maintaining a Flat Li Surface during the Li Stripping Process via Interface Design

Electroplating has been the main focus in mitigating the dendrite growth on the Li-metal electrode; however, the stripping process is equally critical, since the nonsmooth Li surface during stripping will lead to nonuniform local current density, planting the seeds for dendrite growth. In this paper, density functional theory (DFT) and kinetic Monte Carlo (KMC) techniques were combined to investigate the vacancy evolution in Li interfaced with different solid–electrolyte interphase (SEI) materials. It was found that the lithiophilic interface, such as Li/Li 2 O, repels vacancies into the bulk Li, so Li atoms can quickly fill the Li vacancies near the Li/Li 2 O interface and maintain a smooth Li surface. In contrast, the lithiophobic interface, such as Li/LiF, traps Li vacancies toward the interface, and the accumulated Li vacancies form voids and roughen the surface. The predicted critical stripping current density, below which a smooth Li surface will be maintained, is therefore much faster at the lithiophilic interface than that at the lithiophobic interface. It was further revealed that the lithiophilicity at different SEI or coating materials can be ranked as Li/Li 2 O > Li/LiPON > Li/Li 2 CO 3 > Li/LiF based on the calculated interfacial adhesion and accumulation of electron density at the interface. Furthermore, this suggests that interface and coating design at nanoscale can be effective for maintaining a smooth Li surface during the stripping process, solving another challenge to achieving a dendrite-free Li-metal electrode in both liquid and solid electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High Current Cycling in a Superconcentrated Ionic Liquid Electrolyte to Promote Uniform Li Morphology and a Uniform LiF-Rich Solid Electrolyte Interphase

High-energy-density systems with fast charging rates and suppressed dendrite growth are critical for the implementation of efficient and safe next-generation advanced battery technologies such as those based on Li metal. However, there are few studies that investigate reliable cycling of Li metal electrodes under high-rate conditions. in this work, by employing a superconcentrated ionic liquid (IL) electrolyte, we highlight the effect of Li salt concentration and applied current density on the resulting Li deposit morphology and solid electrolyte interphase (SEI) characteristics, demonstrating exceptional deposition/dissolution rates and efficiency in these systems. Operation at higher current densities enhanced the cycling efficiency, e.g., from 64 ± 3% at 1 mA cm –2 up to 96 ± 1% at 20 mA cm –2 (overpotential <±0.2 V), while resulting in lower electrode resistance and dendrite-free Li morphology. A maximum current density of 50 mA cm –2 resulted in 88 ± 3% cycling efficiency, displaying tolerance for high overpotentials at the Ni working electrode (0.5 V). X-ray photoelectron microscopy (XPS), time-of-flight secondary-ion mass spectroscopy (ToF-SIMS), and scanning electron microscopy (SEM) surface measurements revealed that the formation of a stable SEI, rich in LiF and deficient in organic carbon species, coupled with nondendritic and compact Li morphologies enabled enhanced cycling efficiency at higher currents. Reduced dendrite formation at high current is further highlighted by the use of a highly porous separator in coin cell cycling (1 mAh cm –2 at 50 °C), sustaining 500 cycles at 10 mA cm –2 .

25 ENERGY STORAGE↗
DOE OSTI2022

Suppressing electrolyte-lithium metal reactivity via Li + -desolvation in uniform nano-porous separator

Lithium reactivity with electrolytes leads to their continuous consumption and dendrite growth, which constitute major obstacles to harnessing the tremendous energy of lithium-metal anode in a reversible manner. Considerable attention has been focused on inhibiting dendrite via interface and electrolyte engineering, while admitting electrolyte-lithium metal reactivity as a thermodynamic inevitability. Here, we report the effective suppression of such reactivity through a nano-porous separator. Calculation assisted by diversified characterizations reveals that the separator partially desolvates Li + in confinement created by its uniform nanopores, and deactivates solvents for electrochemical reduction before Li 0 -deposition occurs. The consequence of such deactivation is realizing dendrite-free lithium-metal electrode, which even retaining its metallic lustre after long-term cycling in both Li-symmetric cell and high-voltage Li-metal battery with LiNi 0.6 Mn 0.2 Co 0.2 O 2 as cathode. The discovery that a nano-structured separator alters both bulk and interfacial behaviors of electrolytes points us toward a new direction to harness lithium-metal as the most promising anode.

25 ENERGY STORAGE↗
DOE OSTI2025

Understanding rate-dependent textured growth in zinc electrodeposition via high-throughput in situ x-ray diffraction

Zn-ion batteries with aqueous electrolytes are promising for large-scale energy storage as they are low-cost, environment-friendly and safe. The commercialization of Zn-ion batteries is hindered by several challenges such as the formation of detrimental Zn dendrites. High current density is previously thought to stimulate the dendritic growth of metals such as Li in electrodeposition. However, our study finds that for metallic Zn negative electrode in Zn-ion batteries, high-current deposition results in a dense and flat Zn layer with a (002) texture, which extends the cycling life. Low-current deposition, on the other hand, leads to a porous and dendritic morphology and a short cycling life. Using a synchrotron-based high-throughput in situ X-ray diffraction method we recently developed, Zn deposition under different conditions is systematically investigated, and a texture formation mechanism is proposed. Based on these findings, we suggest guidelines for designing cycling protocols that enable long-lasting Zn-ion batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Developing of nano sized fibrous eutectic silicon in hypereutectic Al–Si alloy by laser remelting

Laser surface melting followed by rapid solidification is an effective means to produce very fine microstructures with desirable surface properties because of the high rates of cooling associated with it. In the present study, the effect of rapid cooling on the silicon particle size, distribution, and morphology of hypereutectic Al–17wt.%Si and Al–20wt.%Si alloys have been investigated. A continuous-wave CO2 laser of wavelength 10.6 μm and a Trumpf Yb-YAG disk laser of wavelength 1.030 μm were used with a beam diameter of 1 mm and scanning speeds ranging from 5 to 100 mm/s. Rapid solidification increased the solubility of silicon in aluminum to approximately 5wt% and induced non-equilibrium hypoeutectic microstructures comprising large volume fractions of primary α-Al dendrites and ultrafine Al–Si eutectic of lamellar morphology. Both α-Al dendrites and the silicon particle sizes were significantly reduced from micron to nanoscale level. The morphology of silicon particles is modified from massive polygonal and plate-like to a mixture of fine fakes with round corners, feathery and fibrous, or a coral-like and thread-like structure. The eutectic silicon size and the interlamellar spacing were reduced to 30 and 10 nm, respectively. Furthermore, most of the silicon crystals in the eutectic region and the aluminum dendrites contained a significant number of twins which were considered as an essential contributor to the mechanism of growth and branching. Microhardness values increased two to threefold due to the refinement of the microstructural constituent.

42 ENGINEERING↗
DOE OSTI2024

Microstructural stability and mechanical properties of the as-cast and heat-treated newly developed TiNbCrTa refractory complex concentrated alloy

In this study, a TiNbCrTa refractory complex concentrated alloy (RCCA) was prepared using vacuum arc remelting. The microstructural evolution and mechanical properties of both as-cast and heat-treated RCCA samples were analyzed. Heat treatment (HT) was performed at 800–1200 °C for 1 h in a vacuum-sealed environment. These samples exhibited a formation of Cr 2 Nb and Cr 2 Ti Laves phases. A variation in elemental distribution was observed, with interdendritic (ID) regions showing higher fractions of Ti and Cr, while the dendritic regions had a greater concentration of Ta and Nb. Micro-segregation at the IDs was confirmed through energy dispersive x-ray spectroscopy mapping, which inferred the formation of Cr- and Ti-rich phases during HT at 800–1200 °C. High-temperature HT at 1200 °C for 1 h led to the evolution of the hcp omega phase. Prolonged HT at 1200 °C for 96 h resulted in the evolution of a Cr-rich Laves phase (Cr 2 Ta), which was homogeneously distributed within the microstructure, indicating an unstable microstructure. Furthermore, despite prolonged HT, a variation in the elemental distribution persisted due to the presence of dendritic and ID regions. Electron backscattered diffraction analysis revealed the presence of bcc and hcp phases in the dendritic and ID regions, respectively, of the as-cast and HTed samples. The as-cast samples demonstrated a high compressive strength of approximately 2 GPa. Micro-hardness values increased with the HT temperature up to 1000 °C. Further increases under HT conditions did not significantly reduce the microhardness value, whereas prolonged HT at 1200 °C led to an increase in the microhardness value. Overall, the newly developed TiNbCrTa RCCA exhibited high-strength behavior even after the phase transformation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Surface structure of mass-selected niobium oxide nanoclusters on Au(111)

The structures formed by the deposition of mass-selected niobium oxide clusters, Nb 3 O y ( y = 5, 6, 7), onto Au(111) were studied by scanning tunneling microscopy. The as-deposited Nb 3 O 7 clusters assemble into large dendritic structures that grow on the terraces as well as extend from the top and bottom of step edges. The Nb 3 O 6 cluster also forms dendritic assemblies but they are generally much smaller in size. The assemblies are composed of smaller discrete structures (<1 nm) which are likely to be single clusters. Furthermore, the dendritic assemblies for both the Nb 3 O 7 and Nb 3 O 6 clusters have fractal dimensions of about 1.7 which is very close to that expected for simple diffusion limited aggregation. Annealing the Nb 3 O 7,6 /Au(111) surfaces up to 550 K results in changes in assembly sizes and increases in heights, while heating to 700 results in the disruption of the assemblies into smaller structures. By contrast, the as-deposited Nb 3 O 5 /Au(111) surface at RT exhibits compact cluster structures which become 3D nanoparticles when annealed above 550 K. Differences in the observed surface structures and thermal stability are attributed to differences in metal-oxygen stoichiometry which can influence cluster binding energies, mobility and inter-cluster interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗