Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Degradation Rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

MODIS Aqua Optical Throughput Degradation Impact on Relative Spectral Response and Calibration on Ocean Color Products

Since Moderate Resolution Imaging Spectroradiometer Aqua's launch in 2002, the radiometric system gains of the reflective solar bands have been degrading, indicating changes in the systems optical throughput. To estimate the optical throughput degradation, the electronic gain changes were estimated and removed from the measured system gain. The derived optical throughput degradation shows a rate that is much faster in the shorter wavelengths than the longer wavelengths. The wavelength-dependent optical throughput degradation modulated the relative spectral response (RSR) of the bands. In addition, the optical degradation is also scan angle-dependent due to large changes in response versus the scan angle over time. We estimated the modulated RSR as a function of time and scan angles and its impacts on sensor radiometric calibration for the ocean science. Our results show that the calibration bias could be up to 1.8 % for band 8 (412 nm) due to its larger out-of-band response. For the other ocean bands, the calibration biases are much smaller with magnitudes at least one order smaller.

Lee, Shihyan↗
NASA NTRS2011

Feasibility of Orion Crew Module Entry on Half of Available Propellant Due to Tank Isolation Fault

The fuel tank isolation as a result of leak or rupture can leave an Orion Crew Module with only half of the loaded propellant for ISS return atmospheric entry. To assess the feasibility of returning under this condition, an analysis of various entry control options with deliberate degradation of control performance was performed. The study determined that a ballistic entry without a raise burn, a steeper flight path trajectory, relaxed atmospheric pitch/yaw rate damping, and degraded touchdown control could achieve 2-sigma requirements compliance with a 2-sigma fuel usage that is less than half of the liftoff propellant loading. The results of this analysis indicate that an entry with only half the nominal propellant load is feasible following a tank isolation fault.

Moen, Marina M.↗
NASA NTRS2009

An LED Approach for Measuring the Photocatalytic Breakdown of Crystal Violet Dye

A simple technique to assess the reactivity of photocatalytic coatings sprayed onto transmissive glass surfaces was developed. This new method uses ultraviolet (UV) gallium nitride (GaN) light-emitting diodes (LEDs) to drive a photocatalytic reaction (the photocatalytic breakdown of a UV-resistant dye applied to a surface coated with the semiconductor titanium dioxide); and then a combination of a stabilized white light LED and a spectrometer to track the dye degradation as a function of time. Simple, standardized evaluation techniques that assess photocatalytic materials over a variety of environmental conditions, including illumination level, are not generally available and are greatly needed prior to in situ application of photocatalytic technologies. To date, much research pertaining to this aspect of photocatalysis has been limited and has focused primarily on laboratory experiments using mercury lamps. Mercury lamp illumination levels are difficult to control over large ranges and are temporally modulated by line power, limiting their use in helping to understand and predict how photocatalytic materials will behave in natural environmental settings and conditions. The methodology described here, using steady-state LEDs and time series spectroradiometric techniques, is a novel approach to explore the effect of UV light on the photocatalytic degradation of a UV resistant dye (crystal violet). GaN UV LED arrays, centered around 365 nm with an adjustable DC power supply, are used to create a small, spatially uniform light field where the steady state light level can be varied over three to four orders of magnitude. For this study, a set of glass microscope slides was custom coated with a thinly sprayed layer of photocatalytic titanium dioxide. Crystal violet was then applied to these titanium-dioxide coated slides and to uncoated control slides. The slides were then illuminated at various light levels from the dye side of the slide by the UV LED array. To monitor dye degradation on the slides over time, a temperature-stabilized white light LED was used to illuminate the opposite side of the slides. As the dye degraded, the amount of light from the white light LED transmitted through the slide was monitored with a spectrometer and subsequently analyzed to determine and compare the rate of dye degradation for photocatalytically coated versus uncoated slide surfaces. The long-term stability of the spectrometer/white light LED combination, which required only a single reference spectra to be taken for a time series sequence of several hours, enabled accurate measurements of transmitted light over time. Time series transmission curves were generated and results demonstrated that over time the transmission increased much more rapidly on the coated slides than on the control slides. This experimental configuration and methodology for photocatalytic activity measurement minimizes many external variable effects and allows low light level studies to be performed. This study also compares the advantages of this novel LED light source design to traditional mercury lamp systems and non-LED lamp approaches that have conventionally been used. The methodology and experimental design research summarized in this abstract is partly funded by the Department of Homeland Security, Science and Technology Directorate, and by the NASA Stennis Space Center Innovative Partnerships Program.

Ryan, Robert E.↗
NASA NTRS2016

Hydrogen Embrittlement

Hydrogen embrittlement (HE) is a process resulting in a decrease in the fracture toughness or ductility of a metal due to the presence of atomic hydrogen. In addition to pure hydrogen gas as a direct source for the absorption of atomic hydrogen, the damaging effect can manifest itself from other hydrogen-containing gas species such as hydrogen sulfide (H2S), hydrogen chloride (HCl), and hydrogen bromide (HBr) environments. It has been known that H2S environment may result in a much more severe condition of embrittlement than pure hydrogen gas (H2) for certain types of alloys at similar conditions of stress and gas pressure. The reduction of fracture loads can occur at levels well below the yield strength of the material. Hydrogen embrittlement is usually manifest in terms of singular sharp cracks, in contrast to the extensive branching observed for stress corrosion cracking. The initial crack openings and the local deformation associated with crack propagation may be so small that they are difficult to detect except in special nondestructive examinations. Cracks due to HE can grow rapidly with little macroscopic evidence of mechanical deformation in materials that are normally quite ductile. This Technical Memorandum presents a comprehensive review of experimental data for the effects of gaseous Hydrogen Environment Embrittlement (HEE) for several types of metallic materials. Common material screening methods are used to rate the hydrogen degradation of mechanical properties that occur while the material is under an applied stress and exposed to gaseous hydrogen as compared to air or helium, under slow strain rates (SSR) testing. Due to the simplicity and accelerated nature of these tests, the results expressed in terms of HEE index are not intended to necessarily represent true hydrogen service environment for long-term exposure, but rather to provide a practical approach for material screening, which is a useful concept to qualitatively evaluate the severity of hydrogen embrittlement. The effects of hydrogen gas on mechanical properties such as tensile strength, ductility, fracture, low and high cycle fatigue, crack growth rate, and creep rupture are analyzed with respect to the general trends established from the HEE index values. It is observed that the severity of HE effects is also influenced by environmental factors such as pressure, temperature, and hydrogen gas purity. The severity of HE effects is also influenced by material factors such as surface finish, heat treatment, and product forms, compositions, grain direction, and crystal orientations.

Jonathan A. Lee↗
NASA NTRS2004

Solar Variability and the Near-Earth Environment: Mining Enhanced Low Dose Rate Sensitivity Data From the Microelectronics and Photonics Test Bed Space Experiment

This effort is a detailed analysis of existing microelectronics and photonics test bed satellite data from one experiment, the bipolar test board, looking to improve our understanding of the enhanced low dose rate sensitivity (ELDRS) phenomenon. Over the past several years, extensive total dose irradiations of bipolar devices have demonstrated that many of these devices exhibited ELDRS. In sensitive bipolar transistors, ELDRS produced enhanced degradation of base current, resulting in enhanced gain degradation at dose rates <0.1 rd(Si)/s compared to similar transistors irradiated at dose rates >1 rd(Si)/s. This Technical Publication provides updated information about the test devices, the in-flight experiment, and both flight-and ground-based observations. Flight data are presented for the past 5 yr of the mission. These data are compared to ground-based data taken on devices from the same date code lots. Information about temperature fluctuations, power shutdowns, and other variables encountered during the space flight are documented.

Turflinger, T.↗
NASA NTRSDate not supplied

Characterization of Photodegredation in Unsteady Pressure-Sensitive Paint Under Varying Pressures

The lifetime and intensity techniques are two distinct methods used to measure the surface pressure of wind tunnel models with pressure-sensitive paint (PSP). When exposed to 405 nm light for extended periods, both the luminescence and the lifetime ratio were observed to decrease, affecting perceived pressure values. To help further the implementation of the unsteady pressure-sensitive paint (uPSP), this paper describes the efforts to characterize how photo degradation affects the intensity of the paint signal and its lifetime ratio, as well as the intensity calibration's response and how these changes vary with different pressure environments. It was found that the paint photo degrades at different rates depending on the partial pressure of oxygen during excitation. It was also found that the calibration curves exhibit greater changes when exposed to excitation light in higher pressure environments, both indicating photo degradation due to photo decomposition and photo-oxidation processes. These effects are observed on models in a subsonic 14” × 14” wind tunnel as well as a large-scale 11’ x 11’ transonic wind tunnel. The work provides analysis into the photo degradation behavior of PSP and uPSP, paving the way to reduce the error in pressure measurements obtained through these techniques.

Pressure-Sensitive Paint↗
NASA NTRS1994

Advantages of estimating rate corrections during dynamic propagation of spacecraft rates: Applications to real-time attitude determination of SAMPEX

This paper describes real-time attitude determination results for the Solar, Anomalous, and Magnetospheric Particle Explorer (SAMPEX), a gyroless spacecraft, using a Kalman filter/Euler equation approach denoted the real-time sequential filter (RTSF). The RTSF is an extended Kalman filter whose state vector includes the attitude quaternion and corrections to the rates, which are modeled as Markov processes with small time constants. The rate corrections impart a significant robustness to the RTSF against errors in modeling the environmental and control torques, as well as errors in the initial attitude and rates, while maintaining a small state vector. SAMPLEX flight data from various mission phases are used to demonstrate the robustness of the RTSF against a priori attitude and rate errors of up to 90 deg and 0.5 deg/sec, respectively, as well as a sensitivity of 0.0003 deg/sec in estimating rate corrections in torque computations. In contrast, it is shown that the RTSF attitude estimates without the rate corrections can degrade rapidly. RTSF advantages over single-frame attitude determination algorithms are also demonstrated through (1) substantial improvements in attitude solutions during sun-magnetic field coalignment and (2) magnetic-field-only attitude and rate estimation during the spacecraft's sun-acquisition mode. A robust magnetometer-only attitude-and-rate determination method is also developed to provide for the contingency when both sun data as well as a priori knowledge of the spacecraft state are unavailable. This method includes a deterministic algorithm used to initialize the RTSF with coarse estimates of the spacecraft attitude and rates. The combined algorithm has been found effective, yielding accuracies of 1.5 deg in attitude and 0.01 deg/sec in the rates and convergence times as little as 400 sec.

Challa, M. S.↗
NASA NTRS1977

Nylon separators

A nylon separator was placed in a flooded condition in K0H solution and heated at various high temperatures ranging from 60 C to 110 C. The weight decrease was measured and the molecular weight and decomposition product were analyzed to determine: (1) the effect of K0H concentration on the hydrolysis rate; (2) the effect of K0H concentration on nylon degradation; (3) the activation energy at different K0H concentrations; and (4) the effect of oxygen on nylon degradation. The nylon hydrolysis rate is shown to increase as K0H concentration is decreased 34%, giving a maximum rate at about 16%. Separator hydrolysis is confirmed by molecular weight decrease in age of the batteries, and the reaction of nylon with molecular oxygen is probably negligible, compared to hydrolysis. The extrapolated rate value from the high temperature experiment correlates well with experimental values at 35 degrees.

Lim, H. S.↗
NASA NTRS1995

The coupling of fluids, dynamics, and controls on advanced architecture computers

This grant provided for the demonstration of coupled controls, body dynamics, and fluids computations in a workstation cluster environment; and an investigation of the impact of peer-peer communication on flow solver performance and robustness. The findings of these investigations were documented in the conference articles.The attached publication, 'Towards Distributed Fluids/Controls Simulations', documents the solution and scaling of the coupled Navier-Stokes, Euler rigid-body dynamics, and state feedback control equations for a two-dimensional canard-wing. The poor scaling shown was due to serialized grid connectivity computation and Ethernet bandwidth limits. The scaling of a peer-to-peer communication flow code on an IBM SP-2 was also shown. The scaling of the code on the switched fabric-linked nodes was good, with a 2.4 percent loss due to communication of intergrid boundary point information. The code performance on 30 worker nodes was 1.7 (mu)s/point/iteration, or a factor of three over a Cray C-90 head. The attached paper, 'Nonlinear Fluid Computations in a Distributed Environment', documents the effect of several computational rate enhancing methods on convergence. For the cases shown, the highest throughput was achieved using boundary updates at each step, with the manager process performing communication tasks only. Constrained domain decomposition of the implicit fluid equations did not degrade the convergence rate or final solution. The scaling of a coupled body/fluid dynamics problem on an Ethernet-linked cluster was also shown.

Atwood, Christopher↗
NASA NTRS1977

A study of the chemical degradation of ClONO2 in the stratosphere

The flash photolysis-resonance fluorescence system described by Davis et al. (1974) is used to measure the rate constants for the reactions of chlorine nitrate (ClONO2) with stratospheric O(3-P) and OH. Both reactions are examined in a pyrex cell with an internal volume of about 150 cu cm, where the reaction mixture was maintained at 245 K by circulating methanol from a thermostated circulation bath through the outer jacket of the reaction cell. The relative chemical degradation rates as a function of altitude for both reactions are tabulated, which shows that the chemical degradation pathways contribute less than 10% to the total rate of ClONO2 destruction at altitudes less than 30 km. Since the concentration of ClONO2 is calculated to be near its maximum around 25 km and drops off very significantly at higher altitudes, it is concluded that the photochemical decomposition of ClONO2 in the stratosphere is by far the most important degradation path for this molecule.

Ravishankara, A. R.↗
NASA NTRS1991

Pi/4-QPSK modems for satellite sound/data broadcast systems

The use of pi/4-quadrature phase-shift keying (QPSK) modems for satellite sound broadcast systems (SSBS) broadcasting to mobile or portable receivers is proposed. Three different differential detectors (including the FM-discriminator followed by integrate-sample-and-dump filter) and a novel coherent detector are discussed. The degradation caused by the frequency offset between the local oscillator (LO) and the unmodulated carrier (CR) in the baseband differential detector is studied. The performance of both coherently and differentially detected pi/4-QPSK in a Gaussian channel is also studied. It is shown that with a frequency offset of more than 3 percent of the symbol rate, the performance degradation is more than 1 dB at 0.0001. The out-of-band power of the nonlinearly amplified bandlimited pi/4-QPSK signals is reduced from -13 dB to -37 dB if a 2-dB output back-off amplifier is used instead of a hardlimiter. The performance of the pi/4-QPSK is equivalent to that of QPSK, although the pi/4-QPSK has the advantage of less spectrum restoration after nonlinear amplification. The coherent demodulator and differential decoder avoid the three-level detection and achieve the same bit-error-rate performance as DEQPSK with a simple circuit.

Liu, Chia-Liang↗
NASA NTRS1987

A study of the effect of group delay distortion on an SMSK satellite communications channel

The effects of group delay distortion on an SMSK satellite communications channel have been investigated. Software and hardware simulations have been used to determine the effects of channel group delay variations with frequency on the bit error rate for a 220 Mbps SMSK channel. These simulations indicate that group delay distortions can significantly degrade the bit error rate performance. The severity of the degradation is dependent on the amount, type, and spectral location of the group delay distortion.

Kerczewski, Robert J.↗
NASA NTRSDate not supplied

Degradation Characterization of Unsteady Pressure-Sensitive Paint Under Various Pressures

The lifetime and intensity techniques are two distinct methods used to measure the surface pressure of wind tunnel models with pressure-sensitive paint (PSP). When exposed to 405 nm light for extended periods, both the luminescence and the lifetime ratio were observed to decrease, affecting perceived pressure values. To help further the implementation of the uPSP, this paper describes the efforts to characterize the degradation of both the intensity of the paint and its lifetime ratio, as well as the change in intensity calibration. It was found that the paint degrades at different rates depending on the partial pressure of oxygen during excitation. It was also found that the calibration curves exhibit greater changes when under higher oxygen concentrations, both indicating photodegradation due to photodecomposition and photo-oxidation processes. These effects are observed on models in a subsonic 14” × 14” wind tunnel. The work provides insight into the dynamic degradation behavior of PSP and uPSP, paving the way to reduce the error in pressure measurements obtained through these techniques.

Pressure-Sensitive Paint↗
NASA NTRS1993

A high specific power solar array for low to mid-power spacecraft

UltraFlex is the generic term for a solar array system which delivers on-orbit power in the 400 to 6,000 watt per wing sizes with end-of-life specific power performance ranging to 150 watts-per-kilogram. Such performance is accomplished with off-the-shelf solar cells and state-of the-art materials and processes. Much of the recent work in photovoltaics is centered on advanced solar cell development. Successful as such work has been, no integrated solar array system has emerged which meets NASA's stated goals of 'increasing the end-of-life performance of space solar cells and arrays while minimizing their mass and cost.' This issue is addressed; namely, is there an array design that satisfies the usual requirements for space-rated hardware and that is inherently reliable, inexpensive, easily manufactured and simple, which can be used with both advanced cells currently in development and with inexpensive silicon cells? The answer is yes. The UltraFlex array described incorporates use of a blanket substrate which is thermally compatible with silicon and other materials typical of advanced multi-junction devices. The blanket materials are intrinsically insensitive to atomic oxygen degradation, are space rated, and are compatible with standard cell bonding processes. The deployment mechanism is simple and reliable and the structure is inherently stiff (high natural frequency). Mechanical vibration modes are also readily damped. The basic design is presented as well as supporting analysis and development tests.

Jones, P. Alan↗
NASA NTRSDate not supplied

Evaluation of Automotive Grade Resistors for Space Flight

Over the past decade, electronic, electrical, and electromechanical (EEE) parts for space applications have undergone significant changes, largely driven by CubeSat and commercial space developers pushing the boundaries on the utilization of commercial parts in space. Global product shortages and shipping delays are still impacting space flight project deadlines. Many projects have turned to automotive grade resistors as an alternate to their MILSPEC counterparts to fulfill requirements. In addition, automotive grade resistors may offer designers a wider range of parts to consider. A recent NASA study recommended the use of high-volume manufactured commercial components for space applications provided these components show evidence of stringent fabrication controls and thorough reliability monitoring practices. Automotive grade components have stringent qualification requirements per the Automotive Electronic Council (AEC). However, the end user usually does not have insight into the practices the manufacturer may use to reduce/eliminate infant mortality nor for compliance to all datasheet specifications. Screening, Life and Accelerated Life testing on a set of standard automotive-grade chip resistors is proposed to evaluate the reliability of these components. Requirements from both the AEC-Q (Automotive Electronic Council Qualification) and EEE-INST-002 (Instructions for EEE Parts Selection, Screening, Qualification, and Derating) for resistors is compared and discussed. The resistors have been tested by using a modified methodology from EEEINST-002 to evaluate their reliability for space flight projects. The findings of this study indicate that the underlying degradation mechanisms at rated temperature and power are best represented by power law models with a fitted exponent between 0 and 1. A linear model is more conservative which compensates for potential model uncertainty given the wide range of design and materials used in automotive resistors, while still providing useful long-term resistance drift estimates. No electrical anomalies or failures were observed throughout the 1000-hour Life Tests other than small in tolerance resistance drift aging. Degradation models were utilized to quantify and extrapolate the long-term resistance drift under operating conditions for the components. The models demonstrated that some automotive-grade resistors are likely to operate 10 years at nominal usage conditions while others might fail earlier.

Zainab Abdullahi↗
NASA NTRSDate not supplied

Evaluation of Automotive Grade Resistors for Space Flight

Over the past decade, electronic, electrical, and electromechanical (EEE) parts for space applications have undergone significant changes, largely driven by CubeSat and commercial space developers pushing the boundaries on the utilization of commercial parts in space. Global product shortages and shipping delays are still impacting space flight project deadlines. Many projects have turned to automotive grade resistors as an alternate to their MIL-SPEC counterparts to fulfill requirements. In addition, automotive grade resistors may offer designers a wider range of parts to consider. A recent NASA study recommended the use of high-volume manufactured commercial components for space applications provided these components show evidence of stringent fabrication controls and thorough reliability monitoring practices [1]. Automotive grade components have stringent qualification requirements per the Automotive Electronic Council (AEC). However, the end user usually does not have insight into the practices the manufacturer may use to reduce/eliminate infant mortality nor for compliance to all datasheet specifications. Screening, Life and Accelerated Life testing on a set of standard automotive-grade chip resistors is proposed to evaluate the reliability of these components. Requirements from both the AEC-Q (Automotive Electronic Council Qualification) and EEE-INST-002 (Instructions for EEE Parts Selection, Screening, Qualification, and Derating) for resistors is compared and discussed. The resistors have been tested by using a modified methodology from EEE-INST-002 to evaluate their reliability for space flight projects. The findings of this study indicate that the underlying degradation mechanisms at rated temperature and power are best represented by power law models with a fitted exponent between 0 and 1. A linear model is more conservative which compensates for potential model uncertainty given the wide range of design and materials used in automotive resistors, while still providing useful long-term resistance drift estimates. No electrical anomalies or failures were observed throughout the 1,000-hour Life Tests other than small in tolerance resistance drift aging. Degradation models were utilized to quantify and extrapolate the long-term resistance drift under operating conditions for the components. The models demonstrated that some automotive-grade resistors are likely to operate 10 years at nominal usage conditions while others might fail earlier.

Zainab Abdullahi↗
NASA NTRS1990

A robust CELP coder with source-dependent channel coding

A CELP coder using Source Dependent Channel Encoding (SDCE) for optimal channel error protection is introduced. With SDCE, each of the CELP parameters are encoded by minimizing a perceptually meaningful error criterion under prevalent channel conditions. Unlike conventional channel coding schemes, SDCE allows for optimal balance between error detection and correction. The experimental results show that the CELP system is robust under various channel bit error rates and displays a graceful degradation in SSNR as the channel error rate increases. This is a desirable property to have in a coder since the exact channel conditions cannot usually be specified a priori.

Sukkar, Rafid A.↗
NASA NTRS1996

Mass Wasting and Ground Collapse in Terrains of Volatile-Rich Deposits as a Solar System-Wide Geological Process: The Pre-Galileo View

The polar terrains of Mars are covered in many places with irregular pits and retreating scarps, as are some of the surfaces of the outer-planet satellites. These features are interpreted by us as diagnostic of exogenic degradation due to the loss of a volatile rock-forming matrix or cement. In this study we propose that sublimation degradation is a plausible Solar Systemwide geological process. Candidate examples have been identified on Mars, Io, and Triton, and possibly Europa and Ganymede. We envision this process as having two end-member expressions (pits and scarps), for which we hypothesize two end-member mechanisms (massive localized lenses and areally extensive basal layers). In this study we focus on the role this process may play on the surfaces of the galilean satellites. Our principle modeling results are that for these satellites, H2S, CO2, and NH3 are the only viable candidate volatiles for sublimation degradation of landforms, in light of galilean satellite cosmochemistry. For Io's polar regions only H2S, and then only from slopes that face the Sun and have thin lags, is volatile enough to cause the observed sublimation-induced erosion at those latitudes. SO2 is not a viable candidate as an agent of erosion, especially for these polar landforms. In the case of Europa, only CO2 and H2S are viable candidates (given surface age constraints). Both species could be efficient eroders in nonpolar regions. H2S could generate erosion within the polar regions if the deposition and erosion conditions were essentially identical as those we invoked for Io's polar regions. For Ganymede (and Callisto) NH3 might be an agent of erosion in equatorial terrains of great age. The sublimation of CO2 and H2S is much more robust than NH3. The much slower rate of sublimation degradation from NH3 might be detectable by Galileo and used as a compositional indicator.

Moore, Jeffrey M.↗