Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Damping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Damping in ring seals for compressible fluids

An analysis is presented to calculate damping in ring seals for a compressible fluid. Results show that damping in tapered ring seals (optimized for stiffness) is less than that in straight bore ring seals for the same minimum clearance. Damping in ring seals can promote fractional frequency whirl and can, thus, be detrimental. Thus, tapered seals can benefit rotor and seal stability by having lower damping as well as higher stiffness. Use of incompressible results leads to large errors.

Fleming, D. P.↗
NASA NTRS1980

Passive nutation damping using large appendages with application to Galileo

The use of large appendages for passive nutation damping is analyzed, and an analytical expression is developed to predict the nutation damping time constants for a large class of spacecraft including Galileo. It is shown that the use of large appendages for nutation damping can significantly degrade spacecraft stability margins and that the final design of the nutation damper must represent a tradeoff between the damping performance and the stability margin for sufficiently large appendages. The time constant derivation is outlined and the Galileo design is presented, including tradeoffs.

Bernard, D. E.↗
NASA NTRS1981

Measurements of Aerodynamic Damping in the MIT Transonic Rotor

A method was developed and demonstrated for the direct measurement of aerodynamic forcing and aerodynamic damping of a transonic compressor. The method is based on the inverse solution of the structural dynamic equations of motion of the blade disk system in order to determine the forces acting on the system. The disturbing and damping forces acting on a given blade are determined if the equations of motion are expressed in individual blade coordinates. If the structural dynamic equations are transformed to multiblade coordinates, the damping can be measured for blade disk modes, and related to a reduced frequency and interblade phase angle. In order to measure the aerodynamic damping in this way, the free response to a known excitation is studied.

Crawley, E. F.↗
NASA NTRS1982

Squeeze-Film-Damped Spring for Turbopumps

New use for squeeze-film damping proposed for turbopump bearings. Damping of axial shaft vibrations improved with properly-designed squeeze-film spring. Capillary-squeeze-film springs damp turbopump shaft axial vibrations. Disks deflect to left and right as pump bearing vibrates. Fluid fills and empties from spaces between disks to damp vibration.

Rothe, K.↗
NASA NTRS1982

Outgassing: Its effects on spacecraft. Vibration damping materials

The correlation of outgassing to the stability of the damping properties of polymer materials to be used in spacecraft structures is discussed. A test series was devised to obtain basic information from off-the-shelf damping materials. The test results could be considered as a guideline toward the application of these materials. Eight materials were selected to form a representative cross section of those polymers having both ready availability as commercial damping materials and desirable properties. A table indicates the temperatures at which peak damping occurs at 1 Hz and the type of beam specimen used in the vacuum exposure tests. These materials as a group cover the temperature range of -85 C to 38 C.

Drake, M. L.↗
NASA NTRS1982

Rotorcraft Blade Mode Damping Identification from Random Responses Using a Recursive Maximum Likelihood Algorithm

An on line technique is presented for the identification of rotor blade modal damping and frequency from rotorcraft random response test data. The identification technique is based upon a recursive maximum likelihood (RML) algorithm, which is demonstrated to have excellent convergence characteristics in the presence of random measurement noise and random excitation. The RML technique requires virtually no user interaction, provides accurate confidence bands on the parameter estimates, and can be used for continuous monitoring of modal damping during wind tunnel or flight testing. Results are presented from simulation random response data which quantify the identified parameter convergence behavior for various levels of random excitation. The data length required for acceptable parameter accuracy is shown to depend upon the amplitude of random response and the modal damping level. Random response amplitudes of 1.25 degrees to .05 degrees are investigated. The RML technique is applied to hingeless rotor test data. The inplane lag regressing mode is identified at different rotor speeds. The identification from the test data is compared with the simulation results and with other available estimates of frequency and damping.

Molusis, J. A.↗
NASA NTRS1982

Aerodynamic damping measurements in a transonic compressor

A method has been developed and demonstrated for the direct measurement of aerodynamic damping in a transonic compressor. The method is based on the inverse solution of the structural dynamic equations of motion of the blade-disk system. The equations are solved inversely to determine the forces acting on the system. If the structural dynamic equations are transformed to multiblade or modal coordinates, the damping can be measured for blade-disk modes, and related to a reduced frequency and interblade phase angle. This method of damping determination was demonstrated using a specially instrumented version of the MIT Transonic Compressor run in the MIT Blowdown Compressor Test Facility. No regions of aeroelastic instability were found. In runs at the operating point, the rotor was aerodynamically excited by a controlled two-per-revolution fixed up-stream disturbance. The disturbance was sharply terminated midway through the test. Analysis of the data in terms of multiblade modes led to a direct measurement of aerodynamic damping for three interblade phase angles.

Crawley, E. F.↗
NASA NTRS1982

Experimental measurement of passive material and structural damping for flexible space structures

Among the design objectives for large space structures are the maintenance of tight dimensional tolerance and the reduction of settling time after disturbance input. Two options are under consideration for the design of flexible structures to meet these objectives, including an active control option and a passive control option. In connection with both options, it is necessary to include material and structural damping in the design. A description is presented of the results of an experimental investigation of the damping of metallic and fibrous composite materials, taking into account also the analytical modeling and experimental verification of frictional damping schemes. To demonstrate how material and frictional damping can be combined, a simple structural optimization is performed, indicating the potential for significant savings in mass by the addition of frictional dampers.

Crawley, E. F.↗
NASA NTRS1982

Study of the damping characteristics of general aviation aircraft panels and development of computer programs to calculate the effectiveness of interior noise control treatment, part 1

Tests were carried out on 20 inch x 20 inch panels at different test conditions using free-free panels, clamped panels, and panels as installed in the KU-FRL acoustic test facility. Tests with free-free panels verified the basic equipment set-up and test procedure. They also provided a basis for comparison. The results indicate that the effect of installed panels is to increase the damping ratio at the same frequency. However, a direct comparison is not possible, as the fundamental frequency of a free-free panel differs from the resonance frequency of the panel when installed. The damping values of panels installed in the test facility are closer to the damping values obtained with fixed-fixed panels. Effects of damping tape, stiffeners, and bonded and riveted edged conditions were also investigated. Progress in the development of a simple interior noise level control program is reported.

Navaneethan, R.↗
NASA NTRS1983

Modeling global structural damping in trusses using simple continuum models

Truss beams with members having viscous damping are modeled as continuum Timoshenko beams. Procedures for deriving the equivalent beam stiffnesses and damping are presented. The global damping for the continuum beam is explicitly expressed in terms of the damping coefficients of the individual truss members. The continuum beam model is used to study transient vibration problems and the solutions are compared well with the full scale finite element solutions. The gradient method is used for parameter estimations in conjunction with the Timoshenko beam model. It is shown that the Timoshenko beam model can be easily updated with measured data and the updated model can yield very accurate transient solutions.

Sun, C. T.↗
NASA NTRS1983

Damping mechanisms in fiber reinforced laminates

Low strain damping in fiber reinforced composite materials is due to material loss factors in both fibers and matrix materials. The high modulus of the fibers makes up for the low damping factor. Strains high enough to cause transverse layer cracking in laminates with organic matrix materials causes a large permanent increase in the damping factor. This increase is not due to the transverse cracks but rather to short microcracks in the high shear strain regions. Other damping mechanisms at high strains are also discussed.

Plunkett, R.↗
NASA NTRS1985

Finite Element Prediction of Loss Factors for Structures with Frequency-dependent Damping Treatments

A finite element procedure is described for calculating the loss factors for elastic structures to which frequency-dependent viscoelastic damping treatments were applied. The frequency dependence of the viscoelastic damping material is treated by approximating its shear modulus with a second-order polynomial so that the stiffnesses associated with the constant, linear, and quadratic terms can be combined, respectively, with the stiffness, damping, and mass matrices assembled for the rest of the structure. A single complex eigenvalue analysis is then performed in which the eigenvalues are purely imaginary. The loss factor is computed by the modal strain energy (MSE) approach. In the the MSE approach, the loss factor of a composite structure vibrating in one of its natural modes may be visualized as a weighted average of the loss factors of the component parts, with the relative stored energies as weighting constants. The finite element procedure, which can treat very general geometries, is illustrated for the case of a vibrating constrained-layer damped plate.

Everstine, G. C.↗
NASA NTRS1985

Measurement of damping of graphite expoxy materials

During this period damping measurements were made on the cylindrical graphite epoxy specimen using the forced-vibration test method. The specimen was carefully mounted directly on the shaker through the supporting ring and the impedance head. This was done to simulate an idealized free-free boundary condition at the two edges. The damping ratio value and the natural frequency (first mode) obtained in this experiment were 0.13% and 508.75 Hz respectively. In order to check the damping induced by the supporting ring, measurements were made with the top half of the ring removed. The specimen then was supported only by the bottom half of the ring (half ring). It was observed that the natural frequency of the specimen (first mode) increased of a value of 552.5 Hz due to the influence of the reduced mass of the supporting ring. But the damping ratio value obtained was the same as that obtained with full supporting ring, namely 0.13%.

Crocker, M. J.↗
NASA NTRS1985

Influence of damping on quantum interference - An exactly soluble model

This paper reports the result of a calculation which shows the effect of damping on the quantum interference of two Gaussian wave packets in a harmonic potential. The influence-functional method, which seems to be the most appropriate one for this kind of calculation, is used. It is shown that quantum-interference effects are severely diminished by the presence of damping even when its influence on the system is only light. The corrections to the undamped formulas are always expressible in terms of the phenomenological damping constant, the temperature (in the high-temperature limit), the cutoff frequency of the reservoir oscillators, and the mean number of quanta of energy intially present in the system. Both weakly and strongly damped systems are analyzed in the regime of low and high temperatures.

Caldeira, A. O.↗
NASA NTRS1984

Concepts and effects of damping in isolators

A series of innovative designs and inventions which led to the solution of many aerospace vibration and shock problems through damping techniques is presented. The design of damped airborne structures has presented a need for such creative innovation. The primary concern was to discover what concepts were necessary for good structural damping. Once these concepts are determined and converted into basic principles, the design of hardware follows. The following hardware and techniques were developed in support of aerospace program requirements: shipping containers, alignment cables for precision mechanisms, isolation of small components such as relays and flight instruments, isolation for heavy flight equipment, coupling devices, universal joints, use of wire mesh to replace cable, isolation of 16-dB, 5000 lb horn, and compound damping devices to get better isolation from shock and vibration in a high steady environment.

Kerley, J.↗
NASA NTRS1985

A study on radiative damping of planetary waves utilizing stratospheric observations

Satellite ozone observations made by the Stratospheric Aerosol and Gas Experiment (SAGE) and corresponding meteorological temperature data are used to study the radiative damping processes associated with planetary waves during stratospheric warmings. Ramanathan's model has been adapted for the radiative heating and cooling calculations. The derived infrared damping coefficients, based on observed stratospheric ozone and temperature, are compared with the Newtonian cooling coefficients of Dickinson and Fels. It is also shown that the negative correlation between temperature and ozone solar heating in the upper stratosphere accelerates the damping rate due to infrared cooling alone, in agreement with the theoretical analysis and an earlier report based on observations. In addition, it is also found in this analysis that the phase relationship between ozone and solar heating waves is characterized by its behavior in three distinct layers. In the regions above about 2 mb and also below about 10 mb, the waves are closely in-phase. Between approximately 2 and 10 mb, they show a departure from the in-phase relationship which can be attributed to the so-called 'opacity effect'. This effect significantly determines the magnitude of radiative damping.

Ghazi, A.↗
NASA NTRS1986

Discrete mechanism damping effects in the solar array flight experiment

Accelerometer data were collected during on-orbit structural dynamic testing of the Solar Array Flight Experiment aboard the Space Shuttle, and were analyzed at Lockheed Missile and Space Co. to determine the amount of damping present in the structure. The results of this analysis indicated that the damping present in the fundamental in-plane mode of the structure substantially exceeded that of the fundamental out-of-plane mode. In an effort to determine the source of the higher in-plane damping, a test was performed involving a small device known as a constant-force spring motor or constant-torque mechanism. Results from this test indicate that this discrete device is at least partially responsible for the increased in-plane modal damping of the Solar Array Flight Experiment structure.

Pinson, E. D.↗
NASA NTRS1986

A study of the damping capacity of graphite epoxy composites in a vacuum

The damping properties of a graphite epoxy composite material (used in the construction of the Hubble Space Telescope) are measured under a variety of conditions in a vacuum chamber to simulate conditions in space. An improved method is proposed which utilizes several points of the response curve near a resonance to estimate the damping ratio and the undamped resonance frequency. The damping of a graphite epoxy tube is monitored for four weeks to study moisture desorption and temperature effects. A significant variation is observed in the damping ratio with temperature.

Rao, Mohan D.↗