Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cycle Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

New Thermochemical Salt Hydrate System for Energy Storage in Buildings

This paper introduces an innovative design for an “inorganic salt-expanded graphite” composite thermochemical system. The storage unit is made of a perforated, compressed, expanded graphite block impregnated with molten CaCl 2 ∙6H 2 O; the humid air passes through the holes that allow the moisture to diffuse and react with the salt. The prepared block underwent 90 hydration-dehydration cycles. Although most of the performed cycles were carried out with salt overhydration and deliquescence, the treated samples have remained mechanically and thermally stable with no drop in energy density. The volumetric energy density of the composite ranged from 135.5 to 277.6 kWh/m 3 , depending on airflow rate and absolute humidity. To ensure composite material cycling stability, the energy density of the block was measured during hydration at similar conditions of absolute humidity, inlet temperature, and airflow rate (0.01 kg water /kg air , 20 °C, 400 l/min). The average energy density at these conditions was sustained at 219 kWh/m 3 . The block integrity was monitored by visual inspection after removing it from the reactor chamber every few cycles. Both the composite material and its manufacturing process are simple and easy to scale up for future commercialization.

25 ENERGY STORAGE↗

Analysis of fuel cycle strategies and U.S. transition scenarios

The nuclear fuel cycle Evaluation and Screening (E&S) study that was completed in October 2014 [1] enabled the identification of four fuel cycle groups that are considered most promising based on a set of nine evaluation criteria: (a) six benefit criteria of Nuclear Waste Management, Proliferation Risk, Nuclear Material Security Risk, Safety, Environmental Impact, Resource Utilization, and (b) three challenge criteria of Development and Deployment Risk, Institutional Issues, Financial Risk and Economics. The E&S study was conducted at a level of analysis that is "technology- neutral," that is, without consideration of specific technologies, but using the fundamental physics characteristics of each part of the fuel cycle. The study focused on the fuel cycle performance benefits at the fuel cycle equilibrium state, with only limited consideration of transition and deployment impacts. Common characteristics of the four most promising fuel cycle options include continuous recycle of all U/Pu or U/TRU, the use of fast-spectrum reactors, and no use of uranium enrichment once fuel cycle equilibrium has been established. The high-level wastes are mainly from processing of irradiated fuel, and there would be no disposal of any spent fuel. Building on the findings of the E&S study, additional studies have been conducted in the last two years following the information exchange meeting, the 13th IEMPT, which was held in Seoul, the Republic of Korea in 2014. Insights are presented from the recent studies on the benefits and challenges of recycling minor actinides, and transition considerations to some of the most promising fuel cycle options.

Wigeland, Roald↗

Integrated Sustainable Product Design With Warranty and End-of-Use Considerations

The concept of integrated sustainable product design has recently emerged, aiming to incorporate downstream life cycle performance into the initial product design to enhance sustainability. Various sustainable product design tools based on life cycle assessment or quality function deployment have been established while the impact of reliability on circular practices has received limited attention. Recognizing the critical role of product reliability in post-design performance, this paper develops a product design optimization model that considers the warranty performance and the effect of end-of-use options. The model takes into account the effect of uncertain operating conditions on product reliability. Two optimization goals including the minimization of expected unit life cycle cost and environmental impact are achieved by the model. To demonstrate the benefits of the integrated approach, the model is applied to an electric motor design problem. The results highlight that integrating end-of-use options in the early design phase leads to adjustments in component selection and reliability design. Moreover, the circular utilization of used products enables cost savings throughout the product’s life cycle and contributes to environmental impact reduction. Finally, the study analyzes the effects of operating conditions, warranty policies, and take-back prices for used products on design decisions, providing valuable insights for product designers.

Integrated design↗

Combined Effects of Uniform Applied Pressure and Electrolyte Additives in Lithium-Metal Batteries

The development of lithium-metal batteries with good performance and long lifetimes requires fundamental insight into the mechanisms underlying performance improvements from individual design strategies and the interactions between multiple improvement approaches. Here, in this work, we investigated the individual and combined effects of applied pressure and a LiAsF 6 electrolyte additive on the performance of anode-free lithium-metal batteries; we employed various pressure application methods, which vary both in magnitude and uniformity. Both approaches individually improve cycling performance of anode-free lithium-metal batteries. Pressure increases the cycling efficiency at both the anode and cathode by promoting improved morphologies, while the LiAsF 6 additive additionally improves performance at the anode by enhancing the solid electrolyte interphase (SEI) properties. The combination of uniform applied pressure and a LiAsF 6 electrolyte additive produces lithium-metal batteries with cycling performance higher than can be achieved with either approach alone. This additional performance improvement is able to be realized due to the complementary rather than competitive nature of the mechanisms underlying applied pressure (lithium morphology) and electrolyte additives (SEI properties). Our results highlight the importance of moving beyond the investigation of isolated design strategies and demonstrate that superior cycling can be achieved by combining multiple approaches.

25 ENERGY STORAGE↗

A combined power and ejector refrigeration cycle for low temperature heat sources

A combined power and ejector refrigeration cycle for low temperature heat sources is under investigation in this paper. The proposed cycle combines the organic Rankine cycle and the ejector refrigeration cycle. The ejector is driven by the exhausts from the turbine to produce power and refrigeration simultaneously. A simulation was carried out to analyze the cycle performance using R245fa as the working fluid. A thermal efficiency of 34.1%, an effective efficiency of 18.7% and an exergy efficiency of 56.8% can be obtained at a generating temperature of 395 K, a condensing temperature of 298 K and an evaporating temperature of 280 K. Simulation results show that the proposed cycle has a big potential to produce refrigeration and most exergy losses take place in the ejector. (author)

42 ENGINEERING↗

{alpha}-Fe{sub 2}O{sub 3} as an anode material with capacity rise and high rate capability for lithium-ion batteries

Graphical abstract: Nanosized porous {alpha}-Fe{sub 2}O{sub 3} powder was successfully synthesized via the molten salt method. Electrochemical measurement results demonstrated that the electrode properties of the {alpha}-Fe{sub 2}O{sub 3} could offers excellent cycling performance and high rate capability. The capacity of the product shows two different trends during cycling which are rarely reported in the literature, a decrease in capacity in the first 100 cycles and an increase afterwards up to 600 cycles, with the lowest and highest capacity around 970 and 1972 mAh/g, respectively. Research highlights: {yields} Nanosized {alpha}-Fe{sub 2}O{sub 3} as an anode material for lithium-ion battery. {yields} The nanosized {alpha}-Fe{sub 2}O{sub 3} shows excellent electrochemical performance and exhibits the feature of capacity increase upon cycling. {yields} The porous rhombohedral structures of {alpha}-Fe{sub 2}O{sub 3} could provides the short Li{sup +} diffusion length, decreases the traverse time for electrons and Li{sup +} ions, and reduces the volume expansion to some extent. {yields} The cubic structure of {alpha}-Fe{sub 2}O{sub 3} has been modified to a needle-like structure after prolonged cycling. -- Abstract: We report a simple molten salt method to prepare nanosize {alpha}-Fe{sub 2}O{sub 3}, as well as its electrochemical performance as anode material for lithium ion batteries. The structure and morphology were confirmed by Raman spectroscopy, X-ray diffraction, and transmission electron microscopy. The as-prepared {alpha}-Fe{sub 2}O{sub 3} is a rhombohedral phase of hematite with crystal size in the range of 20-40 nm. The electrochemical measurements were performed using the as-prepared powders as the active material for a lithium-ion cell. The nanosized {alpha}-Fe{sub 2}O{sub 3} shows excellent cycling performance and rate capability. It also exhibits the feature of capacity increase upon cycling. The outstanding electrochemical performance of the {alpha}-Fe{sub 2}O{sub 3} can be related to several factors, namely, the short Li{sup +} diffusion length along the porous rhombohedral structures and the nanosized nature of the materials, which decreases the traverse time for electrons and Li{sup +} ions, and reduces the volume expansion to some extent during charge/discharge reactions.

36 MATERIALS SCIENCE↗

Unraveling electrochemo-mechanical aspects of core–shell composite cathode for sulfide based all-solid-state batteries

All-solid-state lithium batteries (ASSLBs) are emerging as promising next-generation batteries for electric vehicles owing to their high energy densities and safety features. However, challenges such as inadequate material percolation and low cathode utilization often hinder their potential. This paper presents a core–shell approach to optimize the cathode active material (CAM) utilization. The resultant CAM composite showed high ionic conductivity, a highly dense microstructure with <10% porosity, and minimal stack pressure changes during electrochemical cycling. The maximum CAM utilization was achieved while effectively mitigating electrochemo-mechanical side reactions by applying a uniformly coated Li 6 PS 5 Cl solid electrolyte layer (≈500 nm) and a LiNbO 3 buffer layer (≈10 nm) onto LiNi 0.8 Mn 0.1 Co 0.1 O 2 particles (LPSCl@LNO@NMC). The engineered LPSCl@LNO@NMC composites, which incorporated a 5 wt% LPSCl coating on LNO@NMC powders, exhibited a dense microstructure that enhanced the mechanical stability at the cathode. Sulfide-based solid electrolyte (SSE)/SSE contact provided better ionic pathways within the composite and increased CAM utilization. Thus, an enhanced reversible capacity (197 mA h g -1 ) and exceptional high-rate cycling performance (86.3% capacity retention after 1000 cycles at 2C) were observed. These findings pave the way for the advancement and commercialization of high-performance ASSLBs.

25 ENERGY STORAGE↗

Increasing Main Cooler Thermal Performance for sCO2 Power Cycles

Increasing sCO2 power cycle cooler performance will increase the efficiency and lower the cost of electricity for sCO2 power cycles. This work considered the heat transfer performance of two counter-flow, shell-and-tube heat exchangers using local measurements. The heat exchangers were constructed using commercial tubing. One heat exchanger was constructed with a conventional, smooth inner tube (7 mm nominal inner diameter). The other was constructed with an additively manufactured tube with a square cross section and angled rib turbulators. For the present study, the measured Nusselt number was 30% less than the Dittus-Boelter correlation. The decrease was attributed to heat transfer degradation. The cooler performance was also reported as heat exchanger effectiveness. A factor of two improvement in Nusselt number (94%) relative to smooth conventional tubes was observed, indicating that heat transfer enhancement features (such as the ribs) are a suitable technology to overcome heat transfer degradation in sCO2 coolers. Trends in heat exchanger effectiveness indicated that the ribs were most beneficial when the water flow rates were at the low end of the range considered: 0.016 – 0.126 kg/s. Using results from prior system modeling, it is anticipated that adding heat transfer enhancement features in a cycle cooler will increase the sCO2 cycle efficiency by 0.34 percentage points.

Searle, Matthew↗

Increasing Main Cooler Thermal Performance for sCO2 Power Cycles

Increasing sCO2 power cycle cooler performance will increase the efficiency and lower the cost of electricity for sCO2 power cycles. This work considered the heat transfer performance of two counter-flow, shell-and-tube heat exchangers using local measurements. The heat exchangers were constructed using commercial tubing. One heat exchanger was constructed with a conventional, smooth inner tube (7 mm nominal inner diameter). The other was constructed with an additively manufactured tube with a square cross section and angled rib turbulators. For mixed mean temperatures away from the pseudocritical temperature, the heat transfer coefficient matched the Dittus-Boelter correlation. As the mixed mean temperature approached the pseudocritical temperature, the heat transfer coefficient deviated from the Dittus-Boelter correlation due to transverse property variation and buoyancy. The local and average heat transfer coefficients for angled rib tubes were nominally 150% to 300% greater than the heat transfer coefficients for the smooth tube. Trends in heat exchanger effectiveness indicated that the ribs were most beneficial when the water flow rates were at the low end of the range considered: 0.016 – 0.126 kg/s. Using results from prior system modeling, it is anticipated that adding heat transfer enhancement features in a cycle cooler will increase the sCO2 cycle efficiency by 0.34 percentage points.

Searle, Matthew↗

Stabilized Electrode/Electrolyte Interphase by a Saturated Ionic Liquid Electrolyte for High-Voltage NMC532/Si-Graphite Cells

Nonaqueous electrolyte has become one of the technical barriers in enabling Li-ion battery comprising of a high voltage cathode and high capacity anode. Here, we demonstrate a saturated piperidinum bis(fluorosulfonyl)imide ionic liquid (IL) with a LiFSI salt not only supports the redox reaction on the cathode at high voltages, but also shows exceptional kinetic stability on the lithiated anode as evidenced by its improved cycling performance in a NMC532/Si-graphite full cells cycled between 4.6 and 3.0 V. On the basis of the spectroscopic/microscopic analysis and molecular dynamics (MD) simulations, the superior performance of the cells is attributed to the formation of solid-electrolyte-interphase on both electrode as well as unique solvation structure where a deadlocked coordination network is established at the saturated state, which prevents transition metal dissolution into the electrolyte via a solvation process.

25 ENERGY STORAGE↗

Tailoring the Pore Size of a Polypropylene Separator with a Polymer Having Intrinsic Nanoporosity for Suppressing the Polysulfide Shuttle in Lithium–Sulfur Batteries

Lithium–sulfur (Li–S) batteries are being considered as one of the most promising candidates for the development of next-generation energy storage technologies. Although much progress has been made over the past decade, the development of Li–S batteries is still held back by a crucial polysulfide-shuttle problem. To address this critical issue, an approach to reduce the pore size of the separator is presented here, to prevent the penetration of soluble polysulfide species. A polymer with intrinsic nanoporosity (PIN) is developed within the micrometer-scale pores of a polypropylene separator. The framework of polypropylene acts as a skeleton to sustain reliable mechanical properties with the thin membrane. Upon the formation of PIN in the pores, the polypropylene separator maintains its thickness. With the thin PIN–polypropylene membrane, the Li–S cells can be operated with a relatively high sulfur loading. The PIN allows the transport of Li + ions, but suppresses the penetration of the polysulfide species. The Li–S batteries with the PIN-modified polypropylene separator exhibit enhanced cycling performance.

25 ENERGY STORAGE↗

University of Missouri Research Reactor LEU Fuel Element Flow Test Conceptual Design—Hydraulic Reactor Design Parameters

The University of Missouri-Columbia Research Reactor (MURR®) is one of five U.S. high performance research reactors (USHPRR), plus one critical facility, that actively collaborates with the National Nuclear Security Administration (NNSA) Material Management and Minimization(M 3 ) Reactor Conversion Program to convert to the use of low-enriched uranium (LEU, < 20 wt.% U-235) fuel. A new type of LEU fuel with very high density, based on an alloy of uranium and 10 weight percent molybdenum (U-10Mo), is expected to allow the conversion to LEU of USHPRR that have been found unable to be converted with previously qualified uranium silicide-aluminum (U 3 Si 2 -Al) dispersion fuel. MURR has been working with the USHPRR Reactor Conversion (RC) Pillar at Argonne National Laboratory to perform fuel element design and fuel cycle performance analyses, steady-state thermal hydraulics safety analyses, and accident safety analyses in preparation for the conversion of MURR and to support a preliminary Safety Analysis Report (SAR) for conversion to LEU fuel. This work is performed in preparation for the flow test campaign that will be conducted by the USHPRR RC Pillar. The purpose of the hydraulic performance evaluation of the MURR LEU fuel element designed by the RC Pillar is to test a prototypic commercially fabricated LEU fuel element to determine whether any failure modes are observed or predicted in the fuel element, including significant deformations such as plate bending, twisting, or plate detachment from the side plate under selected safety-basis limits for reactor hydraulic conditions. To support the design of the flow test for MURR LEU fuel element hydraulic performance evaluation, design parameters for hydraulic testing of the LEU fuel element are laid out in this report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Massachusetts Institute of Technology Reactor LEU Fuel Element Flow Test Conceptual Design – Hydraulic Reactor Design Parameters

The Massachusetts Institute of Technology Reactor (MITR-II, also referred to as MITR) is one of six U.S. high performance research reactors (USHPRR), including one critical facility, that is actively collaborating with the U.S. National Nuclear Security Administration (NNSA) Material Management and Minimization (M 3 ) Reactor Conversion Program to convert to the use of low-enriched uranium (LEU, < 20 wt% 235 U) fuel. The MIT Nuclear Reactor Laboratory has been working with the USHPRR Reactor Conversion (RC) Pillar at Argonne National Laboratory to perform fuel element design and fuel cycle performance analyses, steady-state thermal hydraulics safety analyses, and accident safety analyses in preparation for the conversion of MITR and support a preliminary Safety Analysis Report (SAR) for conversion to LEU fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Integrated reactor architecture of conductive network and catalytic nodes to accelerate polysulfide conversion for durable and high-loading Li-S batteries

The development of carbon-based heterogeneous framework host with synergistic catalytic and conductive effects for sulfur cathode is a promising strategy to realize high performance lithium sulfur batteries (LSBs). Here, an integrated reactor architecture with defective carbon nodes (IRA-DC) is designed for serving as high-loading (92.4 wt%) sulfur host. The hierarchical porous IRA-DC consists of untangled conductive carbon nanotube network and Co/N co-doped catalytic nodes with high dispersity. Therein the optimization of electric field distribution and homogenization of adsorption-catalysis sites offer the multi-electron conversion reaction of polysulfides with excellent kinetics and stability. The resultant IRA-DC/S cathode enables a high areal capacity of 8.86 mAh cm -2 under ultra-high sulfur loading (13.1 mg cm -2 ) and lean electrolyte (8 μL mg sulfur -1 ). It also displays a long-term cycling performance (1200 cycles at 1 C) and ultrahigh rate performance up to 20 C (with a capacity of 473.6 mAh g -1 ). In conclusion, this work provides an electrode building strategy by optimizing the environments of heterogeneous electrocatalysis and micro electric field to activate the polysulfide conversion efficiency and utilization of high-loading sulfur in monolithic sulfur-carbon cathodes.

25 ENERGY STORAGE↗

University of Missouri Research Reactor (MURR) LEU Fuel Fluid-Structure Interaction Analysis

The University of Missouri Research Reactor (MURR ® ) is one of five U.S. high performance research reactors (USHPRR), plus one critical facility, that are actively collaborating with the National Nuclear Security Administration (NNSA) Material Management and Minimization (M 3 ) Reactor Conversion Program to convert from highly enriched uranium (HEU, ≥ 20 wt.% U-235) to low-enriched uranium (LEU, < 20 wt.% U-235) fuel. A new type of LEU fuel with very high density, based on an alloy of uranium and 10 weight percent molybdenum (U-10Mo), is expected to allow the conversion to LEU of USHPRR that have been found unable to be converted with previously qualified uranium silicide-aluminum (U 3 Si 2 -Al) dispersion fuel. MURR has been working with the USHPRR Reactor Conversion (RC) Pillar at Argonne National Laboratory to perform fuel element design and fuel cycle performance analyses, steady-state thermal hydraulics safety analyses, and accident safety analyses in preparation for the conversion of MURR and to support a preliminary Safety Analysis Report (SAR) for conversion to LEU fuel. In this work, Fluid-structure interaction (FSI) analysis at the fuel element level, as compared to the fuel plate level of the previous work. is performed which models all components of the MURR LEU fuel element, including fuel plates and the supporting structures e.g., side plates, end fittings, and combs. Therefore, the effect of supporting structures on the coolant flow distribution, the fuel plate deflection, and the resulting coolant channel gap reduction can be evaluated. In addition to the nominal element geometry and flow rate, the tolerances in the geometry dimensions of coolant channel and plate thickness, the effect of a comb on plate deflection, and the uncertainty of the flow rate per element are considered in this work. The effect of comb on plate displacement is quantified through two bounding cases: the case assuming a perfect bond between the comb and plates and the case neglecting the comb effect. Note that in this analysis, the FSI has been decoupled from the other structural effects caused by irradiation (e.g., swelling and irradiation creep). Assessment of combined effects is planned for a later stage of this project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-Rate, Durable Sodium-Ion Battery Cathode Enabled by Carbon-Coated Micro-Sized Na 3 V 2 (PO 4 ) 3 Particles with Interconnected Vertical Nanowalls

Na-ion batteries have been regarded as promising alternatives for Li-ion batteries due to the extensive sodium reserves in the world. Na3V2(PO4)3 has been proved to be a good candidate of the cathode materials in Na-ion batteries but the intrinsic low electrical conductivity and sluggish kinetics handicapped its application. Here, 3D hierarchical Na3V2(PO4)3 particles are synthesized by a facile hydrothermal method, constructed by carbon-coated 2D Na3V2(PO4)3 nanowalls. Superior cell performance of high rate capability and cycle stability are observed in the well-defined structure. As the cathode in Na-ion batteries, it delivers a high capacity almost reaching the theoretical one and exhibits high capacity retention. The enhanced rate capability and cycle performance can be attributed to the improved electrical conductivity from the interconnected carbon layer and the shortened ion diffusion length and high specific surface area from the nanowalls.

36 MATERIALS SCIENCE↗

Construction of Fluorine- and Piperazine-Engineered Covalent Triazine Frameworks Towards Enhanced Dual-Ion Positive Electrode Performance

Organic positive electrodes featuring lightweight, and tunable energy storage modes by molecular structure engineering have promising application prospects in dual-ion batteries. Herein, a series of highly porous covalent triazine frameworks (CTFs) were synthesized under ionothermal conditions using fluorinated aromatic nitrile monomers containing a piperazine ring. Fluorinated monomers can result in more defects in CTFs, leading to a higher surface area up to 2515 m 2 /g and a higher N content of 11.34 wt% compared to the products from the non-fluorinated monomer. The high surface area and abundant redox sites of these CTFs afforded high specific capacities (up to 279 mAh/g at 0.1 A/g), excellent rate performance (89 mAh/g at 5 A/g), and durable cycling performance (92.3% retention rate after 500 cycles at 2.0 A g -1 ) as dual-ion positive electrodes

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗