SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Stability under changes of temperature and current increased. External etalon aligned with laser diode provides optical feedback enhancing stability of operation in one or few of longitudinal laser modes. Provides amount of feedback varying periodically with wavelength. Also helps to increase stability by reducing sensitivity to minor feedback from external objects other than etalon.
Preliminary results pertaining to spectral reconstruction using Burst and Transient Source (BATSE) Large Area Detector measurements of solar flares are presented. The solar flare measurements are currently being used to fine tune the calibration of our data analysis software. The current status of the stability of spectral analysis, given the systematic errors present in burst location, are given. A brief description is given of enhancements to the input data for the atmospheric scattering algorithm that will be implemented in the data analysis software.
High T sub C superconducting thick film were prepared by a screen printing process. Y-based (YBa2Cu3O(7-x) superconducting thick film were printed on 211/Al2O3, SNT/Al2O3, and YSZ substrates. Because of poor adhesion of the superconductor thick films to 211/Al2O3 and SNT/Al2O3 substrates, relatively low T sub C and J sub C values were obtained from the films printed on these substrates. Critical temperatures (T sub C) of YBa2Cu3O(7-x) thick films deposited on 211/Al2O3 and SNT/Al2O3 substrates were about 80 K. The critical current densities (J sub C) of these films were less than 2 A/sq cm. Higher T sub C and J sub C YBa2Cu3O(7-x) thick films were printed on YSZ substrates. A YBa2Cu3O(7-x) thick film with T sub C=86.4 and J sub C= 50.4 A/sq cm was prepared by printing the film on YSZ substrate and firing at 990 C for 10 minutes. Multiple-lead samples were also prepared on the YSZ substrates. The multiple-lead samples showed lower T sub C and/or J sub C values than those of the plain samples. The electrical properties of YBa2Cu3O(7-x) thick films were determined by the microstructures of the films. The YBa2Cu3O(7-x) thick films printed on the YSZ substrates, which had the best properties among the films printed on the three different kinds of substrates, had the highest density and the best particle interconnection. The YBa2Cu3O(7-x) thick films with preferred orientation in (001) direction were obtained on the YSZ substrates. Cracks, which retard the properties of the films, were found from the films deposited on the YSZ substrates. Currently, a MSZ (Magnesium Stabilized Zirconia) substrate, which had higher thermal expansion coefficient than the YSZ substrate, is used as substrate for the YBa2Cu3O(7-x) thick film in order to eliminate the cracks on the film. Bi-based superconductor thick films were printed on polycrystalline MgO and YSZ substrates. Interactions between BSCCO thick films and the YSZ substrates were observed. Various buffer layer materials were applied onto the substrates in order to avoid the interactions between the BSCCO thick films and the ZrO2-based substrates. So far, a BSCCO printed on MgO substrate with T Sub C=89K was obtained. The J sub C of the film was lower than 0.1 A/sq cm by reason of poor interconnectivity of the BSCCO particles.
Lightweight, low-power circuit provides noncontact measurement of alternating or direct current of many ampheres in main conductor. Advantages of circuit over other nulling Hall-effect current-measuring circuits is stability and accuracy increased by putting both analog-to-digital and digital-to-analog converters in nulling feedback loop. Converters and rest of circuit designed for operation at sampling rate of 100 kHz, but rate changed to alter time or frequency response of circuit.
A proof-of-feasibility demonstration showed that high temperature superconductor (HTS) coils can be used in a high-load, active magnetic bearing in liquid nitrogen. A homopolar radial bearing with commercially wound HTS (Bi 2223) bias and control coils produced over 200 lb (890 N) radial load capacity (measured non-rotating) and supported a shaft to 14000 rpm. The goal was to show that HTS coils can operate stably with ferromagnetic cores in a feedback controlled system at a current density similar to that in Cu in liquid nitrogen. Design compromises permitted use of circular coils with rectangular cross section. Conductor improvements will eventually permit coil shape optimization, higher current density and higher bearing load capacity. The bias coil, wound with non-twisted, multifilament HTS conductor, required negligible power to carry its direct current. The control coils were wound with monofilament HTS sheathed in Ag. These dissipated negligible power for direct current (i.e. for steady radial load components). When an alternating current (AC) was added, the AC component dissipated power which increased rapidly with frequency and quadratically with AC amplitude. In fact at frequencies above about 2 hz, the effective resistance of the control coil conductor actually exceeds that of the silver which is in electrical parallel with the oxide superconductor. This is at least qualitatively understandable in the context of a Bean-type model of flux and current penetration into a Type II superconductor. Fortunately the dynamic currents required for bearing stability are of small amplitude. These results show that while twisted multifilament conductor is not needed for stable levitation, twisted multifilaments will be required to reduce control power for sizable dynamic loads, such as those due to unbalance.
Wind profile measurement and the simulation of aerodynamic loads on a launch vehicle play an important role in determining launch capability and post launch assessment of the vehicle's performance. To date, all United States range certified wind profile measurement systems have been based on balloon tracking. Since the 1960's, the standard used by the National Aeronautics and Space Administration and the Air Force at the Cape Canaveral Air Station (CCAS) for detailed wind profile measurements has been the radar tracked, aerodynamically stabilized Jimsphere balloon system. Currently, the Air Force is nearing certification and operational implementation of the Automated Meteorological Profiling System (AMPS) at CCAS and Vandenburg Air Force Base (VAFB). AMPS uses the Global Positioning System for tracking the Jimsphere balloon. It is anticipated that the AMPS/Jimsphere, named the High Resolution Flight Element (HRFE), will have equivalent, or better resolution than the radar tracked Jimsphere, especially when the balloon is far downrange, at a low elevation angle. By the 1980's, the development of Doppler Wind Profilers (DWP) had become sufficiently advanced to justify an experimental measurement program at Kennedy Space Center (KSC). In 1989 a 50 MHz DWP was installed at KSC. In principal, the 50 MHz DWP has the capability to track the evolution of wind profile dynamics within 5 minutes of a launch. Because of fundamental differences in the measurement technique, there is a significant time and space differential between 50 MHz DWP and HRFE wind profiles. This paper describes a study to quantify these differences from a sample of 50 MHz DWP/HRFE pairs obtained during the AMPS certification test program.
A new, fourth generation, single crystal superalloy has been jointly developed by GE Aircraft Engines, Pratt & Whitney, and NASA. The focus of the effort was to develop a turbine airfoil alloy with long-term durability for use in the High Speed Civil Transport. In order to achieve adequate long-time strength improvements at moderate temperatures and retain good microstructural stability, it was necessary to make significant composition changes from 2nd and 3rd generation single crystal superalloys. These included lower chromium levels, higher cobalt and rhenium levels and the inclusion of a new alloying element, ruthenium. It was found that higher Co levels were beneficial to reducing both TCP precipitation and SRZ formation. Ruthenium caused the refractory elements to partition more strongly to the ' phase, which resulted in better overall alloy stability. The final alloy, EPM 102, had significant creep rupture and fatigue improvements over the baseline production alloys and had acceptable microstructural stability. The alloy is currently being engine tested and evaluated for advanced engine applications.
One key factor that limits the performance of current gas turbine engines is the temperature capability of hot section structural components. Silicon-based ceramics, such as SiC/SiC composites and monolithic Si3N4, are leading candidates to replace superalloy hot section components in the next generation gas turbine engines due to their excellent high temperature properties. A major stumbling block to realizing Si-based ceramic hot section components is the recession of Si-based ceramics in combustion environments due to the volatilization of silica scale by water vapor. An external environmental barrier coating (EBC) is the most promising approach to preventing the recession. Current EBCs are based on silicon, mullite (3A12O3-2SiO2) and BSAS (barium strontium aluminum silicate with celsian structure). Volatility of BSAS, BSAS-silica chemical reaction, and low melting point of silicon limit the durability and temperature capability of current EBCs. Research is underway to develop EBCs with longer life and enhanced temperature capability. Understanding key issues affecting the performance of current EBCs is necessary for successful development of advanced EBCs. These issues include stress, chemical compatibility, adherence, and water vapor stability. Factors that affect stress are thermal expansion mismatch, phase stability, chemical stability, elastic modulus, etc. The current understanding on these issues will be discussed.
Stellar Imager (SI) will be a Space-Based telescope consisting of 20 to 30 separated apertures. It is designed for UV/Optical imaging of stellar surfaces and asteroseismology. This report describes details of an alternative optical design for the beam combiner, dubbed the Spatial Frequency Remapper (SFR). It sacrifices the large field of view of the Fizeau combiner. In return, spectral resolution is obtained with a diffraction grating rather than an array of energy-resolving detectors. The SFR design works in principle and has been implemented with MIRC at CHARA for a small number of apertures. Here, we show the number of optical surfaces can be reduced and the concept scales gracefully to the large number of apertures needed for Stellar Imager. We also describe a potential application of this spatial frequency remapping to improved imaging with filled aperture systems. For filled-aperture imaging, the SFR becomes the core of an improved aperture masking system. To date, aperture-masking has produced the best images with ground-based telescopes but at the expense of low sensitivity due to short exposures and discarding most of the light collected by the telescope. This design eliminates the light-loss problem previously claimed to be inherent in all aperture-masking designs. We also argue that at least in principle, the short-integration time limit can also be overcome. With these improvements, it becomes an ideal camera for TPF-C; since it can form speckle-free images in the presence of wavefront errors, it should significantly relax the stability requirements of the current designs.
High- and low-resolution sea surface temperature (SST) analysis products are used to initialize the Weather Research and Forecasting (WRF) Model for May 2004 for short-term forecasts over Florida and surrounding waters. Initial and boundary conditions for the simulations were provided by a combination of observations, large-scale model output, and analysis products. The impact of using a 1-km Moderate Resolution Imaging Spectroradiometer (MODIS) SST composite on subsequent evolution of the marine atmospheric boundary layer (MABL) is assessed through simulation comparisons and limited validation. Model results are presented for individual simulations, as well as for aggregates of easterly- and westerly-dominated low-level flows. The simulation comparisons show that the use of MODIS SST composites results in enhanced convergence zones. earlier and more intense horizontal convective rolls. and an increase in precipitation as well as a change in precipitation location. Validation of 10-m winds with buoys shows a slight improvement in wind speed. The most significant results of this study are that 1) vertical wind stress divergence and pressure gradient accelerations across the Florida Current region vary in importance as a function of flow direction and stability and 2) the warmer Florida Current in the MODIS product transports heat vertically and downwind of this heat source, modifying the thermal structure and the MABL wind field primarily through pressure gradient adjustments.
Icing alters the shape and surface characteristics of aircraft components, which results in altered aerodynamic forces and moments caused by air flow over those iced components. The typical effects of icing are increased drag, reduced stall angle of attack, and reduced maximum lift. In addition to the performance changes, icing can also affect control surface effectiveness, hinge moments, and damping. These effects result in altered aircraft stability and control and flying qualities. Over the past 80 years, methods have been developed to understand how icing affects performance, stability, and control. Emphasis has been on wind-tunnel testing of two-dimensional subscale airfoils with various ice shapes to understand their effect on the flowfield and ultimately the aerodynamics. This research has led to wind-tunnel testing of subscale complete aircraft models to identify the integrated effects of icing on the aircraft system in terms of performance, stability, and control. Data sets of this nature enable pilot-in-the-loop simulations to be performed for pilot training or engineering evaluation of system failure impacts or control system design.
As long-term spaceflight missions become ever more imminent, astronaut nutrition and diet require further investigation and development. Dehydrated or stabilized food sources are currently used for spaceflight, but growing fresh produce aboard spacecraft can potentially supplement the astronauts’ diets. Further, having astronauts work with plants while in space can provide psychological benefits by serving as a tangible passage of time and representing a living component aboard an otherwise mechanical environment. As spaceflight duration will lengthen as missions head back to the Moon and to Mars, having the ability and knowledge to grow fresh produce will become even more vital. The following experiments were conducted in the late summer and fall of 2018. The purpose of these studies were to examine potential off-gas from a system component that could potentially inhibit plant germination, optimizing lighting methods and protocol for mizuna production, determining a fertilizer method that best promotes healthy mizuna yields, and troubleshooting tomato production for the next generation of the Vegetable Production System.
Magnetic reconnection is a fundamental process operating in laboratory, space, and astrophysical plasmas. We understand today that it is the mechanism behind the often explosive release of the stored magnetic energy, and that it directly or indirectly powers as diverse a set of phenomena as solar eruptions, stellar flares, geomagnetic storms, the aurora, and even disruption events in fusion machines. It is also the mechanism powering the majority of the deleterious space effects collectively referred to as “space weather.” Owing to its importance, reconnection has been a research focus for many years, culminating in the research based on NASA’s Magnetospheric Multiscale mission. A major component of foundational research involved studies of the stability and disruption of current sheets by collisionless tearing, which still plays a major role in the dynamical evolution of the interfaces between magnetic fields of different directions. This presentation will illuminate these beginnings, with special focus on the seminal work of Academician A. A. Galeev, and also provide a summary of the present state of knowledge. It will conclude with an outlook toward future reconnection research targets.
Aerogels can be used in spaceflight applications as thermal insulators due to their low density, low thermal conductivity, and tortuous path for solid conduction. However, the aerogel formulation must be optimized to increase the thermal stability of the aerogels as drastic densification and decrease in surface area is often exhibited after high-temperature exposure. Current research investigates yttria-stabilized zirconia (YSZ) aerogels, which have low thermal conductivity and are expected to be used between 600°C and 1000°C. We anticipate that new sol-gel chemistries and processing will yield YSZ aerogels that display retained mesoporous structure, increased surface area, and minimized shrinkage upon exposure to higher temperatures in the projected use range. This work investigates the cationic surfactant, cetrimonium bromide (CTAB), as a templating agent to prevent the collapse of the aerogel pore structure upon gelation and drying. It was determined that adding one-half times the critical micelle concentration (CMC) of CTAB increased the surface area and pore volume of the aerogels, as compared to aerogels without CTAB or with twice the CMC of CTAB, following high-temperature exposure. By optimizing CTAB, the thermal stability of YSZ aerogels can be enhanced to make these materials more efficient when used as thermal management systems.
The topic of this presentation is a multi-center effort to improve the undersanding and characterization of dynamic stability. An assessment of existing experimental and computational tools for characterizing dynamic stability will be discussed. Current state-of-the-art experimental techniques, and known gaps/overlaps between facilities is presented. Finally, advancements in computational capabilities under the direction of ESM is presenting using the Free-Flight CFD solver within US3D.
Venus currently has a hostile surface environment with temperatures of ~460 ºC, pres-sures near 92 bars, and an atmosphere composed of super critical CO2 hosting a myriad of other potentially reactive gases (e.g., SO2, HCl, HF). However, it has been proposed that its surface may not have always been so harsh. Models suggest there may have been billions of years of clement conditions allowing an Earth-like environment with liquid water oceans. If such conditions existed, it is possible Venus formed a similar array of hydrous or aqueous minerals as seen on other planets with liquid surface water (e.g., Mars, Earth). Based on thermodynamic modeling, many of these phases would not be stable under the current atmospheric conditions on Venus, dehydrating due to the high temperatures and low concentration of H2O in the atmosphere. However, the rate of decomposition of these phases may allow them to remain present on the surface over geologic time. For example, experiments on the reaction rate of tremolite (Ca2Mg5Si8O22(OH)2) show a 50% decomposition time of 2.7 Gyr for micrometer sized grains in unreactive atmospheres (i.e., without SO2) at 740 K, and a 50% decomposition time of 70 Gyr for crystals several millimeters to centimeters in size. If hydrous minerals can remain on the surface of Venus over geologic time, it has implications for our detection of evidence of these past environments, and also for the overall water budget of the planet. If after surficial dehydration the planet was able to still store water in its crust, possible processes such as subduction or metamorphism could still have operated using stored water long after liquid surface water evaporated. Several previous studies have focused on experimental investigations of mineral stability on Venus. In particular, the works of studied the decomposition rate of tremolite under conditions relevant to Venus. As their focus was on decomposition of the mineral due to lack of water in the atmosphere, their experiments were undertaken using only CO2 or N2 gas at atmospheric pressure. Re-cent experiments have examined reactivity of other minerals with the Venusian atmosphere using more complex gas compositions at similar pressures to those seen on Venus. These studies show reaction of silicate minerals with atmospheric components on relatively short timescales (i.e., on the order of days). The reported reactions of silicate materials in both studies produced iron oxides, Ca sulfates, and Na sulfates. These ions are present in many amphiboles, and Ca was proposed by Johnson and Fegley to potentially have an important role in the decomposition mechanism for tremolite, with the Ca-O bond being the first to break during decomposition. The potential involvement of Ca in both processes raises the question of whether or not the reaction to form a secondary mineral phase will influence the rate of amphibole break-down (e.g., discussion in for tremolite). Additionally, reaction of Ca with atmospheric gases may result in a different secondary mineral assemblage than simple amphibole decomposition, which will need to be recognized when searching for evidence of past hydrated minerals on the Venusian surface. In order to understand the effect of this reaction on the overall preservation potential of amphibole on the surface of Venus, we are conducting experiments in both reactive and nonreactive atmospheres using the mineral actinolite (Ca2(Mg,Fe)5Si8O22(OH)2), an amphibole with similar crystal structure to tremolite that contains both Ca and Fe.
An understanding of the composition, structure, transport and photochemical processes of the present atmosphere of Mars is essential for addressing such fundamental questions as the stability, evolution and the origin of the Martian atmosphere. This paper discusses our current knowledge of the photochemistry and stability of the Martian atmosphere, with special emphasis on new models and work in progress.
The food systems slated for future NASA missions must meet crew nutritional needs, be acceptable for consumption, and use resources efficiently. Although the current food system of prepackaged, moderately stabilized food items works well for International Space Station (ISS) missions, many of the current space menu items do not maintain acceptability and/or nutritive value beyond 2 years. Longer space missions require that the food system can sustain the crew for 3 to 5 years without replenishment. The task "Integration of Product, Package, Process, and Environment: A Food System Optimization" has the objective of optimizing food-product shelf life for the space-food system through product recipe adjustments, new packaging and processing technologies, and modified storage conditions. Two emergent food processing technologies were examined to identify a pathway to stable, wet-pack foods without the detrimental color and texture effects. Both microwave-assisted thermal sterilization (MATS) and pressure-assisted thermal stabilization (PATS) were evaluated against traditional retort processing to determine if lower heat inputs during processing would produce a product with higher micronutrient quality and longer shelf life. While MATS products did have brighter color and better texture initially, the advantages were not sustained. The non-metallized packaging film used in the process likely provided inadequate oxygen barrier. No difference in vitamin stability was evident between MATS and retort processed foods. Similarly, fruit products produced using PATS showed improved color and texture through 3 years of storage compared to retort fruit, but the vitamin stability was not improved. The final processing study involved freeze drying. Five processing factors were tested in factorial design to assess potential impact of each to the quality of freeze-dried food, including the integrity of the microstructure. The initial freezing rate and primary freeze drying temperature and pressure were linked to final product quality in freeze-dried corn, indicating processing modifications that could lead to improved product shelf life. Storage temperatures and packaging systems were also assessed for the impact to food quality. Reduced temperature storage had inconclusive impact to the progression of rancidity in butter cookies. Frozen storage was detrimental to fruit and vegetable textural attributes but refrigerated storage helped to sustain color and organoleptic ratings for plant-based foods. With regard to packaging systems, the metallized film overwrap significantly decreased the progression of the rancidity of butter cookies as compared to the highest barrier non-metallized film. The inclusion of oxygen scavengers resulted in noticeable moisture gains in butter cookies over time, independent of packaging film systems. Neither emergent processing technology nor the freeze dry optimization resulted in compelling quality differences from current space food provisions such that a five-year shelf life is likely with these processing changes alone. Using a combination of refrigeration and PATS processing is expected to result in organoleptically-acceptable fruit quality for most fruits through five years. The vitamin degradation will be aided somewhat by the cold temperatures but, given the labile nature of vitamin C, a more stable fortification method, such as encapsulation, should also be investigated to ensure vitamin delivery throughout the product life. Similarly, significant improvement to the packaging film used in the MATS processing, optimization of formulation for dielectric properties, vitamin fortification, and reduced temperature storage should be investigated as a hurdle approach to reach a five year shelf life in wet-pack entrees and soups. Baked goods and other environmentally-sensitive spaceflight foods will require an almost impenetrable barrier to protect the foods from oxygen and moisture ingress but scavengers and reduced storage temperature did not improve baked good shelf life and are not recommended at this time for these foods.