Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Current drive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Concept Design of a 1.4 MW Drive for Rotor Loss Minimization in a Partially Superconducting Motor

Partially superconducting machines with cryocooler-cooled rotors are a potential near-term technology that can achieve the motor performance needed by future fixed wing electric aircraft. For this type of machine, minimizing cryogenic heat load is one of the keys for enabling high machine performance. Rotor eddy current loss is often the most difficult cryogenic heat load to mitigate due to current ripple from the motor drive. This paper presents the concept design for a 20 kW/kg, 99.5% efficient motor drive that has sufficiently low current ripple to enable high performance partially superconducting machines by minimizing eddy current loss in the rotor. The motor drive concept design uses a resonant, interleaved, and multilevel topology to achieve these high-performance metrics with little current ripple. Rotor magnetic loss analysis using NASA’s 1.4 MW High Efficiency Megawatt Motor (HEMM) is used in the design process to down select the motor drive topology and show that the final design generates less than 5 W of magnetic loss in the rotor.

Cryogenic↗
NASA NTRS2018

Results of NASA Technical Challenge to Demonstrate Two-Speed Drive for Vertical Lift Vehicle

Currently, manned vertical lift vehicles are flown in a manner such that the rotors operate over a narrow range of rotating speed regardless if the vehicle's flight condition is one of vertical takeoff and landing, hover, or forward cruise. The propulsion systems are optimized for operation at the same, corresponding narrow range of rotor speed. However, certain missions and markets benefit greatly if the rotor speed can be adjusted over a wide range of speed to match demands of different missions and flight regimes. A vehicle that can operate with a wide range of rotor speeds would address key barriers to enable new markets and missions for vertical lift vehicles. Key barriers addressed by the wide-range of rotor speed include noise reduced via lower rpm rotor, increase of maximum forward flight speed, increased payload and range, reduced fuel burn, and lower operating costs. A new paradigm for the propulsion system is needed to enable these key benefits. One viable approach is to make use of a two-speed ratio drive system such that the engine can continue to operate over a narrow speed range, whereby engine performance is optimal, while adjusting the rotor speed as needed using the two-speed drive system. Motivated by such needs and by results of several system studies, a NASA Revolutionary Vertical Lift Technology Challenge was established to develop and demonstrate required technologies and designs for achieving a 50% reduction in rotor rpm via a two-speed drive system that incurs less than 2% power loss and maintains current power-to-weight ratios. The technical challenge work was completed and the technical objectives were achieved. This report describes the motivations, the research approach and the significant outcomes.

Transmissions↗
NASA NTRS2015

Two-dimensional Inductive Position Sensing System

A two-dimensional inductive position sensing system uses four drive inductors arranged at the vertices of a parallelogram and a sensing inductor positioned within the parallelogram. The sensing inductor is movable within the parallelogram and relative to the drive inductors. A first oscillating current at a first frequency is supplied to a first pair of the drive inductors located at ends of a first diagonal of the parallelogram. A second oscillating current at a second frequency is supplied to a second pair of the drive inductors located at ends of a second diagonal of the parallelogram. As a result, the sensing inductor generates a first output voltage at the first frequency and a second output voltage at the second frequency. A processor determines a position of the sensing inductor relative to the drive inductors using the first output voltage and the second output voltage.

Youngquist, Robert C.↗
NASA NTRS1996

Digital optical tape: Technology and standardization issues

During the coming years, digital data storage technologies will continue an aggressive growth to satisfy the user's need for higher storage capacities, higher data transfer rates and long-term archival media properties. Digital optical tape is a promising technology to satisfy these user's needs. As any emerging data storage technology, the industry faces many technological and standardization challenges. The technological challenges are great, but feasible to overcome. Although it is too early to consider formal industry standards, the optical tape industry has decided to work together by initiating prestandardization efforts that may lead in the future to formal voluntary industry standards. This paper will discuss current industry optical tape drive developments and the types of standards that will be required for the technology. The status of current industry prestandardization efforts will also be discussed.

Podio, Fernando L.↗
NASA NTRS1990

Agreements between ground-based and satellite-based observations

The polar ionospheric parameters obtained by the meridian chain of magnetometers are compared with those obtained by satellites, and a number of ionospheric quantities including the distribution of the electric potential, field-aligned currents, ionospheric currents and their equatorial counterparts, and the relationship between the AE index and the cross-polar cap potential is determined. It is noted that the agreement observed between the ground-based and satellite-based results allows to reduce the search for the driving mechanism of the ionospheric Pedersen current to identifying the driving mechanism of the Pedersen counterpart current in the equatorial plane.

Akasofu, S.-I.↗
NASA NTRS1995

MSATT: Mars Surface and Atmosphere Through Time

The papers published here are based on a workshop entitled "Mars: Past, Present, and Future: Results from the MSATT Program." MSATT (Mars Surface and Atmosphere Through Time) was the last of the Mars data analysis programs and functioned mainly through a series of focused workshops, the final one being held at the Lunar and Planetary Institute in Houston, Texas on November 15-17, 1993. The program began and ended with workshops that brought the entire MSATT community together. Here you will find papers that address the geology, mineralogy, and meteorology of Mars in an effort to assess how the surface and atmosphere of this fascinating planet have evolved over time. Could early Mars have been warmed by a brighter young sun instead of a massive greenhouse effect? Were glaciers and hydrological cycles part of Mars' relatively recent past, or was aeolian activity responsible for the putative glacial features? Do the SNCs come from a single source region, or is more than one site involved? And what really are the properties of Martian soils and what do they tell us about the weathering environment? Clearly, these are difficult questions, but progress toward answers can be found in this issue. Also contained in this issue are a mix of theoretical and observational papers that deal with the general circulation of the current atmosphere, the factors that drive it (dust properties), and the role it plays in controlling the current climate system.

Source record↗
NASA NTRS1983

The origins of Birkeland currents

Fundamental observations and zero-order theories for Birkeland currents are employed, together with recent observational data, to formulate a first-order model for the currents. Five categories of Birkeland currents are detailed, including region 1 current sheets which follow the auroral oval, region 2 currents with opposite polarity forming on the equatorward side, cusp currents poleward of region 1, currents appearing after extended periods of the interplanetary magnetic field, and a three-layer overlap of current sheets in the Harang discontinuity. The region 1 currents near noon are found to be driven by the interplanetary electric field on open field lines, while away from noon the inner edge of the plasma sheet is the source. Charge separation drives the region 2 currents, and neutralization is effected in the ionosphere. The magnetopause is concluded to be an insignificant factor for the Birkeland currents. Convection reversal is predicted to occur in the region 1 interior. Finally, four lobed polar electric fields are considered to be generated by the boundary layer dynamo, and indicate a closed magnetospheric configuration.

Stern, D. P.↗
NASA NTRS1966

Electropneumatic transducer automatically limits motor current

Pneumatic controller regulates the load on a centrifugal freon compressor in a water cooling system, thus limiting the current input to an electric motor driving it. An electromechanical transducer monitoring the motor input current sends out air signals which indicate changes in the current to the pneumatic controller.

Lovitt, T. F.↗
NASA NTRSDate not supplied

Current Status and Future Plans for Electric Motors and Drives at NASA

Our work advances propulsion for aircraft while reducing energy consumption, noise, emissions and the cost of air travel. We are committed to investigating the use of alternative energy sources and improving the safety and expediency of flight. Electrified Aircraft Propulsion (EAP) is the use of propulsors (propellers or fans) driven by electric motors to propel aircraft ranging from air taxis to subsonic transports. NASA is developing technology, aircraft concepts, test aircraft, and ground test facilities to turn this idea from science fiction to- reality. Specifically, motors and/or generators (Electric machines) are needed on all electrified aircraft. And NASA is sponsoring or performing work to achieve power densities 2-3 times the state of the art for machines in the MW or larger class. Three major machine types are being developed: permanent magnet, induction, and wound field. Power converters are also an essential component in most EAP aircraft concepts, as they are used to convert from ac to dc power, or vice versa. Silicon carbide and gallium nitride convertors are being developed with conventional cooling as well as a cryogenically cooled converter. Future plans include demonstrating integrated flight-ready systems in both ground and flight tests; collaborating with and leveraging ARPA-E EAP programs; and supporting FAA standards development for market acceptance and safety.

Aircraft↗
NASA NTRS1984

The interplanetary electric field, cleft currents and plasma convection in the polar caps

The relationship between the pattern of plasma convection in the polar cleft and the dynamics of the interplanetary electric field (IEF) is examined theoretically. It is shown that owing to the geometrical properties of the magnetosphere, the East-West component of the IEF will drive field-aligned currents which connect to the ionosphere at points lying on either side of noon, while currents associated with the North-South component of the IEF will connect the two polar caps as sheet currents, also centered at 12 MLT. In order to describe the consequences of the Interplanetary Magnetic Field (IMF) effects upon high-latitude electric fields and convection patterns, a series of numerical simulations was carried out. The simulations were based on a solution to the steady-state equation of current continuity in a height-integrated ionospheric current. The simulations demonstrate that a simple hydrodynamical model can account for the narrow 'throats' of strong dayside antisunward convection observed during periods of southward interplanetary IMF drift, as well as the sunward convection observed during periods of strongly northward IMF drift.

Banks, P. M.↗
NASA NTRS2004

LISA Thermal Design

The Laser Interferometer Space Antenna (LISA) mission, a space based gravitational wave detector, uses laser metrology to measure distance fluctuations between proof masses aboard three spacecraft. The total acceleration disturbance to each proof mass is required to be below 3 x 10(exp -15) meters per second squared per the square root of Hertz. Optical path length variations on each optical bench must be kept below about 3 pm per the square root of Hertz. Noise due to spacecraft thermal distortions, temperature difference variations across proof mass housing, and other thermal effects are expected to be a significant contributors to these noise budgets. The LISA Integrated Modeling team developed a detailed thermal model that is currently being used to drive the design of LISA. Several new thermal analysis techniques are also being developed in order to achieve model accuracies to LISA levels. We present here an overview of the LISA thermal design and modeling efforts. The latest thermal results calculated using the current baseline design of LISA are also discussed.

Merkowitz, Stephen↗
NASA NTRS2011

Two-Dimensional Analysis of Conical Pulsed Inductive Plasma Thruster Performance

A model of the maximum achievable exhaust velocity of a conical theta pinch pulsed inductive thruster is presented. A semi-empirical formula relating coil inductance to both axial and radial current sheet location is developed and incorporated into a circuit model coupled to a momentum equation to evaluate the effect of coil geometry on the axial directed kinetic energy of the exhaust. Inductance measurements as a function of the axial and radial displacement of simulated current sheets from four coils of different geometries are t to a two-dimensional expression to allow the calculation of the Lorentz force at any relevant averaged current sheet location. This relation for two-dimensional inductance, along with an estimate of the maximum possible change in gas-dynamic pressure as the current sheet accelerates into downstream propellant, enables the expansion of a one-dimensional circuit model to two dimensions. The results of this two-dimensional model indicate that radial current sheet motion acts to rapidly decouple the current sheet from the driving coil, leading to losses in axial kinetic energy 10-50 times larger than estimations of the maximum available energy in the compressed propellant. The decreased available energy in the compressed propellant as compared to that of other inductive plasma propulsion concepts suggests that a recovery in the directed axial kinetic energy of the exhaust is unlikely, and that radial compression of the current sheet leads to a loss in exhaust velocity for the operating conditions considered here.

Hallock, A. K.↗
NASA NTRS2011

Overview of ERA Ultra High Bypass Propulsor Technology Development

A review of the current research being conducted under the Environmentally Responsible Aviation (ERA) Ultra High Bypass (UHB) Testing subelement is presented. The four exiting tasks under the subelement, a description of each task, and the current status of each are given. The four tasks are: 1. Collaborate with P&W to design, fabricate and test a second generation of Geared Turbofan 2. Design, fabricate and test advanced Over the Rotor acoustic treatment and acoustically treated Soft Vanes 3. Develop a Shape Memory Alloy Variable Area Nozzle concept and demonstrate prototype 4. Refurbish and update the GRC Ultra High Bypass Drive Rig Following the current task updates, an overview of three proposed additional tasks to support the existing tasks is presented. The additional tasks would allow noise reduction and noise diagnostic testing technologies to be demonstrated at TRL 4 as part of existing planned fan model testing in the NASA Glenn 9 x15 Low Speed Wind Tunnel under the ERA UHB Testing subelement.

Hughes, Christopher↗
NASA NTRS2007

High-Voltage Power Supply With Fast Rise and Fall Times

A special-purpose high-voltage power supply can be electronically switched on and off with fast rise and fall times, respectively. The output potential is programmable from 20 to 1,250 V. An output current of 50 A can be sustained at 1,250 V. The power supply was designed specifically for electronically shuttering a microchannel plate in an x-ray detector that must operate with exposure times as short as 1 ms. The basic design of the power supply is also adaptable to other applications in which there are requirements for rapid slewing of high voltages. The power-supply circuitry (see figure) includes a preregulator, which is used to program the output at 1/30 of the desired output potential. After the desired voltage has been set, the outputs of a pulse width modulator (PWM) are enabled and used to amplify the preregulator output potential by 30. The amplification is achieved by use of two voltage doublers with a transformer that has two primary and two secondary windings. A resistor is used to limit the current by controlling the drive voltage of two field-effect transistors (FETs) during turn-on of the PWM. A pulse transformer is used to turn on four FETs to short-circuit four output capacitors when the outputs of the PWM have been disabled. The most notable aspects of the performance of the power supply are a rise time of only 80 s and a fall time of only 60 s at a load current of 50 A or less. Another notable aspect is that the application of a 0-to-5-V square wave to a shutdown pin of the PWM causes the production of a 0-to-1,250-V square wave at the output terminals.

Bearden, Douglas B.↗
NASA NTRS1978

Electromechanical flight control actuator, volume 2

Schematic diagrams are given for both the four-channel electromechanical actuator and the single-channel power electronics breadboard. Detailed design data is also given on the gears used in the differential gearbox and a copy of the operations manual for the system is included. Performance test results are given for the EMA motor and its current source indicator, the drive control electronics, and the overall system. The power converter waveform test results are also summarized.

Source record↗
NASA NTRS1983

Nonstationary coupling between the magnetosphere and ionosphere

Resonant coupling of large scale MHD waves to small scale kinetic Alfven waves is described. The small-scale waves drive field-aligned currents tens of micro A/sqm into the ionosphere with accelerated electrons of energies a few keV. Bounce resonant interaction with standing kinetic Alfven waves may precipitate higher energy electrons. East-west aligned arcs should be thinnest and move polewards relative to the plasma at the poleward edge. Downward travelling wave packets trap electrons between the wave front and the ionosphere whose energy is below the peak energy and whose phase-space density should be independent of the peak energy.

Goertz, C. K.↗
NASA NTRS1985

Mathematical physics approaches to lightning discharge problems

Mathematical physics arguments useful for lightning discharge and generation problems are pursued. A soliton Ansatz for the lightning stroke is treated including a charge generation term which is the ultimate source for the phenomena. Equations are established for a partially ionized plasma inding the effects of pressure, magnetic field, electric field, gravitation, viscosity, and temperature. From these equations is then derived the non-stationary generalized Ohm's Law essential for describing field/current density relationships in the horizon channel of the lightning stroke. The discharge initiation problem is discussed. It is argued that the ionization rate drives both the convective current and electric displacement current to increase exponentially. The statistical distributions of charge in the thundercloud preceding a lightning dischage are considered. The stability of the pre-lightning charge distributions and the use of Boltzmann relaxational equations to determine them are discussed along with a covered impedance path provided by the aircraft.

Kyrala, A.↗
NASA NTRS1992

Wavelength tunable liquid crystal imaging filters for remote sensing from geosynchronous platforms

Recent advances in liquid crystal technology have enabled us to construct tunable birefringent filters with bandwidths between approximately 0.1 nm and 50 nm. The center wavelength of these filters can be selected electronically, in a few tens of milliseconds, with no moving parts. These liquid crystal tunable filters (LCTF's), together with existing CCD detectors, make possible a new generation of lightweight, rugged, high-resolution imaging spectrophotometers. Such instruments would be particularly interesting for remote sensing applications from geosynchronous platforms. Important advantages exist in the aperture, absence of image shift, power consumption, size, weight, and absence of high drive frequencies, compared to current instruments used or considered for multispectral scene analysis. In the present work, we have reviewed spectral requirements of planned NASA geosynchronous remote sensing missions and identified several applications of the liquid crystal tunable filter technology. We have modeled the LCTF performance in the visible and near-infrared, and carried out a literature study on space-hardening of the filter components, to evaluate the suitability of LCTF's for geosynchronous missions. We have also compared the power consumption, weight, size, reliability, and optical performance of an imaging spectrophotometer using a LCTF monochromator, to other instruments that have been put forward for remote sensing from geosynchronous platforms. We put forward some conceptual designs for LCTF's that seem to offer important reliability, over the mechanical filter wheels presently baselined for the HEPI and ALM experiments. The extremely wide acceptance angle achievable with LCTF's could also avoid the present need for large-aperture interference filters in the ALM (and LIS) experiments. Thermal vacuum testing and radiation damage analysis is required to investigate the space hardening of these new filters for geosynchronous flight.

Foukal, Peter↗