Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cu”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

The series Bi2Sr2Ca(n-1) Cu(n)O(2n+4) (1 less than or equal to n less than or equal to 5): Phase stability and superconducting properties

Phase relations at 850 and 870 C, melting transitions in air, oxygen, and helium were studied for Bi(2.1)Sr(1.9) CuO6 and for the Bi2Sr2Ca(n-1) Cu(n)O(2n+4) for n = 1, 2, 3, 4, 5, and infinity (CaCuO2). Up to 870 C, the n = 2 composition resides in the compatibility tetrahedron bounded by Bi(2+x)(Sr,Ca)(3-y) Cu2O8, (Sr,Ca)14 Cu24O41, Ca2CuO3, and a Bi-Sr-Ca-O phase. The n is greater than or equal to 3 compositions reside in the compatibility tetrahedron Bi(2+x)(Sr,Ca)(3-y) Cu2O8 - (Sr,Ca)14 Cu24O41 - Ca2CuO3 - CuO up to 850 C. However, Bi(2+x)Sr(4-y) Cu3O10 forms for n is greater than or equal to 3 after extended heating at 870 C. Bi(2+x)Sr(2-y) CuO6 and Bi(2+x)(Sr,Ca)(3-y) Cu2O8 melt in air at 914 C and 895 C respectively. During melting, all of the compositions studied lose 1 to 2 percent by weight of oxygen from the reduction of copper. Bi(2+x)Sr(2-y) CuO6, Bi(2+n)(Sr,Ca)(3-y) Cu2O8, and Bi(2+x)(Sr,Ca)(4-y) Cu3O10 exhibit crystallographic alignment in a magnetic field, with the c-axes orienting parallel to the field.

Deguire, Mark R.↗
NASA NTRS1991

Environmental fatigue of an Al-Li-Cu alloy. Part 1: Intrinsic crack propagation kinetics in hydrogenous environments

Deleterious environmental effects on steady-state, intrinsic fatigue crack propagation (FCP) rates (da/dN) in peak aged Al-Li-Cu alloy 2090 are established by electrical potential monitoring of short cracks with programmed constant delta K and K(sub max) loading. The da/dN are equally unaffected by vacuum, purified helium, and oxygen but are accelerated in order of decreasing effectiveness by aqueous 1 percent NaCl with anodic polarization, pure water vapor, moist air, and NaCl with cathodic polarization. While da/dN depends on delta K(sup 4.0) for the inert gases, water vapor and chloride induced multiple power-laws, and a transition growth rate 'plateau'. Environmental effects are strongest at low delta K. Crack tip damage is ascribed to hydrogen embrittlement because of the following: (1) accelerated da/dN due to part-per-million levels of H2O without condensation; (2) impeded molecular flow model predictions of the measured water vapor pressure dependence of da/dN as affected by mean crack opening; (3) the lack of an effect of film-forming O2; (4) the likelihood for crack tip hydrogen production in NaCl, and (5) the environmental and delta K-process zone volume dependencies of the microscopic cracking modes. For NaCl, growth rates decrease with decreasing loading frequency, with the addition of passivating Li2CO3, and upon cathodic polarization. These variables increase crack surface film stability to reduce hydrogen entry efficiency. The hydrogen environmental FCP resistance of 2090 is similar to other 2000 series alloys and is better than 7075.

Piascik, Robert S.↗
NASA NTRS1991

Evaluation of the microstructure of Al-Cu-Li-Ag-Mg Weldalite (tm) alloys, part 4

Weldalite (trademark) 049 is an Al-Cu-Li-Ag-Mg alloy designed to have ultrahigh strength and to serve in aerospace applications. The alloy displays significantly higher strength than competitive alloys in both naturally aged and artificially aged tempers. The strengthening phases in such tempers have been identified to, in part, explain the mechanical properties attained. In general, the alloy is strengthened by delta prime Al3Li and Guinier-Preston (GP) zones in the naturally aged tempers. In artificially aged tempers in slightly underaged conditions, strengthening is provided by several phases including GP zones, theta prime Al2Cu, S prime Al2CuMg, T(sub 1) Al2CuLi, and possibly a new phase. In the peak strength artificially aged tempers, T(sub 1) is the predominant strengthening phase.

Pickens, Joseph R.↗
NASA NTRS1991

Structure and properties during aging of an Al-Cu-Li-Ag-Mg alloy, Weldalite (tm) 049

An Al-Cu-Li-Ag-Mg alloy, Weldalite (trademark) 049, was recently introduced as an ultra-high strength alloy (7000 MPa yield strength in artificially aged tempers) with good weldability. In addition, the alloy exhibits an extraordinary natural aging response (440 MPa yield strength (YS) in the unstretch condition) and a high ductility reversion condition which may be useful as a cold-forming temper. In contrast to other Al-Li alloys, these properties can essentially be obtained with or without a stretch or other coldworking operation prior to aging. Preliminary studies have revealed that the T4 temper (no stretch, natural age) is strengthened by a combination of GP zones and delta prime (Al3Li). The T6 temper (no stretch, aged at 180 C to peak strength) was reported to be strengthened primarily by T(sub 1) phase (Al2CuLi) with a minor presence of a theta prime like (Al2Cu) phase. On the other hand, a similar but lower solute containing alloy was reported to contain omega, (stoichiometry unknown), theta prime, and S prime in the peak strength condition. The purpose of this study is to further elucidate the strengthening phases in Weldalite (trademark) 049 in the unstretched tempers, and to follow the development of the microstructure from the T4 temper through reversion (180 C for 5 to 45 minutes) to the T6 temper.

Gayle, Frank W.↗
NASA NTRS1991

Microstructure-property relationships in Al-Cu-Li-Ag-Mg Weldalite (tm) alloys, part 2

The microstructure and mechanical properties of the ultrahigh strength Al-Cu-Li-Ag-Mg alloy, Weldalite (tm) 049, were studied. Specifically, the microstructural features along with tensile strength, weldability, Young's modulus and fracture toughness were studied for Weldalite (tm) 049 type alloys with Li contents ranging from 1.3 to 1.9 wt. pct. The tensile properties of Weldalite 049 and Weldalite 049 reinforced with TiB2 particles fabricated using the XD (tm) process were also evaluated at cryogenic, room, and elevated temperatures. In addition, an experimental alloy, similar in composition to Weldalite 049 but without the Ag+Mg, was fabricated. The microstructure of this alloy was compared with that of Weldalite 049 in the T6 condition to assess the effect of Ag+Mg on nucleation of strengthening phases in the absence of cold work.

Langan, T. J.↗
NASA NTRS1991

The influence of Ag+Mg additions on the nucleation of strengthening precipitates in a non-cold-worked Al-Cu-Li alloy

Aluminum-copper-lithium alloys generally require cold work to attain their highest strengths in artificially aged tempers. These alloys are usually strengthened by a combination of the metastable delta prime (Al3Li) and theta prime (Al2Cu) phases and the equilibrium T sub 1 (Al2CuLi) phase, and where the T sub 1 phase is a more potent strengthener than the delta prime. Various investigators have shown that the high strengths obtained after artificial aging associated with cold work result from the heterogeneous precipitation of T sub 1 on matrix dislocations. The objective here is to elucidate the mechanism by which the Ag+Mg additions stimulate the precipitation of T sub 1 type precipitates without cold work. To accomplish this, the microstructure of an Al-6.3Cu-1.3Li-0.14Zr model alloy was evaluated in a T6 type temper with and without the Ag+Mg addition.

Source record↗
NASA NTRS1990

Theoretical study of the homonuclear tetramers and pentamers of the group IB metals (Cu, Ag, and Au)

The optimal structures of the homonuclear tetramers and pentamers of Cu, Ag, and Au are found to be planar trapezoidal. However, on the basis of spin densities deduced from electron spin resonance experiments, it has been suggested that these pentamers have distorted trigonal bipyramidal structures. This apparent discrepancy is reconciled by the fact that Mulliken populational analyses indicate that the open-shell spin density distribution on the planar structures are also consistent with experiment. Since the vertical electron attachment energies for both the tetramers and pentamers are in good agreement with experiment, the negative ions probably also have planar trapezoidal structures. The trends in ionization potentials, atomization energies, and electron affinities with cluster size are discussed.

Bauschlicher, Charles W., Jr.↗
NASA NTRS1990

Electrical transport measurements on polycrystalline superconducting Y-Ba-Cu-O films

The current-voltage, I-V, characteristics of polycrystalline Y-Ba-Cu-O films have been measured as a function of temperature. The I-V characteristics are interpreted using a model based upon an array of weak links with a statistical distribution of critical currents. In addition, evidence is found that the supercurrents flow in nearly independent filaments near Tc. Various criteria are discussed with respect to the definition of the transport critical current, Ic, in these films. A temperature dependence for Ic has also been deduced from the I-V data by appealing to an empirical scaling law. It is proposed that this temperature dependence is representative of the weaker links within the critical current distribution.

Stan, M. A.↗
NASA NTRS1991

Relative populations of excited levels within the ground configuration of Si-like Cu, Zn, Ge and Se ions

Populations of 3p2 1D2, 3P1, 3P2 levels in Si-like Cu, Zn, Ge, and Se ions have been deduced from the measurements of absolute intensities of magnetic dipole transitions within the 3s2 3p2 ground configuration. The measured population ratios are compared with theoretical calculations based on the distorted-wave approximation for the electron collisions and a semiclassical approximation for the proton collisions. The observed deviation from the statistical distribution for the excited-level populations within the ground configuration along the silicon isoelectronic sequence is in agreement with theoretical prediction.

Datla, R. U.↗
NASA NTRS1991

Synthesis and superconducting properties of Tl-Ba-Ca-Cu-O films

Tl-Ba-Ca-Cu-O superconducting films were synthesized by sputtering either from a single target or from two oxide targets in a symmetric configuration. Films with zero resistance Tc of up to 122 K were obtained after various postannealing treatments at 870-950 C under an oxygen atmosphere. The composition of the films is not very homogeneous on the submicrometer scale. The critical current of these films at 77 K is in the 1000 A/sq cm to 10,000 A/sq cm range, which is much smaller than that of films prepared on SrTiO3 and LaAlO3 substrates. The low critical current density in these films is probably due to the granularity in the films. The morphology, structure, and magnetic and superconducting properties of the films were studied. Films prepared by two different sputtering techniques have similar results which depend mostly on the film compositions and their annealing conditions. It is found that the induced magnetic flux in the film decreases rapidly with increasing temperature, indicating weak flux pinning.

Liou, S. H.↗
NASA NTRS1991

Stability of Y-Ba-Cu-oxide phases in salt flux

The results of an investigation into the possibility of growing YBa2Cu3O7 (or Y123) single crystals from a NaCl-KCl flux (salt flux) are presented. They are compared with results for Y123 crystals grown from a Ba-Cu-oxide flux system. The chosen salt flux composition was 1:1 (NaCl:KCl). The preparation method of the solutes is presented, with particular attention given to the compounds surrounding the Y123 phase, such as Y2BaCuO6 (Y211). Optical microscopy was introduced to study the morphology of the sample; X-ray diffraction was used for phase identification; and a chemical analysis was effected. The Y123, Y211, and BaCuO2 phases were shown to be dissociated in the NaCl-KCl flux, and could not be recrystallized. A small amount of the flux could be added to create large-grain Y123 crystals, but single-crystal growth was not possible in a top-seeded NaCl-KCl solution. This is attributed to significant differences in solubility of the crystal elements, and phase separation caused by CuO crystal formation.

Tao, Y. K.↗
NASA NTRS1989

Identification of strengthening phases in Al-Cu-Li alloy Weldalite 049

The tensile properties in the peak-strength T8 temper for Weldalite 049, a family of ultrahigh-strength weldable Al-Cu-Li-based alloys with a Li content ranging from 0 to 1.9 wt percent, are investigated, and strengthening precipitates at selected Li levels are identified. Relatively small amounts of Ag and Mg were found to be extremely effective in stimulating precipitation in Weldalite 049, resulting in a homogeneous distribution of fine, platelike precipitates with a 111-type habit plane in the peak-aged, T8 temper. The yield and tensile strengths are strongly dependent on Li content, with a peak in the range of 1.1 to 1.4 wt percent Li. At above 1.4 wt percent Li, strength decreases rapidly, which is associated with delta-prime precipitation. For high-resolution TEM, the structure of T(1)-type precipitates in Weldalite 049 is similar to that of T(1) platelets in 2090.

Langan, T. J.↗
NASA NTRS1991

Sputtered Ta-Si-N diffusion barriers in Cu metallizations for Si

Electrical measurements on shallow Si n+-p junction diodes with a 30-nm TiSi2 contacting layer demonstrate that an 80-nm-thick amorphous Ta36Si14N50 film prepared by reactive RF sputtering of a Ta5Si3 target in an Ar/N2 plasma very effectively prevents the interaction between the Si substrate with the TiSi2 contacting layer and a 500-nm Cu overlayer. The Ta36Si14N50 diffusion barrier maintains the integrity of the I-V characteristics up to 900 C for 30-min annealing in vacuum. It is concluded that the amorphous Ta36Si14N50 alloy is not only a material with a very low reactivity for copper, titanium, and silicon, but must have a small diffusivity for copper as well.

Kolawa, E.↗
NASA NTRS1991

The effect of TiB2 reinforcement on the mechanical properties of an Al-Cu-Li alloy-based metal-matrix composite

Weldalite 049, an Al-base Cu-Li-Mg-Ag-Zr alloy, achieves 700 MPa tensile strengths in the near-peak-aged temper in virtue of the nucleation of a T(1)-type platelike strengthening precipitate. Attention is presently given to the possibility that the alloy's modulus could be further increased through the addition of high-modulus TiB2 particles, using the 'XD' process, due to TiB2's good wettability with liquid Al. An 8-percent modulus increase is obtained with 4 vol pct TiB2.

Langan, T. J.↗
NASA NTRS1991

Creep behaviour of Cu-30 percent Zn at intermediate temperatures

The present, intermediate-temperature (573-823 K) range investigation of creep properties for single-phase Cu-30 percent Zn alpha-brass observed inverse, linear, and sigmoidal primary-creep transients above 573 K under stresses that yield minimum creep rates in the 10 to the -7th to 2 x 10 to the -4th range; normal primary creep occurred in all other conditions. In conjunction with a review of the pertinent literature, a detailed analysis of these data suggests that no clearly defined, classes M-to-A-to-M transition exists in this alloy notwithstanding the presence of both classes' characteristics under nominally similar stresses and temperatures.

Raj, S. V.↗
NASA NTRS1990

Pulsed laser deposition of Tl-Ca-Ba-Cu-O films

Pulsed laser deposition is a technique commonly used to deposit high quality thin films of high temperature superconductors. This paper discusses the results obtained when this technique is applied to the deposition of Tl-Ca-Ba-Cu-O thin films using a frequency doubled Nd:YAG laser operating at 532 nm and an excimer laser operating at 248 nm. Films with onset temperatures of 125 K and zero resistance temperatures of 110 K deposited on (100) oriented MgO from a composite Tl2Ca2Ba2Cu3Ox target were obtained at both wavelengths upon appropriate post deposition annealing. Films deposited at 532 nm exhibit a rough surface, while those deposited at 248 nm are smooth and homogeneous. Upon annealing, films deposited at both wavelengths are single phase Tl2Ca2Ba2Cu3Ox.

Ianno, N. J.↗
NASA NTRS1990

High Tc superconducting IR detectors from Y-Ba-Cu-O thin films

A thin-film high-Tc superconducting multielement optical detector made of Y-Ba-Cu-O has been designed and evaluated using optical pulses from a diode laser (830 nm) and a Q-switched CO2-laser (10.6 microns). Different thin films have been tested. A laser deposited film showed the strongest response amplitude for short pulses and responded to an ultrafast, 50 ps wide pulse. Comparisons between dR/dT and response as a function of temperature indicated, however, a bolometric response.

Lindgren, M.↗
NASA NTRS1991

Environmental fatigue of an Al-Li-Cu alloy. I - Intrinsic crack propagation kinetics in hydrogenous environments

Deleterious environmental effects on steady-state, intrinsic fatigue crack propagation (FCP) rates (da/dN) in peak aged Al-Li-Cu alloy 2090 are established by electrical potential monitoring of short cracks with programmed constant delta K and K(sub max) loading. The da/dN are equally unaffected by vacuum, purified helium, and oxygen but are accelerated in order of decreasing effectiveness of aqueous 1 percent NaCl with anodic polarization, pure water vapor, moist air, and NaCl with cathodic polarization. While da/dN depends on delta K(sup 4.0) for the inert gases, water vapor and chloride induced multiple power-laws, and a transition growth rate 'plateau'. Environmental effects are strongest at low delta K. Crack tip damage is ascribed to hydrogen embrittlement because of the following: (1) accelerated da/dN due to part-per-million levels of H2O without condensation; (2) impeded molecular flow model predictions of the measured water vapor pressure dependence of da/dN as affected by mean crack opening; (3) the lack of an effect of film-forming O2; (4) the likelihood for crack tip hydrogen production in NaCl; and (5) the environmental and delta K-process zone volume dependencies of the microscopic cracking modes. For NaCl, growth rates decrease with decreasing loading frequency, with the addition of passivating Li2CO3, and upon cathodic polarization. These variables increase crack surface film stability to reduce hydrogen entry efficiency. The hydrogen environmental FCP resistance of 2090 is similar to other 2000 series alloys and is better than 7075.

Piascik, Robert S.↗