Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Detector Characterization for Quantitative Spectral Radiography of Uranium Powder Samples

Pacific Northwest National Laboratory (PNNL) is developing a prototype spectral x-ray radiography (SpecX) non-destructive assay system for noninvasive material mass quantification of uranium-bearing powders. The SpecX system uses a custom material estimation algorithm, which requires a high-fidelity pixel-by-pixel detector response model for accurate quantification. We performed a detailed characterization and built a model of a High-Energy X-ray Imaging Technology (HEXITEC) CdTe pixelated spectral detector. Here we present the detector characterization which led to that model, including a determination of the pixel-wise energy calibration, the detection efficiency, the detector uniformity, the detector stability, and a comparison of methods to remove charge-shared events.

spectral X-ray radiography, pixelated detector, ca↗

Separation, Characterization and Initial Reaction Studies of Magnetite Particles from Hanford Sediments

Magnetic and density separation methods have been applied to composite sediment sample from the Hanford formation from sediment recovered during drilling of an uncontaminated borehole located near the 200 West Area of the Hanford Site in southeastern Washington State. This paper describes the results of using those separation methods and from the characterization and initial reactivity measurements on a highly magnetic fraction isolated from that sediment. X-ray diffraction (XRD) analysis of the highly magnetic sediment fraction indicates that this material contains predominantly magnetite (Fe3O4). Particle morphology observed by scanning electron microscopy (SEM) and compositions determined energy dispersive spectroscopy (EDS) are consistent with this identification. Analyses by X-ray photoelectron spectroscopy (XPS) indicates that there is a thin coating on the particles that are likely a type of aluminosilicate. This highly magnetic fraction of material is not reactive with indigo carmine, an organic redox probe molecule that was shown to readily react with synthetic magnetite. Because of the limited amounts of material readily available, initial tests have been conducted that demonstrate the ability to complete U(VI) sorption on individual particles (nominally ~100 µm in size) of the isolated sediment and to remove and mount these individual particles for analysis of the concentration and chemical state of the sorbed U species using small area XPS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterizing the lipid and metabolite changes associated with placental function and pregnancy complications using ion mobility spectrometry-mass spectrometry and mass spectrometry imaging

Successful pregnancy is dependent upon discrete biological events, which include embryo implantation, decidualization, and placentation. Problems associated with each of these events can cause infertility or conditions such as preeclampsia. A greater understanding of the molecular changes associated with these complex processes is necessary to aid in identifying treatments for each condition. Previous nuclear magnetic resonance spectroscopy and mass spectrometry studies have been used to identify metabolites and lipids associated with pregnancy-related complications. However, due to limitations associated with conventional implementations of both techniques, novel technology developments are needed to more fully understand the initiation and development of pregnancy related problems at the molecular level. In this perspective, we describe current analytical techniques for metabolomic and lipidomic characterization of pregnancy complications and discuss the potential for new technologies such as ion mobility spectrometry-mass spectrometry and mass spectrometry imaging to contribute to a better understanding of the molecular changes that affect the placenta and pregnancy outcomes.

Environmental Molecular Sciences Laboratory↗

BEAM: A Computational Workflow System for Managing and Modeling Material Characterization Data in HPC Environments

Improvements in scientific instrumentation allow imaging at mesoscopic to atomic length scales, many spectroscopic modes, and now—with the rise of multimodal acquisition systems and the associated processing capability—the era of multidimensional, informationally dense data sets has arrived. Technical issues in these combinatorial scientific fields are exacerbated by computational challenges best summarized as a necessity for drastic improvement in the capability to transfer, store, and analyze large volumes of data. The Bellerophon Environment for Analysis of Materials (BEAM) platform provides material scientists the capability to directly leverage the integrated computational and analytical power of High Performance Computing (HPC) to perform scalable data analysis and simulation via an intuitive, cross-platform client user interface. This framework delivers authenticated, “push-button” execution of complex user workflows that deploy data analysis algorithms and computational simulations utilizing the converged compute-and-data infrastructure at Oak Ridge National Laboratory's (ORNL) Compute and Data Environment for Science (CADES) and HPC environments like Titan at the Oak Ridge Leadership Computing Facility (OLCF). In this work we address the underlying HPC needs for characterization in the material science community, elaborate how BEAM's design and infrastructure tackle those needs, and present a small sub-set of user cases where scientists utilized BEAM across a broad range of analytical techniques and analysis modes.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

Geospatial characterization of low-temperature heating and cooling demand in residential, commercial, manufacturing, agricultural, and data center sectors for potential geothermal applications in the United States

Thermal demand for heating and cooling has been predominantly supplied by fossil fuel combustion in the United States, although low-carbon alternatives are extensively available including geothermal, solar thermal, and waste heat. Here, this study analyzed end-use energy consumption, fuel expenditure, and data center commissioned power data to geospatially characterize the U.S. low-temperature heating and cooling demand at the county level in residential, commercial, manufacturing, agricultural, and data center sectors and understand potential opportunities for geothermal applications. In the analysis, the regional-scale energy consumption data was incorporated with system efficiencies to address actual demand and was then disaggregated with weighting factors to the county level. The results indicated that total low-temperature heating and cooling demand is 16.7 EJ, combining heating demand of 10.8 EJ and cooling demand of 5.9 EJ. Overall, 59.9 % (10 EJ) of the low-temperature heating and cooling demand occurred in the residential sector. The heating and cooling demand visualized in maps represented that the geospatial distribution of heating and cooling demand in the residential and commercial sectors is governed by the number of housing units and climate zone designations, while heating and cooling demand in the manufacturing, agricultural, and data center sectors is dependent on the number and location of facilities. The results also demonstrated that geothermal heat pumps are broadly used in the residential and commercial sectors for heating and cooling in the U.S. Midwest, South, and Northeast regions but are limited in the West, implying great decarbonization potential in the future.

15 GEOTHERMAL ENERGY↗

PTMSearchPlus: Software Tool for Automated Protein Identification and Post-Translational and Post-Translational Modification Characterization by Integrating Accurate Intact Protein Mass and Bottom-Up Mass Spectrometric Data Searches

PTMSearchPlus is a software tool for the automated integration of accurate intact protein mass (AIPM) and bottom-up (BU) mass spectra searches/data in order to both confidently identify the intact proteins and to characterize their post-translational modifications (PTMs). The development of PTMSearchPlus was motivated by the desire to effectively integrate high-resolution intact protein molecular masses with bottom-up peptide MS/MS data. PTMSearchPlus requires as input both intact protein and proteolytic peptide mass spectra collected from the same protein mixture, a FASTA protein database, and a selection of possible PTMs, the types and ranges of which can be specified. The output of PTMSearchPlus is a list of intact and modified proteins matching the AIPM data concomitant with their respective peptides found by the BU search. This list also contains protein and peptide sequence coverage information, scores, etc. that can be used for further evaluation or refiltering of the results. Corresponding and annotated AIPM and BU mass spectra are also displayed for visual inspection when a listed protein or a peptide is selected. These and other controls ensure that the user can manually evaluate, modify (e.g., remove obvious false positives, low quality spectra etc.), and save the results of the automated search if necessary. Driven by the exponential growth in the number of possible peptide candidates in a BU search when multiple PTMs are probed, the advantages on search speed by limiting the total number of possible PTMs on a peptide in the BU search or by performing an AIPM predicted BU search are also discussed in addition to the integration approach. The features of PTMSearchPlus are demonstrated using both a protein standard mixture and a complex protein mixture from Escherichia coli. Experimental data revealed a unique advantage of coupling AIPM and the BU data sets that is mutually beneficial for both approaches. Namely, AIPM data can confirm that no PTM peptides were missed in a BU search, while the BU search determines the location of the PTM. This information is not available using an AIPM search alone.

59 BASIC BIOLOGICAL SCIENCES↗

β-Hydroxyacyl-acyl Carrier Protein Dehydratase (FabZ) from Francisella tularensis and Yersinia pestis : Structure Determination, Enzymatic Characterization, and Cross-Inhibition Studies

The bacterial system for fatty acid biosynthesis (FAS) contains several enzymes whose sequence and structure are highly conserved across a vast array of pathogens. This, coupled with their low homology and difference in organization compared to the equivalent system in humans, makes the FAS pathway an excellent target for antimicrobial drug development. To this end, we have cloned, expressed, and purified the β-hydroxyacyl-acyl carrier protein dehydratase (FabZ) from both Francisella tularensis (FtFabZ) and Yersinia pestis (YpFabZ). We also solved the crystal structures and performed an enzymatic characterization of both enzymes and several mutant forms of YpFabZ. Additionally, we have discovered two novel inhibitors of FabZ, mangostin and stictic acid, which show similar potencies against both YpFabZ and FtFabZ. Lastly, we selected several compounds from the literature that have been shown to be active against single homologues of FabZ and tested them against both YpFabZ and FtFabZ. These results have revealed clues as to which scaffolds are likely to lead to broad-spectrum antimicrobials targeted against FabZ as well as modifications to existing FabZ inhibitors that may improve potency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis and Characterization of MgCr 2 S 4 Thiospinel as a Potential Magnesium Cathode

Magnesium-ion batteries are a promising energy storage technology because of their higher theoretical energy density and lower cost of raw materials. Among the major challenges has been the identification of cathode materials that demonstrate capacities and voltages similar to lithium-ion systems. Thiospinels represent an attractive choice for new Mg-ion cathode materials owing to their interconnected diffusion pathways and demonstrated high cation mobility in numerous systems. Reported magnesium thiospinels, however, contain redox inactive metals such as scandium or indium, or have low voltages, such as MgTi 2 S 4 . This article describes the direct synthesis and structural and electrochemical characterization of MgCr 2 S 4 , a new thiospinel containing the redox active metal chromium and discusses its physical properties and potential as a magnesium battery cathode. However, as chromium(III) is quite stable against oxidation in sulfides, removing magnesium from the material remains a significant challenge. Finally, early attempts at both chemical and electrochemical demagnesiation are discussed.

25 ENERGY STORAGE↗

Characterizing the Mechanisms of Ca and Mg Carbonate Ion-Pair Formation with Multi-Level Molecular Dynamics/Quantum Mechanics Simulations

The carbonate minerals of Ca and Mg are abundant throughout the lithosphere and have recently garnered significant research interest as possible long-term carbon sinks in the sequestration of atmospheric carbon dioxide. Nonetheless, an understanding of the atomic-level processes comprising their mineralization remains limited. Furthermore, we characterize and contrast the mechanisms of contact ion-pair formation in aqueous Ca and Mg carbonate systems, which represents the most fundamental step leading to the formation of their mineral solids. Utilizing multilevel embedded correlated wavefunction-based ab initio molecular dynamics/quantum mechanics simulations, we characterize not only the dynamics of these processes but also factors arising from the electronic structure of the involved species, revealing further details of the fundamentally different mechanisms for the interconversion between the contact ion-pairs and solvent-shared ion-pairs of Ca versus Mg carbonate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In-situ Characterization of Cu/CeO 2 Nanocatalysts during CO 2 Hydrogenation: Morphological Effects of Nanostructured Ceria on the Catalytic Activity

Here, a combination of time-resolved X-ray diffraction (TR-XRD), ambient-pressure X-ray photoelectron spectroscopy (AP-XPS) and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) was used to carry out an in-situ characterization of Cu/CeO 2 nanocatalysts during the hydrogenation of CO 2 . Morphological effects of the ceria supports on the catalytic performances were investigated by examining the behavior of copper/ceria-nanorods (NR) and nanospheres (NS). At atmospheric pressures, the hydrogenation of CO 2 on the copper-ceria catalysts produced mainly CO through the reverse-water gas shift reaction (RWGS) and a negligible amount of methanol. The Cu/CeO 2 -NR catalyst displayed the higher activity, which demonstrates that the RWGS is a structure sensitive reaction. In-situ TR-XRD and AP-XPS characterization showed significant changes in the chemical state of the catalysts under reaction conditions with the copper being fully reduced and a partial Ce 4+ to Ce 3+ transformation occurring. A more effective CO 2 dissociative activation at high temperature and a preferential formation of active bidentate carbonate and formate intermediates over CeO 2 (110) terminations are probably the main reasons for the better performance of the Cu/CeO 2 -NR catalyst in the RWGS reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Iridium Atoms Bonded to Crystalline Powder MgO: Characterization by Imaging and Spectroscopy

Samples with low loadings of metals on well-defined supports provide some of the best opportunities to determine the metal–support structure and bonding. We illustrate methods for characterizing atomically dispersed heavy metals on metal oxide supports by aberration-corrected scanning transmission electron microscopy (STEM) complemented by fluorescence detection extended X-ray absorption fine structure and infrared spectroscopies. STEM images of Ir atoms derived from Ir(C 2 H 4 ) 2 (acac) (acac = acetylacetonato) on high-surface-area MgO powder were obtained with minimized electron beam damage by quickly recording images near where the focus had been established. The images show that iridium at a loading of 1.0 wt % on MgO calcined at 1073 K was atomically dispersed, populating much of the surface of the MgO particles, which had irregular shapes—consequently the Ir atoms were bonded at various sites to two or three surface O atoms. In contrast, MgO calcined at 1273 K consisted of almost perfectly cubic crystals, and Ir atoms at a loading of only 0.01 wt % on this nearly ideal support were anchored preferentially at edges and corners of the (100) faces and bonded to three surface O atoms. The latter results indicate a path forward for the determination of precise structures of atomically dispersed metals on crystalline metal oxide supports.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Neutrally Charged Trimethylmanganese(III) Complex: Synthesis, Characterization, and Disproportionation Chemistry

The synthesis and properties of an unusual, neutrally charged and volatile N,N,N',N'-tetramethylethylenediamine trimethyl manganese(III) complex, (TMEDA)MnMe 3 , are described, along with its facile disproportionation to the corresponding Mn(II) and Mn(IV) complexes. Characterization by single-crystal XRD, UV-vis spectroscopy, high-frequency and -field EPR (HFEPR), magnetic susceptibility, and density functional theory (DFT) computations indicate that the (TMEDA)MnMe3 electronic structure can be described as largely square pyramidal Mn(III) centered. The paucity of manganese(III) polyalkyls and the simplicity and reactivity of this compound implicate it as a potentially useful synthetic building block.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Online Characterization of Mixed Plastic Waste Using Machine Learning and Mid-Infrared Spectroscopy

To recycle the mixed plastic wastes (MPW), it is important to obtain the compositional information online in real time. We present a sensing framework based on a convolutional neural network (CNN) and mid-infrared spectroscopy (MIR) for the rapid and accurate characterization of MPW. The MPW samples are placed on a moving platform to mimic the industrial environment. The MIR spectra are collected at the rate of 100 Hz, and the proposed CNN architecture can reach an overall prediction accuracy close to 100%. Therefore, the proposed method paves the way toward the online MPW characterization in industrial applications where high throughput is needed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Physiochemical Characterization of Lignocellulosic Biomass Dissolution by Flowthrough Pretreatment

Comprehensive understanding of biomass solubilization chemistry in aqueous pretreatment such as water-only and dilute acid flowthrough pretreatment is of fundamental importance to achieve the goal of valorizing biomass to fermentable sugars and lignin for biofuels production. In this study, poplar wood was flowthrough pretreated by water-only or 0.05% (w/w) sulfuric acid at different temperatures (220-270 °C), flow rate (25 mL/min), and reaction times (8-90 min), resulting in significant disruption of the lignocellulosic biomass. Ion chromatography (IC), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) analysis, and solid state cross-polarization/magic angle spinning (CP/MAS) 13C nuclear magnetic resonance (NMR) spectroscopy were applied to characterize the pretreated biomass whole slurries in order to reveal depolymerization as well as solubilization mechanism and identify unique dissolution structural features during these pretreatments. Results showed temperature-dependent cellulose decrystallization in flowthrough pretreatment. Crystalline cellulose was completely disrupted, and mostly converted to amorphous cellulose and oligomers by water-only operation at 270 °C for 10 min and by 0.05 wt % H2SO4 flowthrough pretreatment at 220 °C for 12 min. Flowthrough pretreatment with 0.05% (w/w) H2SO4 led to a greater disruption of structures in pretreated poplar at a lower temperature compared to water-only pretreatment.

54 ENVIRONMENTAL SCIENCES↗

Characterization and Reactivity of Iron Nanoparticles Prepared with Added Cu, Pd, and Ni

The presence of a secondary metal on iron particles affects redox reactivity in engineered remediation systems. However, the structural characteristics of the metal additives and mechanism responsible for changes in reactivity have not been fully elucidated. Here, we synthesized iron nanoparticles with Cu, Pd, and Ni content ranging from 0-2 mol% via a solution deposition process (SDP), hydrogen reduction process (HRP), or hydrogen reduction of ferrihydrite coprecipitated with the metal cations (HRCO). Results from solid-state characterization show that the synthetic methods produced similar iron core/magnetite shell particles but produced substantial differences in terms of the distribution of the metal additive. In SDP, the metal additives were heterogeneous distributed on the surface of the particles. The metal additives were clearly discernable in TEM images as spherical nanoparticles (2-4 nm) on the HRP and HRCO particles. In addition, we hypothesize that the metal additive is also present as solute within the iron core of the HRCO particles. Kinetic batch experiments of carbon tetrachloride (CT) degradation were performed to quantitatively compare the redox reactivity of the particles. Overall, metal additives resulted in enhanced overall pseudo-first order rate constants of CT degradation (kO,CT) compared to that of the iron nanoparticles. For the bimetallic iron nanoparticles prepared by SDP and HRP, kO,CT increased with the concentration of metal additives. The values of chloroform yield (YCF) were independent of the identity and amount of metal additives. However, both kO,CT and YCF of the HRCO iron particles were significantly greater. Results suggest that it is the distribution of the metal additives that most strongly impacts reactivity and product distribution. For example, for materials with ca. 0.9 50 mol% Ni, reactivity and YCF varied substantially (HRCO>SDP>HRP), and HRCO-NiFe resulted in the lowest final chloroform concentration because the chloroform was rapidly dechlorinated. In addition, sequential spike experiments for long-term reactivity demonstrated that the presence of the metal additives facilitated reduction by enabling greater utilization of Fe0.

54 ENVIRONMENTAL SCIENCES↗

Synthesis and Characterization of Thiazolium-Based Room Temperature Ionic Liquids for Gas Separations

A series of novel thiazolium-bis(triflamide) based ionic liquids has been synthesized and characterized. Physicochemical properties of the ionic liquids such as thermal stability, phase transitions, and infrared spectra were analyzed and compared to the imidazolium-based congeners. Several unique classes of ancillary substitutions are examined with respect to impacts on overall structure, in addition to their carbon dioxide absorption properties in supported ionic-liquid membranes for gas separation.

Hillesheim, PC↗