Results for “CONE” — Page 11

NASA NTRS1961

Experimental Determination of the Recovery Factor and Analytical Solution of the Conical Flow Field for a 20 deg Included Angle Cone at Mach Numbers of 4.6 and 6.0 and Stagnation Temperatures to 2600 degree R

The local recovery factor was determined experimentally along the surface of a thin-walled 20 deg included angle cone for Mach numbers near 6.0 at stagnation temperatures between 1200 deg R and 2600 deg R. In addition, a similar cone configuration was tested at Mach numbers near 4.5 at stagnation temperatures of approximately 612 deg R. The local Reynolds number based on flow properties at the edge of the boundary layer ranged between 0.1 x 10(exp 4) and 3.5 x 10(exp 4) for tests at temperatures above 1200 deg R and between 6 x 10(exp 4) and 25 x 10(exp 4) for tests at temperatures near 612 deg R. The results indicated, generally, that the recovery factor can be predicted satisfactorily using the square root of the Prandtl number. No conclusion could be made as to the necessity of evaluating the Prandtl number at a reference temperature given by an empirical equation, as opposed to evaluating the Prandtl number at the wall temperature or static temperature of the gas at the cone surface. For the tests at temperatures above 1200 deg R (indicated herein as the tests conducted in the slip-flow region), two definite trends in the recovery data were observed - one of increasing recovery factor with decreasing stagnation pressure, which was associated with slip-flow effects and one of decreasing recovery factor with increasing temperature. The true cause of the latter trend could not be ascertained, but it was shown that this trend was not appreciably altered by the sources of error of the magnitude considered herein. The real-gas equations of state were used to determine accurately the local stream properties at the outer edge of the boundary layer of the cone. Included in the report, therefore, is a general solution for the conical flow of a real gas using the Beattie-Bridgeman equation of state. The largest effect of temperature was seen to be in the terms which were dependent upon the internal energy of the gas. The pressure and hence the pressure drag terms were unaffected.

Pfyl, Frank A.↗

NASA NTRS2002

Origins of Small Volcanic Cones on Mars

Studies of volcanic cones identified in the MGS data indicate a range of possible origins, from primary vent constructs (cinder cones, tuff cones) to rootless cones formed by lava-ice interaction. Additional information is contained in the original extended abstract.

Fagents, S. A.↗

NASA NTRS2003

Icelandic Pseudocraters as Analogs to some Volcanic Cones on Mars

Pseudocraters are rootless vents formed by the interaction of lava flows with surface or near-surface water. This interaction can produce mild explosions and the accumulation of scoria and spatter into small constructs. Pseudocraters in several localities in Iceland were examined in the field and compared to similar appearing features observed on Mars. The Icelandic pseudocrater cones in this study range in size from 6 to 70 m in diameter, have summit craters which range from 2 to 28 m in diameter (many cones lack craters entirely), and have flanks that am either concave- up or convex-up. The size and spacing of Icelandic pseudo-craters might be a function of the availability of water, in which larger, closely spaced features result from efficient lava-water interaction, as suggested by the environments in which the features formed. Possible Martian pseudocrater cones in Amamnis Planitia range in diameter from 30 to 180 m and have craters 12 to 80 m in diameter. A numerical model for volcanic explosions was adapted to study the formation of pseudocraters under terrestrial and Martian conditions. The results suggest that explosions forming Martian cones require significantly less water (calculated masses am less by a factor of 4 to 16) than those forming Icelandic pseudokers, despite their larger sizes, This is attributed to the low gravity and atmospheric pressure in the Mars environment and is consistent with the likely lower abundance of water, which might be present as interstitial ice at shallow depths in the regolith. Locations of potential pseudocraters on Mars at latitudes as low as approximately 8 degrees N, imply the presence of crustal ice stores at the time of their formation.

Greeley, Ronald↗

NASA NTRS2007

Receptivity of Supersonic Boundary Layers Due To Acoustic Disturbances Over Blunt Cones

Receptivity and stability of supersonic boundary layers over a 5-degree straight cone with a blunt tip are numerically investigated at a free stream Mach number of 3.5 and at a high Reynolds number of 106/inch. Both the steady and unsteady solutions are obtained by solving the full Navier-Stokes equations using the 5th-order accurate weighted essentially non-oscillatory (WENO) scheme for space discretization and using third-order total-variation-diminishing (TVD) Runge-Kutta scheme for time integration. The linear stability results showed that bluntness has less stabilizing effects on the stability of boundary layers over cones than on flat plates and wedges. The unsteady simulations of the interaction of plane threedimensional acoustic waves with the cone showed that the modulation of wavelength and the generation of instability waves first occurred near the leading edge in the plane where the constant acoustic phase lines are perpendicular to the cone axis. Further downstream, this instability region spreads in the azimuthal direction from this plane.

Balakumar, P.↗

NASA NTRS2009

Stability of Supersonic Boundary Layers on a Cone at an Angle of Attack

The stability and receptivity of three-dimensional supersonic boundary layers over a 7deg sharp tipped straight cone at an angle of attack of 4.2deg is numerically investigated at a free stream Mach number of 3.5 and at two high Reynolds numbers, 0.25 and 0.50x10(exp 6)/inch. The generation and evolution of stationary crossflow vortices are also investigated by performing simulations with three-dimensional roughness elements located on the surface of the cone. The flow fields with and without the roughness elements are obtained by solving the full Navier-Stokes equations in cylindrical coordinates using the fifth-order accurate weighted essentially non-oscillatory (WENO) scheme for spatial discretization and using the third-order total-variation-diminishing (TVD) Runge-Kutta scheme for temporal integration. Stability computations reveal that the azimuthal wavenumbers are in the range of m approx. 25-50 for the most amplified traveling disturbances and in the range of m approx. 40-70 for the stationary disturbances. The N-Factor computations predicted that transition would occur further forward in the middle of the cone compared to the transition fronts near the windward and the leeward planes. The simulations revealed that the crossflow vortices originating from the nose region propagate towards the leeward plane. No perturbations were observed in the lower part of the cone.

Balakumar, Ponnampalam↗

NASA NTRS2010

Analysis of Instabilities in Non-Axisymmetric Hypersonic Boundary Layers Over Cones

Hypersonic flows over circular cones constitute one of the most important generic configurations for fundamental aerodynamic and aerothermodynamic studies. In this paper, numerical computations are carried out for Mach 6 flows over a 7-degree half-angle cone with two different flow incidence angles and a compression cone with a large concave curvature. Instability wave and transition-related flow physics are investigated using a series of advanced stability methods ranging from conventional linear stability theory (LST) and a higher-fidelity linear and nonlinear parabolized stability equations (PSE), to the 2D eigenvalue analysis based on partial differential equations. Computed N factor distribution pertinent to various instability mechanisms over the cone surface provides initial assessments of possible transition fronts and a guide to corresponding disturbance characteristics such as frequency and azimuthal wave numbers. It is also shown that strong secondary instability that eventually leads to transition to turbulence can be simulated very efficiently using a combination of advanced stability methods described above.

Li, Fei↗

NASA NTRS2010

Stability of Hypersonic Boundary Layers on a Cone at an Angle of Attack

The stability and receptivity of a three-dimensional hypersonic boundary layer over a 7deg half-angle straight cone at an angle of attack of 6deg is numerically investigated at a freestream Mach number of 6.0 and a Reynolds number of 10.4x10(exp 6)/m. The generation and evolution of stationary crossflow vortices are also investigated by performing simulations with three-dimensional roughness elements located on the surface of the cone. The flow fields with and without the roughness elements are obtained by solving the full Navier- Stokes equations in cylindrical coordinates using a fifth-order accurate weighted essentially non-oscillatory (WENO) scheme for spatial discretization and a third-order total-variation-diminishing (TVD) Runge-Kutta scheme for temporal integration. Stability computations produced azimuthal wavenumbers in the range of m approx. 20-50 for the most amplified traveling disturbances and in the range of m approx.30-70 for the stationary disturbances. The frequency of the unstable second-mode ranges from 400 kHz to 900 kHz along the windward ray. The N-Factor computations predicted transition would occur more forward on the sides of the cone as compared to the transition fronts near the windward and the leeward rays. The simulations also show the crossflow vortices originating from the nose region propagate towards the leeward ray. No perturbations were observed toward the windward half of the cone.

Balakumar, P.↗

NASA NTRS2016

Measurements in a Transitioning Cone Boundary Layer at Freestream Mach 3.5

An experimental study was conducted in the Supersonic Low-Disturbance Tunnel to investigate naturally-occurring instabilities in a supersonic boundary layer on a 7 deg half- angle cone. All tests were conducted with a nominal freestream Mach number of M(sub infinity) = 3:5, total temperature of T(sub 0) = 299:8 K, and unit Reynolds numbers of Re(sub infinity) x 10(exp -6) = 9:89, 13.85, 21.77, and 25.73 m(exp -1). Instability measurements were acquired under noisy- ow and quiet- ow conditions. Measurements were made to document the freestream and the boundary-layer edge environment, to document the cone baseline flow, and to establish the stability characteristics of the transitioning flow. Pitot pressure and hot-wire boundary- layer measurements were obtained using a model-integrated traverse system. All hot- wire results were single-point measurements and were acquired with a sensor calibrated to mass ux. For the noisy-flow conditions, excellent agreement for the growth rates and mode shapes was achieved between the measured results and linear stability theory (LST). The corresponding N factor at transition from LST is N 3:9. The stability measurements for the quiet-flow conditions were limited to the aft end of the cone. The most unstable first-mode instabilities as predicted by LST were successfully measured, but this unstable first mode was not the dominant instability measured in the boundary layer. Instead, the dominant instabilities were found to be the less-amplified, low-frequency disturbances predicted by linear stability theory, and these instabilities grew according to linear theory. These low-frequency unstable disturbances were initiated by freestream acoustic disturbances through a receptivity process that is believed to occur near the branch I locations of the cone. Under quiet-flow conditions, the boundary layer remained laminar up to the last measurement station for the largest Re1, implying a transition N factor of N greater than 8:5.

King, Rudolph A.↗

NASA NTRS2021

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Boundary layer transition↗

NASA NTRS2022

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Hydrodynamic instability↗

NASA NTRS2022

Interaction of a Tunnel-like Acoustic Disturbance Field with a Blunt Cone Boundary Layer at Mach 8

The existing measurements of laminar-to-turbulent transition over circular cones in conventional (i.e., “noisy”) hypersonic wind tunnels have established that the transition location moves downstream when the nose radius is increased from zero. However, this initially downstream movement slows down and ultimately reverses beyond a critical value of the nose radius, and may be related to external forcing in the form of freestream disturbances and/or surface roughness. To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, hypersonic boundary-layer receptivity to broadband freestream acoustic disturbances from the nozzle wall of a digital conventional wind tunnel is investigated by both direct numerical simulations (DNS) and modal and nonmodal stability analysis. A Mach 8 flow over a 7 deg half-angle cone with a nose radius of 𝑅 𝑛 = 5.2mm and freestream Reynolds number of 12.2 × 10 6 m -1 is considered. The results show that the broadband tunnel noise in the free stream of a convectional hypersonic wind tunnel (i.e., outside of the nozzle-wall turbulent boundary layer) can be well represented by an acoustic model with an ansatz of slow acoustic waves. With successful calibration of the model parameters against the precursor tunnel DNS, such an acoustic ansatz can successfully reproduce both the frequency-wavenumber spectra and the temporal evolution of the broadband tunnel noise radiated from the nozzle wall. Additionally, the DNS of the Mach 8 blunt cone with tunnel-like acoustic input above the bow shock showed that the spectra of wall-pressure and heat-transfer fluctuations recovers the signature of the axisymmetric waves predicted by the nonmodal analysis. Furthermore, the azimuthal wavenumber and frequency spectrum of the temperature fluctuations as a function of the wall-normal distance show higher amplitudes for three-dimensional waves above the boundary-layer edge. The numerical schlieren contours show the inclined structures commonly observed in blunt cone experiments, demonstrating that they correspond to three-dimensional structures due to freestream disturbances in the presence of an entropy layer.

Boundary-layer transition↗

NASA NTRS2022

Interaction of a Tunnel-like Acoustic Disturbance Field with a Blunt Cone Boundary Layer at Mach 8

The existing measurements of laminar-to-turbulent transition over circular cones in conventional (i.e., “noisy”) hypersonic wind tunnels have established that the transition location moves downstream when the nose radius is increased from zero. However, this initially downstream movement slows down and ultimately reverses beyond a critical value of the nose radius, and may be related to external forcing in the form of freestream disturbances and/or surface roughness. To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, hypersonic boundary-layer receptivity to broadband freestream acoustic disturbances from the nozzle wall of a digital conventional wind tunnel is investigated by both direct numerical simulations (DNS) and modal and nonmodal stability analysis. A Mach 8 flow over a 7 deg half-angle cone with a nose radius of 𝑅 𝑛 = 5.2mm and freestream Reynolds number of 12.2 × 10 6 m -1 is considered. The results show that the broadband tunnel noise in the free stream of a convectional hypersonic wind tunnel (i.e., outside of the nozzle-wall turbulent boundary layer) can be well represented by an acoustic model with an ansatz of slow acoustic waves. With successful calibration of the model parameters against the precursor tunnel DNS, such an acoustic ansatz can successfully reproduce both the frequency-wavenumber spectra and the temporal evolution of the broadband tunnel noise radiated from the nozzle wall. Additionally, the DNS of the Mach 8 blunt cone with tunnel-like acoustic input above the bow shock showed that the spectra of wall-pressure and heat-transfer fluctuations recovers the signature of the axisymmetric waves predicted by the nonmodal analysis. Furthermore, the azimuthal wavenumber and frequency spectrum of the temperature fluctuations as a function of the wall-normal distance show higher amplitudes for three-dimensional waves above the boundary-layer edge. The numerical schlieren contours show the inclined structures commonly observed in blunt cone experiments, demonstrating that they correspond to three-dimensional structures due to freestream disturbances in the presence of an entropy layer.

Boundary layer transition↗

NASA NTRSDate not supplied

Hypersonic Boundary-Layer Transition over a Blunt Circular Cone in a Mach 8 Digital Wind Tunnel

To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, three-dimensional direct numerical simulations (DNS) were conducted to investigate the interaction of a tunnel-like acoustic disturbance field with a Mach 8 laminar boundary layer over a 7 deg half-angle blunt cone with a nose radius of 𝑅 𝑛 = 5.2 mm. The flow conditions and the axisymmetric cone geometry matched those measured in the Sandia Hypersonic Wind Tunnel at Mach 8 (Sandia HWT-8), and the incident freestream acoustic disturbances in the DNS were generated by acoustic radiation from the nozzle-wall turbulent boundary layer in the same tunnel. Consistent with the predictions of the nonmodal instability analysis, the study shows the emergence of a second spectral peak for moderately oblique waves between 150 kHz and 200 kHz in the aft part of the cone. The spectral energy of temperature and streamwise velocity fluctuations is initially concentrated within the entropy layer. These fluctiations are eventually “swallowed” by the boundary layer as the entropy-layer thickness 𝛿 𝑆 becomes similar to the boundary-layer thickness 𝛿h𝑡 at downstream locations. The numerical schlieren contours show the same inclined structures commonly observed in blunt cone experiments, and these structures are found to be three dimensional and advect with a constant speed approximately equal to the mean flow speed near the edge of the boundary layer.

Hypersonic Flow↗

NASA NTRSDate not supplied

Hypersonic Boundary-Layer Transition over a Blunt Circular Cone in a Mach 8 Digital Wind Tunnel

To understand the effects of freestream acoustic disturbances on transition reversal over a blunt body, three-dimensional direct numerical simulations (DNS) were conducted to investigate the interaction of a tunnel-like acoustic disturbance field with a Mach 8 laminar boundary layer over a 7 deg half-angle blunt cone with a nose radius of 𝑅 𝑛 = 5.2 mm. The flow conditions and the axisymmetric cone geometry matched those measured in the Sandia Hypersonic Wind Tunnel at Mach 8 (Sandia HWT-8), and the incident freestream acoustic disturbances in the DNS were generated by acoustic radiation from the nozzle-wall turbulent boundary layer in the same tunnel. Consistent with the predictions of the nonmodal instability analysis, the study shows the emergence of a second spectral peak for moderately oblique waves between 150 kHz and 200 kHz in the aft part of the cone. The spectral energy of temperature and streamwise velocity fluctuations is initially concentrated within the entropy layer. These fluctiations are eventually “swallowed” by the boundary layer as the entropy-layer thickness 𝛿 𝑆 becomes similar to the boundary-layer thickness 𝛿h𝑡 at downstream locations. The numerical schlieren contours show the same inclined structures commonly observed in blunt cone experiments, and these structures are found to be three dimensional and advect with a constant speed approximately equal to the mean flow speed near the edge of the boundary layer.

Hypersonic Flow↗

DOE OSTI2013

Micro-cone targets for producing high energy and low divergence particle beams

The present invention relates to micro-cone targets for producing high energy and low divergence particle beams. In one embodiment, the micro-cone target includes a substantially cone-shaped body including an outer surface, an inner surface, a generally flat and round, open-ended base, and a tip defining an apex. The cone-shaped body tapers along its length from the generally flat and round, open-ended base to the tip defining the apex. In addition, the outer surface and the inner surface connect the base to the tip, and the tip curves inwardly to define an outer surface that is concave, which is bounded by a rim formed at a juncture where the outer surface meets the tip.

47 OTHER INSTRUMENTATION↗

DOE OSTI2017

Commissioning of small field size radiosurgery cones in a 6-MV flattening filter-free beam

This study aimed to describe the commissioning of small field size radiosurgery cones in a 6-MV flattening filter free (FFF) beam and report our measured values. Four radiosurgery cones of diameters 5, 10, 12.5, and 15 mm supplied by Elekta Medical were commissioned in a 6-MV FFF beam from an Elekta Versa linear accelerator. The extraction of a reference signal for measuring small fields in scanning mode is challenging. A transmission chamber was attached to the lower part of the collimators and used for percentage depth dose (PDD) and profile measurements in scanning mode with a stereotactic diode. Tissue-maximum ratios (TMR) and output factors (OF) for all collimators were measured with a stereotactic diode (IBA). TMR and the OF for the largest collimator were also acquired on a polystyrene phantom with a microionization chamber of 0.016 cm{sup 3} volume (PTW Freiburg PinPoint 3D). Measured TMR with diode and PinPoint microionization chamber agreed very well with differences smaller than 1% for depths below 20 cm, except for the smaller collimator, for which differences were always smaller than 2%. Calculated TMR were significantly different (up to 7%) from measured TMR. OF measured with diode and chamber showed a difference of 3.5%. The use of a transmission chamber allowed the measurement of the small-field dosimetric properties with a simple setup. The commissioning of radiosurgery cones in FFF beams has been performed with essentially the same procedures and recommended detectors used with flattened beams. Good agreement was found between TMR measurements acquired with the IBA stereotactic diode and the PinPoint 3D microionization chamber. The transmission chamber overcomes the problem of extracting a reference signal and is of great help for small-field commissioning.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

DOE OSTI2024

Loss-cone stabilization in rotating mirrors: thresholds and thermodynamics

In the limit of sufficiently fast rotation, rotating mirror traps are known to be stable against the loss-cone modes associated with conventional (non-rotating) mirrors. This paper calculates how quickly a mirror configuration must rotate in order for several of these modes to be stabilized (in particular, the high-frequency convective loss cone, drift cyclotron loss cone and Dory–Guest–Harris modes). Commonalities in the stabilization conditions for these modes then motivate a modified formulation of the Gardner free energy and diffusively accessible free energy to be used for systems in which the important modes have wavevectors that are orthogonal or nearly orthogonal to the magnetic field, as well as a modification to include the effects of a loss region in phase space.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2017

Two-dimensional hexagonal M 3 C 2 (M = Zn, Cd and Hg) monolayers: novel quantum spin Hall insulators and Dirac cone materials

The intriguing Dirac cones in honeycomb graphene have motivated the search for novel two-dimensional (2D) Dirac materials. Based on density functional theory and the global particle-swarm optimization method, herein, we predict a new family of 2D materials in honeycomb transition-metal carbides M 3 C 2 (M = Zn, Cd and Hg) with intrinsic Dirac cones. The M 3 C 2 monolayer is a kinetically stable state with a linear geometry (C=M=C), which to date has not been observed in other transition-metal-based 2D materials. The intrinsic Dirac cones in the Zn 3 C 2 , Cd 3 C 2 and Hg 3 C 2 monolayers arise from p–d band hybridizations. Importantly, the Hg 3 C 2 monolayer is a room-temperature 2D topological insulator with a sizable energy gap of 44.3 meV. When an external strain is applied, additional phases with node-line semimetal states emerge in the M 3 C 2 monolayer. These novel stable transition-metal–carbon-framework materials hold great promise for 2D electronic device applications.

Material Science↗