Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BLADE TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Fatigue Test Design: Scenarios for Biaxial Fatigue Testing of a 60-Meter Wind Turbine Blade

Current practice in commercial certification of wind turbine blades is to perform separate flap and lead-lag fatigue tests. The National Renewable Energy Laboratory has been researching and evaluating biaxial fatigue testing techniques and demonstrating various options, typically on smaller-scale test articles at the National Wind Technology Center. This report evaluates some of these biaxial fatigue options in the context of application to a multimegawatt blade certification test program at the Wind Technology Testing Center in Charlestown, Massachusetts.

17 WIND ENERGY↗
NASA NTRS1972

Theory/test correlation of helicopter rotor blade element airloads in the blade stall regime

The effects of stall on a rotor blade element in a three-dimensional rotating environment was investigated. The model rotor test provided blade element airloads and local boundary layer flow characteristics at the three-quarter blade radius position for a wide range of rotor operating conditions. A description of the test program and the test results are presented.

Bobo, C. J.↗
NASA NTRS1979

Design, fabrication, test, and evaluation of a prototype 150-foot long composite wind turbine blade

The design, fabrication, testing, and evaluation of a prototype 150 foot long composite wind turbine blade is described. The design approach and material selection, compatible with low cost fabrication methods and objectives, are highlighted. The operating characteristics of the blade during rotating and nonrotating conditions are presented. The tensile, compression, and shear properties of the blade are reported. The blade fabrication, tooling, and quality assurance are discussed.

Gewehr, H. W.↗
NASA NTRS1990

Wingtip vortex turbine investigation for vortex energy recovery

A flight test investigation has been conducted to determine the performance of wingtip vortex turbines and their effect on aircraft performance. The turbines were designed to recover part of the large energy loss (induced drag) caused by the wingtip vortex. The turbine, driven by the vortex flow, reduces the strength of the vortex, resulting in an associated induced drag reduction. A four-blade turbine was mounted on each wingtip of a single-engine, T-tail, general aviation airplane. Two sets of turbine blades were tested, one with a 15' twist (washin) and one with no twist. Th power recovered by the turbine and the installed drag increment were measured. A trade-off between turbine power and induced drag reduction was found to be a function of turbine blade incidence angle. This test has demonstrated that the wingtip vortex turbine is an attractive alternate, as well as an emergency, power source.

Abeyounis, William K.↗
NASA NTRS1974

Fabrication and testing of prestressed composite rotor blade spar specimens

Prestressed composite spar specimens were fabricated and evaluated by crack propagation and ballistic penetration tests. The crack propagation tests on flawed specimens showed that the prestressed composite spar construction significantly suppresses crack growth. Damage from three high velocity 30 caliber projectile hits was confined to three small holes in the ballistic test specimen. No fragmentation or crack propagation was observed indicating good ballistic damage resistance. Rotor attachment approaches and improved structural performance configurations were identified. Design theory was verified by tests. The prestressed composite spar configuration consisted of a compressively prestressed high strength ARDEFORM 301 stainless steel liner overwrapped with pretensioned S-994 fiberglass.

Gleich, D.↗
NASA NTRS1990

Estimation of UH-60 blade aerodynamic loads and rotor impedance using generalized strain pattern/Kalman filter approach

The purpose of the study is to develop and verify a methodology capable of predicting the vibration levels and estimating the aerodynamic loads and rotor impedance of a rotorcraft blade. Simulated flight test data is generated, blade airloads and elastic hub motions are estimated from the simulated data through the use of the Kalman filter/smoother, simulation upgrading and parameter identification are performed, and the ability to identify rotor impedance from a simulation by isolating the rotor model and providing a prescribed motion for the hub as rotor excitation is demonstrated. It is pointed out that the statistical estimation procedure utilized in the proposed methodology minimizes the impact of sensor noise, truncation error, and instrumentation bias on the results.

Bruhis, Ofer↗
NASA NTRS1930

Tests of Five Metal Model Propellers with Various Pitch Distributions in a Free Wind Stream and in Combination with Model VE-7 Fuselage

This report describes the tests of five adjustable blade metal model propellers both in a free wind stream and in combination with a model fuselage with stub wings. The propellers are of the same form and cross section but have variations in radial distributions of pitch. By making a survey of the radial distribution of air velocity through the propeller plane of the model fuselage it was found that this velocity varies from zero at the hub center to approximately free stream velocity at the blade tip. The tests show that the efficiency of a propeller when operating in the presence of the airplane is, over the working range, generally less than when operating in a free wind stream, but that a propeller with a radial distribution of pitch of the same nature as the radial distribution of air velocity through the propeller plane suffers the smallest loss in efficiency.

Lesley, E P↗
NASA NTRS1987

Helicopter blade dynamic loads measured during performance testing of two scaled rotors

A test to determine the performance differences between the 27-percent-scale models of two rotors for the U.S. Army AH-64 helicopter was conducted in the Langley 14- by 22-Foot Subsonic Tunnel. One rotor, referred to as the baseline rotor, simulated the geometry and dynamic characteristics of the production baseline rotor, and the other rotor, referred to as the advanced rotor, was designed to have improved hover performance. During the performance test, the dynamic pitch-link forces and blade bending and torsion moments were also measured. Dynamic data from the forward flight investigation are reduced and presented. The advanced blade set was designed to have dynamic characteristics similar to those of the baseline rotor so that test conditions would not be limited by potential rotor instability and blade resonances, and so that the measured performance increments could be considered to be due purely to aerodynamic causes. Data show consistent trends with advance ratio for both blade sets with generally higher oscillatory loads occurring for the advanced blade set when compared with the baseline blade set.

Berry, John D.↗
NASA NTRS1982

Blade loss transient dynamic analysis of turbomachinery

This paper reports on work completed to develop an analytical method for predicting the transient non-linear response of a complete aircraft engine system due to the loss of a fan blade, and to validate the analysis by comparing the results against actual blade loss test data. The solution, which is based on the component element method, accounts for rotor-to-casing rubs, high damping and rapid deceleration rates associated with the blade loss event. A comparison of test results and predicted response show good agreement except for an initial overshoot spike not observed in test. The method is effective for analysis of large systems.

Stallone, M. J.↗
NASA NTRS1973

Engine investigation of an impingement-cooled turbine rotor blade

Experimentally determined heat transfer characteristics of an impingement-cooled turbine rotor blade are reported. The test results are compared with those obtained for three convection-cooled turbine blades tested in the same facility in addition to impingement correlations found in literature.

Gauntner, J. W.↗
NASA NTRS1991

Experimental investigation of helicopter vibration reduction using rotor blade aeroelastic tailoring

A wind tunnel investigation has been conducted to parametrically investigate the effect of blade nonstructural mass on helicopter fixed- and rotating-system vibratory loads. The data were obtained using Mach- and aeroelastically-scaled model rotor blades which allowed for the addition of concentrated nonstructural masses at multiple points along the blade radius. Testing was conducted for advance ratios ranging from 0.10 to 0.35 for ten blade mass configurations. Three thrust levels were obtained at representative full-scale shaft angles for each configuration. Results indicate that proper placement of blade nonstructural mass can provide reductions in fixed-system vibratory loads, but that correct mass placement and the loads reduction realized are dependent upon flight condition. The data base obtained with this investigation provides a comprehensive set of fixed-system shears and moments, blade moment, and blade flap and lag response. The data set is well suited for use in the correlation and development of advanced rotorcraft analyses.

Wilbur, Matthew L.↗
NASA NTRS1986

Development and testing of vortex generators for small horizontal axis wind turbines

Vortex generators (VGs) for a small (32 ft diameter) horizontal axis wind turbine, the Carter Model 25, have been developed and tested. Arrays of VGs in a counterrotating arrangement were tested on the inbound half-span, outboard half-span, and on the entire blade. VG pairs had their centerlines spaced at a distance of 15% of blade chord, with a spanwise width of 10% of blade chord. Each VG had a length/height ratio of 4, with a height of between 0.5% and 1.0% of the blade chord. Tests were made with roughness strips to determine whether VGs alleviated the sensitivity of some turbines to an accumulation of bugs and dirt on the leading edge. Field test data showed that VGs increased power output up to 20% at wind speeds above 10 m/s with only a small (less than 4%) performance penalty at lower speeds. The VGs on the outboard span of the blade were more effective than those on inner sections. For the case of full span coverage, the energy yearly output increased almost 6% at a site with a mean wind speed of 16 mph. The VGs did reduce the performance loss caused by leading edge roughness. An increase in blade pitch angle has an effect on the power curve similar to the addition of VGs. VGs alleviate the sensitivity of wind turbine rotors to leading edge roughness caused by bugs and drift.

Gyatt, G. W.↗
NASA NTRS1986

Euler calculations for rotor configurations in unsteady forward flight

A solution procedure is presented for the lifting transonic flow past modern rotor configurations in forward flight. In this procedure, the three-dimensional, unsteady Euler equations are solved in strong conservation form on a body-fitted moving coordinate system. A hybrid procedure of second order spatial accuracy and first order temporal accuracy is used to integrate the governing equations. In lifting flows, the effect of the elements of wake not captured by the computational procedure, and other aeroelastic effects are accounted for as local angle of attack corrections. Detailed comparisons with experimental data are presented for a 1/7 scale model of the Cobra OLS rotor, and for a three-bladed rotor tested in France. Some preliminary results are also presented for a three-dimensional blade vortex interaction problem.

Sankar, L. N.↗
NASA NTRS2011

Accelerating Climate and Weather Simulations through Hybrid Computing

Unconventional multi- and many-core processors (e.g. IBM (R) Cell B.E.(TM) and NVIDIA (R) GPU) have emerged as effective accelerators in trial climate and weather simulations. Yet these climate and weather models typically run on parallel computers with conventional processors (e.g. Intel, AMD, and IBM) using Message Passing Interface. To address challenges involved in efficiently and easily connecting accelerators to parallel computers, we investigated using IBM's Dynamic Application Virtualization (TM) (IBM DAV) software in a prototype hybrid computing system with representative climate and weather model components. The hybrid system comprises two Intel blades and two IBM QS22 Cell B.E. blades, connected with both InfiniBand(R) (IB) and 1-Gigabit Ethernet. The system significantly accelerates a solar radiation model component by offloading compute-intensive calculations to the Cell blades. Systematic tests show that IBM DAV can seamlessly offload compute-intensive calculations from Intel blades to Cell B.E. blades in a scalable, load-balanced manner. However, noticeable communication overhead was observed, mainly due to IP over the IB protocol. Full utilization of IB Sockets Direct Protocol and the lower latency production version of IBM DAV will reduce this overhead.

hybrid computing↗
NASA NTRS1974

The prediction of rotor rotational noise using measured fluctuating blade loads

In tests conducted at the NASA Langley Research Center Helicopter Rotor Test Facility, simultaneous measurements of the high-frequency fluctuating aerodynamic blade loads and far-field radiated noise were made on a full-scale, nontranslating rotor system. After their characteristics were determined, the measured blade loads were used in an existing theory to predict the far-field rotational noise. A comparison of the calculated and measured rotational noise is presented with specific attention given to the effect of blade loading coefficients, chordwise loading distributions, blade loading phases, and observer azimuthal position on the predictions.

Hosier, R. N.↗
NASA NTRS1980

Energy Efficient High-Pressure Turbine Leakage Technology Report

The leakage test program was one of such supporting technology programs structured to provide guidance to the Energy Efficient Engine High Pressure Turbine Component Design Effort. Leakage reduction techniques were identified and evaluated. Test models were used to simulate component leak paths and to evaluate leakage reduction techniques. These models simulated the blade/disk attachment, the vane inner platform attachment, and the vane outer platform attachment combined with the blade outer airseal. Disk blade attachment testing indicated that leakage in this area could be reduced to very low levels by paying careful attention to the tolerances along the contact surface between the blade vibration damper and the blade platform contact surface. The aim of feather seal testing was to achieve a goal for an effective leakage gap of one mil (.001 inch) per inch of feather seal length. Results indicated that effective gaps even below the goal level were achievable by (1) maintaining close tolerances between feather seals and their slots to minimize end gaps and limit seal rotation, (2) avoiding feather seal overlap, and (3) minimizing feather seal intersections. W seals were shown to be effective leakage control devices. Wire rope, in its present state of development, was shown not to be an effective sealing concept for application to the component design.

Gardner, W. B.↗