Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aerodynamic Heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Aerodynamic Heating and Boundary-Layer Transition on a 1/10-Power Nose Shape in Free Flight at Mach Numbers up to 6.7 and Free-Stream Reynolds Numbers up to 16 x 10(exp 6)

A modified 1/10-power nose shape has been tested in free flight at Mach numbers up to 6.7 and free - stream Reynolds numbers based on diameter up to 16 X 10(exp 6). Measured heating rates were presented and compared with calculated values. Agreement ranges from poor on the forward portion of the nose to good on the rearward portion. The local Reynolds numbers of transition based on calculated momentum thickness varied between 1, 600 and 350. Laminar flow was maintained at momentum thickness Reynolds numbers of about 1,000 until the free-stream Reynolds number based on a length of 1 foot reached about 27 X 10(exp 6). At slightly higher free-stream Reynolds numbers transition occurred at momentum thickness Reynolds numbers as low as 250.

Garland, Benjamine J↗
NASA NTRS1948

The effects of aerodynamic heating and heat transfer on the surface temperature of a body of revolution in steady supersonic flight

An approximate method for determining the convective cooling requirement in the laminar boundary-layer region of a body of revolution in high-speed flight was developed and applied to an example body. The cooling requirement for the example body was determined as a function of Mach number, altitude, size, and a surface-temperature parameter. The maximum value of Mach number considered was 3.0 and the altitudes considered were those within the lower constant-temperature region of the atmosphere (40,000 to 120,000 ft.). The extent of the laminar boundary layer was determined approximately at each condition as a function of the variables considered.

Scherrer, Richard↗
NASA NTRS1958

Effects of aerodynamic heating on X-15 temperatures

Paper describes examples which show how wind-tunnel model tests of the actual configuration of the aircraft aid in aerothermodynamic analyses and how these tests have made possible increased accuracy in structural temperature prediction. Also, from this and other research, development and design work on the X-15 has been done to accomplish a design consistent with the specified flight requirements. In this work, structural temperatures have been held within acceptable limits by providing sufficient heat sink material. Limited areas of the skin and leading edges are expected to attain temperatures greater than 1,200 degrees F. However, these areas have been carefully investigated for the effect of these higher temperatures on the structure and have been found to be satisfactory.

Kinsler, Martin R↗
NASA NTRS1961

Local Aerodynamic Heat Transfer and Boundary-Layer Transition on Roughened Sphere-Ellipsoid Bodies at Mach Number 3.0

A wind-tunnel investigation was made to determine heat-transfer distributions on three steel sphere-ellipsoid bodies with surface roughnesses of 5, 100, and 200 microinches. Tests were conducted in the Langley 9- by 6-foot thermal structures tunnel at a Mach number of 3.0, free-stream Reynolds numbers (based on model spherical diameter) of 4.25 x 10(exp 6) and 2.76 x l0(exp 6), and at a stagnation temperature of 650 F. Pressure distributions were obtained also on a fourth model. The results indicated that the combination of surface roughness and boundary-layer cooling tended to promote early transition and nullify the advantages attributable to the blunt shape of the model for reducing local temperatures. Good correlation between experimental heating rates and those calculated from laminar theory was achieved up to the start of boundary-layer transition. The correlation also was good with the values predicted by turbulent theory for surface stations downstream from the 45 deg. station.

Deveikis, William D.↗
NASA NTRS1962

Methods for Determining the Optimum Design of Structures Protected from Aerodynamic Heating and Application to Typical Boost-Glide or Reentry Flight Paths

General equations are developed for the design of efficient structures protected from thermal environments typical of those encountered in boost-glide or atmospheric-reentry conditions. The method is applied to insulated heat-sink stressed-skin structures and to internally cooled insulated structures. Plates loaded in compression are treated in detail. Under limited conditions of plate buckling, high loading, and short flight periods, and for aluminum structures only, the weights of both configurations are nearly equal. Load parameters are found and are similar to those derived in previous investigations for the restricted case of a constant equilibrium temperature at the outside surface of the insulation.

Harris, Robert S., Jr.↗
NASA NTRS1960

Tests of Aerodynamically Heated Multiweb Wing Structures in a Free Jet at Mach Number 2: Five Aluminum-Alloy Models of 20-Inch Chord with 0.064-Inch-Thick Skin, 0.025-Inch-Thick Webs, and Various Chordwise Stiffening at 2 deg Angle of Attack

An experimental study was made on five 2024-T3 aluminum-alloy multiweb wing structures (MW-2-(4), MW-4-(3), mw-16, MW-17, and MW-18), at a Mach number of 2 and an angle of attack of 2 deg under simulated supersonic flight conditions. These models, of 20-inch chord and semi-span and 5-percent-thick circular-arc airfoil section, were identical except for the type and amount of chordwise stiffening. One model with no chordwise ribs between root and tip bulkhead fluttered and failed dynamically partway through its test. Another model with no chordwise ribs (and a thinner tip bulkhead) experienced a static bending type of failure while undergoing flutter. The three remaining models with one, two, or three chordwise ribs survived their tests. The test results indicate that the chordwise shear rigidity imparted to the models by the addition of even one chordwise rib precludes flutter and subsequent failure under the imposed test conditions. This paper presents temperature and strain data obtained from the tests and discusses the behavior of the models.

Trussell, Donald H.↗
NASA NTRS1959

Aerodynamic Heating and Fatigue

A review of the physical condition's under which future airplanes will operate has been made and the necessity for considering fatigue in the design has been established. A survey of the literature shows what phases of elevated-temperature fatigue have been investigated. Other studies that would yield data of particular interest to the designer of aircraft structures are indicated.

Kroll, Wilhelmina D.↗
NASA NTRS2001

Research on Streamlines and Aerodynamic Heating for Unstructured Grids on High-Speed Vehicles

Engineering codes are needed which can calculate convective heating rates accurately and expeditiously on the surfaces of high-speed vehicles. One code which has proven to meet these needs is the Langley Approximate Three-Dimensional Convective Heating (LATCH) code. It uses the axisymmetric analogue in an integral boundary-layer method to calculate laminar and turbulent heating rates along inviscid surface streamlines. It requires the solution of the inviscid flow field to provide the surface properties needed to calculate the streamlines and streamline metrics. The LATCH code has been used with inviscid codes which calculated the flow field on structured grids, Several more recent inviscid codes calculate flow field properties on unstructured grids. The present research develops a method to calculate inviscid surface streamlines, the streamline metrics, and heating rates using the properties calculated from inviscid flow fields on unstructured grids. Mr. Chris Riley, prior to his departure from NASA LaRC, developed a preliminary code in the C language, called "UNLATCH", to accomplish these goals. No publication was made on his research. The present research extends and improves on the code developed by Riley. Particular attention is devoted to the stagnation region, and the method is intended for programming in the FORTRAN 90 language.

DeJarnette, Fred R.↗