Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Deformations of thick two-material cylinder under axially varying radial pressure

Stresses and deformations in thick, short, composite cylinder subjected to axially varying radial pressure are studied. Effect of slippage at the interface is examined. In the NASTRAN finite element model, multipoint constraint feature is utilized. Results are compared with theoretical analysis and SAP-IV computer code. Results from NASTRAN computer code are in good agreement with the analytical solutions. Results suggest a considerable influence of interfacial slippage on the axial bending stresses in the cylinder.

Patel, Y. A.↗

Effect of element density on the NASTRAN calculated mechanical and thermal stresses of a spar

A NASTRAN model of a spar was examined to determine the sensitivity of calculated axial thermal stresses and bending stresses to changes in element density of the model. The thermal stresses calculated with three different element densities resulted in drastically differing values. The position of the constraint also significantly affected the value of the calculated thermal stresses. Mechanical stresses calculated from an applied loading were insensitive to element density.

Jenkins, J. M.↗

Study on the residual stress relaxation in girth-welded steel pipes under bending load using diffraction methods

This research is dedicated to the experimental investigation of the residual stress relaxation in girth-welded pipes due to quasi-static bending loads. Ferritic-pearlitic steel pipes are welded with two passes, resulting in a characteristic residual stress state with high tensile residual stresses at the weld root. Also, four-point bending is applied to generate axial load stress causing changes in the residual stress state. These are determined both on the outer and inner surfaces of the pipes, as well as in the pipe wall, using X-ray and neutron diffraction. Focusing on the effect of tensile load stress, it is revealed that not only the tensile residual stresses are reduced due to exceeding the yield stress, but also the compressive residual stresses for equilibrium reasons. Furthermore, residual stress relaxation occurs both parallel and perpendicular to the applied load stress.

36 MATERIALS SCIENCE↗

Testing Ceramics for Diesel Engines

Adaptation of diesel engine allows prestressed ceramic materials evaluated under realistic pressure, temperature, and stress without introducing extraneous stress. Ceramic specimen part of prechamber of research engine. Specimen held in place by clamp, introduces required axial compressive stress. Specimen -- cylindrical shell -- surrounded by chamber vented or pressurized to introduce requisite radial stress in ceramic. Pressure chamber also serves as safety shield in case speimen disintegrates. Materials under consideration as cylinder liners for diesel engines.

Schneider, H. W.↗

Calculation of residual principal stresses in CVD boron on carbon filaments

A three-dimensional finite element model of the chemical vapor deposition of boron on a carbon substrate (B/C) is developed. The model includes an expansion of the boron after deposition due to atomic rearrangement and includes creep of the boron and carbon. Curves are presented showing the variation of the principal residual stresses and the filament elongation with the parameters defining deposition strain and creep. The calculated results are compared with experimental axial residual stress and elongation measurements made on B/C filaments. For good agreement between calculated and experimental results, the deposited boron must continue to expand after deposition, and the build up of residual stresses must be limited by significant boron and carbon creep rates.

Behrendt, D. R.↗

Stresses and deformations in composite tubes due to a circumferential temperature gradient

A linear elasticity solution for determining the response of composite tubes subjected to a circumferential temperature gradient is presented. Numerical examples are used to show that, in a single layer tube, fiber orientation strongly influences response. When the fibers are aligned axially, all stress components in the tube are small. When the fibers are aligned circumferentially, the hoop stress becomes large. This difference in behavior is due to the large difference between the radial and circumferential coefficients of thermal expansion when the fibers are oriented circumferentially. In multilayer tubes, stresses are quite high and just two constants characterize the overall bending and axial deformations of the tubes.

Hyer, M. W.↗

Biaxial Creep Behavior of Nb-Modified Zircaloys

Zr-Nb alloys are used as cladding materials to encapsulate radioactive fuel in nuclear reactors. They possess excellent corrosion resistance at high temperatures making it possible to achieve high fuel burn-up directly increasing the thermal efficiency of the reactor. While they are commonly used in recrystallized (Rx) form in boiling water reactors, there is a need to understand the effect of cold work and stress relief (CWSR) on biaxial creep characteristics of these materials due to their use in pressurized water reactors. In this study, the biaxial creep behaviors of as-received Zr-Nb alloys, HANA and Zirlo, have been investigated at 500 and 400 0C respectively using internally pressurized tubing superimposed with axial load under varied hoop (s?) to axial (sz) stress ratios of 0 to 2 while monitoring both the axial and hoop strains using an LVDT and a laser telemetric extensometer respectively. The crystallographic textures and creep loci of these as-received Zr-Nb alloys have been evaluated to correlate with the previous studies on recrystallized HANA4 and CWSR Zircaloy-4. The creep locus of HANA4 was found to be unaffected by initial state (CWSR or Rx) and showed close correspondence to planar isotropy while the creep locus of CWSR Zirlo exhibited more resistance to axial deformation than diametrical as per CWSR Zircaloy4 reported earlier. These differences are shown to arise from grain shape anisotropy of CWSR Zirlo and Zircaloy4. The simulated creep loci using crystallite orientation distribution functions (CODFs) in conjunction with prism slip models, showed excellent agreement with experimental results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Biaxial Creep Behavior of Nb-Modified Zircaloys

Zirconium-niobium (Zr-Nb) alloys are used as cladding materials to encapsulate radioactive fuel in nuclear reactors. They possess excellent corrosion resistance at high temperatures making it possible to achieve high fuel burnup, directly increasing the thermal efficiency of the reactor. While they are commonly used in recrystallized (Rx) form in boiling water reactors, there is a need to understand the effect of cold work and stress relief (CWSR) on the biaxial creep characteristics of these materials due to their use in pressurized water reactors. In this study, the biaxial creep behaviors of as-received Zr-Nb alloys, HANA and Zirlo®, have been investigated at 500°C and 400°C, respectively, using internally pressurized tubing superimposed with axial load under varied hoop σθ to axial σz stress ratios of 0 to 2 while monitoring both the axial and hoop strains using a linear variable displacement transformer and a laser telemetric extensometer, respectively. The crystallographic textures and creep loci of these as-received Zr-Nb alloys have been evaluated to correlate with the previous studies on recrystallized HANA4 and CWSR Zircaloy-4. The creep locus of HANA4 was found to be unaffected by initial state (CWSR or Rx) and showed close correspondence to planar isotropy while the creep locus of CWSR Zirlo exhibited more resistance to axial deformation than diametrical as per CWSR Zircaloy-4 reported earlier. These differences are shown to arise from grain-shape anisotropy of the CWSR Zirlo and Zircaloy-4. The simulated creep loci using crystallite-orientation distribution functions in conjunction with prism slip models showed excellent agreement with experimental results.

Tillman, Micah↗

Calculation of residual principal stresses in CVD boron on carbon filaments

A three-dimensional finite element model of the chemical vapor deposition (CVD) of boron on a carbon substrate (B/C) is developed. The model includes an expansion of the boron after deposition due to atomic rearrangement and includes creep of the boron and carbon. Curves are presented to show how the principal residual stresses and the filament elongation vary as the parameters defining deposition strain and creep are varied. The calculated results are compared with experimental axial residual stress and elongation measurements made on B/C filaments. This comparison requires that for good agreement between calculated and experimental results, the deposited boron must continue to expand after deposition, and that the build-up of residual stresses is limited by significant boron and carbon creep rates.

Behrendt, D. R.↗

Fatigue life prediction in bending from axial fatigue information

Bending fatigue in the low cyclic life range differs from axial fatigue due to the plastic flow which alters the linear stress-strain relation normally used to determine the nominal stresses. An approach is presented to take into account the plastic flow in calculating nominal bending stress (S sub bending) based on true surface stress. These functions are derived in closed form for rectangular and circular cross sections. The nominal bending stress and the axial fatigue stress are plotted as a function of life (N sub S) and these curves are shown for several materials of engineering interest.

Manson, S. S.↗

Buckling of unstiffened and ring stiffened cylindrical shells under axial compression.

Bifurcation stresses and initial postbuckling behavior of both unstiffened and outside ring stiffened circular cylindrical shells under axial compression are analyzed. The shells are assumed to have axisymmetric sinusoidal imperfections with arbitrary wavelengths and amplitudes. It is found that for large imperfection amplitudes and wavelengths both the unstiffened and the stiffened shells have extremely small bifurcation loads. The postbuckling analysis shows that for small imperfection amplitudes the bifurcations from the axisymmetric state are initially unstable and collapse is associated with the bifurcation points. However, for larger values of the imperfection amplitudes the bifurcations are stable. For unstiffened shells the transition from unstable to stable bifurcations can take place at very small values of the load. On the other hand, for stiffened shells it is found that bifurcations at load levels less than about 40% of the classical buckling load have stable initial postbuckling behavior.

Pedersen, P. T.↗

Axial Fatigue Tests at Zero Mean Stress of 24S-T and 75S-T Aluminum-alloy Strips with a Central Circular Hole

Axial fatigue tests at zero mean stress have been made on 0.032- and 0.064-inch 24S-T and 0.032-inch 75S-T sheet-metal specimens 1/4, 1/2, 1, and 2 inches wide without a hole and with central holes giving a range of hole diameter D to specimen width W from 0.01 to 0.95. No systematic difference was noted between the results for the 0.032-inch and the 0.064-inch specimens although the latter seemed the more consistent. In general the fatigue strength based on the minimum section dropped sharply as the ration D/W was increased from zero to about 0.25. The plain specimens showed quite a pronounced decrease in fatigue strength with increasing width. The holed specimens showed only slight and rather inconclusive evidence of this size effect. The fatigue stress-concentration factor was higher for 75S-T than for 24S-T alloy. Evidence was found that a very small hole would not cause any reduction in fatigue strength.

ALUMINUM ALLOYS-STRESSES↗

Critical stress of thin-walled cylinders in axial compression

Empirical design curves are presented for the critical stress of thin-walled cylinders loaded in axial compression. These curves are plotted in terms of nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75. The test data obtained from various sources follow the general trend of the theoretical curve for cylinders with clamped edges, agreeing closely with the theory in the case of short cylinders, but falling considerably below the theoretical results for long cylinders. The discrepancy in the case of long cylinders increases with increasing values of the ratio of radius to wall thickness. Plotting curves for different values of this ratio reduces the scatter in the test data and a certain degree of correlation with theory is achieved. Advantage is taken of this correlation to obtain estimated design curves for cylinders with simply supported edges, for which little experimental information is available. (author)

Batdorf, S B↗

Critical stress of thin-walled cylinders in axial compression

Empirical design curves are presented for the critical stress of thin-wall cylinders loaded in axial compression. These curves are plotted in terms of the nondimensional parameters of small-deflection theory and are compared with theoretical curves derived for the buckling of cylinders with simply supported and clamped edges. An empirical equation is given for the buckling of cylinders having a length-radius ratio greater than about 0.75.

Batdorf, S B↗

Transfer matrix approach to layered systems with axial symmetry

The stress and displacement distribution in a layered medium is found by means of transfer matrices. The surface loading exhibits axial symmetry, and each layer is of infinite extent in the horizontal direction, of constant depth, and is considered to be linearly elastic, homogeneous, and isotropic. The method developed has the built-in advantage of enforcing interface continuity conditions automatically. Its application to layered composites shows the flexibility with which it predicts the local as well as the global response of the medium.

Bahar, L. Y.↗

Methodology for Mechanical Property Testing of Fuel Cladding Using a Expanded Plug Wedge Test

An expanded plug method was developed earlier for determining the tensile properties of irradiated fuel cladding. This method tests fuel rod cladding ductility by utilizing an expandable plug to radially stretch a small ring of irradiated cladding material. The circumferential or hoop strain is determined from the measured diametrical expansion of the ring. A developed procedure is used to convert the load circumferential strain data from the ring tests into material pseudo-stress-strain curves, from which material properties of the cladding can be extracted. However, several deficiencies existed in this expanded-plug test that can impact the accuracy of test results, such as that the large axial compressive stress resulted from the expansion plug test can potentially induce the shear failure mode of the tested specimen. Moreover, highly nonuniform stress and strain distribution in the deformed clad gage section and significant compressive stresses, induced by bending deformation due to clad bulging effect, will further result in highly nonconservative estimates of the mechanical properties for both strength and ductility of the tested clad. To overcome the aforementioned deficiencies associated with the current expansion plug test, systematic studies have been conducted. By optimizing the specific geometry designs, selecting the appropriate material for the expansion plug, and adding new components into the testing system, a modified expansion plug testing protocol has been developed. A general procedure was also developed to determine the hoop stress in the tested ring specimen. A scaling factor, -factor, was used to convert the ring load Fring into hoop stress , and is written as _ = F_ring/tl , where t is the clad thickness and l is the clad length. The generated stress-strain curve agrees well with the associated tensile test data in both elastic and plastic deformation regions.

expansion plug test↗