SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Micro-tensile characterization of AGR-2 TRISO Particle Layers and Interlayer Regions, including experimental motivation, results, irradiated fuel kernel APT, Buffer, SiC omparison, conclusion, and future work.
Since graphene, a variety of 2D materials have been fabricated in a quest for a tantalizing combination of properties and desired physiochemical behavior. 2D materials that are piezoelectric, i.e., that allow for a facile conversion of electrical energy into mechanical and vice versa, offer applications for sensors, actuators, energy harvesting, stretchable and flexible electronics, and energy storage, among others. Unfortunately, materials must satisfy stringent symmetry requirements to be classified as piezoelectric. Here, 2D ultrathin single-crystal molybdenum oxide (MoO 2 ) flakes that exhibit unexpected piezoelectric-like response are fabricated, as MoO 2 is centrosymmetric and should not exhibit intrinsic piezoelectricity. However, it is demonstrated that the apparent piezoelectricity in 2D MoO 2 emerges from an electret-like behavior induced by the trapping and stabilization of charges around defects in the material. Arguably, the material represents the first 2D electret material and suggests a route to artificially engineer piezoelectricity in 2D crystals. Specifically, it is found that the maximum out-of-plane piezoresponse is 0.56 pm V -1 , which is as strong as that observed in conventional 2D piezoelectric materials. The charges are found to be highly stable at room temperature with a trapping energy barrier of ≈2 eV.
The International Standard ISO 18115-1 on terminology in surface chemical analysis has been revised with clarifications, modifications, and deletions to more than 70 terms and with the addition of more than 50 terms in response to trends, issues, and needs identified by the surface analysis community. This revision adds terminology and concepts associated with emerging methods such as atom probe tomography, near ambient pressure XPS, and hard X-ray photoelectron spectroscopy. It includes 25 new and revised terms to ensure that the description of resolution is consistent across all surface analysis methods. The 630 terms in the document cover words or phrases used in describing the samples, instruments, and concepts involved in surface chemical analysis. Here, the terms have been collated into subject specific sections to ensure that related terms can be found easily.
The discovery of ferromagnetism in atomically thin layers at room temperature widens the prospects of 2D materials for device applications. Recently, two independent experiments demonstrated magnetic ordering in two dissimilar 2D systems, CrI 3 and Cr 2 Ge 2 Te 6 , at low temperatures and in VSe 2 at room temperature, but observation of intrinsic room-temperature magnetism in 2D materials is still a challenge. Here a transition at room temperature that increases the magnetization in magnetite while thinning down the bulk material to a few atom-thick sheets is reported. DC magnetization measurements prove ferrimagnetic ordering with increased magnetization and density functional theory calculations ascribe their origin to the low dimensionality of the magnetite layers. Additionally, surface energy calculations for different cleavage planes in passivated magnetite crystal agree with the experimental observations of obtaining 2D sheets from non-van der Waals crystals.
Competing microstructural evolution mechanisms can exist simultaneously when duplex stainless steels are operating for several decades in a high temperature service environment. Such competition between different microstructural evolution pathways can be difficult to ascertain using simple model alloy systems necessitating detailed structural and compositional analysis of phase transformation mechanisms in complex alloys Thus, in this study duplex stainless steels with complex but well understood chemistries were used to investigate the relative importance of different heterogeneous nucleation sites – specifically spinodal decomposition and Cu clustering – on precipitation of Ni-Si-Mn particles during long term thermal aging. Precipitation of Ni-Si-Mn particles in duplex stainless steels and ferritic steels during thermal aging and irradiation is known to have profound effect on mechanical properties. Using duplex stainless steels with custom modified compositions along with atom probe tomography characterization and first-passage kinetic Monte Carlo (FPKMC) simulations it is revealed that while the interface between Cr and Fe formed during spinodal decomposition can be a pathway for diffusion of Ni, Si, Mn, and Cu, it is not a site that encourages precipitation of Ni-Si-Mn rich particles. Instead, the presence of a higher concentration of Cu in these steels leads to formation of small Cu clusters with high energy interfaces that act as nucleation sites for Ni-Si-Mn particles because of its strong interaction particularly with Ni increasing the chemical driving force for precipitation. These results will help inform predictive models for the use of duplex stainless steels and other precipitation-hardened alloys for extended operation at high temperatures.
Nano-oxide precipitates in a modern nanostructured ferritic alloy were investigated after extreme thermomechanical processing into a thin-walled tube geometry. It was found that the morphology of the precipitates changed from spherical to rod-shaped, with some increasing to aspect ratios of up to 9, despite the precipitate volume fraction (0.3%) and number density (> 10 23 m -3 ) of precipitates remaining unchanged. High-resolution electron microscopy showed that the precipitates likely remained coherent with the Fe-matrix, while atom probe tomography confirmed that the precipitate compositions remained unaffected by the transformation. The morphological change was attributed to the shearable nature of the (Y,Ti,O)-rich precipitates, indicating they should be considered as “soft” obstacles to dislocation motion. The elongation was most pronounced in larger (>5 nm) precipitates, which may be caused by preferential dissolution of the smallest (1–3 nm) precipitates followed by the competition between re-precipitation and solute diffusion to larger precipitates during recovery heat treatments.
Here, nucleation and growth of Ti3Al α( 2 ) ordered domains in alpha-Ti-Al-X alloys were characterised using a combination of transmission electron microscopy, atom probe tomography and small angle X-ray scattering. Model alloys based on Ti-7Al (wt.%) and containing O, V and Mo were aged at 550 °C for times up to 120d and the resulting precipitate dispersions were observed at intermediate points. Precipitates grew to around 30nm in size, with a volume fraction of 6-10% depending on tertiary solutes. Interstitial O was found to increase the equilibrium volume fraction of α 2 , while V and Mo showed relatively little influence. Addition of any of the solutes in this study, but most prominently Mo, was found to increase nucleation density and decrease precipitate size and possibly coarsening rate. Coarsening can be described by the Lifshitz-Slyozov-Wagner model, suggesting a matrix diffusion-controlled coarsening mechanism (rather than control by interfacial coherency). Solutionising temperature was found to affect nucleation number density with an activation energy of E f = 1.5 +/- 0.4 eV, supporting the hypothesis that vacancy concentration affects α 2 nucleation. The observation that all solutes increase nucleation number density is also consistent with a vacancy-controlled nucleation mechanism.
Bone-like materials comprise carbonated-hydroxyapatite nanocrystals (c-Ap) embedding a fibrillar collagen matrix. The mineral particles stiffen the nanocomposite by tight attachment to the protein fibrils creating a high strength and toughness material. The nanometer dimensions of c-Ap crystals make it very challenging to measure their mechanical properties. Mineral in bony tissues such as dentine contains 2~6 wt.% carbonate with possibly different elastic properties as compared with crystalline hydroxyapatite. Here we determine strain in biogenic apatite nanocrystals by directly measuring atomic deformation in pig dentine before and after removing carbonate. Transmission electron microscopy revealed the platy 3D morphology while atom probe tomography revealed carbon inside the calcium rich domains. High-energy X-ray diffraction in combination with in situ hydrostatic pressurization quantified reversible c-Ap deformations. Additionally, crystal strains differed between annealed and ashed (decarbonated) samples, following 1 or 10 h heating at 250 °C or 550 °C respectively. Measured bulk moduli (K) and a-/c-lattice deformation ratios (η) were used to generate synthetic K syn and ηsyn identifying the most likely elastic constants C 33 and C 13 for c-Ap. These were then used to calculate the nanoparticle elastic moduli. For ashed samples, we find an average E 11 =107 GPa and E 33 =128 GPa corresponding to ~5% and ~17% stiffening of the a-/c-axes of the nanocrystals as compared with the biogenic nanocrystals in annealed samples. Ashed samples exhibit ~10% lower Poisson's ratios as compared with the 0.25~0.36 range of carbonated apatite. Carbonate in c-Ap may therefore serve for tuning local deformability within bony tissues.
Existing regulatory pollutant monitoring networks rely on a small number of centrally located measurement sites that are purposefully sited away from major emission sources. While informative of general air quality trends regionally, these networks often do not fully capture the local variability of air pollution exposure within a community. Recent technological advancements have reduced the cost of sensors, allowing air quality monitoring campaigns with high spatial resolution. The 100×100 black carbon (BC) monitoring network deployed 100 low-cost BC sensors across the 15 km 2 West Oakland, CA community for 100 days in the summer of 2017, producing a nearly continuous site-specific time series of BC concentrations which we aggregated to one-hour averages. Leveraging this dataset, we employed a hierarchical spatio-temporal model to accurately predict local spatio-temporal concentration patterns throughout West Oakland, at locations without monitors (average cross-validated hourly temporal R 2 =0.60). Using our model, we identified spatially varying temporal pollution patterns associated with small-scale geographic features and proximity to local sources. In a sub-sampling analysis, here we demonstrated that fine scale predictions of nearly comparable accuracy can be obtained with our modeling approach by using ~30% of the 100×100 BC network supplemented by a shorter-term high-density campaign.
The oxidation resistance of Ni-based alloys is typically improved by additions of elements segregating to grain boundaries, contributing to reducing scale growth, and improving scale adherence. To develop a mechanistic understanding of doping, outward Al and inward O fluxes through the scale formed on β-NiAl with Ti, Y, and Ti+Y additions were characterized for oxidation at 1200°C and times up to 100h. Doped alloys exhibited varying reductions in oxidation rates and Al and O fluxes affecting scale grain morphologies. In conclusion, Ti+Y co-doping further reduced the outward Al and inward O transport compared to doping with Ti or Y alone.
Here, we compared the oxidation of Ti and Ti-2 at.% Nb at 800°C in Ar-20% O 2 and in sequential 16 O 2 - 18 O 2 atmospheres to clarify the role of niobium in the high-temperature oxidation of titanium. Niobium had no effect on the amount of oxygen dissolved in the metal or on oxygen diffusion in the metal. Instead, niobium enhanced oxidation resistance by segregating to TiO 2 grain boundaries, where it likely slowed outward Ti diffusion. These findings spotlight doping of TiO 2 grain boundaries as a strategy for improving the oxidation resistance of Ti alloys and, more generally, TiO 2 -forming alloys.
Here, we characterized the oxidation of pure Ti, Ti-0.8Si, and Ti-2Nb at 800 °C in N 2 -20% O 2 and in sequential isotopically labeled N 2 -20% O 2 atmospheres to clarify how nitrogen influences the high-temperature oxidation mechanisms of titanium alloys. The alloys always exhibited a nitride layer beneath a compact oxide scale with localized nitrogen concentrations in the underlying metal. Nitrogen is found to limit the oxygen concentrations in the metal. The synergy between alloying and nitrogen helps maintain compact oxide scales, preventing the formation of the lamellar scales observed during oxidation in nitrogen-free atmosphere and the oxidation of pure Ti regardless of the atmosphere.
Contouring inconsistencies are known but understudied in clinical radiation therapy trials. We applied auto-contouring to the Radiation Therapy Oncology Group (RTOG) 0617 dose escalation trial data. We hypothesized that the trial heart doses were higher than reported due to inconsistent and insufficient heart segmentation. We tested our hypothesis by comparing doses between deep-learning (DL) segmented hearts and trial hearts.
Although retained austenite is present in minor amounts in as-built additively manufactured-maraging steels, its evolution during ageing is key to controlling the final microstructure. This study investigates the relationship between austenite reversion and precipitation evolution during ageing, particularly whether these processes compete or cooperate. Using Scanning/Transmission Electron Microscopy, Atom Probe Tomography and Thermo-Calc® PRISMA simulations, the presence and evolution of retained austenite, Ni 3 Ti and Fe 7 Mo 6 intermetallic phases was characterised across different ageing conditions. Experimental results revealed the presence of non-enriched austenite in the as-built condition. Nevertheless, with increasing ageing temperature, Ni and Mo segregation became evident. High-Resolution Transmission Electron Microscopy revealed that Ni 3 Ti precipitation primarily occurred within the martensitic matrix, while Fe 7 Mo 6 nucleated preferentially at the austenite-martensite interface. PRISMA simulations indicated early and rapid precipitation in solute-enriched areas (i.e., intercellular regions), with Ni 3 Ti forming prior to Fe 7 Mo 6 . Both experimental and simulation results suggested Ni diffusion controls retained austenite growth, while Ti and Mo drive Ni 3 Ti and Fe 7 Mo 6 precipitation, respectively. The evidence reported in this work supports a both collaborative and independent phase transformation mechanism, where austenite reversion and precipitation co-evolve.
Alloy 800H is a high temperature and creep resistant alloy, and is considered as a candidate alloy for use in Generation IV nuclear reactor systems. To clarify the alloy's behavior under irradiation, samples were subjected to single ion irradiations up to 20 dpa at 440°C, a dual ion/He irradiation to 17 dpa at 460°C, and a neutron irradiation to 17 dpa at 385°C. The irradiated microstructures were characterized using atom probe tomography to complement previously published transmission electron microscopy studies. Additionally, after single ion irradiation, sparse fine Al and Ti clusters were observed after 1dpa, while high number densities of nanoscale Ni-Al-Ti clusters, Cr-Ti rich carbides, and Si-decorated dislocation loops developed after 10 and 20 dpa. The microstructure formed during single ion irradiation exhibited a strong depth dependence. No significant differences were observed between the single and dual ion irradiations. While Ni-Al-Ti clusters, Cr-Ti rich carbides, and Si-decorated dislocation loops were also observed after neutron irradiation, the neutron-irradiated microstructure differed from those found in the ion-irradiated samples.
In this study, high-Cu weld material harvested from an ex service reactor pressure vessel (RPV) steel from Unit 1 of the decommissioned Zion Nuclear Generating Station has been characterized using atom probe tomography. Samples taken from 4 different positions through the thicknesses of the pressure vessel wall from the water-side to the air-side were characterized, along with an unirradiated baseline material. In the baseline material, no precipitates were found and the Cu was observed to be fully in solid solution; however, scanning transmission electron microscopy combined with energy dispersive spectroscopy (STEM-EDS) revealed the presence of ϵ -Cu that form during processing of the material and results in the concomitant decrease of matrix Cu. Following irradiation, a high number density of nano-scale Cu-rich precipitates (CRPs) were observed, uniformly distributed throughout the matrix. The Cu content within the CRPs was found to be ~30-35 at.% regardless of location in the wall. No statistically significant variation in the compositions, mean radius, number density, or volume fraction as a function of location within the wall was observed. The measured matrix Cu level excluding CRPs contribution was found to be ~90 appm higher than the solubility limit suggesting that further nucleation and growth of the CRPs under continued operations would have occurred. These results clearly demonstrate that the neutron energy attenuation has no significant effect on the precipitation kinetics of CRPs regardless of location in the wall in high-Cu RPV steels under irradiation.
Thermal aging of ferrite in duplex stainless steels leads to a complex microstructural evolution that can give way to large deleterious changes in mechanical properties. The microstructural evolution mechanisms that happen concurrently are strongly linked to minor changes in composition. By characterizing duplex stainless steels with various compositions over a range of aging conditions, it was revealed that adding a modest amount of Mo to cast austenitic stainless steel (such as changing from grade CF3 to grade CF3M) not only increases the kinetics of spinodal decomposition and Ni-Si-Mn-rich G-phase precipitation, but it also forms a separate Mo-rich phase. At shorter equivalent aging times, Mo segregates from Fe and towards Cr accelerating spinodal decomposition. At longer aging times, Mo enriches in the Ni-Si-Mn clusters before phase separating into an adjoined Mo-rich cluster. We found that these phase changes and precipitation events result in a rather steep drop in fracture and impact toughness. These results will inform the design of similar alloys for use at high temperatures.