Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AMES LABORATORY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Electric Motor Thermal Management Research: Annual Progress Report

Past work in the area of active convective cooling provided data on the average convective heat transfer coefficients of circular orifice automatic transmission fluid (ATF) jets impinging on stationary targets intended to represent the wire bundle surface of the motor end-winding. Work during FY16 focused on the impact of alternative jet geometries that could lead to improved cooling over a larger surface of the motor winding. Results show that the planar jet heat transfer coefficients over a small (12.7-mm-diameter) target surface are not too much lower than for the circular orifice jet in which all of the ATF from the jet impinges on the target surface. The planar jet has the potential to achieve higher heat transfer over a larger area of the motor end winding. A new test apparatus was constructed to measure the spatial dependence of the heat transfer relative to the jet nozzle over a larger area representative of a motor end-winding. The tested planar flow geometry has the potential to provide more uniform cooling over the full end-winding surface versus the conventional jet configuration. The data will be used by motor designers to develop thermal management strategies to improve motor power density. Work on passive thermal design in collaboration with Oak Ridge National Laboratory to measure the thermal conductivity of wire bundle samples representative of end-winding and slot-winding materials was completed. Multiple measurement techniques were compared to determine which was most suitable for measuring composite wire bundle samples. NREL used a steady-state thermal resistance technique to measure the direction-dependent thermal conductivity. The work supported new interactions with industry to test new materials and reduce passive-stack thermal resistance in motors, leading to motors with increased power density. NREL collaborated with Ames Laboratory in the area of material characterization. The work focused on measuring the transverse rupture strength of new magnet materials developed at Ames. The impact of the improved transverse rupture strength is a mechanically stronger magnet that is easier for manufacturers to implement into motor designs. The thermal conductivity of the new magnet materials was also measured in comparison to two commercially available AlNiCo magnet materials. The impact of the thermal conductivity of the magnet material will need to be analyzed in the context of a motor application.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Creep-enhanced vortex pinning revealed through nonmonotonic relaxation of the Campbell length

Here, we study the effects of flux creep on the linear AC response of the vortex lattice in single crystals Ca 3 ⁢Ir 4 ⁢Sn 13 by measuring the Campbell penetration depth, 𝜆 C ⁡(𝑇,𝐻,𝑡) . Thermal fluctuations release vortices from shallow pinning sites, only for them to become re-trapped by deeper potential wells, causing an initial increase of the effective Labusch parameter, which is proportional to the pinning well curvature. This effect cannot be detected in conventional magnetic relaxation measurements but is revealed by our observation of a nonmonotonic time evolution of 𝜆 C ⁡(𝑇,𝐻,𝑡) , which directly probes the average curvature of the occupied pinning centers. The time evolution of 𝜆 C ⁡(𝑇,𝐻,𝑡) was measured at different temperatures in samples with different densities of pinning centers produced by electron irradiation. The curves can be collapsed together when plotted on a logarithmic time scale 𝑡 → 𝑇 ⁢ln ⁡(𝑡/𝑡 0 ) confirming that the time evolution is driven by flux creep. The 𝜆 C ⁡(𝑇,𝐻,𝑡) is hysteretic with a noticeable nonmonotonic relaxation in the presence of a vortex density gradient (after zero-field cooling), but is monotonic after field cooling, where the vortex density is uniform. This result quantitatively corroborates the novel picture of vortex creep based on the strong pinning theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Chemist: A Domain-Specific Language by Chemists for Chemists

Managing the complexity of quantum chemistry (QC) software is key to ensuring it remains accessible, maintainable, and reusable. Noticeably missing from the QC ecosystem are modules targeting bottleneck routines. Here we argue that this is likely due to the difficulty in defining interfaces for such modules. To that end, we introduce the open-source, publicly available Chemist library https://github.com/NWChemEx/Chemist. Chemist is a domain-specific language targeting the QC domain. Chemist has been developed focusing on performance and user-friendliness. Using Chemist, QC tasks are defined using familiar domain concepts such as molecules, wave functions, and operators. The domain objects are hierarchical to ensure a systematic encapsulation of information. Key features of Chemist include: extensibility, the ability to alias existing data, and the ability to succinctly define many common QC tasks. The usefulness of Chemist is demonstrated by discussing the interface of NWChemEx’s Fock build module and by showcasing a proof-of-concept self-consistent field algorithm containing uncertainty propagation.

Algorithms↗
DOE OSTI2025

Outflow Boundary Conditions for Turbine-Integrated Rotating Detonation Combustors

This study examines outflow boundary conditions (BCs) in computational fluid dynamics (CFD) simulations of a transition duct with and without guide vanes that converts supersonic flow exiting a rotating detonation combustor (RDC) to subsonic flow to drive a turbine. Since the flow exiting the transition duct has swirling shock waves with significant spatial and temporal variations in pressure, temperature, and Mach number, imposing proper BCs poses a challenge. To ensure all swirling shock waves exit the transition duct without creating non-physical reflected waves at its outlet, this study examined three outflow BCs: (1) the average pressure imposed at the duct’s outlet, (2) a nonreflecting BC (NRBC) with a specified average pressure imposed at the duct’s outlet, (3) the average pressure imposed at the outlet of an extension duct made up of a buffer layer and a sponge layer. This study is based on the three-dimensional, unsteady density-weighted-ensemble-averaged continuity, Navier–Stokes, and energy equations for a thermally perfect gas closed by the realizable k–ε model and “enhanced” wall functions. The results obtained show that imposing an average pressure at the transition duct’s outlet produces spurious waves that degrade the physical meaningfulness of the solution. When the NRBC was applied, swirling shock waves exited the duct’s outlet without creating spurious waves. However, its usage requires the gas to be thermally, as well as calorically, perfect, which this study shows could be a concern. By imposing the average pressure at the outlet of an extension duct, the gas does not need to be calorically perfect. The results obtained show the effects of the sponge layer’s length and coarsening ratio on damping nonuniformities in non-physical reflected waves to ensure the flow exiting the transition duct’s outlet can do so as if there are no boundaries present and has the desired average pressure—even though the BC is applied at the extension duct’s outlet.

gas turbines↗
DOE OSTI2025

Suppressing Ordering in Equiatomic Fe-Co via Laser Powder Bed Fusion

Neutron and electron diffraction was employed to evaluate the effectiveness of thermal management strategies in suppressing the formation of the equilibrium-ordered B2 (CsCl) phase in equiatomic binary Fe-Co specimens fabricated by laser powder bed fusion additive manufacturing. Specimens with a tensile dogbone geometry were fabricated using various combinations of process parameters (laser power and raster speed) and thermal management strategies (no support struts, struts only in the top gauge section, and struts throughout the gauge section). Diffraction results demonstrate that the rapid solidification during PBF-L effectively minimized B2 formation, with laser power and effective scan velocity having no significant impact on the degree of ordering. Furthermore, the inclusion of support struts in the top grip region had no perceivable impact on ordering, whereas specimens with support struts in the gauge region exhibited no detectable ordering. Results are discussed in the context of thermal finite element analysis predictions.

Laser Material Processing↗
DOE OSTI2026

The effect of varying powder feedstock chemistry and printing atmosphere on the microstructure of additively manufactured nickel-based ODS alloys: Role on stabilization of cellular structures vs. oxide dispersion formation

Nickel-based alloys have a wide variety of structural applications due to their high corrosion resistance and mechanical strength which depend on solid solution strengthening, or the formation of oxides and/or intermetallic precipitation for their properties. In this study, the microstructure of six Ni–Cr–Y–Ti–Al powder batches designed for the production of oxide dispersion strengthened nickel were compared. These batches varied in chemistry and atomization technique used which included Gas Atomization Reactive Synthesis (GARS). The batches of powder were then consolidated via Additive Manufacturing (AM) Powder Bed Fusion using Laser Beam (PBF-LB) and characterized via transmission electron microscopy to elucidate the influence of powder feedstock (i.e. synthesis methodology and chemistry) on the PBF-LB microstructure. The study investigates (i) how the amount of yttrium and titanium additions in the powder feedstock and the addition of oxygen during the processing (through GARS) affect the microstructure of the powder itself and the AM printed microstructure, and (ii) how the control of oxygen addition in the printing atmosphere during the PBF-LB printing process itself is another important parameter for achieving the formation of the wanted oxide dispersion versus the stabilization of the cellular structure (often observed in AM processed alloys). Microstructural characterization of both powder particles and additively manufactured nickel alloys in this study provide important insights into the movement of yttrium within the material upon solidification, particularly along cell boundaries, and how yttrium behaves depending on alloy chemistry. When a threshold of yttrium content is reached within the system, yttrium consistently reacts to form an intermetallic along cell boundaries instead of forming oxide nanoparticles.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Engineered Zircaloy Cladding Modifications for Improved Accident Tolerance of LWR Nuclear Fuel

The DOE NEUP sponsored IRP on accident tolerant fuel (ATF) entitled Engineered Zircaloy Cladding Modifications for Improved Accident Tolerance of LWR Nuclear Fuel involved three academic institutions, Idaho National Laboratory (INL), and ATI Materials (ATI). Detailed descriptions of the work at the University of Illinois (UIUC, prime), the University of Florida (UF), the University of Michigan (UMich), and INL are included in this document as separate sections. This summary provides a synopsis of the work performed across the IRP team. Two ATF solution pathways were initially proposed, coatings on monolithic Zr-based LWR cladding material and selfhealing modifications of Zr-based alloys. The coating pathway was extensively investigated, both experimentally and in computations. Experimental activities related to ATF coatings were centered at UIUC, UF, and UMich and involved coating development and testing, and ion irradiation. Neutronic and thermal hydraulic aspects of ATF coatings were the focus of computational work at UIUC and UMich, while materials science aspects were the focus of computational work at UF and INL. ATI provided monolithic Zircaloy 2 and 4 material and a binary Zr-Y alloy material. The selfhealing pathway was investigated with advanced computations only. Beryllium was identified as a valid self-healing additive early in this work. However, all attempts to fabricate a Zr-Be alloy failed. Several avenues of fabrication were explored. ATI ultimately declined our fabrication request over health concerns associated with Be (we note that Be was not part of the original work scope and the ATI SOW). Likewise, Ames Laboratory declined our fabrication request, citing known litigation dating to the 1980s and 1990s involving the U.S. Federal government and U.S. National Laboratory employees involving the use of Be. Materion (formerly, Brush Wellman) also declined our fabrication request, citing the difficulty in working with a highly reactive Zr and Be. International fabrication options were explored in Europe and Asia, but this proved to be impractical, if not impossible. Consequently, experimental investigation of the Zr-Be binary system was dropped and exploration binary Zr-Y binary system was initiated. The motivation behind the Zr-Y system is the known thermodynamic stability of yttria over zirconia.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Observable measurement-induced transitions

One of the main postulates of quantum mechanics is that measurements destroy quantum coherence (wave function collapse). Recently it was discovered that in a many-body system dilute local measurements still preserve some coherence across the entire system. As the measurement density is increased, a phase transition occurs that is characterized by the disentanglement of different parts of the system. Unfortunately, this transition is impossible to observe experimentally for macroscopic systems because it requires an exponentially costly full tomography of the many-body wave function or a comparison with the simulation on an oracle classical computer. In this work we report the discovery of another measurement-induced phase transition that can be observed experimentally if quantum dynamics can be reversed. On one side of this phase transition the quantum information encoded in some part of the Hilbert space is fully recovered after the time inversion. On the other side, all quantum information is corrupted. This transition also manifests itself as the change in the behavior of the probability to observe the same measurement outcome in the process that consists of identical blocks repeated many times. In each block the unitary evolution is followed by the measurement. On one side of the transition the probability decreases exponentially with the number of repetitions, on the other it tends to a constant as the number of repetitions is increased. We confirm the existence of the proposed phase transition through numerical simulations of realistic quantum circuits and analytical calculations using an effective random-matrix theory model.

Measurement-induced phase transitions↗
DOE OSTI2026

Interface-engineered (CrMnTiZnCo) 3 O 4 @polypyrrole nano-hybrids for superior lithium storage

High-entropy oxides (HEO) have emerged as promising anode materials for lithium-ion batteries (LIBs) due to their high theoretical specific capacity. However, their practical application is hindered by several challenges, including significant volume expansion, electrode pulverization, and substantial irreversible capacity loss during initial cycles. To address these limitations, this study designed a novel core-shell composite material, denoted as HEO@PPy, which consists of a (CrMnTiZnCo) 3 O 4 -based HEO core and a polypyrrole (PPy) shell. This composite demonstrates remarkable electrochemical performance: it maintains a specific capacity of 1090.1 mAh/g after 100 cycles at 100 mA/g and retains 521.8 mAh/g after 1000 cycles at 1 A/g, highlighting its superior cycling stability. Furthermore, it exhibits excellent rate capability, delivering a capacity of 372.1 mAh/g even at a high current density of 5 A/g. These findings confirm that the strategic compositional and structural design of HEOs, combined with hybridization with conductive polymers like PPy, provides a viable pathway for developing advanced anode materials for next-generation, high-performance lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Microstructure refinement of hot deformed Dy-free NdFeB magnets through a novel cold sintering approach by pressure-assisted spark plasma sintering

Anisotropic fine-grained Dy-free NdFeB high-performance magnets were produced using a novel cold sintering approach by pressure-assisted spark plasma sintering (SPS). The NdFeB nanocrystalline ribbon powders were subjected to cold sintering below 450 °C using pressure-assisted SPS, followed by hot deformation at 710 °C and 810 °C via SPS. Results indicate that cold sintering below 450 °C effectively restricts grain growth in the NdFeB magnets, yielding sub-100 nm scale grains across both fine-grained regions and most coarse-grained regions. The refined grain structure achieved through cold sintering allows for a lower hot deformation temperature as compared with the magnet by conventional sintering, as finer grains allow easier deformation and grain sliding/rotation. This process produces a highly fine-grained and anisotropic microstructure to achieve high magnetic performance (i.e., high intrinsic coercivity, remanence, and maximum energy product) in the magnets. The cold sintering (at 350 °C) and lower hot deformation temperatures required (e.g., 710 °C) help control grain coarsening and limit grain size that is commensurate with the size of a single magnetic domain of the Nd 2 Fe 14 B magnetic matrix phase, resulting in high intrinsic coercivity (H ci =11.4 kOe). Furthermore, the reduced hot deformation temperature mitigates the formation of coarse grain bands, leading to improved magnetic properties, specifically an increased remanence (B r = 14.3 kGs) and a high maximum energy product ((BH) max = 48 MGOe). In conclusion, cold sintered hot deformed NdFeB magnet also shows good thermal stability with reversible temperature coefficient α(B r )= -0.097 %/K and α(H ci )= -0.616 %/K at elevated temperatures up to 400 K.

Cold Sintering↗
DOE OSTI2025

Significant acceleration of solid-state NMR simulations via three-angle powder averaging

The anisotropic frequency shifts imparted onto the NMR resonance frequency depend on the spherical angular coordinates that describe the orientations of the NMR interaction tensors with respect to the applied magnetic field direction. Experiments performed using magic-angle spinning, however, gain a dependence on a third angle: the rotor phase γ. Traditionally, a carousel average is performed to integrate over γ, which leads to a slow convergence of intensities without contributing to the underlying powder patterns. Herein, we show an order of magnitude acceleration in computation time may be obtained by including the γ-averaging into the main powder average to eliminate redundant calculation of resonance frequencies.

magic-angle spinning↗
DOE OSTI2026

Itinerant Magnetism in Hydride-Synthesized CaCo 12 B 6

A new compound in the underexplored Ca–Co–B phase space has been discovered, validating high-throughput computations from the Open Quantum Materials Database, which predicted thermodynamic stability for CaCo 12 B 6 in the SrNi 12 B 6 structure type. The synthetic effects of different boron precursors and the advantages of using CaH 2 instead of Ca metal were demonstrated by the short synthesis duration and high purity of CaCo 12 B 6 , in contrast with traditional synthesis routes. Powder X-ray diffraction (PXRD) confirmed that CaCo 12 B 6 shares the SrNi 12 B 6 structure ( R $\bar{3}$m (#166), a = 9.469(4) Å, c = 7.468(2) Å, Z = 3) and is water- and air-stable. High-temperature in situ PXRD indicates that CaCo 12 B 6 is stable below 1050 K under vacuum in a silica capillary. CaCo 12 B 6 decomposes between 693 and 773 K during spark-plasma sintering. Density functional theory calculations indicate that CaCo 12 B 6 is metallic with a ferromagnetic ground state. X-ray absorption near-edge spectroscopy and Bader charge analysis indicate that Co atoms in CaCo 12 B 6 lack ionic character. Magnetometry reveals room-temperature paramagnetism with μ eff = 1.7(1)μ B per Co atom and a Weiss constant of +190(10)K. Ferromagnetic ordering occurs below 172(1)K, resulting in a saturation moment of 0.46 μ B per Co atom. Our findings demonstrate that the hydride route is a viable strategy for discovery of new ternary alkaline-earth-transition metal borides analogous to rare-earth-containing counterparts.

diffraction↗
DOE OSTI2025

Perspectives on the Dynamic Nuclear Polarization Mechanisms of Monoradicals: Overhauser Effect or Thermal Mixing?

This mini-review summarizes the evolving debate regarding the origins of the absorptive features seen in the dynamic nuclear polarization (DNP) spectra of certain monoradicals when they are irradiated at their electron Larmor frequency. This feature has drawn attention due to its reverse scaling with respect to the magnetic field strength and potential for high-field DNP. Two competing hypotheses have been introduced to explain the DNP feature based on (1) the Overhauser effect and low-temperature molecular dynamics and (2) radical clustering and a thermal mixing mechanism. Since the original discovery, a large number of experimental observations have been made in attempts to understand and ultimately leverage the mechanism. We summarize these observations and provide critical assessments of how the competing hypotheses approach them.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Designing Thermomechanically Stable Nanocrystalline Alloys for Low Friction and Wear: A Perspective

In this Perspective, we discuss recent work and future trends on the usage of thermomechanically stable and selflubricating nanocrystalline (NC) alloys for low friction and wear applications. The theoretical underpinnings and mechanistic framework for attaining and maintaining low friction and wear in metal contacts are presented. Initial work on stress, time, and temperature-dependent changes in friction and wear in NC alloys validates the models, demonstrating lower friction from decreased interfacial strength, contact pressure, sliding speed, and temperature and increased roughness and material hardness. Subsequent work reveals that NC Pt−Au, metal nitrides, complex-concentrated, and high-entropy alloys come with additional stabilization factors such as low-friction carbon tribofilms and oxide/amorphous−crystalline layers but are still susceptible to destabilization factors including irradiation and adverse environmental conditions.

alloys↗
DOE OSTI2025

Stable single-site organonickel catalyst preferentially hydrogenolyses branched polyolefin C–C bonds

Current methods of processing accumulated polyolefin waste typically require harsh conditions, precious metals or high metal loadings to achieve appreciable activities. Here, in this work, we examined supported, single-site organonickel catalysts for polyolefin upcycling. Chemisorption of Ni(COD) 2 (COD, 1,5-cyclooctadiene) onto Brønsted acidic sulfated alumina (AlS) yields a highly electrophilic Ni(I) precatalyst, AlS/Ni(COD) 2 , which is converted under H 2 to the active AlS/Ni II H catalyst. This single-site system exhibits unique hydrogenolysis selectivity that favours cleaving branched polyolefin C–C linkages, enabling the hydrogenolytic separation of polyethylene and isotactic polypropylene (iPP) mixtures. Moreover, AlS/Ni II H remains highly selective and active for hydrogenolysis of iPP admixed with polyvinyl chloride, and the spent catalyst can be repeatedly regenerated by AlEt3 treatment. Experimental mechanistic analysis and density functional theory modelling reveal a turnover-limiting C–C scission pathway featuring β-alkyl transfer and strong olefin binding. These results highlight the potential of nickel-based systems for the selective upcycling of complex plastic waste streams.

green chemistry↗
DOE OSTI2025

Come for predictions, stay for complexity: synthesis and experimental probing of ionic conductivity in Li 9 B 19 S 33

Lithium thioborates, despite their potential cost-effectiveness and low density, have received considerably less attention as solid electrolytes compared to their thiophosphate counterparts. A primary obstacle to their widespread investigation has been the inherent challenge in synthesizing single-phase materials. Computational studies have predicted several lithium thioborate phases exhibiting high ionic conductivity, with Li 9 B 19 S 33 notably predicted to reach 80 mS cm −1 . However, experimental validation of these theoretical predictions remains absent. This work addresses this gap by detailing a successful synthesis of the previously elusive Li 9 B 19 S 33 phase, facilitated by in situ temperature dependent powder X-ray diffraction. Our findings reveal the peritectic nature of phase formation, necessitating an excess of boron sulfide in the reaction mixture. We further present a comprehensive structural characterization of Li 9 B 19 S 33 utilizing spectroscopic techniques like NMR, FT-IR, and diffuse reflectance and report on its ionic conductivity. Solid-state 6 Li NMR line narrowing experiments revealed an ion mobility activation energy of 0.26 eV whereas activation energies derived from impedance spectroscopy measurements were significantly higher, resulting in lower than theoretically predicted ionic conductivity.

Oppong, Richeal A. [Iowa State Univ., Ames, IA (Un↗
DOE OSTI2025

High-throughput studies of novel magnetic materials in borides

Borides are a versatile material family with various properties for valuable applications. Conventional magnetism, such as ferromagnetism and antiferromagnetism in borides, have been extensively studied. However, research on unconventional magnetism in borides where quantum effects are dominant is scarce. Here, we implement a high-throughput workflow combining first-principles calculations, materials prediction, and magnetic properties calculations to discover novel magnetism and magnetic materials in borides. Successfully applying the workflow, we report three families of novel magnetic borides, including two families of borides exhibiting quantum magnetism. One is a family of dimerized quantum magnets among YCrB 4 -type borides, which provides a rare platform for studying the spin-gap quantum critical point. The other is a family of altermagnets among FeMo2B 2 -type borides, extending the magnetic orderings exhibited by borides beyond conventional ferromagnetism and antiferromagnetism. We also predict a family of magnetic laminate transition metal borides, known as the MAB phases, in the AlFe 2 B 2 -type family, which provide pure-phase or alloying candidates for studying magnetocaloric materials and the associated magnetic transitions. The workflow is expected to be used in further studies of novel magnetism and magnetic materials.

36 MATERIALS SCIENCE↗