Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ALLOY SYSTEMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Magnetic properties of Fe-Cu alloys prepared by pulsed electrodeposition

Fe{sub x}Cu{sub 100-x} metastable alloys were prepared by pulsed electrodeposition for 5<x<85. The Fe-rich alloys crystallize in the bcc structure of alpha-Fe and the Fe-poor ones in the fcc structure of Cu. The magnetic properties of the ferromagnetic Fe-rich alloys (x>50) are reminiscent of those observed in Fe-Cu alloys prepared by other methods. The Curie temperature decreases regularly with decreasing x. In the Fe-poor alloys (x<=30), the observed properties indicate that Fe-rich clusters form within a Cu-rich matrix. In the x=10 alloy, the Fe clusters are found to be superparamagnetic at room temperature, but a superferromagnetic order develops below a critical temperature of about 120 K. It is suggested that the intercluster coupling is mediated by Ruderman-Kittel-Kasuya-Yosida interactions which are predominantly positive due to the very short intercluster distances.

36 MATERIALS SCIENCE↗

A Study of Al-Zn-Sn Alloy Sacrificial Anode Cathodic Protection Requirements for Structure Used In Seawater

The corrosion of aluminium (Al) alloys in seawater was investigated using potentiodynamic technique, complemented by Scanning Electron Microscopy (SEM), EDAX and XRD. SEM was used out to characterize the corroded surface and to observe the extent of corrosion attack on the Al alloys tested in seawater. EDAX analysis was used to identify elements present on the specimen surface. Where else XRD was to identify phase appearance. The results indicate that zinc (Zn), stanum (Sn) and copper (Cu) as alloying elements enhance corrosion behaviour of the aluminium in seawater by shifting the potential to a more negative value. In the presence of those elements, the Al alloys becomes more active, having potential of more than -1.0 V{sub SCE} and showed active corrosion behaviour.

36 MATERIALS SCIENCE↗

Surface Enhanced Raman Spectroscopy of Pyridine on CdSe/ZnBeSe Quantum Dots Grown by MBE

Using Surface Enhanced Raman Spectroscopy (SERS), we observed Raman enhancements (104-105) for pyridine molecules adsorbed on a II-VI semiconductor CdSe/ZnBeSe sample of uncapped self-assembled quantum dots produced by molecular beam epitaxy. When a monolayer of pyridine is adsorbed on these structures, excitation at 488 nm produces intense Raman spectra a very large enhancement of the a1, b1 and b2 modes. This indicates the presence of charge-transfer as a contributor to the enhacement.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural, thermal, optical, and photoacoustic study of nanocrystalline Bi{sub 2}Te{sub 3} produced by mechanical alloying

Nanocrystalline Bi{sub 2}Te{sub 3} was produced by mechanical alloying and its properties were investigated by differential scanning calorimetry (DSC) x-ray diffraction (XRD), Raman spectroscopy (RS), and photoacoustic spectroscopy (PAS). Combining the XRD and RS results, the volume fraction of the interfacial component in as-milled and annealed samples was estimated. The PAS results suggest that the contribution of the interfacial component to the thermal diffusivity of nanostructured Bi{sub 2}Te{sub 3} is very significant.

36 MATERIALS SCIENCE↗

Significant elastic anisotropy in Ti{sub 1-x}Al{sub x}N alloys

Strong compositional-dependent elastic properties have been observed theoretically and experimentally in Ti{sub 1-x}Al{sub x}N alloys. The elastic constant, C{sub 11}, changes by more than 50% depending on the Al-content. Increasing the Al-content weakens the average bond strength in the local octahedral arrangements resulting in a more compliant material. On the other hand, it enhances the directional (covalent) nature of the nearest neighbor bonds that results in greater elastic anisotropy and higher sound velocities. The strong dependence of the elastic properties on the Al-content offers new insight into the detailed understanding of the spinodal decomposition and age hardening in Ti{sub 1-x}Al{sub x}N alloys.

36 MATERIALS SCIENCE↗

Electrochemical characterization of a low modulus Ti-35.5Nb-7.3Zr-5.7Ta alloy in a simulated body fluid using EIS for biomedical applications

Electrochemical characterization of the low modulus Ti-35.5Nb-7.3Zr-5.7Ta beta alloy (TNZT) has been performed in phosphate buffer saline solution at 37 deg. C using the non destructive electrochemical impedance spectroscopy technique. Measurements were performed at various immersion intervals at the open circuit potential (OCP), which was also monitored with time. Results obtained for TNZT alloy have been compared with those for the commercially used Ti-6Al-4V mixed alloy (Ti64) and the commercially pure titanium (Ti2) alpha alloy. Potentiodynamic polarization was performed to supplement the data obtained from EIS analysis. The TNZT alloy exhibits a two time constant impedance response, whereas the Ti64 and Ti2 alloys display a one time constant behavior. Human fetal osteoblast cells show a better adhesion and a higher cell count for the TNZT alloy compared to the other two alloys. The present investigation is an effort to understand the correlation between the electrochemical, morphological and cellular characteristics of titanium alloys to qualify them for implant applications.

36 MATERIALS SCIENCE↗

Temperature Dependent Electrical Transport Properties of Ni-Cr and Co-Cr Binary Alloys

The temperature dependent electrical transport properties viz. electrical resistivity and thermal conductivity of Ni{sub 10}Cr{sub 90} and Co{sub 20}Cr{sub 80} alloys are computed at various temperatures. The electrical resistivity has been calculated according to Faber-Ziman model combined with Ashcroft-Langreth partial structure factors. In the present work, to include the ion-electron interaction, we have used a well tested local model potential. For exchange-correlation effects, five different forms of local field correction functions due to Hartree (H), Taylor (T), Ichimaru and Utsumi (IU), Farid et al (F) and Sarkar et al (S) are used. The present results due to S function are in good agreement with the experimental data as compared to results obtained using other four functions. The S functions satisfy compressibility sum rule in long wave length limit more accurately as compared to T, IU and F functions, which may be responsible for better agreement of results, obtained using S function. Also, present result confirms the validity of present approach in determining the transport properties of alloys like Ni-Cr and Co-Cr.

36 MATERIALS SCIENCE↗

Electronic mechanism for toughness enhancement in Ti{sub x}M{sub 1-x}N (M=Mo and W)

Toughness, besides hardness, is one of the most important properties of wear-resistant coatings. We use ab initio density-functional theory calculations to investigate the mechanical properties of ternary metal nitrides Ti{sub x}M{sub 1-x}N, with M=Mo and W, for x=0.5. Results show that Mo and W alloying significantly enhances the toughness of TiN. The electronic mechanism responsible for this improvement, as revealed by electronic structure calculations, stems from the changes in charge density induced by the additional transition-metal atom. This leads to the formation of a layered electronic arrangement, characterized by strong, respectively, weak, directional bonding, which enables a selective response to strain, respectively, shear, deformations of the structures and yields up to 60% decrease in C{sub 44} values.

36 MATERIALS SCIENCE↗

Development of High Bs Fe-Ni Based Metal Amorphous Nanocomposite by Optimization of Glass Forming Ability

A growing interest in electric vehicles challenges soft magnetic materials to improve efficiency and power density. Metal amorphous nanocomposites (MANCs) have lower coercivities and eddy current losses, allowing for greater efficiency and higher switching frequency. The later allows for high motor speeds and improved power density. However, commercially available and laboratory demonstrated MANCs have shortcomings. Fe-based MANCs, such as FINEMET have excellent magnetic properties, but mechanical properties limit their application in high speed electric motors (HSMs). Fe-Co based MANCs, such as HITPERM, have high saturation inductions and good mechanical properties, but elevated magnetostrictive losses. Co-based MANCs and more recent Fe-Ni based MANCs have low losses and good mechanical properties, but lower saturation inductions (1-1.2 T), that limit power density in HSMs. Recently, much work has explored improving saturation induction in MANCs by increasing the content of magnetic elements, which comes at the cost of glass-forming ability (GFA). These efforts where generally limited to trial and error testing. Additionally, all work to date has focused on Fe-based alloys. In this work, a method of using Thermocalc simulation to locate near-eutectic compositions has been applied to Fe-Ni based alloys. Minima in liquidus temperature and solidification range were found for a ternary composition range and used to identify compositions that retain good GFA as the percentage of magnetic elements is increased. The (Fe 70 Ni 30 ) x (B-Si-Nb) 100-x alloy system for x=82% and x=85% was explored by Thermocalc simulations. This is an increase in magnetic element content compared to previously developed x=80% alloys. 3 compositions in the x=82% system, and 1 alloy in the x=85% system where identified and successfully cast as amorphous ribbon. The amorphous nature of the ribbon was confirmed by a bend test and XRD. Magnetic testing was performed by PPMS to measure saturation induction and Curie temperature of the amorphous material. The Curie temperatures increased to 407-438 °C for the x=82% alloys, and 462 °C for the x=85% alloy. Saturation induction increased to 1.28-1.36 T for the x=82% alloy and 1.48 T for the x=85% alloy, which is a significant improvement over the ~370 °C Curie temperature and 1.2 T saturation of previous Fe-Ni alloy. Crystallization behavior was studied by XRD for the x=85% alloy, showing that crystallization process follows a 2-step process of Amorphous → BCC+FCC+Amorphous → BCC+FCC+Fe 3 B+Fe 23 B 6 . Post annealing magnetic properties were studied by strip testing, and saturation induction as high as 1.48 T was seen after optimal annealing. TEM was used to study structure of as cast and annealed material. 2 alloys with x=82% compositions were identified with an optimal crystalline size of 10-20 nm, while the x=85% alloy had this structure in the as cast state. This opens the possibility of using the alloy in the as cast state, without requiring annealing. In conclusion, alloys with good GFA and improved magnetic properties were identified by Thermocalc simulation.

Krimer, Yuval↗

The effect of fabrication on corrosion in aluminum 2195: Environmental and microstructural considerations

Aluminum alloys containing lithium are particularly attractive to the aerospace structural designer. Lithium's density is only 0.53 g/cc, thus an addition of one weight percent lithium not only increases yield strength, but decreases the density by almost three percent while increasing the modulus by over six percent. The fact that lithium improves these physical properties simultaneously has led to intense study and development of the alloy system. Heretofore, problems in large scale alloy production have retarded commercial development. During the last fifteen years, advances in production technology have rekindled interest in Al-Li alloys, and aluminum suppliers have developed many candidate aerospace materials. However, if these alloys are to be employed successfully, a more complete understanding of their nonequilibrium metallurgy is required. Peel and Starke have each pointed out that an understanding of the weldability of these alloys is a critical step in their implementation. This study addresses the critical lack of information on the environmental compatibility of welded Al 2195 components. Corrosion data for these systems is incomplete, particularly for welded materials exposed to sea water or sea water condensate.

Walsh, Daniel W.↗

Processing of High-Entropy AlCoCr{sub 0.75}Cu{sub 0.5}FeNi Alloy by Spray Forming

Compositionally complex AlCoCrCuFeNi alloy system is one of the extensively studied high-entropy alloys (HEA). Most of these studies have been carried out on as-cast materials that witness slow cooling rate during solidification. In the present investigation, HEA based on AlCoCrCuFeNi system was processed employing spray forming so as to realize its inherent rapid solidification effect and unique microstructural evolution mechanism. The spray formed as well as the as-cast alloys were compared in terms of their microstructural features, phase constitution and hardness. These microstructural features were also compared with that of the overspray powders (< 250 µm) obtained as a by-product of spray forming. Both the as-cast and spray formed alloys showed a mixture of mainly two phases, i.e., face-centered and body-centered cubic (BCC) phases, in contrast to a single BCC phase in overspray powders. However, the spray formed alloy revealed unidentified phases, as against the as-cast material, which disappeared after heat treatment at 1473 K for 3 h. The grain size of the as-cast alloy was around 600-1000 μm compared to a highly refined grain size of 25-30 μm in the as-spray formed alloy. It was found that the hardness of the regions dominated by the constituent phases as well as the bulk of the spray formed material was higher than that of the as-cast alloy. The results validate the efficacy of the process in achieving drastic refinement in grain size, in a single step of large-scale spray forming. The characteristic microstructural features and the phase constitutions have been discussed in light of the prevailing mechanisms of structural evolution and possible solidification phenomena during spray atomization and deposition. This study gives a new direction in processing of these alloys and understanding their solidification behavior under the conditions of layer-by-layer deposition of semi-solid/liquid droplets.

36 MATERIALS SCIENCE↗

Manufacture and engine test of advanced oxide dispersion strengthened alloy turbine vanes

Oxide-Dispersion-strengthened (ODS) Ni-Cr-Al alloy systems were exploited for turbine engine vanes which would be used for the space shuttle thermal protection system. Available commercial and developmental advanced ODS alloys were evaluated, and three were selected based on established vane property goals and manufacturing criteria. The selected alloys were evaluated in an engine test. Candidate alloys were screened by strength, thermal fatigue resistance, oxidation and sulfidation resistance. The Ni-16Cr (3 to 5)Al-ThO2 system was identified as having attractive high temperature oxidation resistance. Subsequent work also indicated exceptional sulfidation resistance for these alloys.

Bailey, P. G.↗

Additive manufacturing of defect-free TiZrNbTa refractory high-entropy alloy with enhanced elastic isotropy via in-situ alloying of elemental powders

Laser powder-bed fusion (L-PBF) additive manufacturing presents ample opportunities to produce net-shape parts. The complex laser-powder interactions result in high cooling rates that often lead to unique microstructures and excellent mechanical properties. Refractory high-entropy alloys show great potential for high-temperature applications but are notoriously difficult to process by additive processes due to their sensitivity to cracking and defects, such as un-melted powders and keyholes. Here, we present a method based on a normalized model-based processing diagram to achieve a nearly defect-free TiZrNbTa alloy via in-situ alloying of elemental powders during L-PBF. Compared to its as-cast counterpart, the as-printed TiZrNbTa exhibits comparable mechanical properties but with enhanced elastic isotropy. This method has good potential for other refractory alloy systems based on in-situ alloying of elemental powders, thereby creating new opportunities to rapidly expand the collection of processable refractory materials via L-PBF.

36 MATERIALS SCIENCE↗

Forging And Milling Contribution On Residual Stresses For A Textured Biphasic Titanium Alloy

Ti-10V-2Fe-3Al is a biphasic titanium alloy ({alpha}+{beta}) used in aeronautical applications for its mechanical properties, such as its yield strength of 1200 MPa and it weighs 40% less than steel. This alloy is particularly useful for vital parts with complex geometry, because of its high forging capability. In order to predict the capability for fatigue lifetime, the designers need to know the residual stresses. X-Ray diffraction is the main experimental technique used to determine residual stresses on the surface. In this case, stress levels are primarily influenced by the complex forging and milling process. On this alloy in particular, it may be difficult to characterize stress due to modification of the microstructure close to the surface. Results obtained by x-ray analysis depend on the correct definition of the shape of the diffraction peaks. The more precisely defined the position of the peak, the more accurately the stresses are evaluated. This paper presents a method to detect if residual stresses can be characterized by x-ray diffraction. The characterization of hardness seems to be a relevant technique to quickly analyze the capability of x-ray diffraction to determine residual stresses.

36 MATERIALS SCIENCE↗

Towards a Superplastic Forming of Fe-Mn-Al Alloys

The aim is to study the characteristics of superplasticity, mostly on non qualified materials, such as austenitic steel of the Fe-Mn-Al alloy, which has some of the specific material parameters closely related to microstructural mechanisms. These parameters are used as indicators of material superplastic potentiality. The material was submitted to hot tensile testing, within a temperature range from 600 deg. C to 1000 deg. C and strain-rates varying from 10{sup -6} to 1 s{sup -1}. The strain rate sensitivity parameter (m) and observed maximum elongation until rupture ({epsilon}{sub r}) could be determined and also obtained from the hot tensile test. The experiments stated a possibility of superplastic behaviour in a Fe-Mn-Al alloy within a temperature range from 700 deg. C to 900 deg. C with grain size around 3 {mu}m (ASTM grain size 12) and average strain rate sensitivity of m {approx} 0.54, as well as a maximum elongation at rupture around 600%. The results are based on a more enhanced research from the authors; however, this paper has focused just on the hot tensile test, as further creep tests results are not available herein. There are rare examples of superplasticity study of an austenitic steel Fe-Mn-Al alloy, thus this work showed some possibility of exploring the potential use of such materials in this regime at temperatures {>=}700 deg. C.

36 MATERIALS SCIENCE↗

On bilinearity of Manson-Coffin low-cycle-fatigue relationship

Some alloy systems, such as aluminum-lithium alloys and dual-phase steels, have been found to show a bilinear Manson-Coffin low-cycle-fatigue relationship. This paper shows that such bilinear behavior is related to the cyclic stress-strain curve. A bilinear cyclic stress-strain curve is a likely indication of a bilinear Manson-Coffin relationship. It is shown that materials other than aluminum-lithium alloys and dual-phase steels also may exhibit bilinear Manson-Coffin behavior. Implications for design are discussed.

Radhakrishnan, V. M.↗

Characterization of Ternary NiTiPt High-Temperature Shape Memory Alloys

Pt additions substituted for Ni in NiTi alloys are known to increase the transformation temperature of the alloy but only at fairly high Pt levels. However, until now only ternary compositions with a very specific stoichiometry, Ni50-xPtxTi50, have been investigated and then only to very limited extent. In order to learn about this potential high-temperature shape memory alloy system, a series of over twenty alloys along and on either side of a line of constant stoichiometry between NiTi and TiPt were arc melted, homogenized, and characterized in terms of their microstructure, transformation temperatures, and hardness. The resulting microstructures were examined by scanning electron microscopy and the phase compositions quantified by energy dispersive spectroscopy."Stoichiometric" compositions along a line of constant stoichiometry between NiTi to TiPt were essentially single phase but by any deviations from a stoichiometry of (Ni,Pt)50Ti50 resulted in the presence of at least two different intermetallic phases, depending on the overall composition of the alloy. Essentially all alloys, whether single or two-phase, still under went a martensitic transformation. It was found that the transformation temperatures were depressed with initial Pt additions but at levels greater than 10 at.% the transformation temperature increased linearly with Pt content. Also, the transformation temperatures were relatively insensitive to alloy stoichiometry within the range of alloys examined. Finally, the dependence of hardness on Pt content for a series of Ni50-xPtxTi50 alloys showed solution softening at low Pt levels, while hardening was observed in ternary alloys containing more than about 10 at.% Pt. On either side of these "stoichiometric" compositions, hardness was also found to increase significantly.

Rios, Orlando↗