Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIRS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Preliminary Air-Flow and Thrust Calibrations of Several Conical Cooling-Air Ejectors with a Primary to Secondary Temperature Ratio of 1.0: Diameter Ratios of 1.06 and 1.40 - 2

An investigation was made of the performance of nine conical cooling-air ejectors at primary jet pressure ratios from 1 to 10, secondary pressure ratios to 4.0, and a temperature ratio of unity. This phase of the investigation was limited to conical ejectors having shroud exit to primary nozzle exit diameter ratios of 1.06 and 1.40, with several spacing ratios for each. The experimental results indicated that the pumping range and amount of cooling-air flow obtained with a 1.06 diameter ratio ejector were relatively small for cooling purposes but that the maximum possible thrust loss, which occurred with no secondary flow, was only 7 percent of convergent nozzle thrust. The 1.40 diameter ratio ejector produced a large cooling air flow and showed a possible thrust loss of 29.5 percent with no cooling air flow. Thrust gains were attained with ejectors of both diameter ratios at secondary pressure ratios greater than 1.0. The limiting primary pressure ratio below which an ejector can operate at a specific secondary pressure ratio (cut-off point) may be estimated for various flight conditions from data contained herein.

Greathouse, W. K.↗

Heat Transfer from High-Temperature Surfaces to Fluids. III - Correlation of Heat-Transfer Data for Air Flowing in Silicon Carbide Tube with Rounded Entrance, Inside Diameter of 3/4 Inch, and Effective Length of 12 Inches: Correlation of Heat-Transfer Data for Air Flowing in Silicon Carbide Tube with Rounded Entrance, Inside Diameter of 3/4 Inch, and Effective Length of 12 Inches - Part 3

A heat-transfer investigation was conducted with air flowing through an electrically heated silicon carbide tube with a rounded entrance, an inside diameter of 3/4 inch, and an effective heat-transfer length of 12 inches over a range of Reynolds numbers up to 300,000 and a range of average inside-tube-wall temperature up to 2500 R. The highest corresponding local outside-tube-wall temperature was 3010 R. Correlation of the heat-transfer data using the conventional Nueselt relation wherein physical properties of the fluid were evaluated at average bulk temperature resulted in a separation of data with tube-wall-temperature level. A satisfactory correlation of the heat-transfer data was obtained, however, by the use of modified correlation parameters wherein the mass velocity G (or product of average air density and velocity evaluated at bulk temperature P(sub b)V(sub b)) in the Reynolds number was replaced by the product of average air velocity evaluated at the bulk temperature and density evaluated at either the average inside-tube-wall temperature or the average film temperature; in addition, all the physical properties of air were correspondingly evaluated at either the average inside-tube-wall temperature or the average film temperature.

Sams, Eldon W.↗

Lessons Learned from AIRS: Improved Determination of Surface and Atmospheric Temperatures Using Only Shortwave AIRS Channels

This slide presentation reviews the use of shortwave channels available to the Atmospheric Infrared Sounder (AIRS) to improve the determination of surface and atmospheric temperatures. The AIRS instrument is compared with the Infrared Atmospheric Sounding Interferometer (IASI) on-board the MetOp-A satellite. The objectives of the AIRS/AMSU were to (1) provide real time observations to improve numerical weather prediction via data assimilation, (2) Provide observations to measure and explain interannual variability and trends and (3) Use of AIRS product error estimates allows for QC optimized for each application. Successive versions in the AIRS retrieval methodology have shown significant improvement.

Susskind, Joel↗

Gulf of Mexico Air Quality: CALIPSO Support for Gulf of Mexico Air Quality Relating to the Deepwater Horizon Oil Spill

On April 20, 2010, an oil platform belonging to BP exploded and leaked a huge volume of oil into the Gulf of Mexico. In an effort to control the spread of the oil, BP applied dispersants such as Corexit and conducted in-situ burnings of the oil. This catastrophe created a complex chain of events that affected not only the fragile water and land ecosystems, but the humans who breathe the air every day. Thousands of people were exposed to fumes associated with oil vapors from the spill, burning of the oil, and the toxic mixture of dispersants. While aiding in clean-up efforts, local fishermen were directly exposure to fumes when working on the Gulf. A notable amount of Gulf Coast residents were also exposed to the oil fumes as seasonal southeasterly winds blew vapors toward land. The Volatile Organic Compounds (VOC) found in oil vapors include: benzene, toluene, ethyl benzene, xylene, naphthalene, hydrogen sulfide and particulate matter (PM). Increases in water temperature and sunlight due to the summer season allow for these VOCs and PM to evaporate into the air more rapidly. Aside from the VOCs found in oil vapors, the dispersant being used to break up the oil is highly toxic and is thought to be even more toxic than the oil itself (EPA website, 2010). To protect human health, the environment, and to make informed policy decisions relevant to the spill, the EPA Region 6 has continuously monitored the affected areas carefully for levels of pollutants in the outdoor air that are associated with petroleum products and the burning of oil along the coast. In an effort to prevent, prepare for, and respond to future oil spills that occur in and around inland waters of the United States, the EPA has been working with local, state, and federal response partners. Air quality measurements were collected by the EPA at five active monitoring systems stationed along the coast.

Nguyen, Myngoc T.↗

Air-To-Air Background Oriented Schlieren Technique

An air-to-air background-oriented Schlieren system and method for measuring and rendering visible density changes in air that cause a refractive index change by an airborne vehicle. A sensor aircraft equipped with a high-speed visible spectrum camera travels at low airspeed on a predetermined route and on a level altitude over a background having consistent contrast and sunlight reflectivity. The target aircraft, traveling on the same predetermined route but at an altitude between the sensor aircraft and the ground (background) passes beneath the sensor aircraft. The camera on the sensor aircraft captures a series of images including a reference image immediately before the target aircraft enters the image frame followed by several data images as the target aircraft passes through the image frame. The data images are processed to calculate density gradients around the target aircraft. These density gradients include shockwaves, vortices, engine exhaust, and wakes. Air density gradients cause a refractive index change in the fluid and a slight distortion in the background pattern of the data image. Image processing that compares the data image to the reference image yields the difference caused by the density gradient.

Heineck, James Thomas↗

Learning Based Edge Computing in Air-to-Air Communication Network

This paper studies learning-based edge computing and communication in a dynamic Air-to-Air Ad-hoc Network (AAAN). Due to spectrum scarcity, we assume the number of Air-to-Air (A2A) communication links is greater than that of the available frequency channels, such that some communication links have to share the same channel, causing co-channel interference. We formulate the joint channel selection and power control optimization problem to maximize the aggregate spectrum utilization efficiency under resource and fairness constraints. A distributed deep Q learning-based edge computing and communication algorithm is proposed to find the optimal solution. In particular, we design two different neural network structures and each communication link can converge to the optimal operation by exploiting only the local information from its neighbors, making it scalable to large networks. Finally, experimental results demonstrate the effectiveness of the proposed solution in various AAAN scenarios.

Zhe Wang↗

Delaware Basin Health and Air Quality: Spatiotemporal Analysis of Air Pollutants Collected from Ground and Space Instruments Around the Guadalupe Mountains and Carlsbad Caverns National Parks

Nitrogen dioxide (NO2) is a precursor for secondary air pollutants, which are associated with decreased visibility, and decreased ecosystem and respiratory health. NO2 is a growing threat to national parks within the Delaware Basin where nearby oil and gas activity contributes to deteriorating park conditions, implying adverse effects on the local tourism economy and public health. To demonstrate spatial and temporal patterns of air pollution in the parks, we examined average monthly, seasonal, and annual tropospheric column concentrations of NO2 in Carlsbad Caverns (CAVE) and Guadalupe Mountain (GUMO) National Parks. We used both the NASA Ozone Monitoring Instrument (OMI) and the European Space Agency (ESA) Tropospheric Monitoring Instrument (TROPOMI) to map NO2 tropospheric column densities. Using ground-based emissions values from the Environmental Protection Agency National Emissions Inventory (NEI) for two nearby natural gas processing plants (Indian Basin Gas Plant, South Carlsbad Plant), we extrapolated monthly trends from these point sources and compared seasonal emissions levels with the measurements recorded by OMI and TROPOMI. The NEI data show an 8% increase in flaring from 2013–2021. OMI measured a 38.3% NO2 increase over the Delaware Basin, 15.29% increase over CAVE, and 4.26% decrease over GUMO from 2011–2018. TROPOMI measured a -1% NO2 change over the Delaware Basin, 3% over CAVE, and 7% over GUMO from 2018–2020. The analysis indicates a positive correlation between emissions from fossil fuel exploration and NO2 concentrations above CAVE and GUMO. This information will inform National Park Service air quality monitoring and policy efforts to ensure compliance with the Clean Air Act.

Sean Cusick↗

A Safety-Driven Approach to Exploring and Comparing Air Traffic Management Concepts for Enabling Urban Air Mobility

There is broad recognition that the high tempo and density of Urban Air Mobility (UAM) operations will require identifying new Air Traffic Management (ATM) concepts to safely integrate UAM air traffic into the airspace alongside existing air traffic. However, the simulation models used to compare ATM concepts today are difficult to apply during the early stages of concept development and do not offer enough support in identifying potential new concepts. In addition, they have limited ability to evaluate ATM concepts in terms of safety, security, and other key emergent properties. Instead of using simulation to evaluate ATM concepts, this paper demonstrates how a safety-driven systems engineering approach based on Systems-Theoretic Accident Model and Processes (STAMP) can be used to design properties such as safety into an ATM system from the earliest stages of development. Using a hazard analysis technique called Systems-Theoretic Process Analysis (STPA), system requirements and the desired ATM behavior are derived. As an example, two possible ATM concepts to implement that behavior are compared to identify their safety-related benefits and tradeoffs. This new approach enables (1) systematic exploration of alternative ATM concepts and (2) identification of the safety-related tradeoffs between concepts as early as possible in the development process.

system safety↗

High-Power Zinc-Air Energy Storage: Enhanced Metal-Air Energy Storage System with Advanced Grid-Interoperable Power Electronics Enabling Scalability and Ultra-Low Cost

GRIDS Project: Fluidic is developing a low-cost, rechargeable, high-power module for Zinc-air batteries that will be used to store renewable energy. Zinc-air batteries are traditionally found in small, non-rechargeable devices like hearing aids because they are well-suited to delivering low levels of power for long periods of time. Historically, Zinc-air batteries have not been as useful for applications which require periodic bursts of power, like on the electrical grid. Fluidic hopes to fill this need by combining the high energy, low cost, and long run-time of a Zinc-air battery with new chemistry providing high power, high efficiency, and fast response. The battery module could allow large grid-storage batteries to provide much more power on very short demand—the most costly kind of power for utilities—and with much more versatile performance.

ARPA-E↗

Metal-Air Electric Vehicle Battery: Sustainable, High-Energy Density, Low-Cost Electrochemical Energy Storage – Metal-Air Ionic Liquid (MAIL) Batteries

Broad Funding Opportunity Announcement Project: ASU is developing a new class of metal-air batteries. Metal-air batteries are promising for future generations of EVs because they use oxygen from the air as one of the battery’s main reactants, reducing the weight of the battery and freeing up more space to devote to energy storage than Li-Ion batteries. ASU technology uses Zinc as the active metal in the battery because it is more abundant and affordable than imported lithium. Metal-air batteries have long been considered impractical for EV applications because the water-based electrolytes inside would decompose the battery interior after just a few uses. Overcoming this traditional limitation, ASU’s new battery system could be both cheaper and safer than today’s Li-Ion batteries, store from 4-5 times more energy, and be recharged over 2,500 times.

ARPA-E↗

Air-to-air background oriented schlieren technique

An air-to-air background-oriented Schlieren system and method for measuring and rendering visible density changes in air that cause a refractive index change by an airborne vehicle. A sensor aircraft equipped with a high-speed visible spectrum camera travels at low airspeed on a predetermined route and on a level altitude over a background having consistent contrast and sunlight reflectivity. The target aircraft, traveling on the same predetermined route but at an altitude between the sensor aircraft and the ground (background) passes beneath the sensor aircraft. The camera on the sensor aircraft captures a series of images including a reference image immediately before the target aircraft enters the image frame followed by several data images as the target aircraft passes through the image frame. The data images are processed to calculate density gradients around the target aircraft. These density gradients include shockwaves, vortices, engine exhaust, and wakes. Air density gradients cause a refractive index change in the fluid and a slight distortion in the background pattern of the data image. Image processing that compares the data image to the reference image yields the difference caused by the density gradient.

Heineck, James Thomas↗

Bayesian modeling of traffic-related air pollutants: A case study of urban transportation and air quality dynamics in Columbia, South Carolina

Traffic emissions significantly impact near-road air quality and public health. This research applies a Bayesian modeling framework to investigate these impacts using high-resolution traffic and air pollutant data from an urban corridor in Columbia, South Carolina. Despite a data collection period truncated by the COVID-19 lockdown, the Bayesian approach successfully identified significant predictors and quantified model uncertainty. Employing Bayesian Model Selection and Averaging enhanced prediction accuracy and evaluated model uncertainty. Findings indicate that higher temperatures and increased moisture levels elevate particulate matter (PM 1.0 , PM 2.5 , PM 10 ) concentrations, while traffic speed significantly affects nitrogen dioxide (NO 2 ) levels. Specifically, higher average traffic speeds (indicative of smoother flow) correspond to lower NO 2 concentrations, suggesting that less congested conditions reduce NO 2 emissions. This study highlights the robustness of Bayesian methods for generating reliable air quality insights even under data-constrained conditions. The findings underscore the importance of traffic flow management (e.g., reducing congestion) for mitigating near-road NO 2 exposure and provide a basis for developing targeted public health strategies.

54 ENVIRONMENTAL SCIENCES↗

Machine learning based simultaneous control of air handling unit discharge air and condenser water temperatures set-point for minimized cooling energy in an office building

In this study, an artificial intelligence based real-time prediction and control model to optimize condenser water temperature and discharge air temperature (DAT) set-points in water-cooled air handling unit (AHU) system has been developed. EnergyPlus-MATLAB co-simulation has been conducted to analyze the developed model's effectiveness. Here, to develop artificial neural networks (ANN) model, embedded neural network objects in MATLAB was utilized. The developed model could decide an optimal temperature set-points based on outdoor air wet-bulb temperature to reflect the Korean climate context. As a result, the developed ANN prediction model showed the predictive performance of Cv(RMSE) of approximately 21%. Compared to the conventional fixed temperature algorithm, which fixes AHU DAT at 14°C and condenser water temperature at 32°C, the ANN based optimized control showed a 22% total cooling energy reduction. These results show that significant energy savings can be achieved by simultaneously controlling condenser water temperature and AHU DAT set-points considering Korean climatic characteristics using AI technologies such as ANN models.

24 POWER TRANSMISSION AND DISTRIBUTION↗

An Interface Specification for Urban Air Mobility Performance Models to Support Air Traffic Management Research

Performance modeling of Urban Air Mobility vehicles in support of Air Traffic Management research poses new challenges. These aircraft often rely on a combination of fixed-wing and rotorcraft performance capabilities to enable a new and still-evolving concept of high-volume operations in densely populated areas. These characteristics lead to variability in performance model format and functionality, complicating model development and leading to difficulties for users integrating the models into their applications. This paper describes an interface specification for performance models that is intended to help address this issue. The interface aims to support the core functionality of performance models while also providing the necessary flexibility to both model developers and users. The specification describes the required model documentation, required inputs to the model, and required outputs from the model in general terms that are adaptable to most programming languages. The utilization of an appropriate interface specification will support the development of an Urban Air Mobility performance model database and help to improve interoperability of these models for a broad array of user applications.

Trajectory Prediction↗

An Interface Specification for Urban Air Mobility Performance Models to Support Air Traffic Management Research

Performance modeling of Urban Air Mobility vehicles in support of Air Traffic Management research poses new challenges. These aircraft often rely on a combination of fixed-wing and rotorcraft performance capabilities to enable a new and still-evolving concept of high-volume operations in densely populated areas. These characteristics lead to variability in performance model format and functionality, complicating model development and leading to difficulties for users integrating the models into their applications. This paper describes an interface specification for performance models that is intended to help address this issue. The interface aims to support the core functionality of performance models while also providing the necessary flexibility to both model developers and users. The specification describes the required model documentation, required inputs to the model, and required outputs from the model in general terms that are adaptable to most programming languages. The utilization of an appropriate interface specification will support the development of an Urban Air Mobility performance model database and help to improve interoperability of these models for a broad array of user applications.

Trajectory Prediction↗

Air transport of plutonium metal: content expansion initiative for the plutonium air transportable (PAT01) packaging

The National Nuclear Security Administration (NNSA) has submitted an application to the Nuclear Regulatory Commission (NRC) for the air shipment of plutonium metal within the Plutonium Air Transportable (PAT-1) packaging. The PAT-1 packaging is currently authorized for the air transport of plutonium oxide in solid form only. The INMM presentation will provide a limited overview of the scope of the plutonium metal initiative and provide a status of the NNSA application to the NRC.

99 GENERAL AND MISCELLANEOUS↗

Air transport of plutonium metal : content expansion initiative for the Plutonium Air Transportable (PAT-1) packaging.

The National Nuclear Security Administration (NNSA) has submitted an application to the Nuclear Regulatory Commission (NRC) for the air shipment of plutonium metal within the Plutonium Air Transportable (PAT-1) packaging. The PAT-1 packaging is currently authorized for the air transport of plutonium oxide in solid form only. The INMM presentation will provide a limited overview of the scope of the plutonium metal initiative and provide a status of the NNSA application to the NRC.

36 MATERIALS SCIENCE↗

Atomically Thin Mesoporous Co 3 O 4 Layers Strongly Coupled with N-rGO Nanosheets as High-Performance Bifunctional Catalysts for 1D Knittable Zinc-Air Batteries [Atomically Thin Mesoporous Co 3 O 4 /N-rGO Nanosheets as the Bifunctional Catalysts for One-Dimensional Knittable Zinc-Air Batteries]

Here, under development for next–generation wearable electronics are flexible, knittable, and wearable energy–storage devices with high energy density that can be integrated into textiles. Herein, knittable fiber–shaped zinc–air batteries with high volumetric energy density (36.1 mWh cm –3 ) are fabricated via a facile and continuous method with low–cost materials. Furthermore, a high–yield method is developed to prepare the key component of the fiber–shaped zinc–air battery, i.e., a bifunctional catalyst composed of atomically thin layer–by–layer mesoporous Co 3 O 4 /nitrogen–doped reduced graphene oxide (N–rGO) nanosheets. Benefiting from the high surface area, mesoporous structure, and strong synergetic effect between the Co 3 O 4 and N–rGO nanosheets, the bifunctional catalyst exhibits high activity and superior durability for oxygen reduction and evolution reactions. Compared to a fiber–shaped zinc–air battery using state–of–the–art Pt/C + RuO 2 catalysts, the battery based on these Co 3 O 4 /N–rGO nanosheets demonstrates enhanced and stable electrochemical performance, even under severe deformation. Such batteries, for the first time, can be successfully knitted into clothes without short circuits under external forces and can power various electronic devices and even charge a cellphone.

36 MATERIALS SCIENCE↗