Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “smoothing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

The least squares process of MEDIA for computing DRVID calibration polynomials

A process is described and evaluated for computing a least squares polynomial approximation of data points in which the optimum degree of the polynomial is automatically determined. An iterative smoothing technique is used to replace every point with the value taken on by a moving least squares polynomial computed from a subset of points centered at the point to be replaced. The optimum degree of the resulting polynomial approximation is determined by analyzing the finite differences of each successive set of smoothed points. To evaluate the process, both artificially constructed data and actual Mariner Mars 1971 (MM'71) tracking data are used. This process was incorporated into a transmission media calibration computer program (MEDIA), which calibrates radiometric data to overcome the effects on the tracking signal of charged particle media. MEDIA was used in support of MM'71.

Leavitt, R. K.↗
NASA NTRS1971

Sensitivity of the creep-rupture properties of Waspaloy sheet to sharp-edged notches in the temperature range 1000-1400 deg F.

Time-dependent notch sensitivity of Waspaloy was observed at test temperatures from 1000 to 1300 deg F. Its occurrence in this range was dependent on the heat treatment. ?Overaging' eliminated the notch sensitivity. Optimum combination of smooth and notched specimen strengths for material solution treated at 1975 deg F were obtained by aging 24 hr at 1550 deg F. Necessary conditions for time-dependent notch sensitivity were (1) the notch specimen loads had to be below the approximate 0.2 percent offset yield strength; and (2 ) test data from smooth specimens had to indicate that small amounts of creep used up large fractions of creep-rupture life. No reasons were evident why these criteria will not prove applicable to other alloys.

Wilson, D. J.↗
NASA NTRS1972

Effect of thermally expanding surfaces on aerodynamic roll torques for cones.

An experimental and analytical study has been made of the aerodynamic roll torque on smoothly ablating, spinning cones. The tests, conducted in the Ames 3.5-Foot Hypersonic Wind Tunnel, indicated that the smoothly ablating model rolling at 0 deg angle of attack experiences roll damping, but when rolling at angle of attack an aerodynamic torque in the direction of spin arises if thermal expansion of the body surface occurs. An analysis of the spinning body at angle of attack is included to show how the relative importance of the ablator thermal expansion and the surface recession rate determines whether the motion is damped or undamped.

Mcdevitt, J. B.↗
NASA NTRS1972

Photodissociation of CO2 to produce CO /a super 3 pi/.

Carbon dioxide in a helium buffer at room temperature was irradiated with a photon beam. The wavelengths used in the investigation were in the range from 850 to 1090 A. Phosphorescence from CO Cameron bands was observed. The phosphorescent yield is zero at threshold and increases smoothly to a maximum of about 60% near 900 A. The smoothness of the percentage yield was an unexpected observation and is explained by postulating that the relevant potential surface crossings are outside the Franck-Condon region of carbon dioxide absorption.

Lawrence, G. M.↗
NASA NTRS1972

Time-dependent edge-notch sensitivity of oxide and gamma prime dispersion strengthened sheet materials at 1000 to 1800 F (538 - 982 C)

Research was carried out to determine whether an oxide dispersion hardened alloy, TD-Ni, Cr, and low volume fraction gamma prime strengthened nickel-base alloy, Modified Waspaloy, were susceptible to time-dependent edge-notch sensitivity. The results were evaluated in terms of the mechanical characteristics of the alloys and the dislocation motion mechanisms operative. As far as could be determined, the results of the investigation were consistent with the following important concepts developed for Waspaloy and Inconel 718: (1) Time-dependent edge-notch sensitivity occurs when notched specimens are loaded below the approximate 0.2 percent smooth specimen offset yield strength and when data from smooth specimens indicate that small amounts of creep consume large rupture life fractions. (2) When precipitate particles are sheared by dislocations, the deformation is localized and time-dependent notch sensitivity occurs. When dislocations by-pass precipitate particles the deformation is homogeneous. Under these conditions, no time-dependent notch sensitivity has been observed.

Wilson, D. J.↗
NASA NTRS1972

Low-speed aerodynamic characteristics of an airfoil optimized for maximum lift coefficient

An investigation has been conducted in the Langley low-turbulence pressure tunnel to determine the two-dimensional characteristics of an airfoil optimized for maximum lift coefficient. The design maximum lift coefficient was 2.1 at a Reynolds number of 9.7 million. The airfoil with a smooth surface and with surface roughness was tested at angles of attack from 6 deg to 26 deg, Reynolds numbers (based on airfoil chord) from 2.0 million to 12.9 million, and Mach numbers from 0.10 to 0.35. The experimental results are compared with values predicted by theory. The experimental pressure distributions observed at angles of attack up to at least 12 deg were similar to the theoretical values except for a slight increase in the experimental upper-surface pressure coefficients forward of 26 percent chord and a more severe gradient just behind the minimum-pressure-coefficient location. The maximum lift coefficients were measured with the model surface smooth and, depending on test conditions, varied from 1.5 to 1.6 whereas the design value was 2.1.

Bingham, G. J.↗
NASA NTRS1973

Microwave emission and scattering from vegetated terrain

Models are developed for the apparent temperature and backscattering coefficient of vegetated terrain to illustrate the effects of vegetation on the sensitivity of these parameters to variations of soil moisture. Three types of terrain are simulated for both the passive and the active case: a uniform canopy over a smooth surface, plant rows on a smooth surface, and plant rows on a rough surface. In each case the canopy is defined by its overall dimensions and by its electric permittivity, which is determined from Weiner model for dielectric mixture. Emission and scattering from both the soil and the canopy are considered, but atmospheric effects are neglected. Calculated data indicate that the sensitivity of the apparent temperature and backscattering coefficient to variations of soil moisture, decreases as the amount of vegetation increases. It is shown that the same effect results from increasing signal frequency or angle of incidence.

Sibley, T. G.↗
NASA NTRS1972

Status of STOL ride quality and control

A STOL ride-control development program has been initiated with the objective of generating ride-control technology through development and evaluation of an active control system specifically designed to provide ride smoothing on a STOL vehicle. Although much can be learned through analysis, there are deficiencies in technology for translating analysis results into operating hardware. The general approach being followed is to select an existing STOL vehicle for trial and then carry out a study to establish feasibility of a control system or systems to smooth the ride and generate system trade-off data.

Conner, D. W.↗
NASA NTRS1973

On the relation between solar wind structure and solar wind rotational and tangential discontinuities.

Solar wind plasma and magnetic field data were used to identify rotational and tangential discontinuities during the first 40 days of the flight of Mariner 5. Of the 40 rotational discontinuities found, 36 were clustered in three distinct 3- to 6-day intervals. These three intervals were characterized by high solar wind bulk velocities, high magnetic field magnitudes, low densities, high correlation between velocity and magnetic field changes, and the presence of smooth Alfven waves. The rotational discontinuities had magnetic field changes that were generally close to the direction of magnetic field changes for smooth Alfven waves. Although the primary component of these changes was perpendicular to the equatorial plane for both, the radial component for the discontinuities was generally larger. The normals to the tangential discontinuity surfaces strongly preferred a direction near the ecliptic plane and perpendicular to the spiral field direction.

Turner, J. M.↗
NASA NTRS1973

Precise calculation of the magnetosphere surface for a tilted dipole.

The shape of the magnetosphere has been calculated self-consistently for inclinations of the earth's magnetic dipole from perpendicular to the solar wind. Inclination angles of 0-35 deg have been chosen in steps of 5 deg and various smooth trends in the surface characteristics with increasing inclination angle noted. The surface points and the complete field at the surface points have been calculated for the entire surfaces. The neutral point region has been given precise study in one degree steps and is found to be tangent to the solar wind velocity and to have a smooth continuous curvature.

Choe, J. Y.↗
NASA NTRS1973

Evaluation of Stress Corrosion Cracking Susceptibility Using Fracture Mechanics Techniques, Part 1

Stress corrosion cracking (SSC) tests were performed on 13 aluminum alloys, 13 precipitation hardening stainless steels, and two titanium 6Al-4V alloy forgings to compare fracture mechanics techniques with the conventional smooth specimen procedures. Commercially fabricated plate and rolled or forged bars 2 to 2.5-in. thick were tested. Exposures were conducted outdoors in a seacoast atmosphere and in an inland industrial atmosphere to relate the accelerated tests with service type environments. With the fracture mechanics technique tests were made chiefly on bolt loaded fatigue precracked compact tension specimens of the type used for plane-strain fracture toughness tests. Additional tests of the aluminum alloy were performed on ring loaded compact tension specimens and on bolt loaded double cantilever beams. For the smooth specimen procedure 0.125-in. dia. tensile specimens were loaded axially in constant deformation type frames. For both aluminum and steel alloys comparative SCC growth rates obtained from tests of precracked specimens provide an additional useful characterization of the SCC behavior of an alloy.

Sprowls, D. O.↗
NASA NTRS1973

Optimization of self-acting herringbone journal bearing for maximum stability

Groove parameters were determined to maximize the stability of herringbone grooved journal bearings. Parameters optimized were groove depth, width, length, and angle. Optimization was performed using a small eccentricity, infinite groove analysis in conjunction with: (1) a previously developed Newton-Raphson procedure for bearings with the smooth member rotating or with the grooved member rotating at low compressibility numbers, and (2) a newly-developed vector technique for bearings with the grooved member rotating at high compressibility numbers. The design curves enable one to choose the optimum bearing for a wide range of operating conditions. These include: (1) compressibility numbers from 0 (incompressible) to 80, (2) length to diameter ratios from 1/4 to 2, and (3) smooth or grooved member rotating. Compared to bearings optimized to maximize load capacity, bearings optimized for stability: (1) allow a thousandfold increase in bearing-supported mass in some cases before onset of instability (the most dramatic increase are for bearings with small L/D operating at high compressibility numbers), and (2) lose no more than 77-percent of their load capacity in any case studied. Stability is much greater when the grooved member rotates.

Fleming, D. P.↗
NASA NTRS1973

High temperature, low cycle fatigue of copper-base alloys in argon. Part 3: Zirconium-copper; thermal-mechanical strain cycling, hold-time and notch fatigue results

The low-cycle fatigue characteristics of smooth bar and notched bar specimens (hourglass shape) of zirconium-copper, 1/2 Hard, material (R-2 Series) were evaluated at room temperature in axial strain control. Over the fatigue life range from about 300 to 3000 cycles the ratio of fatigue life for smooth bar to fatigue life for notched bar remained constant at a value of about 6.0. Some additional hold-time data for the R-2 alloy tested in argon at 538 C are reported. An analysis of the relaxation data obtained in these hold-time tests is also reported and it is shown that these data yield a fairly consistent correlation in terms of instantaneous stress rate divided by instantaneous stress. Two thermal-mechanical strain cycling tests were also performed using a cyclic frequency of 4.5 cycles per hour and a temperature cycling interval from 260 to 538 C. The fatigue life values in these tests were noticeably lower than that observed in isothermal tests at 538 C.

Conway, J. B.↗
NASA NTRS1973

Experimental and data analysis techniques for deducing collision-induced forces from photographic histories of engine rotor fragment impact/interaction with a containment ring

An analysis method termed TEJ-JET is described whereby measured transient elastic and inelastic deformations of an engine-rotor fragment-impacted structural ring are analyzed to deduce the transient external forces experienced by that ring as a result of fragment impact and interaction with the ring. Although the theoretical feasibility of the TEJ-JET concept was established, its practical feasibility when utilizing experimental measurements of limited precision and accuracy remains to be established. The experimental equipment and the techniques (high-speed motion photography) employed to measure the transient deformations of fragment-impacted rings are described. Sources of error and data uncertainties are identified. Techniques employed to reduce data reading uncertainties and to correct the data for optical-distortion effects are discussed. These procedures, including spatial smoothing of the deformed ring shape by Fourier series and timewise smoothing by Gram polynomials, are applied illustratively to recent measurements involving the impact of a single T58 turbine rotor blade against an aluminum containment ring. Plausible predictions of the fragment-ring impact/interaction forces are obtained by one branch of this TEJ-JET method; however, a second branch of this method, which provides an independent estimate of these forces, remains to be evaluated.

Yeghiayan, R. P.↗
NASA NTRS1974

A method for the measurement and the statistical analysis of atmospheric turbulence

The instantaneous values of output voltages representing the wind velocity vector and the temperature at different elevations of the 250-foot meteorological tower located at NASA Wallops Flight Center are provided with the three dimensional split-film TSI Model 1080 anemometer system. The output voltages are sampled at a rate of one every 5 milliseconds, digitized and stored on digital magnetic tapes for a time period of approximately 40 minutes, with the use of a specially designed data acqusition system. A new calibration procedure permits the conversion of the digital voltages to the respective values of the temperature and the velocity components in a Cartesian coordinate system connected with the TSI probe with considerable accuracy. Power, cross, coincidence and quadrature spectra of the wind components and the temperature are obtained with the use of the fast Fourier transform. The cosine taper data window and ensemble and frequency smoothing techniques are used to provide smooth estimates of the spectral functions.

Tieleman, H. W.↗
NASA NTRS1973

Characterization of nickel-copper alloy specimens processed as a part of the M553 sphere forming experiment during the Skylab 1 and 2 flight

Both processed nickel-copper alloy specimens apparently completely melted by the electron beam in the Skylab M512 materials processing facility and either floated free in space, but collided with some smooth flat surface before solidifying, or remained attached to its support post during solidification. Both specimens had a smooth flat area on the surface due to this adherence during solidification. The nominal composition of the alloy before processing in space was 70 percent Ni and 30 percent Cu. Tests show that a considerable amount of copper was lost during processing by evaporation. It was further found that less copper was present in the cap areas, particularly at the surface, than was in the remainder of the specimens. The microchemistry of the dendrites and interdendritic regions, however, is in agreement with the phase diagram for this alloy. The measured densities of these specimens were less than the theoretical density of the alloy due to the amount of porosity present, however, no large voids were found by radiographic techniques.

Hubbard, J. L.↗
NASA NTRS1973

Evaluation of fatigue-crack growth rates by polynomial curve fitting

Fundamental characterization of the constant-amplitude fatigue crack propagation is achieved by an analysis of the rate of change of crack length with change in number of applied loading cycles, defining the rate values such that they are consistent with the basic assumption of smoothness and continuity in the fatigue crack growth process. The technique used to satisfy the analytical conditions and minimize the effects of local material anomalies and experimental errors is that of fitting a smooth curve to the entire set of basic data by least square regression. This yields a well-behaved function relating the number of cycles to the crack length. By taking the first derivative of the function, the crack growth rate is obtained for each point. The class of curve fitting functions used in the analysis is the polynomial of degree n.

Davies, K. B.↗
NASA NTRS1973

A catalog of ionospheric F region irregularity behavior based on Ogo 6 retarding potential analyzer data

Review of in situ data obtained with the aid of the retarding potential analyzer on board Ogo 6 which reveal the nature of ionospheric irregularities in the total ion concentration above 400 km. Except for the high-latitude regions, the ionosphere is usually observed to be very smooth in the daytime, but considerable structure is observed at night, particularly near the equator and at Atlantic longitudes. Although most of the irregularities observed appear to be stochastic in nature, many nearly monochromatic waveforms are observed near the equator. The topics discussed include the midlatitude scintillation boundary, large-amplitude equatorial irregularities, the fluctuation spectrum of typical F-region irregularities, the lower edge of the equatorial F region, sinusoidal waveforms, ground glass irregularities, breaking wave irregularities, and regions of smooth and irregular ionization inside the polar cap.

Mcclure, J. P.↗

Refine your search to explore more results.