Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “small wind”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

The Gravity and Extreme Magnetism Small Explorer (GEMS)

The Gravity and Extreme Magnetism Small Explorer (GEMS) was selected by NASA for flight in 2014 to make a sensitive search for X-ray polarization from a wide set of source classes, including stellar black holes, Seyfert galaxies and quasars, blazars, rotation and accretion-powered pulsars, magnetars, shell supernova remnants and pulsar wind nebulae. Among the primary scientific objectives are determining the effects of the spin of black holes and the geometry of supermassive black hole accretion, determining the configurations of the magnetic fields and the X-ray emission of magnetars, and determining the magnetic structure of the supernova shocks in which cosmic rays are accelerated. GEMS will observe 23 targets during a 16 month prime mission, in observations that will be able to reach predicted levels of polarization. The mission can be extended to provide a guest observer phase. The GEMS instrument has time projection chamber polarimeters with high 2-10 keV efficiency at the focus of thin foil mirrors. The 4.5 m focal length mirrors will be deployed on an extended boom. The spacecraft with the instrument is rotated with a period of about 10 minutes to enable measurement and correction of systematic errors. A small Bragg reflection soft X-ray experiment takes advantage of this rotation to obtain a measurement at 0.5 keV. The design of the GEMS instrument and the mission, the expected performance and the planned science program will be discussed.

Kallman, T. R.↗
NASA NTRS2016

Contributions of Solar Wind and Micrometeoroids to Molecular Hydrogen in the Lunar Exosphere

We investigate the density and spatial distribution of the H2 exosphere of the Moon assuming various source mechanisms. Owing to its low mass, escape is non-negligible for H2. For high-energy source mechanisms, a high percentage of the released molecules escape lunar gravity. Thus, the H2 spatial distribution for high-energy release processes reflects the spatial distribution of the source. For low energy release mechanisms, the escape rate decreases and the H2 redistributes itself predominantly to reflect a thermally accommodated exosphere. However, a small dependence on the spatial distribution of the source is superimposed on the thermally accommodated distribution in model simulations, where density is locally enhanced near regions of higher source rate. For an exosphere accommodated to the local surface temperature, a source rate of 2.2 g s-1 is required to produce a steady state density at high latitude of 1200 cm-3. Greater source rates are required to produce the same density for more energetic release mechanisms. Physical sputtering by solar wind and direct delivery of H2 through micrometeoroid bombardment can be ruled out as mechanisms for producing and liberating H2 into the lunar exosphere. Chemical sputtering by the solar wind is the most plausible as a source mechanism and would require 10-50 of the solar wind H+ inventory to be converted to H2 to account for the observations.

Impact↗
NASA NTRS1995

The location of planetary bow shocks: A critical overview of theory and observations

A bow shock (BS has been observed in the collisionless solar wind upstream of every planet except Pluto, which has yet to be visited by a spacecraft. They are all of similar character, but their size relative to the planet varies widely, e.g., the planeto-centric distance to the BS nose ranges from about 1.4 R(sub V) for Venus to 88 R(sub J) or more for Jupiter. Comparisons are reviewed that show its location may be represented satisfactorily by a gasdynamic (GD) model, provided the properties of the solar wind and planetary magnetic field and ionosphere are known and used as input in the application. Factors that determine the location are discussed, and examples are presented to illustrate effects of their variation, including which part of a BS is influenced by a local variation of the magneto/ionopause (MIP) shape. The interplanetary magnetic field (IMF) has no influence on the BS location in the GD model, but is shown to have a small effect in corresponding solutions of the basic MHD model from which the GD model is derived as the limit for weak IMF. Nearly all GD and MHD solutions are for steady flow, but a solution for unsteady flow associated with the passage of an interplanetary shock is also presented. It shows that the BS moves rapidly from its initial to final location, e.g., in about minute for the earth. Since many changes in the solar wind occur over longer intervals, these results help explain the success of quasi-stationary solutions in modeling the BS in time-varying solar wind flows.

Spreiter, J. R.↗
DOE OSTI2021

Substitution of virgin carbon fiber with low-cost recycled fiber in automotive grade injection molding polyamide 66 for equivalent composite mechanical performance with improved sustainability

Recycled carbon fiber has historically proven challenging to integrate into composite manufacturing due in no small part to the low-density, randomly oriented, discontinuous fiber format that results from typical recycling. Discontinuous fiber requires the use of alternative technologies than those traditionally applied to continuous fiber (e.g., hand lay-up, winding). Extrusion compounding is one such applicable technology, but material transfer into the system requires alternative feeding equipment or the use of an altered procedure as trialed in this research. In this study, an injection molding compound for automotive applications was prepared with recycled carbon fiber and compared against an existing commercial compound. Input fibers and molded compound were evaluated for mechanical performance, while relevant variables such as compounded fiber alignment and aspect ratio were compared to the existing baseline material to confirm a like-for-like composite material structure. Overall, analysis indicates that recycled fiber performs similarly to virgin fiber reinforcement, demonstrating that recycled fiber may be a viable drop-in replacement for short-fiber discontinuous applications.

42 ENGINEERING↗
DOE OSTI2024

Active nematic ratchet in asymmetric obstacle arrays

We numerically investigate the effect of an asymmetric periodic obstacle array in a two-dimensional active nematic. We find that activity in conjunction with the asymmetry leads to a ratchet effect or unidirectional flow of the fluid along the asymmetry direction. The directional flow is still present even in the active turbulent phase when the gap between obstacles is sufficiently small. We demonstrate that the dynamics of the topological defects transition from flow mirroring to smectic-like as the gap between obstacles is made smaller, and explain this transition in terms of the pinning of negative winding number defects between obstacles. This also leads to a nonmonotonic ratchet effect magnitude as a function of obstacle size, so that there is an optimal obstacle size for ratcheting at fixed activity.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Shallow Cumulus Properties as Captured by Adiabatic Fraction in High-Resolution LES Simulations

Abstract Shallow convective clouds are important players in Earth’s energy budget and hydrological cycle, and are abundant in the tropical and subtropical belts. They greatly contribute to the uncertainty in climate predictions due to their unresolved, complex processes that include coupling between the dynamics and microphysics. Analysis of cloud structure can be simplified by considering cloud motions as a combination of moist adiabatic motions like adiabatic updrafts and turbulent motions leading to deviation from adiabaticity. In this work, we study the sizes and occurrence of adiabatic regions in shallow cumulus clouds during their growth and mature stages, and use the adiabatic fraction (AF) as a continuous metric to describe cloud processes and properties from the core to the edge. To do so, we simulate isolated trade wind cumulus clouds of different sizes using the System of Atmospheric Modeling (SAM) model in high resolution (10 m) with the Hebrew University spectral bin microphysics (SBM). The fine features in the clouds’ dynamics and microphysics, including small near-adiabatic volumes and a thin transition zone at the edge of the cloud (∼20–40 m in width), are captured. The AF is shown to be an efficient measure for analyzing cloud properties and key processes determining the droplet-size distribution formation and shape during the cloud evolution. Physical processes governing the properties of droplet size distributions at different cloud regions (e.g., core, edge) are analyzed in relation to AF. Significance Statement 1) This study investigates the evolution of cumulus clouds (Cu) using a 10-m-resolution LES model with spectral bin microphysics. 2) The study improves the understanding of the mutual effects of adiabatic updrafts and lateral entrainment and mixing. 3) The study demonstrates the existence of an adiabatic core in nonprecipitating Cu. 4) Shapes of the droplet size distributions are closely related to the adiabatic fraction values. 5) Utilization of high resolution reveals the existence of physically significant small features in the cloud structure, such as a narrow cloud interface zone and small adiabatic volumes.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1978

Composite hub/metal blade compressor rotor

A low cost compressor rotor was designed and fabricated for a small jet engine. The rotor hub and blade keepers were compression molded with graphite epoxy. Each pair of metallic blades was held in the hub by a keeper. All keepers were locked in the hub with circumferential windings. Feasibility of fabrication was demonstrated in this program.

Yao, S.↗
NASA NTRS1982

A possible common origin for the rare gases on Venus, earth, and Mars

The rare gas concentrations in the terrestrial planets and the carbonaceous chondrites could have been derived from a single source an early solar wind. The fractionation processes responsible for the varying concentration patterns in this model are differential ionization and the relative separation of neutrals from ions due to interaction with the solar magnetic field. If species dependent effects are small relative to radius dependent effects, this process can explain in detail both the relative and absolute abundances in the terrestrial planets and carbonaceous chondrites. The electron temperatures predicted by the data are consistent with astrophysical constraints previously derived for the solar nebula, and the timeline of events necessary for this model is consistent with accretion in a gas free environment. If species dependent fractionations are small, or approximately cancel each other, the earth is found to be outgassed by an order of magnitude more efficiently than Venus or Mars.

Hostetler, C. J.↗
NASA NTRS1983

Optimal short range trajectories for helicopters

An optimal flight path algorithm using a simplified altitude state model and an apriori climb-cruise-descent flight profile has been developed and applied to determine minimum fuel and minimum cost trajectories for a helicopter flying a fixed range trajectory. The performance model is based on standard flight manual data and is such that on-line trajectory optimization is feasible with a relatively small computer. The results show that the optimal flight path and optimal cruise altitude can represent a 10 percent fuel saving on a minimum fuel trajectory. The optimal trajectories show considerable variability due to helicopter weight, ambient winds and the relative cost trade-off between time and fuel. In general, 'reasonable' variations from the optimal velocities and cruise altitudes do not significantly degrade the optimal cost.

Slater, G. L.↗
NASA NTRS1984

Wall interference measurements for three-dimensional models in transonic wind tunnels: Experimental difficulties

The purpose is not to provide a detailed discussion of several wall interference experiments, but rather to use these experiments (recently accomplished in the Boeing Transonic Wind Tunnel (BTWT) to illustrate the problems associated with many of the measurements required by current wall interference assessment/correction (WIAC) procedures. The wall correction to lift is emphasized. It is shown that, because conventional tunnels and relatively small models continue to be used, the flow field or flow boundary measurements to be made impose severe requirements on the experiment itself. In some cases, existing instrumentation and test techniques may not be adequate to obtain the data accuracies needed.

Bengelink, R. L.↗
NASA NTRS1989

Engine inlet distortion in a 9.2 percent scaled vectored thrust STOVL model in ground effect

Advanced Short Takeoff/Vertical Landing (STOVL) aircraft which can operate from remote locations, damaged runways, and small air capable ships are being pursued for deployment around the turn of the century. To achieve this goal, a cooperative program has been defined for testing in the NASA Lewis 9- by 15-foot Low Speed Wind Tunnel (LSWT) to establish a database for hot gas ingestion, one of the technologies critical to STOVL. This paper presents results showing the engine inlet distortions (both temperature and pressure) in a 9.2 percent scale Vectored Thrust STOVL model in ground effects. Results are shown for the forward nozzle splay angles of 0, -6, and 18 deg. The model support system had 4 deg of freedom, heated high pressure air for nozzle flow, and a suction system exhaust for inlet flow. The headwind (freestream) velocity was varied from 8 to 23 kn.

Johns, Albert L.↗
NASA NTRS1990

On the Response of the Special Sensor Microwave/Imager to the Marine Environment: Implications for Atmospheric Parameter Retrievals

A reasonably rigorous basis for understanding and extracting the physical information content of Special Sensor Microwave/Imager (SSM/I) satellite images of the marine environment is provided. To this end, a comprehensive algebraic parameterization is developed for the response of the SSM/I to a set of nine atmospheric and ocean surface parameters. The brightness temperature model includes a closed-form approximation to microwave radiative transfer in a non-scattering atmosphere and fitted models for surface emission and scattering based on geometric optics calculations for the roughened sea surface. The combined model is empirically tuned using suitable sets of SSM/I data and coincident surface observations. The brightness temperature model is then used to examine the sensitivity of the SSM/I to realistic variations in the scene being observed and to evaluate the theoretical maximum precision of global SSM/I retrievals of integrated water vapor, integrated cloud liquid water, and surface wind speed. A general minimum-variance method for optimally retrieving geophysical parameters from multichannel brightness temperature measurements is outlined, and several global statistical constraints of the type required by this method are computed. Finally, a unified set of efficient statistical and semi-physical algorithms is presented for obtaining fields of surface wind speed, integrated water vapor, cloud liquid water, and precipitation from SSM/I brightness temperature data. Features include: a semi-physical method for retrieving integrated cloud liquid water at 15 km resolution and with rms errors as small as approximately 0.02 kg/sq m; a 3-channel statistical algorithm for integrated water vapor which was constructed so as to have improved linear response to water vapor and reduced sensitivity to precipitation; and two complementary indices of precipitation activity (based on 37 GHz attenuation and 85 GHz scattering, respectively), each of which are relatively insensitive to variations in other environmental parameters.

Petty, Grant W.↗
NASA NTRS1992

Solar-type xenon - Isotopic abundances in Pesyanoe

Elemental and isotopic abundances of Ar and Xe were measured in three grain-size separates in the dark phase of the enstatite achondrite Pesyanoe by stepwise heating, using a combination of pyrolysis and combustion steps. The data reveal a low-temperature gas fraction with Ar/Xe ratios close to the solar ratio and isotopically similar to solar-type Ar and Xe observed in lunar samples. The gas released at intermediate temperature steps shows that Ar and Xe are isotopically fractionated, compared to the low-temperature components. Pesyanoe does not have excess Ar-40 and fission Xe, which means its parent body was too small for ion reimplantation. It is concluded that solar-type Xe isotopic abundances can be inferred from the low-temperature component. A comparison of Pesyanoe and lunar data shows that isotopic signatures of solar-wind Xe, as sampled at two different points in solar system space and time, are identical within experimental error.

Kim, J. S.↗
NASA NTRS1995

Theoretical overview and modeling of the sodium and potassium atmospheres of the moon

A general theoretical overview for the sources, sinks, gas-surface interactions, and transport dynamics of sodium and potassium in the exospheric atmosphere of the Moon is given. These four factors, which control the spatial distribution of these two alkali-group gases about the Moon, are incorporated in numerical models. The spatial nature and relative importance of the initial source atoms atmosphere (which must be nonthermal to explain observational data) and the ambient (ballistic hopping) atom atmosphere are examined. The transport dynamics, atmospheric structure, and lunar escape of the nonthermal source atoms are time variable with season of the year and lunar phase because of their dependence on the radiation acceleration experienced by sodium and potassium atoms as they resonantly scatter solar photons. The dynamic transport time of fully thermally accomodated ambient atoms along the surface because of solar radiation acceleration (only several percent of surface gravity) is larger than the photoionization lifetimes and hence unimportant in determining the local density, although for potassium the situation is borderline. The sodium model was applied to analyze sodium observations of the sunward brightness profiles acquired near last quarter by Potter & Morgan (1988b) extending from the surface to an altitude of 1200 km, and near first quarter by Mendillo, Baumgardner, & Flynn (1991), extending in altitude from approximately 1430 to approximately 7000 km. The observations at larger altitudes could be fitted only for source atoms having a velocity distribution with a tail that is mildly nonthermal (like an approximately 1000 K Maxwell-Boltzmann distribution). Solar wind sputtering appears to a be a viable source atom mechanism for the sodium observations with photon-simulated desorption also possible but highly uncertain, although micrometeoroid impact vaporization appears to have a source that is too small and too hot, with likely an incorrect angular distribution about the Moon.

Smyth, William H.↗
NASA NTRS2010

Direct CFD Predictions of Low Frequency Sounds Generated by a Helicopter Main Rotor

The use of CFD to directly predict helicopter main rotor noise is shown to be quite promising as an alternative mean for low frequency source noise evaluation. Results using existing state-of-the-art grid structures and finite-difference schemes demonstrated that small perturbation pressures, associated with acoustics radiation, can be extracted with some degree of fidelity. Accuracy of the predictions are demonstrated via comparing to predictions from conventional acoustic analogy-based models, and with measurements obtained from wind tunnel and flight tests for the MD-902 helicopter at several operating conditions. Findings show that the direct CFD approach is quite successfully in yielding low frequency results due to thickness and steady loading noise mechanisms. Mid-to-high frequency contents, due to blade-vortex interactions, are not predicted due to CFD modeling and grid constraints.

Sim, Ben W.↗
NASA NTRS2012

Implications of Adhesion Studies for Dust Mitigation on Thermal Control Surfaces

Experiments measuring the adhesion forces under ultrahigh vacuum conditions (10 (exp -10) torr) between a synthetic volcanic glass and commonly used space exploration materials have recently been described. The glass has a chemistry and surface structure typical of the lunar regolith. It was found that Van der Waals forces between the glass and common spacecraft materials was negligible. Charge transfer between the materials was induced by mechanically striking the spacecraft material pin against the glass plate. No measurable adhesion occurred when striking the highly conducting materials, however, on striking insulating dielectric materials the adhesion increased dramatically. This indicates that electrostatic forces dominate over Van der Waals forces under these conditions. The presence of small amounts of surface contaminants was found to lower adhesive forces by at least two orders of magnitude, and perhaps more. Both particle and space exploration material surfaces will be cleaned by the interaction with the solar wind and other energetic processes and stay clean because of the extremely high vacuum (10 (exp -12) torr) so the atomically clean adhesion values are probably the relevant ones for the lunar surface environment. These results are used to interpret the results of dust mitigation technology experiments utilizing textured surfaces, work function matching surfaces and brushing. They have also been used to reinterpret the results of the Apollo 14 Thermal Degradation Samples experiment.

Gaier, James R.↗
NASA NTRS2018

Compact Mid-Wave Imaging System (CMIS) for Retrieval of Cloud Motion Vectors and Cloud Geometric Heights

The Johns Hopkins University Applied Physics Laboratory (JHU/APL) is developing a compact, light-weight, and low power midwave-infrared (MWIR) imager called the Compact Midwave Imaging Sensor (CMIS), under the support of the NASA Earth Science Technology Office Instrument Incubator Program. The goal of this CMIS instrument development and demonstration project is to increase the technical readiness of CMIS, a multi-spectral sensor capable of retrieving 3D winds and cloud heights 24/7, for a space mission. The CMIS instrument employs an advanced MWIR detector that requires less cooling than traditional technologies and thus permits a compact, low-power design, which enables accommodation on small spacecraft such as CubeSats. CMIS provides the critical midwave component of a multi-spectral sensor suite that includes a high-resolution Day-Night Band and a longwave infrared (LWIR) imager to provide global cloud characterization and theater weather imagery. In this presentation, an overview of the CMIS project, including the high-level sensor design, the concept of operations, and measurement capability will be presented. System performance for a variety of different scenes generated by a cloud resolving model (CRM) will also be discussed.

midwave↗
NASA NTRS1972

Wind tunnel study of slot spoilers for direct lift control

An investigation was conducted in a 300-mph 7- by 10- foot tunnel to obtain data for a slot spoiler direct lift control system. Slot spoilers are believed to have advantages over flap-type direct lift control (DLC) systems because of the small amount of power required for actuation. These tests, run at a Reynolds number of 1,400,000 showed that up to 78 percent of the lift due to flap deflection could be spoiled by opening several spanwise slots within the flaps. For a given lift change the drag change was significantly less than that which would be obtained by a variable flap DLC system. A nozzle-shaped slot was the most effective of the slot shapes tested.

Andrisani, D., II↗

Refine your search to explore more results.