Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “rockets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Ignition Delay Experiments with Small-scale Rocket Engine at Simulated Altitude Conditions Using Various Fuels with Nitric Acid Oxidants / Dezso J. Ladanyi

Ignition delay determinations of several fuels with nitric oxidants were made at simulated altitude conditions utilizing a small-scale rocket engine of approximately 50 pounds thrust. Included in the fuels were aniline, hydrazine hydrate, furfuryl alcohol, furfuryl mercaptan, turpentine, and mixtures of triethylamine with mixed xylidines and diallyaniline. Red fuming, white fuming, and anhydrous nitric acids were used with and without additives. A diallylaniline - triethylamine mixture and a red fuming nitric acid analyzing 3.5 percent water and 16 percent NO2 by weight was found to have a wide temperature-pressure ignition range, yielding average delays from 13 milliseconds at 110 degrees F to 55 milliseconds at -95 degrees F regardless of the initial ambient pressure that ranged from sea-level pressure altitude of 94,000 feet.

XYLIDINE↗
NASA NTRS2001

Rocket sled testing of a prototype terrain-relative navigation system

The next generation of Martian landers (2007 and beyond) will employ a precision soft-landing capability that will make it possible to explore previously inaccessible regions on the surface of Mars. This capability will be enabled by onboard systems that automatically identify and avoid terrain containing steep slopes or rocks exceeding a particular terrain height. JPL is currently developing such a hazard detection and avoidance system; this system will map the landing zone with a scanning laser radar, identify hazards, select a safe landing zone, and then guide the vehicle to the selected landing area. This paper describes how one component of this system-hazard detection-is being tested using a rocket sled and simulated Martian terrain.

lidar↗
NASA NTRS2015

High-Reflectivity Multi-Layer Coatings for the CLASP Sounding Rocket Project

We are planning an international rocket experiment Chromospheric Lyman-Alpha Spectro-Polarimeter (CLASP) is (2015 planned) that Lyman alpha line (Ly alpha line) polarization spectroscopic observations from the sun. The purpose of this experiment, detected with high accuracy of the linear polarization of the Ly alpha lines to 0.1% by using a Hanle effect is to measure the magnetic field of the chromosphere-transition layer directly. For polarization photometric accuracy achieved that approximately 0.1% required for CLASP, it is necessary to realize the monitoring device with a high throughput. On the other hand, Ly alpha line (vacuum ultraviolet rays) have a sensitive characteristics that is absorbed by the material. We therefore set the optical system of the reflection system (transmission only the wavelength plate), each of the mirrors, subjected to high efficiency of the multilayer coating in accordance with the role. Primary mirror diameter of CLASP is about 30 cm, the amount of heat about 30,000 J is about 5 minutes of observation time is coming mainly in the visible light to the telescope. In addition, total flux of the sun visible light overwhelmingly large and about 200 000 times the Ly alpha line wavelength region. Therefore, in terms of thermal management and 0.1% of the photometric measurement accuracy achieved telescope, elimination of the visible light is essential. We therefore, has a high reflectivity (greater than 50%) in Ly alpha line, visible light is a multilayer coating be kept to a low reflectance (less than 5%) (cold mirror coating) was applied to the primary mirror. On the other hand, the efficiency of the polarization analyzer required chromospheric magnetic field measurement (the amount of light) Conventional (magnesium fluoride has long been known as a material for vacuum ultraviolet (MgF2) manufactured ellipsometer; Rs = 22%) about increased to 2.5 times were high efficiency reflective polarizing element analysis. This device, Bridou et al. (2011) is proposed "that is coated with a thin film of the substrate MgF2 and SiO2 fused silica." As a result of the measurement, Rs = 54.5%, to achieve a Rp = 0.3%, high efficiency, of course, capable of taking out only about spolarized light. Other reflective optical elements (the secondary mirror, the diffraction grating-collector mirror), subjected to high-reflection coating of Al + MgF2 (reflectance of about 80%), less than 5% in the entire optical system by these (CCD Science was achieved a high throughput as a device for a vacuum ultraviolet ray of the entire system less than 5% (CCD of QE is not included).

sounding rocket↗
NASA NTRS2016

Status of the Micro-X Sounding Rocket X-Ray Spectrometer

Micro-X is a sounding rocket borne X-ray telescope that utilizes transition edge sensors to perform imaging spectroscopy with a high level of energy resolution. Its 2.1m focal length X-ray optic has an effective area of 300 sq cm, a field of view of 11.8 arcmin, and a bandpass of 0.12.5 keV. The detector array has 128 pixels and an intrinsic energy resolution of 4.5 eV FWHM. The integration of the system has progressed with functional tests of the detectors and electronics complete, and performance characterization of the detectors is underway. We present an update of ongoing progress in preparation for the upcoming launch of the instrument.

X-ray astronomy↗
NASA NTRS2016

Analysis of a Radioisotope Thermal Rocket Engine

The Triton Hopper is a concept for a global hopper vehicle which uses a radioisotope rocket engine and In-situ propellant acquisition to explore the surface of Neptune's moon, Triton. The current Triton Hopper concept stores heated Nitrogen in a spherical tank to be used as the propellant. The aim of the research was to investigate the benefits of storing propellant at ambient temperature and heating it through the use of a thermal block during engine operation, as opposed to storing gas at a high temperature. Lithium, Lithium Fluoride and Beryllium were considered as possible materials for the thermal block. A heat energy analysis indicated that a lithium thermal mass would provide the highest heat energy for a temperature change from 900 Celsius to -100 Celsius. A heat transfer analysis was performed for Nitrogen at -100 Celsius flowing through 1000 passages inside a 1kg lithium thermal block at a temperature of 900 Celsius. The system was analyzed as turbulent flow through a tube with constant surface temperature. The analysis indicated that the propellant reached a maximum temperature of 877 Celsius before entering the nozzle. At this exit temperature, the average specific impulse [I(sub sp)] of the engine was determined to be 157s. Previous studies for the stored heated gas concept suggest that the engine would have an average I(sub sp) of approximately 52s. Thus, the use of a thermal block concept results in a 200 percent engine performance increase. In addition, a tank sizing study was performed to determine if the concept is feasible in terms of mass requirements. The mass for a spherical carbon fiber COPV storing 35kg of nitrogen at an initial temperature of -100 Celsius and a pressure of 1000psia, was determined to be 7.2kg. The specific impulse analysis indicated that the maximum engine performance is obtained for a mass ratio of 5kg of Nitrogen per every 1kg of lithium thermal mass. Thus for 35kg of Nitrogen the total thermal mass would be 7kg. This brings the total mass of the system to 49.2.kg which is less than the 56kg landing payload capacity of the Triton Hopper. Finally, an insulation analysis using 10mm of MLI insulation indicated that a total of 22 watts of heat are lost to the environment. With the heat loss known, the power required to heat the thermal mass to 900 Celsius in 24 days was determined to be 2.15 watts. The study's results allowed us to conclude that the thermal mass concept is the better option due to the performance increase provided, the low power requirement and its compliance with the landing mass requirement of the Triton Hopper.

Radioisotope↗
NASA NTRS2015

Simulation of Liquid Rocket Engine Failure Propagation Using Self-Evolving Scenarios

Traditional probabilistic risk assessment approaches often require failure scenarios to be explicitly defined through event sequences that are then quantified as part of the integrated analysis. This approach becomes difficult when failure propagation paths change as a function of the system operation. Additionally, if the propagation paths represent interactions among even a modest number of components, the scenario count becomes combinatorially intractable. This paper presents an alternate approach for quantifying the probability of failure propagation in such a case. Rather than explicitly defining scenario sequences, simple physical models are created for each of the components. In this way, only the physical states and rules of component interactions must be defined, rather than event sequences for each individual scenario. Initiating failures are introduced into the system, either randomly or as defined by relative likelihood, and the failures cascade through the system via the interaction rules. This process is repeated using Monte Carlo methods and, as a result, the most probable scenarios “self-evolve” in terms of both sequence path and frequency. This approach was applied to failures occurring in the engine compartment of a space launch vehicle with four liquid rocket engines and four high-pressure helium tanks. Each engine was modeled with key components, such as turbomachinery, combustion chamber, propellant lines, and additional support systems. Three test cases were conducted with different high-energy engine failures. End results of interest included an additional engine-out failure and tank burst, which represent the loss-of-mission (LOM) and loss-of-crew (LOC) failure environments, respectively. Observations show that almost every scenario outcome is unique and that many scenarios involve complex chain reactions that are difficult to predict. This validates the usefulness of the modeling approach in assessing the overall risks to the crew during a launch vehicle abort.

Rocket Engine↗
NASA NTRS2020

Analytical Redundancy Using Kalman Filters for Rocket Engine Sensor Validation

The use of sensor redundancy is crucial in aerospace systems to maintain safe, reliable operation. While hardware redundancy is more common in application, analytical redundancy can provide a viable alternative in systems where the installation of multiple redundant sensors is not viable. To this end, the use of Kalman filters to analytically validate sensor measurements within rocket engines was explored. First, a dynamic model of the RS 25 engine, a derivative of the Space Shuttle Main Engine (SSME), was reduced to a subset of relations, focused around the main combustion chamber pressure. These relations were used within the Kalman filter algorithm to generate an estimate of sensor measurements to be compared with true measurements for data validation purposes. By using a bank of Kalman filters, the residuals between the estimated and true measurements were used to detect and isolate sensor faults. Through fault simulations, the sensor validation performance of this Kalman filter bank design was compared to a hardware redundancy check. Sensor bias and drift faults of various magnitudes were injected into nominal RS 25 engine test data. Results for both approaches show comparable fault detection with most bias faults found nearly instantaneously by both algorithms. Drift fault detection results show certain cases where one algorithm is faster than the other. The key advantage of the Kalman filter algorithm is shown in fault isolation performance where it can isolate faults between two redundant sensors while the hardware redundancy comparisons cannot.

sensors↗
NASA NTRSDate not supplied

Component Applications using Metal Additive Manufacturing Techniques and Materials for Rocket Propulsion

The NASA Marshall Space Flight Center (MSFC) has been involved with various forms of metallic additive manufacturing for use in liquid rocket engine component design, development, and testing since 2010. These AM techniques have been demonstrated to significantly reduce hardware cost, shorten fabrication schedules, increase reliability by reducing the number of joints, and improve hardware performance by allowing fabrication of designs not feasible by conventional means. The focus at the NASA MSFC for these metal additive manufacturing techniques include laser powder-bed fusion (L-PBF), blown powder directed energy deposition (DED) and arc-based deposition. A variety of components have been evaluated and tested including thrust chamber injectors, injector components such as faceplates, regeneratively-cooled combustion chambers, regeneratively-cooled nozzles, gas generator and preburner hardware, and augmented spark igniters. To support these component applications in harsh environments, NASA has advanced a variety of “standard” additive manufacturing alloys such as those in the superalloy-family and also evolved new alloys including GRCop-84, GRCop-42, NASA HR-1, and JBK-75. The purpose of this presentation is to discuss the various programs at the NASA MSFC using AM to develop, fabricate, and test combustion devices hardware and the evolution of the new additive alloys. Additional information will be provided on the development of multi-metallic additive manufacturing, post-processing of AM techniques including surface enhancements (polishing) techniques, material and process characterization, future development programs, and dissemination of data to industry partners.

Additive Manufacturing↗
NASA NTRS2020

Physical Simulation Of Rocket Exhaust Aerodynamics Using Heated Ethane: Prototypical Experiments

An inaugural experimental investigation into the use of heated ethane as a motive fluid for subscale simulation of rocket exhaust plume aerodynamics has been conducted. A small, self-contained, hydrocarbon aerodynamics test stand was designed and fabricated for this purpose. Testing was performed on an aerodynamic system comprised of a 77:1 upper stage nozzle contour coupled with a passive second-throat supersonic diffuser, specifically selected for its known LOX/GH2 hot-fire performance and complex shock structure. Effects of ethane purity and stagnation temperature on the accuracy of flow field replication have been examined. All major flow features present in hot-fire tests were reproduced in heated ethane with start and unstart pressure ratio errors of approximately +4% and -5%, respectively. Steady-state test cell pressure ratio errors of ±0.5% were shown to be readily achievable when the stagnation temperature was well-controlled. Ambient-temperature nitrogen testing was also conducted for the purpose of direct comparison of the ethane method to conventional cold-flow techniques. However, its higher isentropic exponent prevented the diffuser from achieving start.

rocket↗
NASA NTRS1994

Characterization of Hybrid Rocket Internal Heat Flux and HTPB Fuel Pyrolysis

None given. From statement of problem:The broad nature of this work has been to extend our understanding of the nature of the conventional or classical hybrid rocket combustion process (fuel decomposition, heat and mass transfer, and chemical reaction), and the critical engineering parameters that define this process.

rocket↗
NASA NTRSDate not supplied

Advancement of Metal Additive Manufacturing Processes and Alloys for Rocket Propulsion Applications

NASA has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the 2000’s. Several efforts have focused on the understanding of AM processes through material characterization and testing, standards development, component fabrication, and infusion into development and flight applications. While many common aerospace alloys have been and continue to be a focus of ongoing development, the need for custom-alloy developments for high performance applications enabled by various AM processes has been realized. The applications being targeted are liquid rocket engines with high heat fluxes, high pressure, and that utilize propellants such as hydrogen, which can degrade the alloy. NASA has recently focused on the development and advancement of novel alloy advancement using AM for use in these harsh environments, such as GRCop-42, GRCop-84, NASA HR-1, and JBK-75. These alloys have been evaluated using powder bed fusion (PBF), directed energy deposition (DED), and solid-state AM processes. The results from these processes have demonstrated that AM can enable rapid development of new alloy systems that can yield higher performances across various metal AM processes. These alloys have undergone the fundamental metallurgical evaluations, heat treatment study, and microstructure characterization and mechanical testing campaign. This, combined with direct application-specific component fabrication and hot-fire testing, enabled the increase of the Technology Readiness Level (TRL). This presentation will provide a background and overview of various AM-enabled novel alloys, a comparison across the AM processes, and development including metallurgical and mechanical property studies. It will also cover the latest advancement in the parallel component development and testing and future developments. The goal of these alloy development and use of various AM processes is to allow for technology infusion into NASA and commercial spaceflight missions as well as to establish and sustain the needed commercial AM supply chain.

Additive Manufacturing↗
NASA NTRSDate not supplied

Aluminum Borohydride Ammines as Fuels for Hybrid Rocket Motors: Theoretical Performance and Particle Synthesis

The aluminum borohydride ammines, Al(BH4)3·XNH3, are a family of complexes between aluminum borohydride and ammonia for which up to six moles of ammonia can be complexed per mole of aluminum borohydride. Two of these complexes, the diammine (X = 2) and hexammine (X = 6) are of particular interest for use in hybrid rocket motors as additives and stand alone fuels. This study compares these compounds against other metal hydride for their potential as additives to increase the regression rate of solid fuel grains. The theoretical performance of the diammine as a stand alone fuel paired with non-toxic oxidizers is also investigated. The low temperature and good performance of these combinations make them of interest for low cost orbital maneuvering thrusters. Finally, the synthesis process for Al(BH4)3·6NH3 is discussed and TGA/DSC results are presented.

hybrid rockets↗
NASA NTRSDate not supplied

Aluminum borohydride ammines as fuels for hybrid rocket motors: theoretical performance and particle synthesis

The aluminum borohydride ammines, Al(BH4)3·XNH3, are a family of complexes between aluminum borohydride and ammonia for which up to six moles of ammonia can be complexed per mole of aluminum borohydride. Two of these complexes, the diammine (X = 2) and hexammine (X = 6) are of particular interest for use in hybrid rocket motors as particle additives and stand alone fuels. This study compares these compounds against other metal hydrides for their potential to increase the regression rate of solid fuel grains. The theoretical performance of the diammine as a stand alone fuel paired with non-toxic oxidizers is also investigated. The low temperature and good performance of these combinations make them of interest for low cost orbital maneuvering thrusters. Finally, results on the synthesis of Al(BH4)3·6NH3 and its thermal characterization are presented.

hybrid rockets↗
NASA NTRSDate not supplied

Early Progress Toward the Feasibility of the Centrifugal Nuclear Thermal Rocket

The Centrifugal Nuclear Thermal Rocket (CNTR) is a Nuclear Thermal Propulsion (NTP) concept designed to heat propellant directly by the reactor fuel. The primary difference between the CNTR concept and traditional NTP systems is that rather than using traditional solid fuel elements, the CNTR uses liquid fuel with the liquid contained in rotating cylinders by centrifugal force. If the concept can be successfully realized, the CNTR would have a high specific impulse (~1800 seconds) at high thrust, which may enable (i) viable near-term human Mars exploration by reducing round-trip times to 420 days and (ii) direct injection orbits for scientific missions to the Solar System outer planets and potentially Kuiper Belt objects. The CNTR could also use storable propellants such as ammonia, methane, or hydrazine at an Isp of ~900 seconds, enabling long-term in-space storage of a dormant system. Significant engineering challenges must be addressed to establish the technical viability of the CNTR. Research is presently underway to determine resolutions for these engineering challenges. In particular, research has begun on the analytical modeling and simulation of the two-phase heat transfer between the liquid metallic uranium fuel and the gaseous propellant. A paper was presented at the 2021 IAC which described these challenges and the study plan to address them. This paper describes the analytical and experimental progress to date toward resolving these challenges and establishing the engineering feasibility of the CNTR technology

High Performance Nuclear Thermal Propulsion NTP SN↗
NASA NTRS2014

Identification of Noise Sources in a Rocket Engine Test Stand using Microphone Phased Array

A new, phased array of microphones, suitable for the harsh environment of a rocket launch, was built and tested during a static firing of a RS-25 engine. It uses 70 piezo-resistive, dynamic pressure sensors, optimally distributed on a 10.5ft diameter open frame dome structure, and has a 200-ft long cable bundle to carry the signals to a weather-protected cabinet containing the data systems. The test stand was imaged using an infra-red camera and a visible wavelength camera, and the beamformed noise maps were superimposed on the photographs. The first-time data from a full-scale engine test stand showed that the plume deflector at the bottom of the engine to be the primary noise source. The openings of the test stand around the nozzle exit were also found to be noise sources particularly at higher frequencies. The final goal is to use the array during NASA’s Artemis-II launch at Kennedy Space Center.

Identification of Noise Source↗

Refine your search to explore more results.